Mintek LV To The Manual 01de25a3 51ce 466c B32d 89f5e48cf66c

User Manual: Mintek LV to the manual

Open the PDF directly: View PDF PDF.
Page Count: 30

DownloadMintek LV  To The Manual 01de25a3-51ce-466c-b32d-89f5e48cf66c
Open PDF In BrowserView PDF
INSTALLATION AND
OPERATION INSTRUCTIONS
Brentwood™ LV
EPA Wood-Burning Fireplaces
P/N 506023-13 REV. A 02/2011

TM

MODEL
Brentwood LV
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and
understand these instructions before beginning your installation.
Shown with louver kit installed

Shown with clean face kit installed

THIS UNIT REQUIRES THE INSTALLATION OF A
FINISHING KIT. SEE “PARTS REQUIRED”
SECTION FOR DETAILS

Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of the fireplace system, including
but not limited to the fireplace, chimney components and accessories,
may void the warranty, listings and approvals of this system and could
result in an unsafe and potentially dangerous installation.
Lennox Hearth Products wood-burning fireplaces are designed for use
as a supplemental heater. They are not intended for continuous use
as a primary heat source.

Fireplace, Also For Use In
Manufactured Homes With Solid Fuel Only.

SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE

WARNINGS

WARNINGS
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
• If small children are present in the home, it is
recommended that this appliance be fitted with
an adjustable safety gate or barrier screen.

• The fireplace cannot be operated without a door.
Consult your dealer to select the correct door.
• Important! To assure proper alignment of glass
doors: Install this fireplace in a square and
plumb condition, using shims as necessary at
sides and/or bottom.
• Install the fireplace only as described in these
instructions.

Listed to standards:
ULC-S610 & UL-127
Report No. 3011202
EPA Cert. No. 537

PIBRENTLV REV. 1 02/2011

IMPORTANT! GENERAL SAFETY
PRECAUTIONS. READ AND
UNDERSTAND THESE SAFETY
RULES BEFORE YOUR FIRST FIRE.

WARNING
THE FIREPLACE MUST BE OPERATED WITH THE DOOR FULLY
OPENED OR DOOR FULLY CLOSED.
IF THE DOORS ARE LEFT PARTLY
OPENED, GAS AND FLAME MAY BE
DRAWN OUT OF THE FIREPLACE
OPENING, CREATING RISKS OF
BOTH FIRE AND SMOKE.

WARNING
NEVER use gasoline, gasolinetype lantern fuel, kerosene,
charcoal lighter fluid, naphtha,
engine oil or similar liquids to
start or “freshen up” a fire in this
fireplace. Keep any flammable
liquids a safe distance from the
fireplace at all times.

WARNING
THIS FIREPLACE HAS NOT BEEN
TESTED WITH AN UNVENTED
GAS LOGS OR A FIREPLACE
INSERT. TO REDUCE RISK
OF FIRE OR INJURY, DO NOT
INSTALL AN UNVENTED GAS
LOG SET OR FIREPLACE INSERT
OR OTHER PRODUCTS NOT
SPECIFIED FOR USE WITH THIS
FIREPLACE.

WARNING
Never leave your fireplace unattended while it is burning.

WARNING
To avoid the risk of damaging
fireplace materials and increasing the risk of fire, do not use the
fireplace to cook or warm food.
2

WARNING
Use care when selecting window
treatments for windows located
near the fireplace. Avoid using
combustible flowing window
treatments such as curtains on
nearby windows that are of sufficient length to be blown in front
of an open flame when the window
is opened. Keep any combustible
furniture, materials or decorative
pillows at least 48" (1219 mm)
from the front fireplace opening.

WARNING
Never modify or alter your fireplace
system in any way. To do so may
create a potential fire hazard and
void the limited warranty, listings
and approvals of this system.

IMPORTANT
When burning wood, use SOLID
NATURAL DRY WELL-SEASONED
WOOD ONLY. Hardwoods are recommended (soft woods tend to burn
very quickly).
• DO NOT burn treated wood,
charcoal, coal, trash, cardboard,
driftwood, woods dipped in tar,
Christmas tree greens, pitch, pine
tar, creosote, chemical chimney
cleaners, flame colorants, polystyrene packaging, wood products with synthetic binders (i.e.
plywood). Plywood, lumber and
other misc. materials can produce
abnormally high temperatures,
sputtering and smoking fires and
may contain hazardous chemicals
to treat insects and fungus.
• Burning unapproved fuels can
produce excessive temperatures,
beyond the design capabilities
of the fireplace and may produce
excess sparks or may contain
hazardous chemicals. Burning
unapproved fuels can result in
a chimney fire, a house fire,
personal injury, death or loss of
property.

WARNING
Never leave children unattended
when there is a fire burning in the
fireplace.

WARNING
Always ensure that the air inlet to
the fireplace is free from debris
and any other obstructions that
can block the entrance of air.

IMPORTANT
WHEN INSTALLED IN A MOBILE OR
MANUFACTURED HOME:
• Mobile or manufactured home
installations must be installed in
accordance with the requirements
of the Department of Housing and
Urban Development (HUD) “Mobile
Home Construction and Safety standards” for US or Canada Mortgage
and Housing Corporation (CMHC)
for Canada.
• The fireplace must be fastened to
the floor by unfolding and screwing
the small tabs on both sides at the
bottom of the fireplace.
• It is necessary to have access
openings, for inspection purpose
only, into built-in enclosures surrounding the fireplace installation.
Such openings to require a household tool for access.
• The vapor barrier of the mobile
home shall be as close as possible
of the location where the chimney
assembly penetrates the ceiling
and roof structure with no interference to the required clearance to
combustible material.
• When the mobile or manufactured
home has a flat roof, the Attic Radiation Shield must be installed from
below going through the roof (See
Figures 29b and 29d).
• Warning: Do not install in a
sleeping room

WARNING
Neither the manufacturer nor the
seller warrants “smoke free”
operation nor are we responsible for inadequate system draft
caused by mechanical systems,
general construction conditions,
inadequate chimney heights,
adverse wind conditions and/or
unusual environmental factors or
conditions beyond our control.

Congratulations!

Parts Required

When you purchased your new wood fireplace, you joined the ranks of thousands of
individuals whose answer to their home heating needs reflects their concern for aesthetics,
efficiency and our environment. We extend our continued support to help you achieve
the maximum benefit and enjoyment available from your new wood fireplace.

Fireplace Model Brentwood LV

Thank you for selecting a Lennox Hearth Products wood fireplace as the answer to your
home supplemental heating needs.
TABLE OF CONTENTS
SAFETY RULES and Specifications for
Mobile or Manufactured
Home Installation..........................Page
Introduction.......................................Page
Parts Required ..................................Page
Optional Equipment............................Page
Operating The Fireplace.....................Page
Fuel....................................................Page
Combustion Control . ........................Page
Refueling For Best Performance........Page
Smoking – Causes And
Troubleshooting.............................Page
Important Cautions............................Page
Maintaining Your
Brentwood™ LV Fireplace.............Page
Chimney Maintenance........................Page
Dealing With A Chimney Fire..............Page
Finish Door Casing Care.....................Page
Disposing of Ashes............................Page
Refractory Installation........................Page
Door Installation................................Page
Door Adjustment................................Page
Glass Care - Replacement..................Page
Glass Care - Cleaning.........................Page
Gasket Replacement .........................Page
Fireplace Installation .........................Page
Locating The Brentwood LV Fireplace...Page
Installing The Finishing Kits...............Page
Framing, Facing And Mantel...............Page
Hearth Extension Requirements . ......Page
Cold Climate Installations...................Page
Fireplace and Framing Dimensions....Page
Insulated Chase Construction............Page
Nailing Flanges...................................Page
Facing / Mantel...................................Page
Hot Air Ducting Installation ...............Page
Gravity Kit..........................................Page
Central Forced Air Kit.........................Page
Outside Air Kit . .................................Page
Chimney System................................Page
Chimney Installation Notes................Page
Chimney Installation Instructions.......Page
Offset Chimney Installation................Page
Angled Wall Radiation Shield.............Page
Chimney Support Installation.............Page
Chimney Chase And
Multiple Terminations......................Page
Chimney Adaptor...............................Page
Masonry Application Instructions......Page
Installation Accessories.....................Page
Chimney Components Lists...............Page
Specifications.....................................Page
Clearances.........................................Page
Replacement Parts.............................Page
Product Reference Information..........Page

THE FIREPLACE
INTRODUCTION
2
3
3
3
4
4
4
5
5
5
6
6
6
6
6
7
7
7
8
8
8
8
8
9
10
10
10
11
12
12
13
14
14
15
16
17
17
18
19
21
22
22
22
23
24
25
27
27
28
30

The Brentwood LV wood-burning fireplace is
an energy efficient, heat circulating, closed
combustion fireplace. You will receive a lifetime
of comfort and enjoyment from your fireplace
provided it is installed, maintained and operated properly.

• ..Finishing Kit - Required *
...(Order Separately)
- Louver kit
OR
- Clean face obstruction plate kit. Must be
used in conjunction with a gravity vent kit.
*SEE “INSTALLING THE FINISHING KITS”
SECTION FOR THE ASSEMBLY OF THE FINISHING KITS.
• ..Black steel door - Required
...(included w/fireplace)
• ..Outside air kit - Required
...(included w/fireplace)

• Please read these instructions and retain

• 	� Blower kit with thermo-disc
	�� (included w/fireplace)

• Before beginning the fireplace installation,

• .6” diameter chimney - model ASHT+,
S-2100+, HT6000+, HT6103+ or AC manufactured by Security Chimneys International
only, including:
- Chimney lengths
- Elbows (where necessary)
- Associated components as per these
		 installation instructions

this manual for future reference.

consult the local authorities to obtain your
building permit and check your local building
codes. Install the fireplace only as described
in these instructions and using only Lennox
Hearth Products components.

• This fireplace has been tested for CAN/ULC
S610-M87 and ANSI/UL 127 under report
number 3011202. It has also been tested
for EPA 40 C.F.R Part 60, section 60.532(b).
Certificate number 537.

• The Brentwood LV fireplace is not intended for

use with a gas log set. Do not use a fireplace
insert or any other product with this fireplace
unless it is specified by Lennox Hearth Products
for use with this appliance. Failure to follow
these instructions will void the certification and
the warranty of the fireplace and may result
in an unsafe installation.

OPTIONAL EQUIPMENT
• .Additional Equipment (optional)
-.AC chimney adaptor
		 (required if using AC chimney)
-.AC chimney outside air kit
- Gravity venting system
- Central forced air kit u
- Blower speed control

u Not tested under EPA certification. If installed, this appliance no longer qualifies
for EPA certification.

• Lennox Hearth Products wood fireplaces are
designed for use as a supplemental heater.
They are not intended for continuous use as
a primary heat source.

3

OPERATING THE fireplace
Fuel
USE SOLID NATURAL WOOD FUEL ONLY. The
Brentwood™ LV fireplace is designed to work
best when fueled with dry seasoned natural
wood only. Hardwoods are preferred to softwoods since the energy content of wood is
relative to its density. Hardwoods will result in
a longer burning fire and less frequent refueling.
A moisture content of 15% to 20% (seasoned)
is recommended. Wood that has been cut and
split and let to dry under a cover for a period
of one year will usually meet that criteria. The
required drying time will vary depending on the
climate. Wood that is packed tight together will
take longer to dry. Seasoned wood is darker in
color than wet wood and will have visible cracks
in the grain on the ends. Excessively wet wood
will be difficult to burn and will result in lower
efficiency, increased creosoting and deposits on
the glass and in the chimney. Excessively dry
wood will burn well but will also have higher
emissions and shorter burning time.
Do not burn scrap or garbage, treated wood or
wood such as driftwood from the ocean which
has been exposed to salt or other chemicals.
Salt or chemicals can corrode the firebox and
chimney. Do not burn large amounts of paper,
cardboard, Christmas tree branches or building
construction materials. Intense firing with these
materials may overheat the fireplace, causing
damage to the unit, a fire or even possibly igniting a chimney fire if the chimney is creosoted.
Burning unapproved fuel, resulting in excessive
pollutants being emitted, may be prohibited and
subject to a fine or other penalty by the authority
having jurisdiction in your area.
Processed firelogs can be used. Although, do
not poke or stir the logs while they are burning.
Use only firelogs that have been evaluated for
the application of fireplace and refer to firelog
warnings and caution markings on packaging
prior to use.
First Fires
Before using the fireplace make sure to remove
the plastic wrapping and EPA label on door.
Remove any glue residue left by the label
using mild soap.

4

The first five or six fires should be small fires
of short duration (about 30 to 60 minutes).
This will help cure the refractory bricks. During
the first few fires of this appliance there may
be some odor and smoke due to the curing of
the paint, dust accumulation and burning off of
lubricants used in the manufacturing process. It
may set off a smoke alarm located in the same
room. For this reason the room should be well
ventilated for the first few fires.

