Miller Edge MWCK02 Safety Device Transmitter / Receiver User Manual Communicator Inst 7 31 03 FINAL

Download:
Mirror Download [FCC.gov]
Document ID	354271
Application ID	SDJyzIjUqVcgcpN9wBEUBw==
Document Description	OPerational MAnual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.44kB (17992 bits)
Date Submitted	2003-09-08 00:00:00
Date Available	2003-09-17 00:00:00
Creation Date	2003-08-08 10:42:39
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2003-08-08 10:42:39
Document Title	Communicator Inst 7-31-03 FINAL
Document Creator	QuarkXPressª: AdobePS 8.7.3 (301)
Document Author:	RayS

The Communicator
Wireless Transmitter/Receiver
Installation Instructions
TO REDUCE RISK OF SEVERE INJURY OR DEATH;
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
WARNING!
TO PREVENT ELECTROCUTION DISCONNECT POWER AT FUSE BOX OR CIRCUIT
BREAKER AND DOOR OPENER BEFORE WIRING PERMANENTLY.
IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY.
FOLLOW ALL LOCAL BUILDING CODES AND NATIONAL ELECTRICAL CODES.
TRANSMITTER INSTALLATION:
1- Remove lid from top of the MWCT-01 Transmitter to reveal mounting holes. Position the Transmitter near
the bottom of the door and mark the mounting hole locations.
2. Remove the Transmitter from door, drill holes and mount the Transmitter with screws supplied.
3- Loosen wire fitting nut and feed the 4-wire sensing edge leads into the Transmitter housing trimming off excess wire.
4- Attach the 4-lead wires to the large green two-part terminal block connector as White White, Black Black.
Tighten the wire fitting nut to assure water tight connection.
5- Adjust Dip Switches: 1= Channel Selector
4= Address Selector
2= Channel Selector
5= Address Selector
3= NOT USED
(SEE FIGURE 1 FOR SWITCH CONFIGURATIONS.)
5- Be sure that the battery strap is connected and insert 9 Volt battery into the lid of the unit, and replace the lid.
The Green LED light should light up indicating that the unit is functioning properly.
RECEIVER INSTALLATION:
1- Hold the MWCR-01 Receiver up near the operator, mark and drill mounting holes.
2- Attach a 24VAC (at least 200mA) source to the red & black wires. A 12-28 VDC source may also be used.
Polarity does not matter here.
3- Connect channel 1 to the white wires, channel 2 (if present) to the yellow wires, channel 3 to orange wires.
The output relays will bear a load of 1A at 24VAC and 0.5A at 110VAC. Each channel has an associated
YELLOW LED. The LED is illuminated when the channel is in a SAFE operating condition and will go out
under fault condition.
4- There is a GREEN LED located near the dip switches which indicates SIGNAL ACQUIRED. It should turn on within
a ew seconds of the transmitter contacting the receiver.
5- There is also a RED LED located in the same place, which signals MAINTENANCE REQUIRED. It will illuminate
when there is a condition such as low battery or tampering.
MILLER EDGE, INC. • P.O. Box 159 • West Grove, PA 19390 • 610-869-4422 • Fax: 610-869-4423 • 1-800-220-EDGE • www.milleredge.com
MILLER EDGE, INC. • 6809 South Harl Avenue • Suite A • Tempe, AZ 85283 • 480-755-3565 • Fax: 480-755-3558 • 1-800-887-EDGE
REV. 7-31-03
RECEIVER INSTALLATION Cont.
6- Adjust Dip Switches: 1=Mode Selector
4= Address Selector
2= Mode Selector
5= Address Selector
3= NOT USED
(SEE FIGURE 1 FOR SWITCH CONFIGURATIONS.)
Modes are as follows:
Switch 1 down, Switch 2 down: Mode Selected for Signal from one (1) Transmitter
Switch 1 up, Switch 2 down: Mode Selected for Signal from two (2) Transmitters
Switch 1 up, Switch 2 up: Mode Selected for Signal from two (3) Transmitters
7- Mount the Receiver near the operator using the 2 screws supplied.
8- Attach Coax Rigid Wire antenna.
9- Test door/gate operation to see that the system is functioning properly.
FIGURE 1
1 RECEIVER W/ 1 TRANSMITTER
RECEIVER SWITCH SETTING
ON
TRANSMITTER SWITCH SETTING
ON
OFF(0)
OFF(0)
SWITCH SHOWN IN
DOWN (OFF) POSITION
1 RECEIVER W/ 2 TRANSMITTERS
TRANSMITTER #1
SWITCH SETTINGS
RECEIVER SWITCH SETTING
ON
ON
OFF(0)
TRANSMITTER #2
SWITCH SETTINGS
ON
OFF(0)
OFF(0)
1 RECEIVER W/ 3 TRANSMITTERS
RECEIVER SWITCH SETTING
ON
ON
OFF(0)
TRANSMITTER #2
SWITCH SETTINGS
TRANSMITTER #1
SWITCH SETTINGS
ON
TRANSMITTER #3
SWITCH SETTINGS
ON
OFF(0)
OFF(0)
OFF(0)
LED DIAGNOSTICS (Inside Receiver Enclosure)
POWER
(Green)
CHANNEL 1
RELAY
CHANNEL 2
RELAY
CHANNEL 3
RELAY
NOTE: RELAY LIGHTS ARE YELLOW
MILLER EDGE, INC. • P.O. Box 159 • West Grove, PA 19390 • 610-869-4422 • Fax: 610-869-4423 • 1-800-220-EDGE • www.milleredge.com
MILLER EDGE, INC. • 6809 South Harl Avenue • Suite A • Tempe, AZ 85283 • 480-755-3565 • Fax: 480-755-3558 • 1-800-887-EDGE

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:08:08 10:42:39-04:00
Modify Date                     : 2003:08:08 10:42:39-04:00
Page Count                      : 2
Creation Date                   : 2003:08:08 14:42:39Z
Mod Date                        : 2003:08:08 14:42:39Z
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : RayS
Metadata Date                   : 2003:08:08 14:42:39Z
Creator                         : RayS
Title                           : Communicator Inst 7-31-03 FINAL

EXIF Metadata provided by EXIF.tools