Molex CVS Dabendorf USA-MMC-DC Compenser USA-MMC-DC User Manual BA DC 070706
Novero Dabendorf GmbH Compenser USA-MMC-DC BA DC 070706
Manual
Funkwerk Dabendorf GmbH FCC ID: RK7USA-MMC-DC
Maerkische Strasse IC: 4774A-USAMMCDC
D-15806 Dabendorf
Germany
Page 1 of 4 pages
850 / 1900 MHz DUAL BAND COMPENSER
MODEL USA-MMC-DC 205 0111 1
USER MANUAL
1 GENERAL
The 850 / 1900 MHz Dual Band Compenser model USA-MMC-DC 205 0111 1 is a bi-directional,
dual band RF amplifier used in conjunction with either a dual band or a standard single band mobile
phone. It’s designed to compensate for signal attenuation in both transmit and receive paths due to
cable losses employed in automotive OEM installations. This helps to improve call quality in weak
coverage areas and reduce dropped calls in between cell sites. The Compenser is designed for digital
(GSM/GPRS, W-CDMA, EDGE and CDMA) modes.
WARNING
The Compenser must NOT be used for TDMA and/or the analog (AMPS) mode!
STATEMENT according to FCC rules CFR, Title 47, Part 15, Section 15.19:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause unde-
sired operation.
Funkwerk Dabendorf GmbH FCC ID: RK7USA-MMC-DC
Maerkische Strasse IC: 4774A-USAMMCDC
D-15806 Dabendorf
Germany
Page 2 of 4 pages
2 INSTALLATION
To meet the FCC’s and IC’s RF Exposure Guidelines, the antenna should be installed so there is at
least 20 cm of separation between the body of the user or nearby persons and the antenna. The antenna
must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING
All installations are done at the OEM factory. No end-user installation or accessible part is involved.
Any unauthorized changes or modifications not expressly approved by the party responsible for
compliance could void user’s authority to operate this equipment.
3 I/O CONNECTION
Mobile port: FAKRA RF type connector, cod. D, female
Antenna port: FAKRA RF type connector, cod. D, male
DC input and On/Off control: 4-pin automotive connector
4 SPECIFICATIONS
FCC ID RK7USA-MMC-DC
FCC Rule Parts 22H & 24E
IC Certification Number 4774A-USAMMCDC
IC Radio Standards Specification RSS-129 for 850MHz CDMA
RSS-132 for 850MHz GSM/GPRS, EDGE and
W-CDMA
RSS-133 for 1900MHz GSM/GPRS, EDGE,
W-CDMA and CDMA
Operating Frequency Uplink (Tx) 824 … 849 MHz
& 1850 … 1910 MHz
Downlink (Rx) 869 … 894 MHz
& 1930 … 1990 MHz
Funkwerk Dabendorf GmbH FCC ID: RK7USA-MMC-DC
Maerkische Strasse IC: 4774A-USAMMCDC
D-15806 Dabendorf
Germany
Page 3 of 4 pages
Mode of Transmission Digital
Data Source External
Type of Modulation GSM/GPRS, W-CDMA, EDGE, CDMA (digital)
Type of Information Telephony & Data
Input and Output Impedance 50 Ohms
Harmonics & Spurious according to FCC and IC specifications
Stability Any RF load condition
DC Supply Voltage 10.8 … 15.6 V
Current Draw (switched off) 0.1mA
OFF
I≤
Current Draw (quiescent) 140 mA 220 mA
Q
I≤≤
Current Draw (peak) 2.0 A
p
I≤
Operating Temperature: -20 … 55 C (-4 … 131 °F)
Storage Temperature: -40 … 90 C (-40 … 194 °F)
Maximum Output Power:
Modulation
Type Frequency Range
/MHz Emission
Designator max. Output Power
/Watts max. Output Power
/dBm
824.2 … 848.8 244KGXW 1.384 31.41 GSM/GPRS
1850.2 … 1909.8 245KGXW 0.908 29.58
826.6 … 846.4 4M18F9W 0.428 26.31 W-CDMA
1852.6 … 1907.4 4M15F9W 0.590 27.71
824.2 … 848.8 245KG7W 1.820 32.6 EDGE
1850.2 … 1909.8 245KG7W 0.951 29.78
824.7 … 848.31 1M27F9W 0.855 29.32 CDMA
1851.25 … 1908.75 1M29F9W 0.769 28.86
Table 1: Maximum Output Power
Power Output listed in Table 1 is conducted.
Funkwerk Dabendorf GmbH FCC ID: RK7USA-MMC-DC
Maerkische Strasse IC: 4774A-USAMMCDC
D-15806 Dabendorf
Germany
Page 4 of 4 pages
The antenna installation and operating configurations of this Compenser, including antenna gain and
cable loss must satisfy MPE categorical Exclusion Requirements of FCC Rules CFR (Code of Federal
Regulations) Title 47, Part 2, §2.1091. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-located or opera-
ting in conjunction with any other antenna or transmitter. Users and installers must be provided with
antenna installation instructions and transmitter operating conditions for satisfying RF exposure com-
pliance.