WARNING
Be careful adding wood fuel to the
fire or handling fireplace tools such
as shovels, tongs or pokers.

WARNING
The bottom refractory can be
cracked by excessive abuse such
as tossing heavy logs onto the
grate or gouging with fireplace
tools. Exercise caution when
adding wood to your fireplace.
Building a Fire
(starting and maintaining a fire)
To start a fire, place several crumpled up balls of
newspaper in the firebox. Place small dry pieces
of kindling on top of the paper, criss-crossing
the kindling so that there are air spaces in between. Keep the fuel far back enough so that air
can get underneath. Open the air controls fully
and light the newspaper. Once the newspaper
and the kindling is well ignited, close the door.
Once the kindling fire is well established, cord
wood can be added (see Primary Air Combustion Control section for proper operation of the
air controls).

COMBUSTION CONTROLS
Primary Air and Air Boost Controls

There is no flue damper in the Brentwood LV
fireplace. As is common with air tight stoves,
the combustion air control sets the flow of air
entering the firebox. This allows for a more
precise control of the fire. The combustion air
control is located below the door on the left side.
The main source of air (primary air) entering
the firebox can be diminished by moving the
air combustion control from left to right. The
primary air is fully opened when the air control
is completely moved to the left. The air control
device can also be used to add an extra boost of
air especially during fire start up and reloading
of the unit. Pulling the air combustion control
will induce an air boost at the base of the fire
allowing an easier fire start up. When the fire is
well established, the control can be pushed in
to shut down the air boost allowing for a longer
burn time. The combustion air control should
be in the closed position (primary air and air
boost) when the fireplace is not in use. This
will minimize air leakage up the chimney. The
combustion air control should be opened before
opening the door to minimize the possibility of
back draft coming into the room.

Accelerated Combustion
The maximum heat output for the Brentwood
LV fireplace is achieved by burning with the
door closed and the combustion air opened
and pulled out. By this method, the Brentwood
LV fireplace can produce up to 55,000 BTU of
heat per hour. However, it will be necessary
to reload with wood every one or two hours.
This is the least efficient method of burning the
Brentwood LV fireplace.

Push to Close
Air Boost

The unit will burn best with 2-3 pieces of cord
wood spaced 1 to 2 inches apart and allowing
air to get under the fuel. Criss-crossing or arranging the fuel so that air can get underneath,
will help the fire to get started easily. The unit
should be operated with the air control fully open
long enough to get the cord wood well ignited.

Slow

Medium
Accelerated

Figure 1

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Pull to
Open
Air Boost

Use caution when firing with the combustion
air control wide open. Only burn cord wood
in this manner. Small dry pieces of softwood
and construction scraps will burn very intensely
using this method and may damage the firebox.
Medium Combustion
This is the recommended mode of operating
the Brentwood™ LV fireplace and should be
the one normally used since it will deposit the
least amount of creosote on the glass and in
the chimney. The combustion air control must
be 3/4 closed (Figure 1) and pushed in to close
the air boost. The precise setting will depend
on many factors, including chimney length and
the moisture content of the wood.
For instance, a long chimney will necessitate
closing the damper more. To obtain the proper
combustion, close the damper completely, then
open it about 1/4” to 1/2”. Three medium size
pieces of wood should be burning on a bed of
hot coals. The heat output will be approximately
30,000 BTU per hour and the loading time will
be about every 3-4 hours. Softwoods may be
burned using this method but the time will be
substantially reduced.
Slow Combustion
When the air combustion control is completely
closed, the fireplace is in a slow combustion
phase. If the hearth is hot enough, slow combustion will not extinguish the fire, but there will be
a noticeable change in the flame pattern. The
flames will be slow and may appear dirty if the
wood is too wet (moisture content of 20% and
more). Do not allow the wood to burn without
flame, since this will produce excessive creosote
in the unit.
Creosote may accumulate on the glass door. This
method of burning should be used only after
operating the Brentwood LV fireplace with the
air control opened (Figure 1) to produce a hot
fire for about an hour or at medium pace for at
least three (3) hours. Slow combustion can be
used at night in order to reduce the heat output
and to prolong the burn. The loading time will
be between 6-8 hours.

REFUELING FOR BEST PERFORMANCE
The Brentwood LV fireplace will operate best if
attention is given to operating the unit with the
damper fully opened (figure 1) after refueling
in order to bring the firebox and the chimney
system up to their optimum operating temperature. Combustion efficiency is relative to firebox
temperature. A temperature of 932º F (500º C)
and up, with a visible flame, in the upper part
of the firebox indicates a maximum efficiency.
To obtain this temperature, the fireplace must
be operated with the primary air and air boost
controls fully opened during 10 to 20 minutes
after reloading, depending on the heat and on
the moisture content of the wood.
Once you have reached the desired temperature,
the air boost can be closed and the primary air
set to a medium setting. You know you have
reached the desired temperature when, closing
the primary air control, you can see a flame
at the top of the firebox. The benefit of this
technique will be cleaner glass, less creosoting,
greater efficiency and the most pleasing fire for
your enjoyment. If your fireplace is equipped
with a forced air system, make sure the central
blower is turned off during reloading to avoid
smoking problems.

SMOKING –
CAUSES AND TROUBLESHOOTING
To reduce the likelihood of smoking when opening the door, set the combustion air controls to
the left before opening the door. Your fireplace
has been designed and tested to provide smoke
free operation. Occasionally, there may be a
small amount of smoking upon lighting the fire,
until the chimney heats up but this should not
continue. If the fireplace continues to smoke
it is probably for one of the following reasons:
A. Negative pressure in the house As the fire burns, air goes up the chimney.
This air must be replaced through leakage
into the house or through the outside air duct.
When operating the Brentwood LV fireplace,
open a nearby window temporarily to check
if there is adequate replacement air supply.
B. Blowers operating (e.g.: range hood) These blowers draw air out of the house
and may actually cause a negative pressure
in the house. Turn off all blowers and open
a nearby window to determine if this is the
cause of the problem.

C. Wet wood - Wet or tarred wood will smoulder
and smoke instead of burning properly. Your
dealer can help you determine if you have
properly seasoned wood for burning.
D. Dirty or blocked chimney - Check to make
sure the chimney is clear and clean. If dirty
call a certified chimney sweep or use a
properly sized chimney brush to clean.
E. Chimney not long enough - The minimum
chimney height is twelve (12) feet (3.7 m) not
including the fireplace height. The chimney
must extend at least three (3) feet (915 mm)
above its point of contact with the roof and
at least two (2) feet (610 mm) higher than
any roof or wall within ten (10) feet (3 m) of
it. When installed with offsets, the minimum
chimney height is fifteen (15) feet. Additional
height will increase draft and will decrease
the tendency to smoke.
F. Poor chimney draft - With no fire, there should
be sufficient draft to exhaust cigarette smoke
introduced under the baffle. Chimneys installed
against an outside wall without protection may
generate back draft problems which will cause
start-up problems. To prevent this, open a
nearby window, roll up a piece of paper and
light it. Then, hold it in the upper part of the
firebox to warm up the chimney. Wait until
the draft is sufficient, then start the fire.
G. Blower for forced air kit operating - Make
sure that the blower is in the “off” position
when you open the fireplace door for reloading.

IMPORTANT CAUTIONS

A. Do not block the hot air vents to the fireplace
as this will cause the fireplace to overheat.
B. Never use gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter fluid, or
similar liquids to start or ‘freshen up’ a fire
in this fireplace. Keep all such liquids well
away from the fireplace while it is in use.
C. Do not burn coal. The sulphur in coal will
corrode the firebox.
D. Do not burn driftwood which has been in the
ocean or salt water. The salt will corrode
the firebox and chimney.
E. Do not burn wood in the area in front of the
grate.
F. Do not abuse the unit by burning paper, or
cardboard or construction material such as
pressed wood, plywood or lumber. Wood
protectors, metallic paper, coal, plastic,
waste, sulphur and/or oil will damage the
fireplace.
G. Do not allow the wood to smoulder or burn
without flame, since this will produce
excessive creosote in the unit as well as
increased particulate emissions.

5

MAINTAINING YOUR BRENTWOOD™ LV
FIREPLACE

Top Baffle Removal Prior to Cleaning The
Chimney

Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar
and other organic vapors, which combine
with expelled moisture to form creosote. The
creosote vapors condense in the relatively cool
chimney flue of a slow-burning fire.

Before starting to clean your chimney, we
recommend that you remove the top baffle to
avoid creosote dust collection at the top of the
baffle. Follow these steps to set the top baffle
out of the way:

As a result, creosote residue accumulates on the
flue lining. When ignited this creosote makes
an extremely hot fire.
The chimney shall be inspected at least twice
a year during the heating season to determine
when a creosote buildup has occurred.

1. Remove the side refractory holder. They are
located at the top of the refractory.
2. Lift the front baffle.
3. Slide the back baffle under the front baffle.
You now have access to the chimney.

When creosote has accumulated it shall be
removed to reduce the risk of a chimney fire.
When the creosote accumulation is large, a
creosote fire in the chimney can damage the
chimney and overheat the surrounding wood
framing. Creosote formation in a chimney can
be minimized by making sure there is always
visible flame burning, avoid smouldering fires
and by proper refuelling techniques.
Chimney Maintenance

Regular chimney maintenance and inspection
can prevent chimney fires. If you have a chimney
fire, follow these steps:
1. Close the fireplace door and the combustion
air controls.
2. Alert your family of the possible danger.
3. If you require assistance, alert your fire
department.
4. If possible, use a dry chemical fire extinguisher, baking soda or sand to control the
fire. Do not use water as it may cause a
dangerous steam explosion.
5. Check outside to ensure that sparks and hot
embers coming out of the chimney are not
igniting the roof.
6. Do not use the fireplace again until your
chimney and fireplace have been inspected
by a qualified chimney sweep or a Fire
Department Inspector.

Finish Door Casing Care
Use a glass cleaner and a soft cloth to polish
the casing. Do not use abrasives such as steel
wool, steel pads or an abrasive polish for they
may scratch the casing’s finish.

Figure 2a - Top Baffle Removal

DISPOSING OF ASHES

Regular chimney inspection and maintenance
combined with proper operation will prevent
chimney fires. Keep your chimney clean. Do not
allow more than 1/16” (1.6 mm) creosote build
up in your chimney. The amount of creosote
will depend on variables such as frequency of
use and type of fire. We recommend that you:

Remove ashes only when the fire is out and the
ashes are cold (24 to 48 hours after the fire is
out). Do not leave the ashes in the house as they
give off carbon monoxide and other toxic gases.

A. Initially inspect the chimney system weekly.
From this, you will learn how often it will be
necessary to clean your chimney.

Disposal of Ashes: Ashes should
be placed in a metal container with
a tight fitting lid. The closed container of ashes should be placed
on a non-combustible floor or on
the ground well away from all
combustible materials, pending
final disposal. If the ashes are
disposed of by burial in soil or
otherwise locally dispersed, they
should be retained in the closed
container until all cinders have
thoroughly cooled.

B. Have your chimney cleaned by a qualified
chimney sweep. If you wish to clean it
yourself, we recommend using a stiff plastic
or non-metallic brush. If a metal brush is
used, its size should be slightly smaller than
the flue to avoid damaging the chimney. Do
not use a brush that will scratch the stainless
steel interior of the chimney.

WARNING

Figure 2b - Top Baffle Removal

C. Do not expect chemical cleaners to keep
your chimney clean. The rain cap can be
removed for inspection and/or cleaning of
the chimney.

6

Dealing With a Chimney Fire

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

REFRACTORY REPLACEMENT
The intense heat of the fire will normally cause
hairline cracks in the refractory. These cracks
can be minimized by proper curing as described
in “First Fires”. They will not normally diminish the effectiveness of the refractory. If large
cracks develop, then the refractory should be
replaced. To replace the refractory bricks, follow these steps:
1. Remove the front refractories
2. Remove the bottom refractory
3. Remove the left side refractory
4. Remove the right side refractory
5. Remove the back refractory
6. Remove the front ceramic baffle
7. Remove the rear ceramic baffle
To install the new refractories, follow the above
steps in reverse.

DOOR INSTALLATION
Your fireplaces door has been factory installed
and adjusted.
To remove the door simply unscrew the top
hinge from the door then lift the door (without
touching the trim over the door) to disengage
the male part of the bottom hinge from the
female part.
The door adjustment has been set at the factory.
If the fit is still not perfect, you can adjust the
door using the hinge screws.

