Mobile Technologies 165-00471 Power Distribution Unit User Manual

Merchandising Technologies Inc. Power Distribution Unit

UserManual.wiki >

Mobile Technologies >

165 00471 User Manual HTML Version

User Manual

SECURE PLUG™ (PATENT PENDING) USER GUIDE

Product Manual for

SECURE PLUG™

DO NOT REMOVE FROM STORE

Contents

1. Materials in Box 2

2. Installation 3

3. Key Whitelist 4

4. Merchandising 5

5. Arming & Disarming the System 7

6. Remerchandising 8

7. Adding New User Keys 8

8. Deleting Whitelist 8

9. LED Status Indicators 9

10. FCC and ISED Statement 12

For additional support, please reach out to our

Contact Center at 800-426-6844

CONTENTS

SECURE PLUG™ (PATENT PENDING) USER GUIDE

MATERIALS IN BOX

Remote Access Module (Optional)

Alarm Label Sheet

Secure Plug Power Strip (Region-Speciﬁc)

SECURE PLUG™ (PATENT PENDING) USER GUIDE

INSTALLATION

The Remote Access Module allows you to use the RFID cards to

control the Secure Plug when access to the unit is difﬁcult.

IF USING THE REMOTE ACCESS MODULE: Plug in to

the end of the Power Strip and afﬁx to surface, if desired.

Plug Power Strip into a wall outlet.

FOR SCREW MOUNT (OPTIONAL): Use three #6 wood screws (not included). Measure and install screws into mounting

surface leaving 1/4” of the screw heads exposed. Align the Power Strip keyholes (circled in blue) and hang onto the screws.

WARNING: No user serviceable parts inside. Please contact MTI for service.

CAUTION: To Reduce the Risk of Electric Shock – Use Only Indoors.

CAUTION: Risk of Electric Shock. Do not plug into another relocatable power tap or an extension cord.

CAUTION: Use Only in Dry Locations.

AVERTISSEMENT: Aucune pièce réparable par l’utilisateur à l’intérieur.

Veuillez contacter MTI pour le service.

ATTENTION: Pour réduire le risque de choc électrique - Utiliser uniquement à l’intérieur.

ATTENTION: Risque de choc électrique. Ne pas brancher sur une autre alimentation ou une rallonge.

ATTENTION: Utiliser uniquement dans des endroits secs.

2.4 in

(62 mm)

7.9 in

(200 mm)

1.6 in

(42 mm)

SECURE PLUG™ (PATENT PENDING) USER GUIDE

KEY WHITELIST

Place Authorization Card over the RFID icon to register to

system. LED will be solid blue.

The whitelist process can be done on the Secure

Plug unit or through the Remote Access Module.

Place the User Key over the RFID icon you want to add.

If successful Æ unit beeps 2 times

If unsuccessful Æ unit beeps 4 times (retry)

Repeat process for all User Keys until they are

successfully added.

To close the whitelist mode, place the Authorization Card

over the RFID icon. Whitelist mode will end automatically

after 3 minutes of no use. LED will be ﬂashing white.

Plug in product cables one at a time to the Power Strip.

If successful Æ 2 beeps and LED will be solid green,

this may take 20 to 60 seconds for products with larger

power adapters. The Remote Access Module will show a

corresponding white LED for that socket port.

If unsuccessful Æ unit beeps 4 times and LED will be solid

red. The Remote Access Module will show a corresponding

red LED for that socket port. Unplug cable from the Power

Strip and try again making sure cables are unplugged from

the product.

Unplug any cables from the product end for products that have removable power cords. If the product does not have a

removable power cord, turn the power to the product to OFF.

NOTE: Only supports

products up to 10A.

SECURE PLUG™ (PATENT PENDING) USER GUIDE

MERCHANDISING

3Repeat steps with next product to merchandise.

When all products have been successfully setup, plug cables back into product end at this time. Apply an “Alarm” label to

product end of cable, if desired.

Turn the power to products with a detachable power adapter to ON at this time. Keep power to other products OFF (ie.

hardwired products or products without power adapters).

SECURE PLUG™ (PATENT PENDING) USER GUIDE

MERCHANDISING

SECURE PLUG™ (PATENT PENDING) USER GUIDE

Place any User Key over the RFID icon and the LED

will change from ﬂashing white to solid white to indicate

Armed.

Turn the power to products to ON or OFF at this time, as

desired.

If any cable becomes unplugged, the system will alarm.

LED will ﬂash red/white. The Remote Access Module will

show a corresponding red LED for that socket port.

To re-arm, ﬁx the issue by plugging all cables back in. Place a User Key over the RFID icon and the LED will be solid white.

Placing a User Key over the RFID icon will silence the

alarm. The LED will remain ﬂashing red/white.

ARMING/DISARMING THE SYSTEM

1a 1b

SECURE PLUG™ (PATENT PENDING) USER GUIDE

DELETING WHITELIST (This will delete all User Keys from the system.)

ADDING NEW USER KEYS

REMERCHANDISING

From an Armed state, place the User Key over the RFID

icon to disarm the system. LED will be ﬂashing white.

From an Armed state, place the

User Key over the RFID icon to

disarm the system. LED will be

ﬂashing white.

Place Authorization Card over the RFID icon. Follow Key

Whitelist process starting on page 4.

Merchandise a new product by

following the process on page 5.

If you did not unplug a product,

there is no need to remerchandise

the product again.

From an Alarming state, place the

User Key over the RFID icon to

silence the alarm. Then hold down

the User Key for 5 seconds to

return back to the disarmed state.

LED will be ﬂashing white.

From an Armed state, place the

User Key over the RFID icon to

disarm the system. LED will be

ﬂashing white.

Hold down the Authorization Card

for 5 seconds, LED will be solid

yellow.

