Mitsubishi Electronics Digital Electronic Accessory Q02Cpu Users Manual User's Manual(Hardware Design, Maintenance And Inspection)

2015-02-09

• COVER
• SAFETY PRECAUTIONS
• REVISIONS
• INTRODUCTION
• CONTENTS
• About Manuals
• How to Use This Manual
• About the Generic Terms and Abbreviations
• 1 OVERVIEW
  • 1.1 Features
• 2 SYSTEM CONFIGURATION FOR SINGLE CPU SYSTEM
  • 2.1 System Configuration
  • 2.2 Precaution on System Configuration
  • 2.3 Confirming the Serial Number and Function Version
• 3 GENERAL SPECIFICATIONS
• 4 HARDWARE SPECIFICATION OF THE CPU MODULE
  • 4.1 Performance Specification
  • 4.2 Part Names and Settings
  • 4.3 Switch Operation After Writing in Program
  • 4.4 Latch Clear Operation
  • 4.5 Executing Automatic Write to Standard ROM.
• 5 POWER SUPPLY MODULE
  • 5.1 Specification
    • 5.1.1 Power supply module specifications
    • 5.1.2 Selecting the power supply module
    • 5.1.3 Precaution when connecting the uninterruptive power supply
  • 5.2 Names of Parts and Settings
• 6 BASE UNIT AND EXTENSION CABLE
  • 6.1 Base Unit Specification Table
  • 6.2 Extension Cable Specification Table
  • 6.3 Parts Names of Base Unit
  • 6.4 Setting the Extension Base Unit
  • 6.5 I/O Number Allocation
  • 6.6 Guideline for Use of Extension Base Units (Q5[ ] B)
• 7 MEMORY CARD AND BATTERY
  • 7.1 Memory Card Specifications
  • 7.2 Battery Specifications (For CPU Module and SRAM Card)
  • 7.3 Handling the Memory Card
  • 7.4 The Names of The Parts of The Memory Card
  • 7.5 Memory Card Loading/Unloading Procedures
  • 7.6 Installation of Battery (for CPU Module and Memory Card)
• 8 EMC AND LOW VOLTAGE DIRECTIVE
  • 8.1 Requirements for Conformance to EMC Directive
    • 8.1.1 Standards applicable to the EMC Directive
    • 8.1.2 Installation instructions for EMC Directive
    • 8.1.3 Cables
    • 8.1.4 Power supply module
    • 8.1.5 When using QA1S6[ ] B type base unit
    • 8.1.6 Others
  • 8.2 Requirement to Conform to the Low Voltage Directive
    • 8.2.1 Standard applied for MELSEC-Q series PLC
    • 8.2.2 MELSEC-Q series PLC selection
    • 8.2.3 Power supply
    • 8.2.4 Control box
    • 8.2.5 Grounding
    • 8.2.6 External wiring
• 9 LOADING AND INSTALLATION
  • 9.1 General Safety Requirements
  • 9.2 Calculating Heat Generation by PLC
  • 9.3 Module Installation
    • 9.3.1 Precaution on installation
    • 9.3.2 Instructions for mounting the base unit
    • 9.3.3 Installation and removal of module
  • 9.4 How to Set Stage Numbers for the Extension Base Unit
  • 9.5 Connection and Disconnection of Extension Cable
  • 9.6 Wiring
    • 9.6.1 The precautions on the wiring
    • 9.6.2 Connecting to the power supply module
• 10 MAINTENANCE AND INSPECTION
  • 10.1 Daily Inspection
  • 10.2 Periodic Inspection
  • 10.3 Battery Replacement
    • 10.3.1 Battery life
    • 10.3.2 Battery replacement procedure
• 11 TROUBLESHOOTING
  • 11.1 Troubleshooting Basics
  • 11.2 Troubleshooting
    • 11.2.1 Troubleshooting flowchart
    • 11.2.2 Flowchart for when the "MODE" LED is not turned on
    • 11.2.3 Flowchart for when the "MODE" LED is flickering
    • 11.2.4 Flowchart for when the "POWER" LED is turned off
    • 11.2.5 Flowchart for when the "RUN" LED is turned off
    • 11.2.6 When the "RUN" LED is flickering
    • 11.2.7 Flowchart for when the "ERR." LED is on/flickering
    • 11.2.8 When the "USER" LED is turned on
    • 11.2.9 When the "BAT." LED is turned on
    • 11.2.10 Flowchart for when the "BOOT" LED is flickering
    • 11.2.11 Flowchart for when output module LED is not turned on
    • 11.2.12 Flowchart for when output load of output module does not turn on
    • 11.2.13 Flowchart for when unable to read a program
    • 11.2.14 Flowchart for when unable to write a program
    • 11.2.15 Flowchart for when it is unable to perform boot operation from memory card
    • 11.2.16 Flowchart for when UNIT VERIFY ERR. occurs
    • 11.2.17 Flowchart for when CONTROL BUS ERR. occurs
  • 11.3 Error Code List
    • 11.3.1 Procedure for reading error codes
    • 11.3.2 Error Code List
  • 11.4 Canceling of Errors
  • 11.5 I/O Module Troubleshooting
    • 11.5.1 Input circuit troubleshooting
    • 11.5.2 Output Circuit Troubleshooting
  • 11.6 Special Relay List
  • 11.7 Special Register List
• APPENDICES
  • APPENDIX 1 Error Code Return to Origin During General Data Processing
    • APPENDIX 1.1 Error code overall explanation
    • APPENDIX 1.2 Description of the errors of the error codes (4000H to 4FFFH)
  • APPENDIX 2 External Dimensions
    • APPENDIX 2.1 CPU module
    • APPENDIX 2.2 Power supply module
    • APPENDIX 2.3 Main base unit
    • APPENDIX 2.4 Slim type main base unit
    • APPENDIX 2.5 Extension base unit
  • APPENDIX 3 Upgraded Functions of High Performance Model QCPU
    • APPENDIX 3.1 Specification comparison
    • APPENDIX 3.2 Function comparison
    • APPENDIX 3.3 Added functions and the corresponding GX Developer versions
• INDEX
• WARRANTY