DOOR ADJUSTMENT
The door may need to be adjusted to be completely airtight. The gaskets’ air-tightness can be
adjusted using the adjustment screw located on
the right side of the fireplace facade (An Allen
key #1/8 – not supplied - will be necessary for
this adjustment).
Checking Door Seal - A one-inch strip of paper
may be used to perform a test of the integrity
of the door seal. Close the door on the paper in
at least eight points. It is normal to feel only a
slight amount of friction. The door gasket does
not need to be “tight” in all areas, since a small
amount of leakage is not hazardous or detrimental to the performance of your fireplace.

7

6

5
4

1. Front Refractories
2. Bottom Refractory
3. Left Side Refractory
4. Right Side Refractory
5. Back Refractory
6. Front Ceramic Baffle
7. Rear Ceramic Baffle

Figure 4

3
2

1

WARNINGS
• Use only a Lennox Hearth Products glass doors, specifically designed
for the Brentwood™ LV fireplace.
• The fireplace cannot be operated without door. Consult your dealer to
select the correct replacement door.
• Important! To assure proper alignment of glass doors: Install this
fireplace in a square and plumb condition, using shims as necessary at sides and/or bottom.

Hinge Screws

Gasket Adjustment
Screw

Figure 5
Figure 3 - Door Installation
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

7

Glass Care

Gasket Replacement

Glass Replacement

The glass used for the Brentwood™ LV fireplace
is a high temperature ceramic glass (1,400° F /
760° C). If the glass breaks, it must be replaced
with an identical ceramic glass. Tempered glass
or ordinary glass will not withstand the high
temperatures of the Brentwood LV fireplace.
Replacement glass should be purchased from
a Lennox Hearth Products dealer (see “Replacement Parts”, Page 28). DO NOT OPERATE THE
UNIT WITH CRACKED OR BROKEN GLASS.

Glass Cleaning

The Brentwood LV fireplace is designed to
keep the glass clean under normal operating
conditions. If the Brentwood LV fireplace is
operated continuously with the combustion air
controls closed, the glass will tend to get dirty
unless the fuel, firebox and glass are maintained
at hot temperatures (see “Refueling For Best
Performance”). To clean the glass, there are a
number of specially designed cleaners. Your
authorized Lennox Hearth Products dealer can
recommend a suitable cleaner which is available
in your area. Regular household glass cleaners
will not clean creosote. Do not use abrasives
such as steel pads, steel wool or oven cleaner
as they will scratch the glass.
DO NOT USE CHEMICAL GLASS CLEANERS
ON PAINTED SURFACES AS IT MAY CAUSE
THE PAINT TO PEEL.
CAUTION : DO NOT ALLOW WINDOW CLEANER
TO GET IN CONTACT WITH DOOR OR PAINT
ON FACADE OR DOOR. ONCE CLOSED,
CONTACT OF GLASS CLEANER WITH THE
FIREPLACE FACADE CAN PROVOKE PAINT
PEELING OFF.

Remove the door from the unit (see Page 7)
and lay it on a clean unabrasive surface. To
replace the gasket, first remove all of the old
gasket and gasket cement. Make sure that the
surface is totally clean before applying new
cement (a high temperature silicone caulking
rated at 500° F [260° C] is suitable) or adhesion
problems may result. Apply gasket cement to
the gasket channel and install the new gasket.
This replacement part is available from your
Lennox Hearth Products dealer in the following
dimensions:
Gasket

Length*

Dimensions

Part No.

Around
Glass

74
(1880)

3/16” x 1”
(4.8 x 25.4)

SR1685J

On Door
Frame

77-3/4
(1975)

5/8 dia.
(15.9)

SR1823G

Table 1

* Inches (millimeters)

FIREPLACE INSTALLATION
Locating The Brentwood LV Fireplace
The best location to install your fireplace is
determined by considering the location of
windows, doors, and the traffic flow in the room
where the fireplace is located, allowing space
in front of the unit for the hearth extension and
the mantel, and taking into consideration the
location of the hot air ducts (optional), outside
air kit and chimney.

If possible, you should choose a location where
the chimney will pass through the house without
cutting floor or roof joists (see fireplace dimensions Page 11).
Usually, no additional floor support is needed
for the fireplace. The adequacy of the floor
can be checked by first estimating the weight
of the fireplace system. Weights are given in
the appendix. Note the floor construction and
consult your local building code to determine
if additional support is needed.
The Brentwood LV fireplace may be installed
directly on the floor or on a raised base (for
proper guidelines, refer to “Hearth Extension
Requirements”) and a minimum of 6’8” (2 m)
measured from the base of the appliance to the
ceiling is required.
When selecting the location, the chimney outlet
position and the direction of the wind are important factor affecting the chimney performance.
To allow a maximum draft and to reduce wind
turbulence, the chimney must:
• Penetrate the highest part of the roof.
• Be installed as far as possible of roof offsets,
trees or any other obstructions that may
cause wind turbulence and back drafts in
the chimney.
• The least amount of offsets (elbows) possible. Note: A maximum of 2 offsets is
allowed.

Location Recommended
Marginal Location
Wind Direction

Location
Not
Recommended

Location
Not
Recommended

Outside Air Intake
Facing the Wind

8

Figure 6

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INSTALLING THE FINISHING KITS
The Brentwood™ LV requires the installation
of a finishing kit. Two options are available:
1. Louver kit (part number: LOUVRECF)
OR
2. Clean face kit (part number: CAPPINGCF)

Installing The Louver Kit
The louver kit includes two identical louver
assemblies. The louvers must be oriented so
the angular parts of the grills are towards the
front and the bottom and the cotter pins are
at the bottom.
Insert the top of the louver rods in the top trims
holes. Than insert the bottom of the rods in the
holes at the bottom of the opening. The cotter
pins will rest on the bottom trim in order to
vertically locate the louvers.

The gravity kit MUST BE used with the
clean face kit to allow hot air flow that
would normally come out of the top louver.
ANY OTHER INSTALLATION MAY RESULT
IN THE FIREPLACE OVERHEATING AND
POTENTIALLY CAUSE A FIRE.

3.
4.

See Gravity Kit section on Page 14 to install
the gravity vent kit.

Installation Steps:
1. Install the side finishing trim, making sure
to differentiate the left from the right. The
shortest end bend should be towards the
bottom.
2. Install the right side trim. The full length flat
part must rest against the right side face
frame, the center bend must be oriented
towards the outside of the unit and the
bends towards the inside. The end bend on
top must be pushed between the crossing

5.
6.

trim and the right side frame. This can be
difficult because these are close together to
allow a good look when using the louver kit.
The part will be fixed in place when installing
the other parts.
Repeat with the left trim.
Install the top obstruction plate in the top
opening, oriented so the insulation faces the
inside and the 1/2 inch bend is towards the
outside and the bottom. The part is pressure
installed to keep from using screws that could
interfere with your finishing material. Place
the bottom bend on the lower trim and push
on it to insert the top bend. Push on the part
so the ends lie well on the fireplace face.
Install the bottom part the same way. Make
sure to push the part to the bottom to leave
the required air space.
(Optional) You can use rivets or sheet metal
screws on all four (4) corners to secure the
installation.

Fireplace Face

2

1

3
2

Figure 7

Installing The Clean Face Kit
The clean face kit includes four parts. Two
trims, left and right, are used to cover the edge
of the finishing material on the sides, and two
obstruction plates to cover the top and bottom
openings allowing to install the finishing material
closer to the door.

WARNING: The bottom obstruction plate
is designed to leave an opening area for
the convection air to circulate and cool
your fireplace. NEVER BLOCK THIS AIR
SPACE TO AVOID OVERHEATING THE
FIREPLACE AND POTENTIALLY CAUSE A
FIRE IN YOUR HOME.

1

1

3

Figure 8

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

9

Framing, Facing And Mantel
The construction of the framing, facing, and
mantel must be in accordance with the standards and the following illustrations (Figures
9, 10 and 11):
A. Frame the fireplace using 2” x 3” or heavier
lumber.

B. WARNING: Combustible materials
cannot be used in the space directly
above the fireplace, except for the
studs above the facade that support
the facing and mantel. This area must
remain empty for a height of 6’8”
(2,032 mm) measured from the base
of the appliance.

C. Frame the fireplace with vertical studs at the
sides of the fireplace running from floor to
ceiling (see Figure 11). If combustible facing
is to be used, position the studs back, from
the front edge of the fireplace (a space that
is the thickness of the facing material, so
that the facing can be installed flush with the
fireplace facing). Frame headers between
the vertical studs only as follows:
• Place 2” x 3” or 2” x 4” headers,
only along the upper part of the front,
side and back faces (some codes
may require a 2” x 6 ” on an outside
bearing wall). Do not put wood or any
combustible material within the area
above the fireplace except on the front
facing.
• Place headers only as required to support
the facing and mantel.

WARNING: THE HEARTH EXTENSION IS TO BE INSTALLED ONLY
AS ILLUSTRATED.

Fireplace

The crack between the fireplace
and the hearth extension must be
sealed with a non-combustible
material such as sand-cement
grout.

Safety Metal Strip
Hearth Extension Non-Combustible
Finish Material
1/2”
13mm
Floor
Fireplace

Elevated Fireplaces

u.Elevated

fireplace installations require a special “Z” Metal Safety Strips
(field provided), in place of the safety
metal strip shown above. The safety
strip should extend the full width of
the fireplace. When more than one
safety strip is used they must overlap
by a minimum of 1”. Hearth extension
of an elevated fireplace must respect
the same minimal dimensions as a
fireplace installed directly on the floor
(Figure 10).

Platform

2”

u

Figure 9 - Hearth Extension Requirements

D. WARNING: The fireplace must not be in
contact with any insulation or loose filling material. Cover the insulation with
Drywall panels around the fireplace.
Hearth Extension Requirements

The Brentwood LV fireplace may be installed
directly on a combustible floor. The supplied
safety metal strip must be positioned as follows:
One half under the front of the fireplace and the
other half must extend on the floor over which
the hearth extension will be built (see Figure 9).

12” Max.
(305mm)
Mantel

Area where wood
Mantel can be
installed

* The safety metal strip must cover the entire
width of the fireplace
The combustible floor in front of the fireplace
must be covered with a non-combustible
material (tile, marble, stone, etc). See Figures
9 and 10.

Cold climate INSTALLATIONS

Climates where temperatures will fall below
32° F (0° C).
The heating performance of the appliance will
vary depending upon the level of insulation,
house design, how the appliance is operated,
etc.
If this fireplace is being installed in a cold
climate, it is especially important to seal all
cracks around the fireplace and wherever cold
air could enter the room with noncombustible
material.
10

45”
(1143mm)
Min.

18”
(457mm)

45 Deg.
4”
(102mm)
Hearth
Extension
36”
(914mm)

17” Min.
(432mm)

Non-Combustible Material

Figure 10 - Hearth Extension Requirements
Also, the outside air inlet duct should be wrapped with noncombustible insulation to minimize
the formation of condensation. Do not place insulation materials directly against the chimney
sections. We recommend that you use the insulated wall radiation shield since it will maintain
the home’s thermal barrier. AC chimney is NOT recommended in very cold climates (in areas with
temperatures below 0°F (-18°C).
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Back Wall of Chase/Enclosure
Including Finising Materials if any

Combustion
Air Kit

Corner Installation

OUTSIDE CHASE

C

L*

21-1/2”

D

J

F
G

H

K

A

FRAMING DIMENSIONS
A

36-1/4”

921 mm

B

40-3/4”

1035 mm

C

28-1/8”

714 mm

D

13-1/4

337 mm

E

76-3/4”

1950 mm

F

38-3/8”

975 mm

G

*25”

635 mm

H

24-1/2”

622 mm

J

54-1/4”

1378 mm

K

8”

203 mm

L

1”

25 mm

20-3/8”

Rough Framing Face (Unfinished Shown)
* Zero Clearance From Back Spacer to Wall

Combustible materials can NOT be used in the space
directly above the fireplace. Do not fill the space
above the fireplace with any material (Except the
wood framing)

E

2” x 3’
Min.

* Total depth is 25-1/2 inches

2” x 3”

including the back spacer
minus 1/2 inch for drywall to
be flush with the facing.

Min.

Plywood 1/2”

7’
Min.
7’
Min.

G
B

Rough Framing Face
(dimension includes finish
material inside framing, if any)

Dimensions with clean face obstruction plate kit installed

10-9/16”

28-1/8"
20-3/16”
25-9/16”

Header

9-1/4"
13-7/8"
24"

22-7/8"

5-3/8”
3-3/8”

1"

10-1/4"

B

1-1/2"

29-5/16”

A
Fireplace Framing

Notes
Diagrams, illustrations and photographs are not to scale – consult
installation instructions. Product
designs, materials, dimensions,
specifications, colors and prices are
subject to change or discontinuance
without notice.
All framing dimensions calculated
for 1/2" dry wall at the fireplace face.
If sheathing the chase or finishing
with other thickness materials,
calculations will need to be made.
* The fireplace must not be in contact
with any insulation or loose filling
material. Cover the insulation with
Drywall panels around the fireplace.