Place the Authorization Card over

the RFID icon AGAIN while LED is

yellow.

If successful Æ unit beeps 2 times

and the LED will turn solid green

If unsuccessful Æ unit beeps 4

times (retry)

SECURE PLUG™ (PATENT PENDING) USER GUIDE

LED STATUS INDICATORS

Visual Reference System Status Condition Solution

LED is solid white. Armed System is armed.

LED is ﬂashing white. 1. Disarmed

2. Merchandising Calibration

1. System is disarmed and needs to be re-

armed.

2. System is calibrating product, wait until

successful or unsuccessful merchandising

before proceeding.

LED is ﬂashing red and white. Alarm System is alarming and needs to be

attended to.

LED is ﬂashing red. Mains Power Loss

Mains power loss has occurred. System

will alarm for 5 minutes. Whitelist

and merchandising information will be

maintained upon restoration of power.

LED is solid red. Merchandising Unsuccessful If merchandising fails, unplug the product.

Follow merchandising process again.

SECURE PLUG™ (PATENT PENDING) USER GUIDE

Visual Reference System Status Condition Solution

LED is solid green. Ready to Whitelist

System has an Authorization Card, but does

not have any User Keys added. Follow key

whitelist process.

LED is ﬂashing green. Factory Reset System has no whitelist or Authorization

Card. Follow key whitelist process.

LED is solid blue.

1. Whitelist Mode (if using

Authorization Card)

2. Overcurrent

1. System is in whitelist enrollment mode.

Follow whitelist process to add User Keys.

2. System has gone into overcurrent

protection. Unplug any product which

may be drawing too much power.

LED is ﬂashing blue. Overcurrent/Disarmed

System has gone into overcurrent protection

and user has disarmed the system. Unplug

any product which may be drawing too

much power. The system will self-heal.

LED is ﬂashing yellow.

1. Ready to be Armed without

MTI Connect Mesh Connected

2. Merchandising Calibration

without MTI Connect Mesh

Connected

1. Add Secure Plug unit to Mesh network.

2. System is calibrating product, wait until

successful or unsuccessful merchandising

before proceeding.

LED is solid yellow.

1. Armed without MTI Connect

Mesh Connected

2. Delete Whitelist Mode (If using

Authorization Card)

1. Add Secure Plug unit to

Mesh network.

2. System is deleting whitelist. Wait until

complete.

LED STATUS INDICATORS

SECURE PLUG™ (PATENT PENDING) USER GUIDE

Visual Reference System Status Condition Solution

Individual LED is solid white

(not main LED)

Merchandising successful for

that socket port See main LED for overall system status.

Individual LED is solid red

(not main LED)

1. Merchandising unsuccessful

for that socket port

2. Alarm

1. If merchandising fails, unplug the

product. Follow merchandising process

again.

2. System is alarming on corresponding

socket port and needs to be attended to.

See main LED for overall system status

LED is ﬂashing blue. 1. Provisioning Mode

2. Overcurrent/Disarmed

1. System has entered Mesh network

provisioning mode. If it’s within range

of a Hub that is also in provisioning

mode, it will join the Hub’s network

within 5 seconds and it will stop

ﬂashing blue.

2. System has gone into overcurrent

protection and user has disarmed the

system. Unplug any product which

may be drawing too much power. The

system will self-heal.

LED is ﬂashing multiple colors.

System has received an

“identify” command from a user

of the MTI Connect software.

LED STATUS INDICATORS

SECURE PLUG™ (PATENT PENDING) USER GUIDE

FCC AND ISED STATEMENT

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage

est susceptible de compromettre le fomctionnement du dispositif.

CAN ICES-3(B)/NMB-3(B)

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain

Canadian information on RF exposure and compliance.

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf,

utilisateurs peut obtenir l’information canadienne sur l’exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated

with a minimum distance of 20 millimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et

actionné avec une distance minimum de 20 millimètres entre le radiateur et votre corps.

MTI declares that the radio equipment models 165-00460, 165-00470 and 165-00471 Secure Plug Power distribution units including the

models 165-00645 and 165-00670 Remote Access Modules in compliance with EU Directive 2014/53/EU.

The full text of the EU Manufacturer’s Declaration of Conformity is available at the following internet address: www.mobiletechinc.com

This device complies with Part 15 of the FCC Rules.

Caution: If any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

The grantee is not responsible for any changes or modiﬁcations not expressly approved by the party responsible for compliance. Such modiﬁcations could

void the user’s authority to operate the equipment.

The RF Exposure Compliance distance is 20 millimeters.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Technical Data

Model: 165-00471

Operating Frequency: 125KHz

Operating Temperature: 0° C to 40° C

Max Power: 125KHz: <42dBuA/m at 10m

Technical Data

Model: 165-00645 / 165-00670

Operating Frequency: 125KHz, 2.4GHz: 2405-2480MHz

Operating Temperature: 0° C to 40° C

Max Power: 125KHz: <42dBuA/m at 10m

2.4GHz: <20dBm

FCC ID: 2AA2X-165-ØØ471

Model: 165-00471

FCC Statement

FCC ID: 2AA2X-165-ØØ645-24

Model: 165-00645 / 165-00670

FCC Statement

ISED Certifcation Number: 24439-165ØØ471

Model: 165-00471

ISED Statement

ISED Certifcation Number: 24439-165ØØ64524

Model: 165-00645 / 165-00670

ISED Statement

Merchandising Technologies Inc.

Unit B, 9/F., Great Wall Factory Building 11 Cheung Shun Street,Lai Chi Kok,Kowloon, Hongkong

Mobile Technologies 165-00471 Power Distribution Unit User Manual

Merchandising Technologies Inc. Power Distribution Unit

User Manual

Navigation menu

Namespaces

Views

Navigation