Mitsubishi Electric Inazawa Works 4D454C2D5001 Card Reader User Manual Users manual

Mitsubishi Electric Corporation Inazawa Works Card Reader Users manual

Users manual

YXN10-117* 1 Sep. 2010 Mitsubishi Access Control System MELSAFETY-P series Card reader Plane type UCR-8202A-P 1 Defend for safety. ································································································· 2 2 When using it 2-1 Attention in use ············································································ 3 2-2 What is the card reader?··························································· 6 2-3 Names and functions of each parts.····································· 8 3. Basic operation·····································································································12 ● Asking maters ● Please read this manual, and use it ahead of the use correctly and safely. Please keep it in the place where the person who uses it is always seen with enclosed "Guide of the Mitsubishi Electric Corporation repair window and the chat channel" after it reads. In general, the name of the company, the brand name, and the logo mark described in his manual are the trademarks or, registered rademarks of each company. ■Caution ・ Part or all of the content of this book will be refused and we refuse to reprint or to reproduce any shape hard without in our company the refusal. ・ It makes an effort as followed to the revision of software and hardware, and when it cannot synchronize unavoidably, the content of the description of this book is caused. Users manual
YXN10-117* 21 Defend for safety. ●It divides by the following display and it explains danger and the extent caused when wrong handling is done. 警告 The one with possibility of relating to death and serious illness, etc. when wrong handling is done 注意 誤った取扱いをしたときに傷害または家屋・家財などの損害に結びつくもの Prohibition Don't resolve or remodel it. It causes a fire, the electric shock, and the breakdown by the short and generation of heat. Prohibition Don't set up in a dusty place. It causes a fire, the electric shock, and the breakdown. Prohibition Don’t insert metallic things in the main body. It causes a fire, the electric shock, and the breakdown by the short and generation of heat. Please contact the nearest service office, if something enters the inside. Prohibition Don't set up in a humid place. It causes a fire, the electric shock, and the breakdown. Prohibition Don't wet it with water. It causes a fire, the electric shock, and the breakdown by the short and generation of heat. Please wipe off with the cloth when the drop of water attaches outside of the main body. Please contact the nearest service office when the drop of water enters the inside. Prohibition Don't set up in an unstable place or the place where a lot of vibrations exist. Prohibition Don’t damage the codes. It causes a fire, the electric shock, and the breakdown by the short and generation of heat. Please do not torture, and do not pull the code. Please contact the nearest service office when the code hurts by any chance. Prohibition Don't set up in the place where direct sunshine strikes. It causes fading when setting up in the place where direct sunshine strikes Prohibition Don’t allow something to hit. The hard one and an umbo are thrown, and it causes the breakdown of the equipment, and it causes a fire, the electric shock, and the breakdown by the short and generation of heat. Prohibition Don’t set up in outdoor. When setting it up in outdoor, dust or the drop, etc. enter the attestation device or in the electric lock control board, and it causes a fire, the electric shock, and the breakdown. ProhibitionEspecially, the installation in the place that becomes a high temperature is avoided. It is recommended to use it at 35℃ or less to operate it comfortably. Groud it. Ground the equipment to prevent the breakdown beforehand. (the third kind earth is rcommended)
YXN10-117* 32 When using it 2-1 Attention in use 2-1-1 Attention concerning use of device 1) Please read "Manual” of each equipment correctly and use it. 2) It is not the one to prevent the crime such as the thefts though this device controls an insertion leaving a room and an electric lock. Please acknowledge being not able to assume the responsibility at all even when an emergency accident and damage are caused. 3) Please intercept the breaker that supplies the power supply to a pertinent equipment when it smells abnormal from the equipment by any chance or it overheats and is smoking. 4) It doesn't assume the responsibility about the collateral damage due to the instrument fault. 5) It becomes impossible for it to become difficult to read for surroundings to include a metal, an electric equipment, and the power cable, etc. because the noncontact card reader is an equipment that used the electric wave, and to read. It is not greatly influenced for the electric wave (radio television inverters), and do not set up these things in the surrounding, please. 6) There is something that uses same frequency (13.56MHz) in medical equipment. It causes the malfunction when is to be near such medical equipment. 7) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 8) FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment. 9) Properly shielded and grounded cables and ferritic cores must be used for connection to controllers in order to meet FCC emission limits. 10) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
YXN10-117* 4 2-1-2 Attention concerning use of cards. The cards used with this system are contactless IC cards that contain electric parts (integrated circuit chip) in them. When the cards are bent or pressure is applied, the stress might hang in built-in electric parts and it cause the breakdown. Moreover, the resin material (vinyl chloride or PET) used for the surface of the card might be transformed by heat. Please note the following points to prevent the card being damaged. (1)Don’t bend or apply pressure. It might break off the cards. (2)Keep cards in the card cases (hard case) when you carry. (3)Avoid keeping cards in a purses or soft card cases. (they are easy to bend.) (4)Avoid keeping cards in the pocket. (5)Don’t drop card while using it (And, be keeping it). (6)Don’ t leave the card in the place (dashboard etc. of the car) that becomes a high temperature. (7)Use card one by one. Don’t use it with other cards. (8)Please do not carry the card to the following shop floors where the electromagnetical field is given to the card. Welding shop floor. Hallmark shop floor where it static electricity examines, and noise is examined Additionally, surrounding of power line, transformation installation, and mass motor that generates strong electromagnetical field etc. (9)Please inform the manager or the service office promptly when you lose the card. Antenna The antenna of the card is almost mounted onouter. The antenna might be disconnected bydamaging and the hole opening about the card. IC chip mounting part The encapsulant might do the crack by a partiabend and the impact though it is fixed with theencapsulant. Internal image of card
YXN10-117* 5 2-1-3 How to use The card is held up in parallel in the card reading part referring to the figure below. Please hold card one by one to enter (or exit) a room. card Card reader (side)Reading anntena Move it close from the front tothe center of the card readeruntil it beeps. Card reader (front) Move the card too fast or too slow, it may fails to read the card, and it beeps long, and the OK/NG lamp lights red. Please hold the card again. It might read completely.
YXN10-117* 62-2 What is the card reader? The card reader read the card data, and it compare them with the registered card data. And it controls the lock of the door. 2-2-1 Basic operation Item Explanation Reference Enter of exit a room with card Hold the card in front of the card reader to unlock the door. Note To use the card, it is necessary set them from management WEB. The registered card can be used with all doors connected with the same controler.
YXN10-117* 72-3 Names and functions of each parts 2-3-1 Card reader (Plane type) Name Function The collation result of the card is displayed. Succeed Green. ＬＥＤ（ＯＫ） Fail or Prohibited to use Red. Show state of lock Locked Green. Unlocked Red. ＬＥＤ（lock） Emergency unlock Flashing red. Read anntena Hold the card to be read Read anntena Lock ＯＫ ＬＥＤ(OK) ＬＥＤ(Lock)

Navigation menu