10-1/8"
26-5/8"

13-7/8"

40-3/4"

16-3/8”
12-3/8"

36"

26-5/8"

10-1/8"

14-1/8"
3-3/4"

3-1/2"
24"

Figure 11 - Fireplace and Framing Dimensions

22-3/4"
27-3/4"
36"
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

11

Insulate Joists
Same As Ceiling

Insulated Chase Construction

Storm Collar

Roof Support

Flashing

Attic Radiation
Shield

Draft Stops

Floor
Ceiling
Wall

NOTE: It is recommended that the chase
walls and floor be insulated in the same
manner, using the same insulation, as
the rest of the building, below the attic.

Firestop
CTDT
Termination

• Must have the same firestopping
Note: Nonresistance as adjacent
wall.
Combustible
• Must have the Chase
same insulation as
adjacent ceiling.Flashing
Must Be
Usedregarding
To
• Follow local rules
framing
Cover
construction. Chase

Firestop

Opening

Figure 12

FIREPLACE

7’
(2.1 m)
Min.

6’ 8”
(2 m)
Min.

SEE NOTE
8’8'
(2.4
m)
Level
Level

Drywall or Any Rigid
Material
Insulation
(Thermal Barrier)

2x4

1/2” Plywood

Nailing Flanges
Four nailing flanges are provided to secure the
fireplace to the floor (see Figure 13). Bend
the nailing flanges down so that each flange is
flush with the floor, then using nails or screws,
secure the fireplace to the floor (2 places each
side). The heads of the screws or nails must
be large enough to completely cover the holes
in the nailing flanges.

Fireplace Side

Unbend to floor
and nail/screw

Nailing Flange
(2 places each side)

Figure 13

12

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Solid
Continuous
Surface
Outside
Base

Facing
The facing installation method depends on your
finishing kit choice.
1. Facing with the louver kit - The 2x3 framing
must offset to the back by a distance equivalent to the thickness of your facing material
so the surface of the facing be aligned with
the fireplace face. Combustible materials
must be aligned with the fireplace face and
can not overlay on the fireplace front (black
steel face of the fireplace) (see Figures 14
and 15).
NOTE: Non-combustible materials like brick,
stone or ceramic tiles may be overlayed on the
fireplace front (see Figure 16).

Non-Combustible Facing

Fireplace Frame Section
(Top View)

Drywall
2” X 3” Min.

(51mm x 76mm)

2

1

Spacer

3

Rockboard
or Other

4
1.
2.
3.
4.

Fireplace
Wood frame (2” x 3” Min.)
Drywall
Tiles or Brick

Figure 15

2. Facing with the clean face kit - Must be
used in conjunction with a gravity vent kit.
The 2x3 framing must offset to the back by
a distance equivalent to the thickness of the
drywall.

Figure 17
Non-Combustible Facing
1/2” Drywall

Fireplace Frame Section
(Top View)

2” X 3” Min.

(51mm x 76mm)

Combustible materials must be installed to
be aligned with the fireplace front and can
not overlay on the fireplace front (black steel
face of the fireplace) (see Figures 16 and 17).
Non-combustible materials such as brick,
stone or ceramic tile can project in front of
and onto the fireplace facing up to the tiling
flange on the clean face kit (Figure 19).

Mantel

Spacer

1/2” Drywall

3

4
Do Not
Obstruct
Grill
Door

The mantel must be installed at least 45”
(1143mm) above the base of the fireplace
(Figure 14).

Mantel

2

1

1.
2.
3.
4.

Fireplace
Wood frame (2” x 3” Min.)
Drywall
Tiles or Brick

Figure 18

Figure 16

2” X 3” Min.

Only non-combustible material should be
superposed or projecting over this surface.

(51mm x 76mm)

Spacer

12” Max.
(305mm)
36”
(914mm)

45”
(1143mm)
Min.

36”
(914mm)

Figure 19

Figure 14

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

13

HOT AIR DUCTING INSTALLATION
Different hot air ducting systems can be installed
with the Brentwood™ LV fireplace:
- Gravity kit
- Forced air kit

Gravity Kit

The gravity kit is designed for double hot air
outlets and includes: (See Figures 20 and 21)
- 2 telescopic lengths 8” I.D.
- 2 90º elbows 8” I.D.
- 2 hot air outlet kits (grill and frames)
- 2 adaptors

WARNING: The outlet grills
should not be installed facing upward through a floor.
Danger of burns can result
if grills in floor are stepped
on.

Outlet Grill

See Gravity Kit Accessories on Page 24.

Outlet Grill

10’
(3.1m)
Max.

13” x 13”

(330mm x 330mm)

The only blower that can be used with the gravity
kit is the UZY6.
The gravity kit must be used with the clean face
kit to allow hot air flow that would normally
come out of the top louver. To do so, follow
the steps below:
a) Install the clean face kit making sure that
the insulation strip is installed inside.
b) The fireplace façade can be covered with
non-combustible material (Figure 22).

10’ (3.1m)
Max.

Maintain at least 6-1/2”
(160 mm) clearance from
the outlet grill framing to
a combustible ceiling,
side wall or mantel.

Frame

Figure 21

Grill

Rain Cap

WARNING: Both pipes of
the double hot air outlet
must be installed. Any other installation may cause
fire and void warranty.

Collar
Flashing

Roof Support
Attic Radiation
Shield
Radiation Shield (Firestop)

Figure 20

6-1/2” Min.
(to ceiling)

For safe installation, the gravity kit must meet
the following requirements:
Minimum height*
Maximum length

68” Min.
(1727mm)

68” (1,727 mm)
See Figures 20 and 21

* The height of the louver must be measured
from the base of the Brentwood LV fireplace to
the middle point of the louver.

45” Min.
(1143mm)

u

To extend the double outlet system forward of
the Brentwood LV fireplace (not flush), it will be
necessary to purchase two adjustable lengths
(7B26ZL2A).
When installing the double outlet system, the
hot air outlets can be installed in the same room
as the fireplace, or one or both of the outlets
can be installed in adjacent or upper rooms.
Installing the ducts at different elevations will
tend to exhaust more heat out of the higher
outlet (Figure 21).
14

Non-Combustible
Facing

u
Figure 22
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Combustibles are not allowed below top
spacers above the fireplace. Facing in front
of fireplace must be non-combustible below
this area.

The duct system must be installed respecting
the following:
1. Remove the plates closing up the 8” dia.
holes on top of the fireplace. Then, cut
the insulation and remove the plate under
the insulation in order to obtain two 8” dia.
openings. Fix the adaptors on the fireplace
openings by turning clockwise (Figure 20).
2. Maintain at least a 2” (50 mm) clearance
between the ducts and any combustible
material; the required hole size is 13” x 13”
(330 mm x 330 mm).

Exception #1: For the grills, the framing can be 10-3/4” x 10-3/4” (275 mm
x 275 mm) to provide the clearance as
required by the integral spacers on the
double outlet duct system.
3. The maximum number of elbows in a run
of duct is two.
4. Maintain at least 6-1/2” (160 mm) clearance
from the outlet grill framing to a combustible
ceiling, side wall or mantel.

CENTRAL FORCED AIR KIT (NOT TESTED
UNDER EPA CERTIFICATION)
The knock-outs provided on the back and on
the sides of the Brentwood™ LV fireplace allow
the connection of insulated flexible pipe which
enables you to heat adjacent rooms up
to 50 feet from the fireplace.
The ducting system must be installed as described below:
A) Remove the knock-out and cut the insulation.
In the back, there may be another knock-out
to remove under the insulation.
B) Fix the adaptor at the back and/or the side
of the fireplace by twist-locking the adaptor
to the fireplace. You can use more than one
outlet on the fireplace (Figure 23).
C) Attach the 5” flexible pipe, using the collars
provided. Important: Make sure that the
plastic wrapping around the flexible pipe
will not be in contact with the fireplace using
aluminum tape.

D) .Route the flexible pipe to the chosen location.
The ducting system can be installed either
in an upper room or in a lower room.
E) Attach the flexible pipe to the fan, using the
collars (Figure 24).
F) Fix the back draft damper to the fan outlet.
G) .Attach a flexible pipe to the fan / flexible pipe
adapter (square to round) and stretch it up
to the location where the heat is required.
H) At that point, the flexible pipe can be attached
to any air distribution grill.
I) Install the blower heating and cooling thermostat (HCTW) in that part of the house to
be heated by the hot air duct. The thermostat
can be switched to a cooling thermostat and
installed in the same room as the unit. This
thermostat will turn on the blower when
the room where the fireplace is located
becomes too hot.
This option requires electricity. Make sure that
the connections to the fan have been made
according to the local codes and comply with
their requirements (see instruction provided
with the thermostat).

5. When traversing a combustible wall or floor,
a firestop must be installed at the wall or
floor penetration. The hole size must be
13” X 13” (330 mm x 330 mm).
6. Do not connect the hot air ducts to a central
heating system. Malfunction of the heating
system’s blower will cause the fireplace to
overheat. A furnace duct is only single wall
and not double wall as is required for the
Brentwood™ LV fireplace hot air exhaust.
7. Use only Lennox Hearth Products grills and
components as described in this manual.
Other grills or registers, for example, may be
too restrictive and may overheat the fireplace
or ceiling.

Adaptor
Insulated
Flexible
pipe

8. Do not use insulated flexible ducts as they
will overheat.
9. Do not use tees or any other components
than the ones specifically listed here.
10. Never allow the ducting to pitch down as
hot air will be trapped creating a fire hazard.
Never route the ducting downwards.

Figure 23

11. The hot air outlet grills must be installed with
the louvers pointing downwards in order to
prevent overheating adjacent ceilings.

Insulation

12. Always install the two outlet grills when using
the double hot air outlet kit and blocking the
upper louver of the fireplace.

Blower

Flex 5” Diameter

Aluminium Tape

Tightening Collar

Figure 24
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

15

OUTSIDE AIR KIT - REQUIRED (Included w/fireplace)
During operation, the fireplace requires fresh air for combustion and
draws air out of the house. It may starve other fuel burning appliances
such as gas or oil furnaces. As well, exhaust blowers may compete for
air, causing negative pressure in the house, resulting in smoke entering
the house from the fireplace. This situation is aggravated in modern
airtight houses. To overcome this problem, we strongly recommend that
you install an outside air assembly. Check with local authorities having
jurisdiction in your area, it may be mandatory.

Note: Should you decide not to install the outside air assembly,
proceed as follows:

- Remove the bottom grill. The air box is located on front left and is on
a slant.
- Unscrew the four screws holding the inside air box covering plate and
remove it.

OUTSIDE CONNECTION

Aluminum Tape
Outside
Intake

Plastic Cover

Screw

Opening
Facing
Down

Insulation
Flexible Pipe
Aluminum Tape

Wall

Outside Air Installation
The outside air assembly may be installed according to the following
requirements:
A) Duct length should be kept to a minimum. The maximum length of
duct is twenty (20) feet (6.1 m) for a 4 in. dia. pipe (See note below).
B) The air intake register must not be installed more than ten (10) feet
(3050 mm) above the base of the fireplace.
C) The fresh air must come from outside the house. The air intake must
not draw air from the attic, from the basement or garage.
D) The air intake should be installed where it is not likely to be blocked by
snow or exposed to extreme wind and away from automobile exhaust
fumes, gas meters and other vents.
E) The duct and register may be installed above or below floor level.
The following components are required:
- Outside air kit (UZI) (includes 4 inch flex that goes up to ten (10) feet
long)
- 4” Adaptor for fireplace connection (supplied with the unit)
Make a 4-1/4” (110 mm) hole in the outside wall of the house at the chosen
location. From outside, place the outside air register in the hole (open
side down) and fasten the register to the wall, with screws as shown (see
Figure 25). Slip the pipe into the insulated sleeve. Place the insulated
pipe over the register tube and over the fireplace’s outside air connector
(see Figure 26). At each end, carefully pull back the insulation and plastic
cover exposing the flexible pipe. Using the aluminium tape provided,
wrap the tape around the joint between the flexible pipe and the air inlets.
Carefully push the insulation and plastic cover back over the pipe. Using
aluminium tape, fasten the plastic cover in place.

Figure 25

OUTSIDE AIR CONNECTION TO THE FIREPLACE
Fireplace
Connection
Aluminum Tape
Plastic
Cover

Insulation
Flexible Pipe
Aluminum Tape

Figure 26

Note: We recommend not to exceed 20 feet of 4” flexible pipe. If you
require a longer length we recommend that you use a 5” diameter flexible pipe for the complete run up to 30 feet and a 6” diameter pipe for a
run of up to 40 feet.

