Mipro Electronics Co 707HE Wireless Microphone User Manual ACT707D FCC

Mipro Electronics Co Ltd Wireless Microphone ACT707D FCC

Contents

User Manual 1 of 2

2CE128Z1- rack FrameZACT-functionZColor LCD PanelZDual 100 Preset ChannelsElectronics Co., Ltd.Head office: 814, Pei-Kang Road, Chiayi, 600, Taiwan.Taipei office: 5, Lane 118, Sung-teh Road, 100, Taipei, Taiwan.Web-http: //www.mipro.com.twE-mail: mipro@mipro.com.twInstruction ManualACT-Series Dual Channel Wireless Receiver ACT-Series Dual Channel Wireless Receiver
012-34-5667-13114151516-17171819151. INTRODUCTIONThanks for choosing the most advanced dual channel wireless receiver system from MIPRO.Please read this manual thoroughly for correct operating and optimal performance.ACT-707D is an international EIA standard, 1-rack, true diversity metal receiver. It features the world's first ACT-function, color LCD panel displaying multiple statuses. It allows rapid change of channels, offers non-interfering channel selection and eliminates spurious interference. Other unique features include a built-in switch-mode power supply, an antenna divider system and independent or mixed outputs. It's 1-rack, dual-channel design saves space and reduces installation time. Another great value system! The ideal choice for dual-channel receives in one rack space! Antenna 2 Instruction Manual 1 Power Cable 1 Rack-mount Brackets 1-pair Audio Output Cable 1 Included AccessoriesCONTENTS ACT DUAL CHANNEL WIRELESS RECEIVERACT DUAL CHANNEL WIRELESS RECEIVER1. INTRODUCTION2. PARTS NAME AND FUNCTIONS3. INSTALLATION OF THE RECEIVER5. CAUTIONSHANDHELD WIRELESS MICROPHONEBELT PACK TRANSMITTER1. PARTS NAME AND FUNCTIONS1. PARTS NAME AND FUNCTIONS2. BATTERY INSERTION4. BATTERY INSERTION3. OPERATING INSTRUCTIONS3. AF 4-PIN INPUT CONNECTION METHODS4. CAUTIONS5. CAUTIONS2. OPERATING INSTRUCTIONS6. OPERATION OF RECEIVER WITH LCD DISPLAY PANEL 194. RECEIVER OPERATING PROCEDURES
23ACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER2. PARTS NAME AND FUNCTIONSFront PanelRear Panel(Fig.1)(Fig.2)(1) Front Antenna A Input Connector : Allows an optional rear-to-front Antenna kit for front antenna placement. (2) Power Switch & Indicator: When switch is turned on, red indicator illuminates to denote normal power status.(3) Receiver Panel A : Color LCD Panel A.(4) Receiver Panel B : Color LCD Panel B.(5) Front Antenna B Input Connector : Allows an optional rear-to-front Antenna kit for front antenna placement. (6) Rear Antenna B input Connector: B Antenna connector can be installed with antenna directly and provides power for antenna booster..(7)(11) Balanced Audio Output Jack: With Cannon / XLR type connector provides balanced audio output signal from this jack to the amplifier.(8) Unbalanced Audio Mixed Output Jack : With 1/ 4 Phone Jack provides the mixed unbalanced audio output signal from this jack to the amplifier.(9) Unbalanced Level Switch: "MIC" selection is for "Microphone-level" output. "LINE" selection is for "Line-out" level output.(10) DC 12V Input Jack: To connect 12 VDC from the AC/DC adapter.(12) AC Input Jack: To connect 85 ~ 265 Volts AC power.(13) Rear Antenna A input Connector: A Antenna connector can be installed with antenna directly and provides power for antenna booster.(14) Rackmount Bracket: To install the receiver into an EIA 19-inch standard rack case.78 9 10 12 1311614MIC LINE2 3 4ACTMENURF AFGROUP CHANNELMHzTV CHG/CHVOLFREQ SQREMONAMEBATANTBAACTMENURF AFGROUP CHANNELMHzTV CHG/CHVOLFREQ SQREMONAMEBATANTBAACT-707D Wireless ReceiverONPOWERA B1 5
