Montage Technology M88WI6000SIP M88WI6000 WiFi Module User Manual MWI042A Module

Download:
Mirror Download [FCC.gov]
Document ID	2589852
Application ID	pMjSfI/SN5oLHrML+8maFQ==
Document Description	Module Specification
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.13kB (289079 bits)
Date Submitted	2015-04-20 00:00:00
Date Available	2015-09-30 00:00:00
Creation Date	2015-04-15 20:49:27
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2015-04-15 20:49:27
Document Title	MWI042A Module
Document Creator	Microsoft® Office Word 2007
Document Author:	Scoot

MWI042A Module
M88WI6xxx Wi-Fi SoC module
Version: MWI042A
Date: 2015/3/2
MWI042A Module
1.1 Introduction
The M88WI6xxx is a stand-alone SoC Wi-Fi module providing fully integrated
2.4GHz 802.11 b/g/n radio.It also provides flexible peripheral interfaces such as
USB2.0,Ethernet PHY,PCM,RMII Interface,SDIO,JTAG,PWM,UART,I2C,ADC,
GPIO to connect various peripheral interfaces directly to the M88WI6xxx Wi-Fi
module.
1.2 Block Diagram
Interface
USB 2.0
Ethernet PHY
Interface
PCM
RMII Interface
802.11n
1T1R
2.4GHz
RF
802.11n
1T1R M88WI6032D/
MAC
M88WI6008S
BB
SDIO
JTAG
LED
(WAN/LAN/WiFi)
PWM
UART
I2C
ADC
GPIO
1.3 Features
*power supply +3.3VDC
*USB 2.0 Host
*Ethernet PHY Interface
*PCM
*RMII Interface
*SDIO
*JTAG
*LED x3(LAN/WAN/WIFI)
*PWM
*UART
*I2C
*ADC
MWI042A Module
*GPIO
*1x1 modes.
*150Mhz PHY Rate Support.
*20Mhz/40Mhz channel bandwidth.
*Multiple BSSID
*QoS-WMM,WMM Power Save
1.4 Pin Description
Table 1-1 shows a detailed pin functional description of module MWI042A.
Figure 1-1 MWI042A Pin Assignment Diagram
MWI042A Module
Type
Description
Input pin
Output pin
I/O
Bidirectional input/output
Power
Pin No.
Label
Ty
Description
pe
SYSTEM_CLK_40M
Clock output pin for 40Mhz.
2,5,8,16,
17,21,28,
DGND
These pins should be connected to
ground plane.
USB_DM
I/O
USB data pin Data‐
USB_DP
I/O
USB data pin Data+
EPHY_RX_IN
Ethernet PHY RX differential input
EPHY_RX_IP
Ethernet PHY RX differential input
EPHY_TX_ON
Ethernet PHY TX differential output
10
EPHY_TX_OP
Ethernet PHY TX differential output
11
GPIO14/PCM0_TXD/
P1_CRSDV_EXT
I/O
GPIO14 or PCM data output signal
or RMII CRSDV
12
GPIO15/PCM0_RXD/
P1_RXD_EXT0
I/O
GPIO15 or PCM data input signal
or RMII RXD0
13
GPIO16/PCM0_FS/
P1_RXD_EXT1
I/O
GPIO16 or PCM frame sync signal
or RMII RXD1
14
GPIO17/PCM0_BCLK/
I/O
GPIO17 or PCM bit clock signal
30,37,38,
50,53,54
P1_RMII_CLK_EXT
15
GPIO18/PCM0_MCLK/
or RMII Clock
I/O
P1_TXEN_EXT
18,19,22,
GPIO18 or PCM master clock signal
Or RMII TXEN
D3V3
Digital 3.3 V power supply
20
VDD_REGSDIO
Regulator output for SDIO card
23
SDIO_D0/GPIO24
I/O
SDIO data or GPIO24
24
SDIO_D1/GPIO25/MDC
I/O
SDIO data or GPIO25
34,35,36,
49
MWI042A Module
25
SDIO_D2/GPIO26/MDIO
I/O
SDIO data or GPIO26
26
SDIO_D3/GPIO27
I/O
SDIO data or GPIO27
27
SDIO_CMD/GPIO2
I/O
SDIO command signal or GPIO2
29
SDIO_CLK/GPIO3
I/O
SDIO clock signal or GPIO3
31
SDIO_WP/GPIO4
I/O
