Mindray BIO Medical electronics RF013B-MR-001 Remote Control User Manual

Shenzhen Mindray BIO-Medical electronics Co.,LTD. Remote Control

User Manual

Product Information
Intended Use
The remote keypad is intended to be used with Mindrays BeneView T series and
BeneVision N series patient monitors. The user shall be responsible for ensuring
the compatibility between the remote keypad and the monitoring devices
by either referring to this instructions for use or contacting us before use. The
remote keypad must be used by trained clinical personnel.
Precautions
zCheck the remote keypad and accessories before use. Do not use
the remote keypad in case of damage, block, deterioration or visible
contamination.
zDisposal of the remote keypad and accessories shall comply with applicable
regulations. Do not dispose randomly.
Warnings
zThe remote keypad must be used by trained clinical personnel.
zThe remote keypad is for indoor use only.
zDo not expose to moisture, liquid, or heat environment.
zKeep the keypad with special care after use to avoid unintended
operation.
Overview of The Remote Keypad
No. Key Name Description
1Alarm Reset Key Acknowledges the ongoing alarm.
For details, see "Alarms" in BeneView T series
or BeneVision N series patient monitor
operator's manual.
2 Alarm Pause Key Pauses the current alarm.
For details, see “Alarms” in BeneView
T series or BeneVision N series patient
monitor operator’s manual.
3 Up Arrow Key Moves the highlight bar up.
4 Right Arrow Key
(only for BeneVision N series
patient monitors)
Switches the screen.
5 Right Arrow Key
(only for BeneVision N series
patient monitors)
Switches the screen.
No. Key Name Description
6 Enter Key Enters a menu or confirms a selection.
7 Down Arrow Key Moves the highlight bar down.
8Standby Key Enters the standby mode.
9 Start/Stop NIBP Key Starts an NIBP measurement or stops the
current NIBP measuremet.
10 Zero IBP Key Displays the Zero IBP menu.
11 Manual Event Key Manually Triggers a event.
12 Multifunction Mouse Key
zWhen the mouse is inactivated, use this
key to activate the mouse.
zWhen the mouse is activated, use this
key to locate the cursor.
If you carry out no operations within one
minute after activating the mouse, the
mouse will be inactivated.
13 Main Screen/Main Menu Key Backs to the main screen or main menu.
Preparing the Patient Monitor
(for BeneView T series patient monitors)
The patient monitor shall be properly configured for the use of the remote
keypad. Ask the authorized service personnel to perform the configuration.
Note
zThis operation needs password and is for authorized service personnel
only. Do not configure it yourself.
zIf the corresponding configuration item could not be found in the
configuration menu, ask the authorized service personnel to upgrade the
system software to the latest version first.
Preparing the Remote Keypad
Preparing the receiver
1. Open the battery compartment, and take the receiver out.
2. Plug the receiver to the USB connector on the rear panel of the patient
monitor.
Note
zDo not plug the receiver to the USB connector on the BeneView T series
patient monitor used for connecting iView system or external display, or
to the USB connector on the BeneVision N series patient monitor used for
connecting iView system.
Installing battery
Warnings !
zKeep batteries away from heat, sunshine, or fire. Never discard batteries in
fire.
zWhen the remote keypad is not used for long periods, remove the
battery.
zMake sure that the patient monitor has been properly configured.
zThe remote keypad is effective once the battery is installed. Keep the
remote keypad with special care every time you finish your operation to
avoid any unintended operation.
1. Insert an AAA battery with correct polarity (+/-).
2. Close the battery compartment.
www.mindray.com
Mindray Building, Keji 12th Road South, Hi-tech Industrial Park,
Nanshan, Shenzhen 518057 P.R. China
Tel:+86 755 81888998 Fax:+86 755 26582680 E-mail: service@mindray.com
Instructions For Use
1
4
6
7
8
10
12
2
3
5
9
11
13
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with theinstructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1)this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
CE Statement
Remote Control RF013B-MR-001
Manufacturer: Fenito Electronic Technology (Shenzhen) Co., Ltd, Hereby ,
Fenito Electronic Technology (Shenzhen) Co., Ltd hereby declares that this Remote Control
RF013B-MR-001 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Dispose of used batteries according to the instructions.
Use the Remote Control in the environment with the temperature between 0 and 50 .
Risk of explosion if battery is replaced by an incorrect type.

Navigation menu