16

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Fireplace

THE CHIMNEY system
Chimney Installation Notes
1. Always install an interior chimney as it will provide better performance.
In areas with continuous temperatures below 0° F (- 18° C), the use of
an exterior chimney increases the likelihood of operating problems such
as low draft, high rate of creosoting, and poor start-up characteristics.
Exterior chimneys are also prone to down drafting and flow reversal.
Installations, which are located on lower floors in the house, such as
in a basement, in combination with outside chimney, are especially
prone to flow reversal. If interior installation is impossible, install an
AC chimney enclosed in an insulated chase.
2. The fireplace model Brentwood LV may be installed only with Security
Chimneys International Ltd 6” diameter chimney systems.
3. A chimney venting a fireplace shall not vent any other appliance.
4. The minimum chimney height is 12 feet (3.7 m). In altitude, add 18”
(450 mm) to the chimney for every 2,000 feet (600 m) above sea
level.
5. All chimney installations must include at least one support. The
maximum length of chimney that can be supported by the fireplace
is 26 feet (8 m).

6. The chimney must extend at least three (3) feet (915 mm) above its
point of contact with the roof and at least two (2) feet (610 mm) higher
than any wall, roof or building within ten (10) feet (3m) of it (Figure
27).
7. If the chimney extends higher than five (5) feet (1,500 mm) above
its point of contact with the roof, it must be secured using a roof
brace.
8. A rain cap must be installed on top of the chimney. Failure to install
a rain cap may cause corrosion problems.
9. Cut and frame square holes in all floors, ceilings, and roof that the
chimney will go through to provide a 2” (50 mm) clearance between
the chimney and any combustible materials. Do not fill this 2” space
with insulation or any other combustible material.
10. Portions of the chimney which may extend through accessible spaces
must be enclosed to avoid contact with combustible materials or
damage to the chimney.
11.When offsets are used, the pipe may not penetrate a ceiling or floor
unless it is running vertical (no 30° offsets).

two (2) feet Min.
ten (10) feet

three (3) feet Min.

Figure 27
Note: 2" clearance to combustibles around chimney components required.
Note: Blown or fill type insulation materials must not be in contact with the
fireplace or in the enclosure frame as described in ‘’Enclosure’’ section.
Note: Local codes may not require firestopping at the ceiling levels for
outside chase installations. However, it is recommended for safety and
the reduction of heat loss.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

17

CHIMNEY INSTALLATION INSTRUCTIONS
1. Cut and frame the holes in the ceiling, floor
and roof where the chimney will pass (see
Figure 28). Use a plumb-bob to line up the
center of the holes. The sizes are indicated
in Table 2 for the floor and ceiling holes
and Table 3 (Page 19) for the roof holes.
CHIMNEY MODEL

SQUARE HOLE
SIZE OPENING

ASHT / HT6103+

12-3/8” (314 mm)

S-2100+ / HT6000+

14-1/8” (359 mm)

AC

15 in (380 mm)

Attic Radiation Shield
ASHT / S2100
HT6103+ / HT6000+
Solid Packed Pipe

Attic Radiation
Shield
Flashing

Roof
Firestop

Figure 29a

Mobile / Manufactured Home with Flat Roof
ASHT / S2100
HT6103+ / HT6000+
Figure 29b

Note: See Table 3 for Sloped Roof Framing

Table 2 - Flat Roof Framing

AC
Air Cooled Pipe

Attic Radiation
Shield

Attic Radiation
Shield

Flashing

Figure 28 - Roof Framing

18

2. From below, install a firestop in each ceiling/
floor separation through which the chimney
will pass. At the attic level, install an attic
radiation shield from above (Figures 29a
through 29d).
3. For ASHT / HT6103+ AND S2100+ / HT6000+
chimneys place the first chimney length on
the fireplace. To lock it in place, turn 1/4
of a turn clockwise. With the AC chimney,
you must use a starter section (AC6SB or
AC6SB30) before installing the first chimney length (Figure 30). Continue installing
chimney lengths making sure to lock each
length in place.
4. Every time the chimney passes through
a ceiling or a wall, install the appropriate
firestop. When you reach the desired height,
install the roof support. When installing a
support, slightly lift the chimney system so
the weight will lie on the support, not on the
fireplace to reduce expansion noises (Refer
to instructions included with the support).
5. Then, put the roof flashing in place and seal
the joint between the roof and the flashing
with roofing pitch (see Figures 30 and 31).
For sloping roofs, place the flashing under
the upper shingles and on top of the lower
shingles. Nail the flashing to the roof, using
roofing nails.
6. Place the spacers and the storm collar over
the flashing, and tighten it with the bolt
supplied. Finally, seal the joint between the
storm collar and the chimney, using silicone
caulking.
7. Install the chimney cap. Once the chimney
cap is in place, the roof flashing can be
washed with a solvent or vinegar and then
painted with rust-proof paint.

Radiation Shield

Figure 29c

Mobile / Manufactured Home with Flat Roof
AC Chimney

Figure 29d

Rain Cap

AC CHIMNEY INSTALLATION
(AIR COOLED GALVANIZED CHIMNEY)

Collar
Flashing

Attic Radiation
Shield
Firestop

Starter Section
Chimney Outside
Air Intake
(required when
using AC chimney)

Outside Combustion
Air Kit

Figure 30

Figure 31

After reaching the location requiring the
elbow, proceed as follows:

AC
Air Cooled Chimney
Chimney

ASHT / HT6103+ / S-2100+ / HT6000+ Chimneys

Collar
Spacer (built
into flashing)

Flashing

Figure 32

Figure 31

Roof Down Slope Hole Size
SLOPE

ASHT / HT6103+

S-2100+ / HT6000+

AC

Roof Pitch

6”

6”

6”

0*

12-3/8” (314 mm)

14-1/8” (359 mm)

15” (380 mm)

2/12

12-9/16” (319 mm)

14-3/8” (365 mm)

15 3/8” (390 mm)

4/12

13” (330 mm)

14-7/8” (378 mm)

16 1/8” (410 mm)

6/12

13-7/8” (352 mm)

15-3/4” (400 mm)

16 7/8” (430 mm)

8/12

14-7/8” (378 mm)

17” (432 mm)

18 1/4” (465 mm)

10/12

16-1/8” (410 mm)

18-3/8” (467 mm)

19 5/8” (500 mm)

12/12

17-1/2” (445 mm)

20” (508 mm)

21 3/8” (545 mm)

* Cross Slope Hole Size
Put the chimney cap into place.
Wash the roof flashing with a solvent or vinegar, then paint it with rust-proof paint.

Table 3

OFFSET CHIMNEY INSTALLATION
After reaching the location requiring the elbow, proceed as follows. The minimum chimney height
when using elbows is:
Minimum Chimney Height Using Elbows
Fireplace Model

Brentwood LV

Chimney Model

ASHT / S2100+ / HT6103+ / HT6000+ / AC

Vertical installation

12 feet (3.66 m)

Two (2) elbows

15 feet (4.57 m)

Four (4) elbows

17 feet (5.18 m)

Table 4
Notes:
• Must return to vertical before penetrating ceiling or floor.
• A maximum of 2 offsets are allowed.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

1. Install the first elbow; turn it in the required
direction. Fasten it to the chimney with
the three (3) 1/2” (12 mm) metal screws
provided with the elbow.
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together: it is recommended to use
three (3) 1/2” (12 mm) screws. If the offset
length is made of two (2) chimney lengths or
more, use an offset or roof support halfway
up the offset. If penetrating a wall, install
a wall radiation shield (see Figures 34 and
36).
3. Use another elbow to turn the chimney
vertically. Secure the elbow, using three
(3) 1/2” (12 mm) screws (provided with the
elbow).
4. Use a plumb-bob to line up the center of
the hole. Cut a hole for the chimney in the
ceiling/floor. Frame this hole as described
previously (refer to section Chimney Installation Instructions).
5. From below, install a firestop (See Figure
29a).
6. A support (ST or SO+) must be used on the
first 15’ section (5 m).
7. Continue with the regular installation.
AC Chimney
1. Install the first elbow. Turn it in the required
direction. To lock it in place, turn 1/8 of a
turn. Fasten the straps attached to the elbow
to the surrounding frame, using nails or
drywall screws (Figure 34).
2. Install the necessary chimney lengths to
achieve the required offset. Lock the chimney
lengths together. If penetrating a wall, use
a wall radiation shield.
3. Use another elbow to turn the chimney
vertically. Lock it to the chimney. Fasten
the straps attached to the elbow to the
surrounding framing using nails or drywall
screws.
4. Use a plumb-bob to line up the center of the
hole. Cut a hole for the chimney in the ceiling.
Frame this hole as described previously.
5. From below, install a firestop (see Figure
29c).
6. Continue with the regular installation.
Note: When using AC chimney, an AC6SB
starter section must be used before installing an elbow. When an offset is needed
immediately off the top of the fireplace, an
elbow starter section, AC6SB30 (H3780), is
available.

19

Offset Dimensions

B
Total Height

A
Chimney
6”

Elbow

15º

Secure
Temp
ASHT

30º

Nova
Temp
HT6103+

45º

Chimney
6”

18”

24”

36”

48”

8” & 48”

12” & 48”

18” & 48”

24” & 48”

36” & 48”

48” & 48”

A

3-5/16”
(84mm)

4-5/16”
(110mm)

5-7/8”
(149mm)

7-7/16”
(189mm)

10-1/2”
(267mm)

13-5/8”
(346mm)

15-3/8”
(391mm)

16-7/16”
(418mm)

18”
(457mm)

19-1/2”
(495mm)

22-5/8”
(575mm)

25-3/4”
(654mm)

B

15-11/16”
(398mm)

19-9/16”
(497mm)

25-3/8”
(645mm)

31-3/16”
(792mm)

42-3/4”
(1086mm)

54-3/8”
(1381mm)

60-15/16”
(1548mm)

64-13/16”
(1646mm)

70-9/16”
(1792mm)

76-3/8”
(1940mm)

87”
(2210mm)

99-9/16”
(2529mm)

A

7-7/16”
(189mm)

9-7/16”
(240mm)

12-7/16”
(316mm)

15-7/16”
(392mm)

21-7/16”
(545mm)

27-7/16”
(697mm)

30-13/16”
(783mm)

32-13/16”
(833mm)

35-13/16”
(910mm)

38-13/16”
(986mm)

44-13/16”
(1138mm)

50-13/16”
(1291mm)

B

20”
(508mm)

23-1/2”
(597mm)

28-11/16”
(729mm)

33-7/8”
(860mm)

44-1/4”
(1124mm)

54-11/16”
(1389mm)

60-9/16”
(1538mm)

64“
(1627mm)

69-1/4”
(1759mm)

74-7/16”
(1891mm)

84-13/16”
(2154mm)

95-1/4”
(2419mm)

A

10-5/16”
(262mm)

13-3/16”
(335mm)

17-3/8”
(441mm)

21-5/8”
(549mm)

30-1/8”
(765mm)

38-5/8”
(981mm)

43-7/16”
(113mm)

46-1/4”
(1175mm)

50-1/2”
(1283mm)

54-3/4”
(1391mm)

63-1/4”
(1607mm)

71-11/16”
(1818mm)

B

17-13/16”
(452mm)

20-5/8”
(524mm)

24-7/8”
(632mm)

29-1/8”
(740mm)

37-5/8”
(956mm)

46-1/8”
(1172mm)

50-15/16”
(1294mm)

53-3/4”
(1365mm)

58”
(1473mm)

62-1/4”
(1581mm)

70-3/4”
(1797mm)

79-3/16”
(2011mm)

15º

30º

Elbow

15”
AC
6”

30”

Two Lengths Between Elbows

12”

Offset &
Height

Nova Temp
HT6000

One Length Between Elbows
8”

Elbow

Secure
Temp
S2100+

Chimney
6”

Offset &
Height

Horizontal Offset

One Length Between Elbows

Two Lengths Between Elbows

8”

12”

18”

24”

36”

48”

8” & 48”

12” & 48”

18” & 48”

24” & 48”

36” & 48”

48” & 48”

A

3-5/16”
(84mm)

4-5/16”
(110mm)

5-7/8”
(149mm)

7-7/16”
(189mm)

10-1/2”
(267mm)

13-5/8”
(346mm)

15-1/2”
(394mm)

16-1/2”
(419mm)

18-1/16”
(459mm)

19-5/8”
(498mm)

22-3/4”
(578mm)

25-13/16”
(656mm)

B

16”
(406mm)

19-7/8”
(505mm)

25-11/16”
(652mm)

31-1/2”
(800mm)

43-1/16”
(1094mm)

54-5/8”
(1387mm)

61-7/16”
(1561mm)

65-1/4”
(1657mm)

71-1/16”
(1805mm)

76-7/8”
(1953mm)

88-1/2”
(2248mm)

100-1/16”
(2542mm)

A

7-3/8”
(187mm)

9-3/8”
(238mm)

12-3/8”
(314mm)

15-3/8”
(391mm)