SDIO write protection signal or GPIO4
32
SDIO_CD/GPIO5
I/O
SDIO card detection signal or GPIO5
33
GPIO6
I/O
GPIO6
39
JTAG_TDI
JTAG data input
40
JTAG_TDO
JTAG data output
41
JTAG_TMS
JTAG mode select
42
JTAG_TCK
JTAG clock
43
LAN_LED/GPIO7
I/O
LAN activity LED or GPIO7
44
WAN_LED/GPIO8
I/O
WAN activity LED or GPIO8
45
WIFI_LED/GPIO9
I/O
WIFI activity LED or GPIO9
46
PWM_OUTa/GPIO10
I/O
PWM driver output A or GPIO10
47
PWM_OUTb/GPIO11
I/O
PWM driver output B or GPIO11
48
GPIO12/ROM1_CS_OUT
I/O
GPIO12 or ROM chip select
51
UART_RXD/I2C_SCLK
UART RX data input or I2C master
serial clock line
52
UART_TXD/I2C_SDA
I/O
UART TX data input or I2C master
serial clock line
55
ADC_I0
General purpose ADC input 0
56
ADC_I1
General purpose ADC input 1
57
RESET_N
Power on reset pin. Low Active.
Table 1-1
MWI042A Module
2. Hardware Introduction
2.1 Top View
2.2 Electronic Specification
Model Name
Product Name
WLAN 11n Wi-Fi SoC module
Standard
802.11b/g/n, 802.3, 802.3u
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of
150Mbps
Modulation Method
BPSK/ QPSK/ 16-QAM/ 64-QAM
Frequency Band
2.4GHz ISM Band
Spread Spectrum
RF Output Power
IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) IEEE
802.11g/n:OFDM (Orthogonal Frequency Division Multiplexing)
802.11b:17 dBm +/-1.5dBm(11Mbps)
802.11g:14 dBm +/-1.5dBm(54Mbps)
802.11n @2.4GHz:14dBm +/-1.5dBm(HT20 MCS7)
MWI042A Module
802.11n @2.4GHz:14 dBm +/-1.5dBm(HT40 MCS7)
Operation Mode
AP mode, Station mode
802.11b: 1M -91dBm +/-1.5dBm
802.11b: 2M -89dBm +/-1.5dBm
Receiver Sensitivity
802.11g: 54M -70dBm +/-1.5dBm
802.11n@2.4GHz:HT20 MCS7 -67dBm +/-1.5dBm
802.11n@2.4GHz:HT40 MCS7 -65dBm +/-1.5dBm
LED
WAN/LAN/WIFI
Security
WEP, TKIP, AES, WPA, WPA2
Supply Voltage
3.3V+-10%
Power Consumption
TX peak:400mA,RX peak:300mA(D3V3=3.3V)
Operating Temperature 0 – 70° C ambient temperature
Dimension
40.83x34.7x1.0mm (LxWxH)
MWI042A Module
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following
two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
This Transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
MWI042A Module
Only those antennas with same type and lesser gain filed under this FCC ID number can be
used with this device.
The final system integrator must ensure there is no instruction provided in the user manual
or customer documentation indicating how to install or remove the transmitter module.
Required end product labeling:
Any device incorporating this module must include an external, visible, permanent
marking or label which states: “Contains FCC ID: 2AEDFM88WI6000SIP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 9
Language                        : zh-TW
Title                           : MWI042A Module
Author                          : Scoot
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2015:04:15 20:49:27+08:00
Modify Date                     : 2015:04:15 20:49:27+08:00
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools