| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2724683 |
| Application ID | C0Jih1nksaC3WDzdmNPnGA== |
| Document Description | UserManual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 12.63kB (157863 bits) |
| Date Submitted | 2015-08-25 00:00:00 |
| Date Available | 2015-08-25 00:00:00 |
| Creation Date | 2015-08-17 14:17:50 |
| Producing Software | Acrobat Distiller 10.1.0 (Windows) |
| Document Lastmod | 2015-08-25 16:49:50 |
| Document Title | Microsoft Word - Panlink II User Manual |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | ls |
1.1 General Decription
Panlink II module consists of a BT module, crystal and antenna connector. This module can
change UART signal to wireless signal using Bluetooth low energy technology. This module uses
external antenna via a Antenna connector.
Panlink II communication type is piconet, which means Panlink II transfers data to another
Panklink(one is master, the other one is salve).
When transfering data from master to slave, data was given to master by UART.
Then
master Panlink II controls signal, frames, radiation power and transmits them via the antenna to
slave Panlink II. Slave Panlink II get RF signal via the antenna and resolve it to data.
When transfering data from slave to master, data was given to master by UART.
Then slave
Panlink II controls signal, frames, radiation power and transmits them via the antenna to master
Panlink II. Master Panlink II get RF signal via the antenna and resolve it to data.
And there are some requisition for end-user as below,
圃
The module is limited to OEM installation ONLY;
圃
The OEM integrators is responsible for ensuring that end-user has no manual
instructions to remove or install module;
圃
The module is limited to installation in mobile or fixed application
圃
The separate approval is required for all other operating configurations, including
portable configuration with respect to Part 2.1093 and different antenna configurations;
圃
The host manufacturer is responsible for ensuring that after the module is installed and
operational the host continues to be compliant with the Part 15B unintentional radiator
requirements
1.2 Block diagram
1.3 Interface and pin definition
No.
Pin name
Type
description
1 to 8
NC
No use
DC
Debug clock
10
DD
Debug data
11
SLEEP_OUT/P3_0
Wakeup out
12
VDD
Power
Power in
13
GND
Power
ground
14
Reset
RSTN
Reset in
15
Wake/P0_3
Wake up input
16
UART_RXD0
Uart in, baud rate is
115200
17
UART_TXD0
Uart out, baud rate is
115200
18
nCS1/CTSn1/P1_2
I/O
Reserved
19
CLK1/RTSn1/P1_3
I/O
Reserved
20
MOSI1/TXD1/P1_1
I/O
Reserved
21
MISO1/RXD1/P1_0
I/O
Reserved
22
CD
Module detect pin
23
RF Connector
RF
Connect
to
antenna
1.4 Operation specification
ABSOLUTE MAXIMUM RATINGS
Over operating room temperature range (unless otherwise noted)
Item
VALUE
UNIT
Supply voltage range
-0.3 to 3.9
Voltage range to any of digital
-0.3 to VDD + 0.3,
<3.9
pins
Storage temperature range
℃
-40 to +85
RECOMMENDED OPERATING CONDITIONS
Over operating room temperature range (unless otherwise noted)
Item
MIN
Supply
voltage
NOM
MAX
UNIT
2.4
3.6
-20
+70
℃
range
Operational
temperature range
1.5 Wireless specifications
Protocol：Bluetooth low energy 4.0
Modulation mode：GFSK
Operating frequency：2402 ~ 2480MHz(40 channels)
Channel spacing：2MHz
Wireless baud rate(data rate)： 1Mbps
Output power (transfer power)：
Data security ： 128bit AES
≤2.5mW
1.6 Mechanical and package description
Dimension is 9.6mm*13.9mm*2.3mm,
and package type is SMT.
external
This device and its antenna must not be located or operating in conjunction with any other
antenna and transmitter.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference
received,
including
interference
that
may
cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐Consult the dealer or an experienced radio/TV technician for help important announcement
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following" Contains FCC ID:
ZLZTDBTSE " and Contains IC: 9726A‐TDBTSE. The FCC part 15.19 statement below has to also be
available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause undesired
operation. A user manual with the end product must clearly indicate the operating requirements
and conditions that must be observed to ensure compliance with current FCC RF exposure
guidelines. The end product with an embedded Panlink II Module may also need to pass the
FCC Part 15 unintentional emission testing requirements and be properly authorized
per FCC Part 15.
To comply with FCC regulations limiting both maximum RF output power and human exposure to
RF radiation, the maximum antenna gain including cable loss in general exposure condition must
not exceed 3.5dBi.
The modular used RP‐SMA antenna connector and tested 3 antennas,
Antenna
Antenna Type
Maximum Antenna Gain
Antenna 1
FPC
2dBi
Antenna 2
Dipole
3.5dBi
Antenna 3
FPC
1dBi
If end users use others antennas except stated, end‐users need test radiated emission, RF
exposure refer to FCC C2PC rules.
‐ English: This device complies with Industry Canada licence‐exempt RSS standard(s). Operation
is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference, including interference that may cause undesired operation
of the device. The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout
brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le
fonctionnement.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : No
Author : ls
Create Date : 2015:08:17 14:17:50+08:00
Modify Date : 2015:08:25 16:49:50+08:00
Has XFA : No
XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool : PScript5.dll Version 5.2.2
Metadata Date : 2015:08:25 16:49:50+08:00
Format : application/pdf
Title : Microsoft Word - Panlink II User Manual
Creator : ls
Producer : Acrobat Distiller 10.1.0 (Windows)
Document ID : uuid:a07af137-8c96-4739-ae91-1d629a97c71f
Instance ID : uuid:2ba7f1b3-d5e7-4003-bbcb-96e46a218d5a
Page Count : 6
EXIF Metadata provided by EXIF.tools