Mikrotikls SIA R11E2HPND DIGITAL TRANSMISSION SYSTEM MODULE User Manual

Mikrotikls SIA DIGITAL TRANSMISSION SYSTEM MODULE

User Manual

Federal Communication Commission Interference Statement (FCC ID: TV7R11E2HPND) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. IMPORTANT: Exposure to Radio Frequency Radiation. The maximum permissible exposure report has been created for this module, which shows the minimum distances for public use as 142 cm when using a 24-dBi gain antenna. Under such configuration, the FCC radiation exposure limits set forth for a general population/uncontrolled environment can be satisfied. OEM statement. This module is intended for OEM installations only. As such the OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove install or modify the module. This module is limited to installations in mobile or fixed applications. OEM integrators may utilize antennas of like an equal or lesser gain as appearing in the table below (for further infomraiton on this topic refer to 47CFR, paragraph 15.204(c)(4)). The MikroTik OEM RF Module complies with Part 15 of the FCC rules and regulations. OEM Modules have been certified by the FCC for use with other products without any further certification (as per 47CFR section 2.1091). Separate approval is required for other operating configurations including portable configurations with respect to 47CFR paragraph 2.1093 and different antenna configurations. The OEM is required to comply with all 47CFR labeling instructions and requirements for the finished products. Changes or modifications not expressly approved by MikroTik could void the OEM authority to install or operate the equipment. OEMs must test their final product to comply with unintentional radiators (47CFR section 15.107 and 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules. Warning: the OEM must ensure that the end product complies with FCC labeling requirements. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate MikroTik OEM RF Module FCC identifier for this product as well as any other required FCC notices as presented below. Contains FCC ID: TV7R11E2HPND This enclosed device complies with 47CFR paragraph 15 C of the FCC rules and regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Labeling and text information should be of a size of type large enough to be readily legible, consistent with the dimensions of the equipment and the label.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. Warning: This device has been tested with a MMCX connector and antennas as listed in the table above. When integrated into the OEM products, these fixed antennas require professional installation preventing end users from replacing them with non-compliant antennas. List of approved antennas:  Omni Directional, WLO-2450-15, 15 dBi;  Omni Directional HP, ODH 24-13, 13dBi;  Panel, WLP-2450-20, 20 dBi;  Sector, SA-24-90-17-WB, 17 dBi;  Dish, DC 24-HD-PFIP, 24 dBi; Antennas of same type and lower gain than those listed above may be used in compliance with certification. Antenna Installation Warning: It is installer's responsibility to ensure that only those antennas certified with the product are used for operation in the United States (or where FCC rules apply). The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 paragraph 15.204. It is the installers’ responsibility to configure the output power level according to country regulations and antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. Antenna Model Gain (dBi) Maximum Transmit Power Per Chain Total (dBm) Omni Directional WLO-2450-15 15 24 27 Omni Directional HP ODH 24-13 13 24 27 Panel WLP-2450-20 20 22 25 Sector SA 24-90-17-WB 17 23 26 Dish DC 24-HD-PFIP 24 21 24

Navigation menu