Mobiletron Electronics NXP002 TPMS User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3821564
Application ID	YlO5EO+49Mx0+s/UD+T88A==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.27kB (540854 bits)
Date Submitted	2018-04-19 00:00:00
Date Available	2018-04-20 00:00:00
Creation Date	2018-03-27 13:53:36
Producing Software	Microsoft® Word 2010
Document Lastmod	2018-03-27 13:53:36
Document Title	Users Manual
Document Creator	Microsoft® Word 2010
Document Author:	Jason.Shih[施仁元]

TPMS_TX
TX026 User's Manual
Specification
Frequency
433.92 MHz
Pressure Range
100~1500 kPa
Temperature Range
-40 ~125℃
Operating Humidity
Max. 95%
Operating Temperature
-40 ~105℃
Storage Temperature
-40 ~125℃
Mounting the Tire with Transmitter on Wheel Rim
1. Fasten Transmitter on the Wheel Rim
1st.
Pass Clamping Strap through Transmitter。
2nd.
Position the Transmitter in the lowest area of the
concave center well near the valve。
Valve
Transmitter
Note：It is recommended that the location of each transmitter be
recorded to avoid possible damage when tires need to be
removed。
3rd.
Attach the Clamping Strap end to the clamp by
advancing the Worm Gear Clamp with a socket driver
or screwdriver ； tighten the Clamping Strap until
secured.。
Note：Position Worm Gear Clamp opposite to Transmitter for
better tire rebalancing。
4th.
Cut excess Clamping Strap off to approximately one
inch (25mm) from Worm Gear Clamp with a Cutter；
remove burrs from Clamping Strap end。
Position Worm Gear
Clamp Opposite to
Transmitter
Valve
1. Assemble Tire
2. Assemble Tire
1st.
Place tire under Transmitter as shown below。
Place Tire
Changing
Machine’s Lever to
Valve
the Opposite Side
of Valve
Use auto-install machine to install the lower-side of tire
onto rim。
2nd.
Valve
Turn in This
Direction Slowly
3rd.
Place the upper-side of tire onto rim。
Notice：turn slowly by machine to force down the wall of tire。
Tire Changing
Machine’s Lever Has
to Come to a Stop
Before Valve to
Ensure It Won’t Touch
Nearby Transmitter
Turn
in
This
Direction Slowly
Valve
4th.
Install whole tire to the wheel。
Place Tire Lever to
Tire
the Opposite Side of
Tire Changing Lever
(Contrasting
to
Valve) to Protect
Nearby Transmitter
Changing
Machine’s Lever
Valve
4.1 Removing tire with the transmitter Inside
Caution:：
The transmitter devices should be removed by a qualified technician。
The removal
directions must be followed to ensure that the
transmitters are undamaged。
1. Remove Valve Cap and Deflate Air Completely
Screw valve cap out of valve and let air discharge completely；
remove balancing weight/s；press tire off the safety shoulder
inside and outside。
Location of
Transmitter
Within Tire
Tire
Changing
Machine’s Lever
Valve
Location of
Transmitter
Within Tire
Tire
Changing
Machine’s Lever
Valve
Caution: In order not to damage the transmitter，Tire Level should be placed in
the opposite side of valve。
2. Removing the tire from the rim
1st.
Place tire onto the installation machine；rub soapy
water onto tire bead and rim lip。
Tire
Changing
Machine’s Lever
Valve
Tire Lever
Location of
Transmitter
Within Tire
2nd.
Place the machine Tire Lever on the tire bead and lift
tire bead with a manual Tire Lever over the installation
head and pull tire away。
Tire
Changing
Machine’s Lever
Manual Tire Lever
Location of
Transmitter
Within Tire
Tire
Changing
Machine’s Lever
Manual Tire Lever
Turn
in
This
Direction Slowly
3rd.
Utilize Manual Tire Lever，simultaneously with Tire
Changing Machine’s Lever，to pull the lower tire bead
away from upper side of wheel。
Turn in This
Direction
Slowly
Transmitter
Manual Tire Lever
4th.
Remove the Transmitter from the rim。
FCC Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void
the user's authority to operate the equipment.
RF exposure warning:
The equipment complies with FCC RF exposure limits set forth for an uncontrolled
environment.
The equipment must not be co-located or operating in conjunction with any other antenna or
transmitter.
This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body. It could be removed.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
Language                        : zh-TW
Tagged PDF                      : Yes
Author                          : Jason.Shih[施仁元]
Creator                         : Microsoft® Word 2010
Create Date                     : 2018:03:27 13:53:36+08:00
Modify Date                     : 2018:03:27 13:53:36+08:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools