Miltel Communications SPEEDHPRX450 Licenced Non-Broadcast Transmitter User Manual Chapter Number
Miltel Communications Ltd Licenced Non-Broadcast Transmitter Chapter Number
users manual
Speed HPRx450 Wireless Data Link for Data Transfer FCC ID: MLLSPEEDHPRX450 User Manual Miltel Communications Ltd. December 2002 Table of Contents Chapter 1 Introduction.................................................................................................3 1.1 Purpose and Use ............................................................................................3 1.2 System General Description ...........................................................................3 1.3 Theory of Operation........................................................................................4 Chapter 2 Technical Characteristics................................................................................5 2.1 2.1.1 2.1.2 Technical Specification ...................................................................................5 Electrical .........................................................................................................5 Physical...........................................................................................................6 2.2 Label Contents................................................................................................6 Chapter 3 Installation Instructions ...................................................................................7 3.1 General ...........................................................................................................7 3.2 Installation.......................................................................................................7 Chapter 1 Introduction 1.1 Purpose and Use The Speed HPRx450 (FCC ID: MLLSPEEDHPRX450) is a data link transceiver that is used for data transfer in Miltel’s utility consumption readings collection system. This device is installed on-site by a professional field technician, thus it includes technical terms. The equipment is not to be installed by a non-professional individual that has not been trained and authorized. 1.2 System General Description The Speed HPRx450 system is a computerized fully automatic radio device. It requires no human intervention after initial installation. The device acts as a storeand-forward radio relay. The Speed HPRx450 captures any transmission from a Speed HPTx transmitter and, after validating the message, transmits the message again. The Speed HPRx450 relays information from meter reading transmitters to regional concentrators (which are equipped with a radio receiver). The concentrator transfers the data to the central computer for data collection and for further analysis and reporting. 1.3 Theory of Operation The Speed HPRx450 is the intermediate link in the meter readings data collection system. It is an independent unit that operates as a repeater (radio relay). Figure 2-1 (see below) shows a typical installation of a Speed HPRx450 unit. The device is powered by a 12 volt power supply or by a solar powered battery. The Speed HPRx450 operates its radio receiver on a continuous basis until it receives a message from a nearby transmitter. After capturing the transmitted data message, it sends out an identical message which is forwarded to the regional concentrator. Figure 1-1: Speed HPRx450 Typical Installation (shown here with optional solar panels) Chapter 2 Technical Characteristics 2.1 Technical Specification 2.1.1 Electrical Max Effective Radiated Power (ERP) 43 mW (Complies with FCC 90.205(g) ) Output frequency 450-470 MHz Carrier wave modulation 2 Level FSK Power supply Lithium battery, 3.6 Volt Receiver Sensitivity -117 dbm 2.1.2 Physical Operating temperature -30°C ÷+50°C Water Resistance Splash resistance (IP-64) Length 16 cm. Width 12 cm. Depth 7.5 cm. Weight (excluding clamp) 650 gr. Weight (including clamp) 900 gr. Clamp material Stainless steel 2.2 Label Contents (see file: Speed HPRx450 ID Label) FCC ID: MLLSPEEDHPRX450 Model :Speed HPRx450 S/N: YY-nnnnnn Made in Israel Miltel Communications Ltd. Figure 2-1: Label Design Chapter 3 Installation Instructions 3.1 General The Speed HPRx450 is installed by a professional technician. 3.2 Installation For on-site installation of the Speed HPRx450 device, proceed as follows: 1) Loosen the four screws fastening the unit's box and open the box cover. 2) Connect the 12 volt DC power supply (use only U/L approved power supply) 3) Install screws and mount to wall or to mast 4) Close case 5) Install antenna on a mast using the clamp provided Please Note: FCC RF exposure: Antenna Installation: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not exceed an antenna gain of 3 dBi. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 6) Connect the Coax cable at both ends – to the repeater and to the antenna 7) Perform functional radio test by using a Speed HPTx transmitter. Verify that the message is relayed by the repeater to the concentrator. Whenever possible, the repeater should be installed indoors. If outdoor installation is required, the repeater should be installed within a weatherized enclosure.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Producer : Acrobat Distiller 4.05 for Windows Creator : Microsoft Word 9.0 Modify Date : 2003:02:02 12:41:53+02:00 Author : rivka Title : Chapter Number Create Date : 2003:02:02 12:41:43 Page Count : 8 Page Mode : UseNoneEXIF Metadata provided by EXIF.tools