Mindray BIO Medical electronics WM1010BGN10 Cyberlink User Manual Cyberlink Wireless LAN Module datasheet

Shenzhen Mindray BIO-Medical electronics Co.,LTD. Cyberlink Cyberlink Wireless LAN Module datasheet

Users manual

KF-XXXX-X-XXX-版本 No. Pin name Type System Description 1 SD_CLK I WLAN SDIO Clock. 2 VIN I Common 3.3V Power supply input. 3 SD_CMD I/O WLAN SDIO Command Line. 4 GND I Common Ground. 5 SD_D0 I/O WLAN SDIO Data Line 0. 6 /WL_RESET I WLAN Low asserting reset for WLAN core. 7 SD_D1 I/O WLAN SDIO Data Line 1. 8 SLEEP_CLK I Common Low Power Clock input (32.768kHz). 9 SD_D2 I/O WLAN SDIO Data Line 2. 10 POW_ON I Common Used by PMU to decide whether or not to power down internal BCM4329 regulators. If POW_ON is low, then the regulators will be disabled. 11 /CD O Common Cyberlink On-line Detect. PIN tie to ground. 12 NC No use 13 SD_D3 I/O WLAN SDIO Data Line 3. 14 VIN I Common 3.3V Power Input 15 LED O Common 3.3V Output 16 VIN I Common 3.3V Power Input 17 GND I Common Ground. 18 GND I Common Ground. 19 WL_WAKE_IN I WLAN WLAN device wake-up signal input from host to WLAN. 20 BT_UART_TXD O BT Bluetooth UART serial output .Serial data output for the HCI UART interface. 21 NC No use 22 BT_UART_RXD I BT Bluetooth UART serial input. Serial data input for the HCI UART interface. 23 NC No use 24 BT_UART_RTS O BT Bluetooth UART request to send. Active-low request-to send signal for the HCI UART interface. 25 SW1 I Common Antenna select. SW1 and SW2 are floating, Select antenna 1 SW1=1,SW2=0,Select antenna 1
KF-XXXX-X-XXX-版本 SW1=0,SW2=1,Select antenna 2 26 BT_UART_CTS I BT Bluetooth UART clear to send. Active-low clear-to-send signal for the HCI UART interface. 27 SW2 I Common Antenna select. SW1 and SW2 are floating, Select antenna 1 SW1=1,SW2=0,Select antenna 1 SW1=0,SW2=1,Select antenna 2 28 TYPE O Common Cyberlink type Detect. PIN tie to 3.3V. 29 GND I Common Ground. 30 VIN I Common 3.3V Power Input 31 /BT_RESET I BT Low asserting reset for Bluetooth core. 32 BT_WAKE_IN I BT Bluetooth device wake-up signal input from host to Bluetooth. The polarity of this signal is software configurable and can be asserted high or low. 33 BT_WAKE_OUT O BT Host wake-up signal output from WLAN to host. 34 GND I Common Ground. 35 NC Tie 10k to ground 36 WL_WAKE_OUT O WLAN Host wake-up signal output from WLAN to host. 37 BT_PCM_CLK I/O BT PCM clock, can be master (output) or slave (input). 38 NC Reserved for MIMO 39 BT_PCM_SYNC I/O BT PCM sync signal, can be master (output) or slave (input). 40 GND I Common Ground. 41 BT_PCM_OUT I BT PCM data input. 42 NC No use 43 BT_PCM_IN O BT PCM data output. 44 NC Reserved for MIMO 45 NC No use 46 NC Reserved for MIMO 47 NC No use 48 NC No use 49 WL_TXD O WLAN TX pin of debug UART 50 NC No use
KF-XXXX-X-XXX-版本 51 WL_RXD I WLAN RX pin of debug UART 52 NC No use 1.7.2 Power On Sequence 1.7.2.1 Power On Sequence 1 Figure 2 Power On Sequence 1 1.7.2.2 Power On Sequence 2 Figure 3 Power On Sequence 2 1.7.2.3 Power On Sequence 3VINVINVINVIN VINVINVINVIN
KF-XXXX-X-XXX-版本 Figure 4 Power On Sequence 3 1.7.3 Interface 1.7.3.1 External Clock Reference (SLEEP_CLK) Table 7 External Clock Reference Parameter Description Remarks Nominal input frequency 32.768 KHz Frequency accuracy +/-200 ppm Duty cycle 30-70 % Input signal amplitude 200 to 1800 mVp-p 200-1800 mVp-p to avoid additional current consumption. 3.3Vp-p maximum. Signal type Square-wave or sine-wave Input impedance 100KΩ；< 5 pF when power is applied or power is off Clock jitter (integrated over 300Hz – 15kHz) <1 Hz 1.7.3.2 Input/Output DC Terminal Characteristics Table 8 Input/Output DC Terminal Characteristics Digital Terminals Min Typ Max Unit VIL input logic level low - - 0.8 V Input Voltage VIH input logic level high 2.0 - - V VINVINVINVIN VINVINVINVIN