21-3/8”
(543mm)

27-3/8”
(695mm)

30-7/8”
(784mm)

32-7/8”
(835mm)

35-7/8”
(911mm)

38-7/8”
(987mm)

44-7/8”
(1140mm)

50-7/8”
(1292mm)

B

20-11/16”
(525mm)

24-3/16”
(614mm)

29-3/8”
(746mm)

34-9/16”
(878mm)

44-15/16”
(1141mm)

55-5/16”
(1405mm)

61-3/8”
(1559mm)

64-7/8”
(1648mm)

70-1/16”
(1780mm)

75-1/4”
(1911mm)

35-5/8”
(2175mm)

96”
(2438mm)

---

12”

18”

---

36”

48”

---

12” & 48”

18” & 48”

---

36” & 48”

48” & 48”

A

-------

4-13/16”
(122 mm)

6-1/8”
(156 mm)

-------

11”
(280 mm)

14-1/8”
(359 mm)

-------

16-7/8”
(429 mm)

18-7/16
(468 mm)

-------

23”
(584 mm)

26-3/16”
(665 mm)

B

-------

27-11/16”
(703 mm)

33-1/2”
(851 mm)

-------

50-7/8”
(1292 mm)

62-1/2”
(1588 mm)

-------

72-5/8”
(1845 mm)

78-7/16”
(1992 mm)

-------

95-3/4”
(2432 mm)

107-3/8”
(2727 mm)

A

-------

9-3/8”
(238 mm)

12-3/8”
(314 mm)

-------

21-3/8”
(543)

27-3/8”
(695 mm)

-------

32-5/8”
(829 mm)

35-5/8”
(905 mm)

-------

44-5/8”
(1134 mm)

50-5/8”
(1286 mm)

B

-------

25-3/4”
(654 mm)

31”
(787 mm)

-------

46-1/2”
(1181 mm)

57”
(1448 mm)

-------

66”
(1676 mm)

71-1/4”
(1810 mm)

-------

86-7/8”
(2207 mm)

97-1/4”
(2740 mm)

Offset &
Height

One Length Between Elbows

Two Lengths Between Elbows

NOTE: With the AC chimney, a starting section must be used on top of the fireplace.
Figure 33

20

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ANGLED WALL RADIATION SHIELD
(RSM+ and RSMI30)
When traversing a combustible wall with the chimney at a 30º or 45º
angle, an angled firestop or wall radiation shield must be installed. Only
one is required.
Support

ACRS

Straps
Straps

Chimney AC

Starter Section

Note: 45º angle for Canada only (RSMI45)
In cold climate locations (climates where temperatures will fall below 32°
F / 0° C), we recommend that you use the insulated wall radiation shield
since it will maintain the home’s thermal barrier.
RSM+ and RSMI30
(RSMI45 - Canada Only)
Chimney Model

Angle

Hole Size

ASHT / HT6103+ (6”
dia). Canada only

30º

283 mm x 781 mm (11-1/8” x 30-3/4”)

45º

283 mm x 518 mm (11-1/8” x 20-3/8”)

S-2100+ / HT6000+ /
AC (6” dia).

30º

327 mm x 881 mm (12-7/8” x 34-11/16”)

30º

380 mm x 972 mm (15” x 38-1/4”)

Table 5

Insulated Wall
Note: This illustration is not to scale. It represents how the chimney
must be supported. A 30 degree offset only is allowed in the USA
and a 45 degree maximum offset is allowed in Canada.

Figure 34 - Offset Chimney Installation

Drywall

Rain Cap

Collar

Figure 36

Insulated Wall
Radiation Shield

Roof Flashing

Offset Support

Framing
2” x 3”
Insulated Wall
Radiation Shield

Figure 35

Note: In cold areas it is recommended to
protect the chimney in a insulated chase.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

21

CHIMNEY SUPPORT INSTALLATION
Universal Roof Support

18” (460 mm)

When installing a support, slightly lift the chimney system so the weight
will lie on the support, not on the fireplace to reduce expansion noises.
This support has three possible uses:
1. For ASHT / HT6103+ and S-2100+ / HT6000+, it must be used on a
roof to support the chimney.
2. It may be used on a floor, ceiling or roof above an offset to support
the chimney above the offset.
3. It may be used on a floor, ceiling or roof as a supplementary support.

16” (410 mm)

18” (460 mm)

16” (410 mm)

18” (460 mm)

Table 6 gives maximum height of supported chimney.
NOTE: For the AC chimney, a support section must be used every 40 feet
(12 m) instead of the universal roof support (ST).
For roof support installation, refer to the instructions provided with the
support.

Universal Offset Support
This support is used to support the chimney above an offset. When
the chimney offset is used to traverse a wall this support may be used
on the wall to support the chimney. The maximum heights are given in
Table 6. For offset support installation, refer to the instructions provided
with the support.

CHIMNEY MODEL

Figure 37

CHIMNEY ADAPTOR (S-2100+ / HT6000+) CANADA ONLY
The fireplace is normally supplied with a chimney adaptor suitable for the
ASHT / HT6103+ chimney. If you want to install a S-2100+ / HT6000+
chimney, an adaptor is available (6UCA) (Figure 38). A separate starter
section will also be required if AC chimney is installed.

Chimney Adaptor Canada only

MAXIMUM HEIGHT OF
SUPPORTED CHIMNEY
OFFSET SUPPORT

ROOF SUPPORT

ASHT / HT6103+ (6” dia).

28 feet (8.54 m)

29 feet (8.84 m)

S-2100+ / HT6000+ (6” dia).

18 feet (5.49 m)

20 feet (6.1 m)

AC (6” dia).

40 feet (12.19 m)

50 feet (15.20 m)

Table 6

CHIMNEY CHASE AND MULTIPLE TERMINATIONS
For the purpose of this manual, a chimney chase is considered a part of
the chimney system rather than part of a building. The termination must
be placed a minimum of 18” (460 mm) above the chase.
For installations where more than one chimney is located in the same
chase or within the same area, we suggest that their terminations be
separated by at least 16” (410 mm) horizontally, and 18” (460 mm) vertically. This separation is to prevent smoke migrating from one chimney
to another (see Figure 37).

22

Figure 38

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION

Follow these steps:

WARNING: Before starting the installation, the masonry chimney
must be inspected by a qualified chimney sweep.

1- Position the fireplace in its location. Temporarily install the ASHT
elbow on the top of the fireplace and, using a level, mark with an oval
the location where the flue liner will enter the masonry chimney.
2- In the middle of the oval, drill a hole in the masonry chimney at 30º.
3- Increase the size of the hole until a or 30º TUBINOX liner elbow can
be easily slipped through.
4- Slide the liner down from the top of the masonry chimney until you
reach the hole level.
5- Slip through the hole a 30º liner elbow and connect it to the liner.
6- Add a small liner section to the liner elbow which will allow the liner to
extend at least 12” (measured at the top of the liner) from the masonry
chimney.
7- Seal the opening around the liner with high temperature refractory
cement.
8- The next steps must be done in the following order:

The following requirements must be respected:
1. The chimney must be absolutely clear of any soot residue or creosote.
Check for cracks, loose or missing bricks that could inhibit correct
installation of the liner.
2. The clearance to combustible must be a minimum of 1” between the
outside of the masonry and any wood framing or loose insulation.
3. The chimney must be built in accordance with the current building
code.
4. No other appliance can be connected to the same chimney.
5. The clearances to combustible for the BISUMA30 connectors are 2”
on the side and bottom and 16” at the top.
6. The connector parts are not necessary if the connection between
the insulated length and the stainless steel liner is done within the
masonry chimney.
Installation:
The chimney must be relined with a stainless steel liner model TUBINOX
or Projet SS of the same diameter as the outlet of the fireplace.
For connection at a 30º angle, a special connector (BISUMA30) must be
used to connect the liner to the insulated chimney.
* IMPORTANT NOTE - The use of a 45º connector (BISUMA) is approved
for use in Canada ONLY. Installations in the USA must use the 30º
connector (BISUMA30).

See typical installation illustrated below.
A. Select the ASHT length that will fit between the elbow and the liner
so that it will slide at least 2” over the liner section (You may need to
cut the liner for a better fit).
B. Take that section and the BISUMA30 cover and slide it over the liner.
Make sure you have enough opening to be able to install the ASHT
elbow without difficulty.
C. Install the 30º elbow on the fireplace.
D. Slide the length section back down on the elbow and twist lock the
two together.
E. Pull the cover down over the length and install the insulation pad over
the liner; be careful to cover the liner completely.
F. Slide back the cover over the insulation and fix it in place using the 3
metal screws supplied.

1” Clearance

High-Temp.
Cement
Insulation
Pad & Cover
* Insulated
Elbow ASHT
or HT6103+

3 Screws

Firestop
TUBINOX or Projet SS
Stainless Steel Liner
TUBINOX or Projet SS
Liner Must Slide at Least
2” Inside Length
Insulated
Length

6’ 8”

Masonry Chimney,
New or Existing
FIREPLACE

Figure 39
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

23

Optional installation accessories
Installation Accessories
Description

Fireplace Kits
Cat./Part No.

Blower motor speed control (wall mount), VRUW

Finishing Kits (Required - Order Separately)
Louver kit

LOUVRECF

OR
Clean face kit

CAPPINGCF

Outside Air Kit (Required - included w/fireplace)
Outside Air Coupler to connect outside air UZI to fireplace,
UZIAD

UZIAD

Outside Air Ducting - includes 4” insulated flex x 10’ long,
UZI

UZI

Gravity Kits (REQUIRED WITH CLEAN FACE KIT)
Gravity Kit - Complete double ducting system w/adaptor
including: 2 elbows 90º, 2 telescopic lengths, 2 grill supports
and 2 black grills, 7B30ZK-1

7B30ZK-1

Gravity Kit Accessories

Masonry Chimney Adaptor, 30º, BISUMA30
(for use with TUBINOX liner)

Cat./Part No.
VRUW
BISUMA30

Central Forced Air Kit Accessories u
Central Forced Air Kit, Central forced air kit including: blower
(BISZY), flex adaptor (BISAF), 2 clamps, variable speed
control (VRUW), thermo-disk (VTU), fan to flexible pipe
adapter (BISAVF), back draft damper (BISBD), aluminium
tape, BISFWK-1
Fireplace to Flex adaptor and 2 clamps, BISAF

BISFWK-1

BISAF

Flexible pipe 5” I.D. x 15 ft. Long, 5FLEX15

5FLEX15

Flexible pipe 5” I.D. x 30 ft. Long, 5FLEX25

5FLEX25

Blower 250 CFM for central forced air kit, BISZY

BISZY

Blower variable speed control with decorative wall plate for
(BISZY), VRUW

VRUW

Black grill with support, Part# 7B30ZO

7B30ZO

Thermo-disk, on/off blower control (for BISZY), VTU

Brass grill (for 7B30ZK), 7B30ZGB

7B30ZGB

Blower to flexible pipe adaptor, BISAVF

Elbow 90º, 8” dia., 7B26ZE90

7B26ZE90

Heating and cooling thermostat, 24V, HCTW

HCTW

7B26ZE45

Backdraft damper, BISBD

BISBD

Elbow 45º, 8” dia., 7B26ZE45
Telescopic length, 8” dia., 7B26ZLA

7B26ZLA

Adjustable length 8” dia (2” - 5”), 7B26ZL2A

7B26ZL2A

Wall Radiation shield, 7B26ZR

24

Description

VTU
BISAVF

7B26ZR

Length five (5) feet, 8KL5

8KL5

Length four (4) feet, 8KL4

8KL4

Length three (3) feet, 8KL3

8KL3

Length two (2) feet, 8KL2

8KL2

Length one (1) feet, 8KL1

8KL1

u Not tested under EPA certification. If installed, this appliance no
longer qualifies for EPA certification.

Chimney - PARTS AND COMPONENTS LISTs

Fireplace Model Brentwood LV - Approved Venting Components manufactured by Security Chimneys International only.

Secure Temp ASHT 1” High Temp. Insulated Stainless Steel Chimney

6” I.D and 8” O.D., Double-Wall Stainl. Steel, Listed to CAN/UCL-S604 and UL-103HT

Description

Part/Cat. No.

