Mikrotikls SIA R11E2HPND DIGITAL TRANSMISSION SYSTEM MODULE User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2187652
Application ID	FgSfrz9O4boTNIZ/oVmcLA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.77kB (72171 bits)
Date Submitted	2014-02-12 00:00:00
Date Available	2014-02-26 00:00:00
Creation Date	2014-02-07 13:25:28
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-02-07 13:25:28
Document Title	User Manual
Document Creator	Microsoft® Word 2010

Federal Communication Commission Interference Statement
(FCC ID: TV7R11E2HPND)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT: Exposure to Radio Frequency Radiation.
The maximum permissible exposure report has been created for this module, which shows the
minimum distances for public use as 142 cm when using a 24-dBi gain antenna. Under such
configuration, the FCC radiation exposure limits set forth for a general population/uncontrolled
environment can be satisfied.
OEM statement. This module is intended for OEM installations only. As such the OEM
integrator is responsible for ensuring that the end-user has no manual instructions to remove
install or modify the module. This module is limited to installations in mobile or fixed
applications. OEM integrators may utilize antennas of like an equal or lesser gain as appearing
in the table below (for further infomraiton on this topic refer to 47CFR, paragraph
15.204(c)(4)). The MikroTik OEM RF Module complies with Part 15 of the FCC rules and
regulations.
OEM Modules have been certified by the FCC for use with other products without any further
certification (as per 47CFR section 2.1091). Separate approval is required for other operating
configurations including portable configurations with respect to 47CFR paragraph 2.1093 and
different antenna configurations. The OEM is required to comply with all 47CFR labeling
instructions and requirements for the finished products.
Changes or modifications not expressly approved by MikroTik could void the OEM authority to
install or operate the equipment. OEMs must test their final product to comply with
unintentional radiators (47CFR section 15.107 and 15.109) before declaring compliance of
their final product to Part 15 of the FCC Rules.
Warning: the OEM must ensure that the end product complies with FCC labeling
requirements. This includes a clearly visible label on the outside of the OEM enclosure
specifying the appropriate MikroTik OEM RF Module FCC identifier for this product as well as
any other required FCC notices as presented below.
Contains FCC ID: TV7R11E2HPND
This enclosed device complies with 47CFR paragraph 15 C of the FCC rules and regulations.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Labeling and text information should be of a size of type large enough to be readily legible,
consistent with the dimensions of the equipment and the label.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other
antenna or transmitter.
Warning: This device has been tested with a MMCX connector and antennas as listed in the
table above. When integrated into the OEM products, these fixed antennas require professional
installation preventing end users from replacing them with non-compliant antennas.
List of approved antennas:





Omni Directional, WLO-2450-15, 15 dBi;
Omni Directional HP, ODH 24-13, 13dBi;
Panel, WLP-2450-20, 20 dBi;
Sector, SA-24-90-17-WB, 17 dBi;
Dish, DC 24-HD-PFIP, 24 dBi;
Antennas of same type and lower gain than those listed above may be used in compliance with
certification.
Antenna Installation
Warning: It is installer's responsibility to ensure that only those antennas certified with the
product are used for operation in the United States (or where FCC rules apply). The use of any
antenna other than those certified with the product is expressly forbidden in accordance to FCC
rules CFR47 paragraph 15.204. It is the installers’ responsibility to configure the output power
level according to country regulations and antenna type. Professional installation is required of
equipment with connectors to ensure compliance with health and safety issues.
Antenna
Model
Gain
Maximum Transmit Power
(dBi)
Per Chain
Total (dBm)
Omni Directional
WLO-2450-15
15
24
27
Omni Directional HP
ODH 24-13
13
24
27
Panel
WLP-2450-20
20
22
25
Sector
SA 24-90-17-WB
17
23
26
Dish
DC 24-HD-PFIP
24
21
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Producer                        : Microsoft® Word 2010
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:02:07 13:25:28-06:00
Modify Date                     : 2014:02:07 13:25:28-06:00

EXIF Metadata provided by EXIF.tools