KF-XXXX-X-XXX-版本 VOL output logic level low (100μA load) - - 0.4 V Output Voltage VOH output logic level high (-100μA load) 2.4 - - V IIL input logic level low - 0.3 - uA Input Current: IIH input logic level high - 0.3 - uA IOL output logic level low (VOL =0.4V) - - 3.0 mA Output Current IOH output logic level high (VOH =2.9V) - - 3.0 mA Input Capacitance :CIN - - 5 pF 1.7.3.3 WLAN SDIO Timing 1.7.3.3.1 Default Mode Figure 5 WLAN SDIO Timing, Default Mode Table 9 WLAN SDIO Timing, Default Mode Parameter Symbol Min Typ Max Unit Frequency-Data Transfer Mode fPP 0 - 25 MHz Frequency-Identification Mode fOD 0 - 400- KHz Clock Low Time tWL 10 - - ns Clock High Time tWH 10 - - ns Clock Rise Time tTLH - - 10 ns Clock CLK (All values are referred to min. VIH and max. VIL) Min (Vih) = 0.7*VIN and max (Vil) = 0.2*VIN Clock Falling Time tTHL - - 10 ns Inputs: CMD, DAT Input Setup Time tISU 5 - - ns
KF-XXXX-X-XXX-版本 (referenced to CLK) Input Hold Time tIH 5 - - ns Output Delay time-Data Transfer Mode tODLY - - 14 ns Outputs: CMD, DAT (referenced to CLK) Output Delay time-Identification Mode tODLY - - 50 ns Remark: Timing is based on CL < 40pF load on CMD and Data. 1.7.3.3.2 High Speed Mode Figure 6 WLAN SDIO Timing, High Speed Mode Table 10 WLAN SDIO Timing, High Speed Mode Parameter Symbol Min Typ Max Unit Frequency-Data Transfer Mode fPP 0 - 50 MHz Frequency-Identification Mode fOD 0 - 400- KHz Clock Low Time tWL 7 - - ns Clock High Time tWH 7 - - ns Clock Rise Time tTLH - - 3 ns Clock CLK (All values are referred to min. VIH and max. VIL) Min (Vih) = 0.7*VIN and max (Vil) = 0.2*VIN Clock Falling Time tTHL - - 3 ns Input Setup Time tISU 6 - - ns Inputs: CMD, DAT (referenced to CLK) Input Hold Time tIH 2 - - ns Outputs: CMD, DAT Output Delay time-Data tODLY - - 14 ns
KF-XXXX-X-XXX-版本 Transfer Mode Output Hold time tOH - - 50 ns (referenced to CLK) Total System Capacitance (each line) CL - - 40 pF Remark: Timing is based on CL < 40pF load on CMD and Data. 1.7.4 Mechanical This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not causeinterference, and (2) this device must accept any interference, including interferencethat may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditionssuivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur del'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage estsusceptible d'en compromettre le fonctionnement.The distance between user and products should be no less than 20cmLa distance entre l'utilisateur et de produits ne devrait pas être inférieure à 20cmThe host device must be labelled to display the IC ID of the module "Contains IC:9726A-WM1010BGN10"
KF-XXXX-X-XXX-版本 Appendix A FCC A.1 FCC statement in User's Manual (for class B) "Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. A.2 FCC Statements: 1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:  This device may not cause harmful interference,  and This device must accept any interference received, including interference that may cause undesired operation. 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 4. This compliance to FCC radiation exposure limits for an uncontrolled environment, the minimum of 20 cm separation distance shall be maintained between antenna and body. The host device must be labelled to display the FCC ID of the module "ContainsFCC ID: ZLZWM1010BGN10"

Navigation menu