Lengths and Misc. Chimney Components
8” length, 6” Dia., 6L8

6L8

12” length, 6” Dia., 6L12

6L12

18” length, 6” Dia., 6L18

6L18

24” length, 6” Dia., 6L24

6L24

36” length, 6” Dia., 6L36

6L36

48” length, 6” Dia., 6L48

6L48

Adjustable Length 12”, 6” Dia., 6LA

6LA

15º elbow, 6” Dia., 6E15

6E15

30º elbow, 6” Dia., 6E30

6E30

Rain Termination Cap, 6” Dia., 6CC

6CC

Spark Arrester Screen (universal spark arrester band), PE

PE

Wall Band, BM

BM

Supports
Offset Support, SO

SO

Roof Support, ST

ST

Roof Brace, BS2

• 6” diameter chimney - AC (air cooled), Secure Temp™ ASHT (or
Nova Temp™ HT6103+) and Secure Temp S-2100+ (or Nova Temp
HT6000+).
• 6” diameter chimney for relining masonry chimneys - TUBINOX
chimney (or PROJET SS), 6” diameter with adaptor for installation in
a masonry chimney.
Notes:

jNova Temp HT6000+ is equivalent to Secure Temp S-2100+
kNova Temp HT6103+ is equivalent to Secure Temp ASHT
lThis appliance is equipped with the ASHT Chimney Adaptor.

When other
chimney is used, a chimney adaptor for that chimney will be required.

mChimney Adaptor (S-2100+ / HT6000+) for CANADA ONLY -

If you want to
install a S-2100+ / HT6000+ chimney, an adaptor is available (6UCA).

nAC Chimney is NOT recommended at elevations above 4,000 feet or in cold
climates (climates where temperatures will fall below 32° F / 0° C). When
using AC chimney, an AC6SB starter section must be used before installing
an elbow. When an offset is needed immediately off the top of the fireplace,
an elbow starter section, AC6SB30 (H3780), is available.

BS2

Firestops
Firestop, 6BF

6BF

Radiation Shield, 6RS

6RS

Insulated Attic Radiation Shield, 6RSA
Insulated Wall Radiation Shield, 6RSM

6RSA2
6RSM

Insulated Wall Radiation Shield, 30º, 6RSMI30

6RSMI30

Uninsulated Wall Radiation Shield, 30º, 6RSM30

6RSM30

Attic Radiation Shield

H0487

Roof Flashings
Flat Roof Flashing, 6FR

6FR

1/12 - 7/12 (5º - 30º), 6FAR

6FAR

8/12 - 12/12 (30º - 45º), 6FBR

6FBR

Storm Collar, 6FC

6FC

25

Chimney - PARTS AND COMPONENTS LISTs
(AC) Air-Cooled Chimney System*

TUBINOX LL Chimney Lining System

6” I.D. and 11” O.D. Air Cooled, Stainl. Steel inner and zinc coated steel exterior

AC Starter Adaptors

* AC Chimney is NOT recommended at elevations above 4,000 feet or in cold climates
(climates where temperatures will fall below 32° F / 0° C).

Cat./Part No.

Starter Section (adaptor), 6”, AC, AC6SB

H3779

Starter 30º Elbow, 6” AC, AC6SB30

H3780

The following outside air kit is required if installing an AC chimney system
Chimney Outside Air Kit (flex, insulation, outside register
and coupling), ACZI

H1967

Cat./Part No.

6” Length, 6” Dia., 6LL6

6LL6

12” Length, 6” Dia., 6LL12

6LL12

24” Length, 6” Dia., 6LL24

6LL24

36” Length, 6” Dia., 6LL36

6LL36

48” Length, 6” Dia., 6LL48

6LL48

Adjustable Length (7” to 11”), 6” Dia., 6L7A

6L7A

Split Base Tee, 6” Dia., 6LT

6LT

Tee Cap, 6” Dia., 6TCS

6TCS

Twist Lock Tee Cap, 6” Dia., 6LTC

6LTC

H0472

Elbow 30º, 6” Dia., 6LE30

6LE30

18” Length, 6” Dia. x 12” Long, AC6L18

H0473

Elbow 45º, 6” Dia., 6LE45

6LE45

36” Length, 6” Dia. x 36” Long, AC6L36

H0474

Elbow 90º, 6” Dia., 6LE90

6LE90

48” Length, 6” Dia. x 48” Long, AC6L48

H0475

Rain Termination Cap (regular), 6” Dia., 6LCS

6LCS

15º Elbow, 6” Dia., AC6E15

H0476

Rain Termination Cap (deluxe), 6” Dia., 6LCC

6LCC

30º Elbow, 6” Dia., AC6E30

H0477

Spark Arrester Screen (universal spark arrester band), PE

Rain Termination Cap, 6” Dia., AC6CPR

H0478

Lengths and Misc. Chimney Components
12” Length, 6” Dia. x 12” Long, AC6L12

Spark Arrester Screen (universal spark arrester band), PE
Wall Band, XBM

PE
XBM

Supports
Offset Support, SO
Support Section, AC6SL

PE

Supports
Top Support, 6LST

6LST

Support Assembly, 6LSA

6LSA

Interior Support, 6LSB

6LSB

SO

Adaptor Flexible Pipe (male), 6LAAM

H0481

Adaptor Flexible Pipe (female), 6LAAF

Roof Support, ST

ST

Stainless Steel Flex - five (5) feet Long, 6LLFLEX

Roof Brace, BS2

BS2

Adjustable Insulated Wall Radiation Shield 6” - 12”, 6LRSMI

6LAAM
6LAAF
6LLFLEX
6LRSMI

Adaptors to Masonry Chimney

Roof Flashings
Flat Roof Flashing, ACF

H0494

1/12 - 7/12 (5º - 30º), AC Adj. Roof Flashing, FA

H0495

8/12 - 12/12 (30º - 45º), AC Adj. Roof Flashing, FB

H0496

Storm collar, ACFC

H0500

Misc.

26

Listed to ULC-S635M, UL-1777 and ULC-S640M at 2100º F

Description

One of the following adaptors is required
if installing an AC chimney system

Description

Rigid Stainless Steel Liner For Relining A Masonry Chimney, 6” Diameter

Telescopic attic radiation shield, ACRST

H0498

Firestop, ACBF

H0485

Radiation Shield, ACRS

H0486

Attic Radiation Shield, ACRSA

H0487

Insulated Wall Radiation Shield, 30º, ACRSMI30

H0489

Masonry Chimney Adaptor, 45º, BISUMA
(for use with TUBINOX liner) CANADA ONLY

BISUMA

Masonry Chimney Adaptor, 30º, BISUMA30
(for use with TUBINOX liner)

BISUMA30

SPECIFICATIONS

CLEARANCE TO COMBUSTIBLES

Cat. No.

Model

H8295

Brentwood™ LV

The following clearances meet the minimum requirements for a safe
installation:
Side wall: 24” (610 mm) measured from the fireplace side.
Ceiling:

Product Reference Information
Weight

385 lbs

Height

36”

6’ 8” (2,032 mm) measured from the base of the fireplace.

Fireplace enclosure:
Bottom: 0”
Side: 0” to spacer
Back: 0” to spacer
Top: Do not fill the space above the fireplace with any material
(Except the wood framing. See Page 11, Figure 11).

Width

36”

Depth

24-1/2”

Firebox W x H x D - measured in front

22” x 11-3/4” x 12”

Chimney weight ASHT (6” dia)

6.25 lb per linear foot

Chimney: 2” (50 mm)

Chimney weight AC (6” dia)

3.25 lb per linear foot

Mantel: 45” (1143 mm) measured from the base of the fireplace.

27

REPLACEMENT PARTS - Brentwood™ LV

Brentwood™ LV
Item #

Description

Cat./Part No.

1

Baffle refractory (2 pieces)

PR-ISO2205

2

Back refractory

PR-SR2996

3

Right side refractory

PR-SR2997D

4

Left side refractory

PR-SR2997G

5

Bottom refractory

6

Front refractory, right side - ash lip

PR-SR2202D

7

Front refractory, left side - ash lip

PR-SR2202G

8

Secondary air tube

PR-SR2271

9

Bracket, secondary air tube lock

PR-SR2214

10
11
12
13
14

Facing:
Top trim
Bottom trim
Top frame
Left side frame
Right side frame

15

Fireplace top

PR-SR2500

16

Fireplace left side

PR-SR2502

17

Fireplace left side

PR-SR2503

18

Fireplace back

PR-SR2499

19

Touch-up paint, aerosol, black metallic
SBMB6309

20

Louvers, upper and lower (set of 2)

21

Complete door

22

Wooden door handle

PR-SR2856

23

Door handle rod and lock

PR-SR2855

24

Ceramic glass panel

25

Gasket, door, 77-3/4” (5/8” dia.)

PR-SR1823P

26

Gasket, glass, 74” (3/16” x 1”)

PR-SR1685J

27

Hinge assembly, fireplace and door

PR-SR1933

28

Blower (heat activated on/off, prewired)

UZY6

29

Snap Disc, Blower

VTU

30

Andiron (2)

PR-SR2324

31

Cast iron log retainer bar

PR-SR2323

PR-SR2201

PR-SR3033
PR-SR3020
PR-SR2995
PR-SR2994G
PR-SR2994D

H8159
LOUVRECF
PR-SR3003LV

PR-SR3004

Contact an Authorized Lennox Hearth Products dealer to obtain any of
these parts. Never use substitute materials not approved by Lennox
Hearth Products. Use of non-approved parts can result in poor performance and safety hazards.

28

REPLACEMENT PARTS - Brentwood™ LV

17
18

12

15
8
20
16

1

10
14
30

19
22

23

24
21
11

2

3

20
25

26
5

31
13

PA I N T

6

4
7

28

29

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

29

Warranty
Your fireplace is covered by a limited warranty. Please read the warranty
to be familiar with its coverage.
Retain this manual. File it with your other documents for future reference.

Product reference information
We recommend that you record the following important information
about your fireplace. Please contact your Lennox Hearth Products dealer
for any questions or concerns. For the number of your nearest Lennox
Hearth Products dealer, please call 1-800-9-LENNOX.

Replacement parts
See Page 28 for a complete replacement parts list. Use only parts supplied from the manufacturer.

Normally, all parts should be ordered through your Lennox Hearth
Products distributor or dealer. Parts will be shipped at prevailing prices
at time of order.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at www.Lennox.com

Your Fireplace's Model Number_________________________________________
Your Fireplace's Serial Number_________________________________________
The Date On Which Your Fireplace Was Installed____________________________
Your Dealer's Name__________________________________________________
Your Dealer's Phone Number___________________________________________

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.