45(Fig.3)(Fig.4)3. INSTALLATION OF THE RECEIVER1. Install 2 separate antennas on the antenna sockets (6), (13) on the rear panel. Illustrated in figure 3.2. Power Output Connection:(a) Unbalanced Level Switch (9) Setting Position: When inputs the unbalanced output of a receiver into "AUX-IN" input jack of a mixer or amplifier or "Electric Guitar", switch the Level Switch (9) to the right "LINE" position. Low sensitivity may occur if switch to the wrong position. When input the unbalanced output of a receiver into the "MIC-IN" input jack of a mixer or amplifier; switch the Level Switch (9) to the left "MIC" position. Over load distortion may occur if switch to the wrong position. When using electric guitar, don't use "MIC" position as it may have generated insufficient level.(b) Unbalanced Output: Using audio output cable attached with "PHONE PLUG" type, connect one end from the unbalanced output jack (8) of the receiver, and the other end to the "LINE-IN" input jack of the amplifier, as shown in Fig. 3.(c) Balanced Output: Using audio output cables attached with "XLR" or "Cannon" type, connect one end from the balanced output jacks (7) of the receiver, and the other end to the "MIC IN" input jack of the mixer or amplifier, as shown in Fig. 3. (The characteristic of the 3-pin connector is as shown in Fig. 6(d) Guitar Output: Using audio output cable attached with "PHONE PLUG" type, plug one end from the unbalanced output jack of a receiver, and the other end to the input jack of a guitar amplifier. Switch the Level Switch (9) to "LINE" position.(Fig.6)3. Audio Output Connection:(a) Connect the AC/DC adapter cable to DC 12V INPUT JACK (10), then plug the adapter unit into an appropriate AC outlet with caution to the correct voltage under both AC outlet and adapter marked, as shown in fig. 4.(b) With the appropriate AC power cable connects from AC Input Jack (12) to an AC outlet under the marked voltage 85~265 V, as shown in Fig. 5.(Fig.5)3: COLD - - + +1: GND2: HOT321(Fig.8)(Fig.7)4. To ensure best reception possible, receiver must be installed at least one meter above ground. In addition, the distance between transmitter and receiver must be more than one meter and away from noise. (Shows in figure 7)5. On the front panel of the receiver, 4 openings are pre-drilled for instant installation on the standard 19-inch rack case. (Shows in figure 8)MIC LINEACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER
675. CAUTIONS1. When using DC power supply, please be aware of the operating voltage. First of all, please make sure minimum of 12 volts can be obtained for function properly. However, the power supply should not exceed its maximum capacity of 15 volts. When the supply voltage is more than 15 volts, the system will suffer severe internal damage. It is preferred the power source is from a regulated power with the minimum current of 1 A.2. Use only MIPRO standard antenna to ensure the sensitivity of the receiver.3. Antenna socket has 8-volts DC power supply; please do not short the circuit of this part.4. RECEIVER OPERATING PROCEDURES1. Turn volume controls of the mixer in use to a minimum setting before turn on the microphones or transmitters. After switches on the receiver, the power switch red indicator illuminates to denote normal power status.2. Under normal circumstances, the RF indicator lights up when a microphone or transmitter is turned on near the receiver to indicate the receiver is ready for normal operation. Once sounds to the microphone and the AF indicators will glow according to the strength of sound level. If no LED glows or no sound outputs, the system is not function properly, thus it must be checked3. The microphone output level needs to be adjusted at the amplifier or mixer. No need to adjust at the receiver itself. G/CH FREQ SQ VOL NAME REMOACTMENURFRF AFAFGROUPGROUP CHANNELCHANNELMHzMHzTV CHTV CHG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAACTMENURFRF AFAFGROUPGROUP CHANNELCHANNELTV CHTV CHG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAA2. Designations of buttons and FunctionsMENU: Enable user to select from one function to the other"MENU" button allows user to select among 6 options (in the sequence showing below) that each is surrounded in a square frame and shown on the upper half of LCD display. Detail functions and operations are as follows.(1) G/CH: Indicates or setups the receiver GROUP and CHANNEL.A. Operating Procedures.EXITG/CHMENU GROUPDOWN UPMENUCHANNELDOWN UPMENUSave6. Operation of Receiver with LCD Display Panel 1. Full Display of LCD Screen and Locations of buttonsACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER
8 9FREQMENUACTMENURFRF AFAFMHzMHzG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAACTMENURFRF AFAFG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAB. How to Operate?a. In the lower row of LCD display, TV CHANNEL, GROUP, and CHANNEL are separately shown in dual-digit numbers (from left to right).b. Push "UP" or "DOWN" button once and the number above "GROUP" will start blinking. Push "UP" or "DOWN" button now will permit user to change to another pre-programmed group. Push "MENU" button to confirm the modification and group number will stop blinking.(2) FREQ: Indicates the frequency that is currently in use.A. Operating Procedures.B. How to Operate?a. After push "MENU" button and select the "FREQ" frame, it will show the frequency that is set under the GROUP and CHANNEL that one had selected previously.b. This function cannot be used for frequency alternation.(3) SQ: Indicates or setups the Squelch level.RFRF AFAFG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAACTMENUVOLMENU MUTEDOWN UPEXITa. User can set the squelch level within the range of 01-99.b. To set the squelch level, simply by pushing the "UP" or "DOWN" button and confirm the modification by pushing "MENU" button.(4) VOL: Indicates Volume Level is at On or Mute position.SQMENU 01DOWN UPEXITMENUsaveA. Operating Procedures.B. How to Operate?Switching From Audible To MutePush "UP" or "DOWN" Button allows one to switch volume to "ON" or "Mute" status. A. Operating Procedures.B. How to Operate?AF bar and Ant. A, B of LCD panel will not displayed when the receiver module is at Mute status. To ascertain if receiver is at Mute status, press Menu key, select Volume. If LCD indicates "Mute" it is a Mute status. If LCD indicates "On" audio is operating normally.C. CAUTIONS : ACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER
10 11NAMEMENU ADOWN UPMENUNEXTEXITADOWN UPMENURFRF AFAFG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAACTMENU(5) NAME: Indicates or setups the name of current channel user.saveA. Operating Procedures.B. How to Operate?a. Maximum 6 characters are allowed (Select from capitalized English letter, numbers, + - x /, and space).b. Push "UP" or "DOWN" button into setup mode and the character on the far left will start blinking. (There will be no blinking if there is no character in the specific space).c. Push "UP" or "DOWN" button to select desired character and confirm by pushing the "MENU" button. Once confirmed, the next character will start blinking and ready for setup.d. Repeat step c until ALL 6 characters are set.ACTMENURFRF AFAFG/CHG/CHVOLVOLFREQFREQ SQSQREMOREMONAMENAMEBATBATANTANTBBAAACTACT EXITOperation of ACT Feature:A. Operating Procedures.B. How to Operate?a. At LCD panel displays "Group" and "Channel" mode keystroke "ACT" button . ACT mode is activated when "ACT" word appears on the LCD panel. b. Position the "ACT" marking of the transmitter about 30cm (12-inch) towards the "ACT" button on the receiver. (see below figure) c. ACT function will release automatically once the transmitter channel is locked on. Simultaneously, "Group" and "Channel" mode will be back showing on the LCD panel. ACTACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER
12 13NOTE NOTEACT DUAL CHANNEL WIRELESS RECEIVER ACT DUAL CHANNEL WIRELESS RECEIVER

Navigation menu