Printed in Canada © 2011 Lennox Hearth Products

30

P/N 506023-13 REV. A 02/2011

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Create Date                     : 2011:02:25 10:43:27-08:00
Creator                         : Adobe InDesign CS4 (6.0.6)
Modify Date                     : 2011:02:25 10:45:51-08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2011:02:25 10:45:51-08:00
Creator Tool                    : Adobe InDesign CS4 (6.0.6)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 13845 bytes, use -b option to extract)
Instance ID                     : uuid:d3e3fa8c-3fd7-438b-be9d-1b132f39566e
Document ID                     : xmp.did:2AC56DBDE9C4DF11A4749E9D9E96E245
Original Document ID            : adobe:docid:indd:b34bef17-2d42-11df-818e-8e17e4c42fde
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:29C56DBDE9C4DF11A4749E9D9E96E245
Derived From Document ID        : adobe:docid:indd:b34bef17-2d42-11df-818e-8e17e4c42fde
Derived From Original Document ID: adobe:docid:indd:b34bef17-2d42-11df-818e-8e17e4c42fde
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:12CD7AE480A5DF11B0A7D83E4B4A8325, xmp.iid:13CD7AE480A5DF11B0A7D83E4B4A8325, xmp.iid:8019642815C1DF11BFB495964A0C9BC8, xmp.iid:045A516C8BC2DF118648BEDBA7B2F4FA, xmp.iid:26C56DBDE9C4DF11A4749E9D9E96E245, xmp.iid:27C56DBDE9C4DF11A4749E9D9E96E245, xmp.iid:28C56DBDE9C4DF11A4749E9D9E96E245, xmp.iid:29C56DBDE9C4DF11A4749E9D9E96E245, xmp.iid:2AC56DBDE9C4DF11A4749E9D9E96E245, xmp.iid:40714AABBAC5DF11A496866CBDCE8037, xmp.iid:42714AABBAC5DF11A496866CBDCE8037, xmp.iid:43714AABBAC5DF11A496866CBDCE8037, xmp.iid:1C60C4905DC6DF1184BBC2B1B5688FDE, xmp.iid:9E8C79D89DC6DF1184BBC2B1B5688FDE, xmp.iid:A1D63D85E5C7DF119B1D9BF4189D47C5, xmp.iid:B2A0E91D49CBDF118BEDD6776B6BAB0F, xmp.iid:1FA208101DCCDF118EDBF2FE6737BE59, xmp.iid:0C7FB14EB2CCDF11886FA0EE2408CA00, xmp.iid:FD5C601181CDDF118BD8C9ACC8FC0D05, xmp.iid:FF5C601181CDDF118BD8C9ACC8FC0D05, xmp.iid:005D601181CDDF118BD8C9ACC8FC0D05, xmp.iid:DA2BBB1E2418E0119113B631A99552E2, xmp.iid:DB2BBB1E2418E0119113B631A99552E2, xmp.iid:DD2BBB1E2418E0119113B631A99552E2, xmp.iid:3C0A9C55ED18E011AF1AA0D07BBFAA46, xmp.iid:3E0A9C55ED18E011AF1AA0D07BBFAA46, xmp.iid:450A9C55ED18E011AF1AA0D07BBFAA46, xmp.iid:B690E7E5B219E011A193A17FDCA68D3C, xmp.iid:B790E7E5B219E011A193A17FDCA68D3C, xmp.iid:FF4616E3BC1AE0119E9E84130EE65F2F, xmp.iid:004716E3BC1AE0119E9E84130EE65F2F, xmp.iid:2D12EEB0D11CE011B7128DF2C7C8A799, xmp.iid:7CF2F408E81CE011B7128DF2C7C8A799, xmp.iid:6CCD18B2121DE011B7128DF2C7C8A799, xmp.iid:6ECD18B2121DE011B7128DF2C7C8A799, xmp.iid:2704EE572F2AE011BA2FC10A08104BDE, xmp.iid:EC4D6A1C102BE011BA2FC10A08104BDE, xmp.iid:F14D6A1C102BE011BA2FC10A08104BDE, xmp.iid:10B487B8582DE0119A7EAC920CCEA3A4, xmp.iid:11B487B8582DE0119A7EAC920CCEA3A4, xmp.iid:F5F2C645952DE0119A7EAC920CCEA3A4, xmp.iid:C36748224B2EE011BF4BDE8D06D7F6C3, xmp.iid:978C0D128030E0118F63B03C7B981062, xmp.iid:274E2D72D732E01185F4F925C9B09224, xmp.iid:448C670E5B38E011840FB7C803258DA3, xmp.iid:0B5BAD81E439E01193AC9093CA60A7D2, xmp.iid:67E1D601AB3EE011B1D1A5617E2F9AB0
History When                    : 2010:08:11 12:44:45-07:00, 2010:08:11 12:44:45-07:00, 2010:09:15 15:59:06-07:00, 2010:09:17 15:55:06-07:00, 2010:09:20 15:00:04-07:00, 2010:09:20 15:12:17-07:00, 2010:09:20 15:28-07:00, 2010:09:20 15:30:36-07:00, 2010:09:20 15:30:37-07:00, 2010:09:21 12:58:57-07:00, 2010:09:21 15:57:50-07:00, 2010:09:21 15:58:09-07:00, 2010:09:22 08:25-07:00, 2010:09:22 16:05:44-07:00, 2010:09:24 15:57:21-07:00, 2010:09:28 15:50:39-07:00, 2010:09:29 15:59:36-07:00, 2010:09:30 15:48:24-07:00, 2010:10:01 10:26:47-07:00, 2010:10:01 13:01:33-07:00, 2010:10:01 13:03:16-07:00, 2011:01:04 09:00:23-08:00, 2011:01:04 09:01:39-08:00, 2011:01:04 15:54:37-08:00, 2011:01:05 09:00:44-08:00, 2011:01:05 10:01:45-08:00, 2011:01:05 15:59:23-08:00, 2011:01:06 15:48:58-08:00, 2011:01:06 16:04:41-08:00, 2011:01:07 16:18:58-08:00, 2011:01:07 16:24:16-08:00, 2011:01:10 09:03:27-08:00, 2011:01:10 10:32:52-08:00, 2011:01:11 13:55-08:00, 2011:01:11 14:33:46-08:00, 2011:01:28 09:56:12-08:00, 2011:01:28 11:27:54-08:00, 2011:01:28 15:53:44-08:00, 2011:01:31 13:04:26-08:00, 2011:01:31 13:08:38-08:00, 2011:02:01 12:49-08:00, 2011:02:03 07:48:34-08:00, 2011:02:04 10:02:55-08:00, 2011:02:08 11:28:20-08:00, 2011:02:14 15:11:17-08:00, 2011:02:16 07:55:32-08:00, 2011:02:22 12:37:08-08:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:D5407F143CCBDB11A692CF7ABFB88159, xmp.iid:CA723AA0588FDF118A8B90AE2C49069C, uuid:15f3f21e-9631-4fd9-87cd-4a941d55a50f, uuid:9a1d08ef-24ca-4350-b1ce-98c144b76dbe, uuid:e15450fb-a969-403b-8bb8-be01e53f2710, uuid:8252021f-170a-48e7-b6dd-b8f13a7f969d, xmp.iid:E1C035091918E011A9FA8ACF743CAA68, xmp.iid:E2C035091918E011A9FA8ACF743CAA68, xmp.iid:E0C035091918E011A9FA8ACF743CAA68, uuid:5c4a150e-e563-44d1-887f-bb5b7a25b180, uuid:dfd4df9b-d5a1-4e6f-be74-a93cfe34912a, uuid:5EB344F71A37DD11805FF7CBF6998DF1, uuid:cd8ad833-a6a7-43ea-bd05-cf0a8a7c8642, uuid:4908a676-ef4c-4f28-8842-f77f084286ce, xmp.iid:E5C035091918E011A9FA8ACF743CAA68, uuid:54942caf-eab7-474a-9ba9-40f95792c27b, uuid:33EDD339376DDD11AB3FC1A34D4C3F5C, uuid:aa6b13da-696f-4988-aa45-85512400fc73, xmp.iid:E6C035091918E011A9FA8ACF743CAA68, uuid:BF2C5D81594FDD1182E6BFE92EADA550, xmp.iid:21606E03C219E0119020C069EC9863B7, uuid:B3CEBDBB0724DC11A94BD6AD86225631, uuid:d25bb938-5c84-4869-8b18-3bbc02947846, uuid:9de17176-68e7-4250-83fa-e4655b946e3f, uuid:d25bb938-5c84-4869-8b18-3bbc02947846, uuid:8C2B37901AE7DD1190ADC6C9C63C951F, uuid:fc725913-5748-40c0-8fd5-1cb31714d79b, uuid:ababb62e-f753-4d36-afaa-6cc02db28bcc, xmp.iid:DFC035091918E011A9FA8ACF743CAA68, xmp.iid:5C6693AEA8C5DF11965193B97A5E629D, uuid:fd2530ac-b637-40ca-b7ad-9eb0d9da63b2, uuid:7cb475b6-7180-4c41-a331-2eb6a85020f1, uuid:5f52b7dc-76ff-43b6-823c-ca1cc017c208, uuid:07ad51d8-7b05-46b4-8996-b0fb7716b911, uuid:0193b95c-2328-4f42-a5f7-f19ce86bad49, xmp.iid:E7C035091918E011A9FA8ACF743CAA68, xmp.iid:173321AF4818E011A9FA8ACF743CAA68, uuid:f0f809a4-e21c-4e96-b57c-b32dbae8f469, uuid:23198af9-e01c-4599-840d-c92bb4b3cca0, uuid:38067566-d926-49db-85b6-9bb00baedc29, uuid:38067566-d926-49db-85b6-9bb00baedc29, uuid:315bbd2a-94ba-4889-8fe8-e489e3b9f7c1, uuid:112b46eb-a672-4f7e-89b6-b8d78119b0f2, uuid:112b46eb-a672-4f7e-89b6-b8d78119b0f2, uuid:8018ff95-6b89-4f6e-8a6d-88571106b451, uuid:444c9016-e833-48dc-987b-6221c78bc1ea, uuid:1DF6AC7E2A66DC119587E840D3F2AB0E, uuid:20F6AC7E2A66DC119587E840D3F2AB0E, uuid:bc7f1c2d-41ca-4ec5-a785-df66e34132bb, uuid:fd674328-758f-4939-986a-e0bc759a980f, uuid:45839b0a-42be-4a6b-8eff-ad4cfc3b66c0, uuid:5e5e409a-d1c2-4332-9916-3d906545138e, xmp.iid:143321AF4818E011A9FA8ACF743CAA68, uuid:01d1f553-d60c-41e2-95b8-deb4e3d21af5, uuid:25fcb661-848e-40fc-8864-28701ae7042a, uuid:d4d069e7-070d-4003-9f46-2bf1bc661f4a, xmp.iid:23606E03C219E0119020C069EC9863B7, uuid:7c4cd1ea-38c9-48dc-aefe-cefddee3b685, uuid:2ddb9461-f414-4ff6-9289-b6bfef7ea4b4, xmp.iid:CA723AA0588FDF118A8B90AE2C49069C, uuid:A054675EDA15DC1189C2BF8758B98E68
Manifest Reference Document ID  : uuid:D4407F143CCBDB11A692CF7ABFB88159, xmp.did:CA723AA0588FDF118A8B90AE2C49069C, xmp.did:153321AF4818E011A9FA8ACF743CAA68, xmp.did:163321AF4818E011A9FA8ACF743CAA68, xmp.did:596693AEA8C5DF11965193B97A5E629D, uuid:64d6ed79-7b54-4b76-8626-8443a657bc89, xmp.did:E1C035091918E011A9FA8ACF743CAA68, xmp.did:E2C035091918E011A9FA8ACF743CAA68, xmp.did:E0C035091918E011A9FA8ACF743CAA68, xmp.did:E4C035091918E011A9FA8ACF743CAA68, xmp.did:20BFE0865E2EE011945DC46D4B96A23F, uuid:0ADB377B841EDC1190728D26E9C638D5, xmp.did:5A6693AEA8C5DF11965193B97A5E629D, xmp.did:DEC035091918E011A9FA8ACF743CAA68, xmp.did:E5C035091918E011A9FA8ACF743CAA68, uuid:40DA3F24B1EEDC11B8A2A5FC4DE0B02D, uuid:31EDD339376DDD11AB3FC1A34D4C3F5C, uuid:64d6ed79-7b54-4b76-8626-8443a657bc89, xmp.did:E6C035091918E011A9FA8ACF743CAA68, xmp.did:21606E03C219E0119020C069EC9863B7, uuid:A7802C050224DC11A94BD6AD86225631, uuid:6b486162-3153-4289-a6d4-672b918f75ac, xmp.did:8D847A8F5C2AE011A50EF3D8894D1A11, uuid:6b486162-3153-4289-a6d4-672b918f75ac, uuid:8A2B37901AE7DD1190ADC6C9C63C951F, xmp.did:22606E03C219E0119020C069EC9863B7, uuid:A4ACC6059A2EDE11A493A9AA8C928A30, xmp.did:DFC035091918E011A9FA8ACF743CAA68, xmp.did:5C6693AEA8C5DF11965193B97A5E629D, xmp.did:5D6693AEA8C5DF11965193B97A5E629D, xmp.did:5E6693AEA8C5DF11965193B97A5E629D, xmp.did:5F6693AEA8C5DF11965193B97A5E629D, xmp.did:EE366F226EC6DF11A1DFE46A353D5FCB, uuid:64d6ed79-7b54-4b76-8626-8443a657bc89, xmp.did:E7C035091918E011A9FA8ACF743CAA68, xmp.did:173321AF4818E011A9FA8ACF743CAA68, xmp.did:133321AF4818E011A9FA8ACF743CAA68, xmp.did:C0F3276A24C8DF11A8C4CB9EBA2FB374, uuid:64d6ed79-7b54-4b76-8626-8443a657bc89, uuid:64d6ed79-7b54-4b76-8626-8443a657bc89, uuid:68ECE085E56BDE118BB9D29C546E964C, uuid:db9e253f-df6d-4cab-8ba2-a94c709a2b99, uuid:db9e253f-df6d-4cab-8ba2-a94c709a2b99, uuid:62ef20ba-977a-48f5-989a-983e00efdac1, xmp.did:DA185A08E818E0118937EA7B108C9D97, uuid:1BF6AC7E2A66DC119587E840D3F2AB0E, uuid:1EF6AC7E2A66DC119587E840D3F2AB0E, uuid:e9afb604-a48d-4f7f-908f-f23ad22a47b5, uuid:9df76112-0848-4e23-9a0a-9538338bdc15, uuid:c8b41fb0-053b-44c6-b42b-e2f6ce476905, uuid:63c622c8-4767-495c-8634-76a6d24a4e80, xmp.did:143321AF4818E011A9FA8ACF743CAA68, uuid:c0694680-63eb-4311-bd3c-5de3314ed2d0, uuid:de38fb24-abaf-4070-94bc-2c9937ac1465, uuid:3ae0fc29-c819-4cbb-9d3f-83575d02ac4f, xmp.did:23606E03C219E0119020C069EC9863B7, xmp.did:0A957C1BAF1DE0118448F6CD5BA1F697, xmp.did:0B957C1BAF1DE0118448F6CD5BA1F697, xmp.did:CA723AA0588FDF118A8B90AE2C49069C, uuid:9F54675EDA15DC1189C2BF8758B98E68
Doc Change Count                : 8119
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 30
EXIF Metadata provided by EXIF.tools

Navigation menu