Motorola Solutions 89FT3844 Paging transmitter for MURS User Manual

Motorola Solutions, Inc. Paging transmitter for MURS Users Manual

Users Manual

Download: Motorola Solutions 89FT3844 Paging transmitter for MURS User Manual
Mirror Download [FCC.gov]Motorola Solutions 89FT3844 Paging transmitter for MURS User Manual
Document ID3757563
Application IDp+1L5s7AD+VTOGaVUzkTBw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize78.85kB (985629 bits)
Date Submitted2018-02-21 00:00:00
Date Available2018-02-23 00:00:00
Creation Date2018-02-01 11:52:32
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2018-02-01 11:52:34
Document TitleUsers Manual
Document CreatorAdobe InDesign CC 13.0 (Macintosh)

CB200-M
User Guide
2
TABLE OF CONTENTS
RF Safety & FCC............................................................................................................................... 4
Safety & Information........................................................................................................................5
Electromagnetic Interference Compliance.......................................................................................6
Computer Software Copyrights........................................................................................................7
Documentation Copyrights...............................................................................................................8
Battery Installation............................................................................................................................9
Controls Interface ............................................................................................................................10
LCD Display...................................................................................................................................... 11
LCD Wakeup.....................................................................................................................................12
Scrolling Menu................................................................................................................................. 13
MURS Channel Selection.................................................................................................................14
Code Selection................................................................................................................................. 15
Message Recording..........................................................................................................................16
Message Playback............................................................................................................................17
Volume Adjusting............................................................................................................................. 18
LCD Contrast.....................................................................................................................................19
TABLE OF CONTENTS
Software Version..............................................................................................................................20
Call Cycles.........................................................................................................................................21
Cycle Delay........................................................................................................................................22
Inverted Codes..................................................................................................................................23
RF Busy Delay....................................................................................................................................24
Mounting the Device........................................................................................................................25
Frequency Tables - MURS................................................................................................................ 26
CTCSS Code Tables...........................................................................................................................27 - 29
Notes.................................................................................................................................................30 - 31
4
RF SAFETY & FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. Howev­er, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Observe a minimum safe distance of 20 cm from the device to the operator.
FCC License is not required. This device operates on frequencies authorized for use in the Multi-Use
Radio Service (MURS). MURS frequencies are available for unlicensed business or personal use.
Federal Communications Commision
445 12th Street, SW
Washington, DC 20554
1-888-225-5322 (1-888-CALL FCC) Voice: toll free 1-888-835-5322 (1-888-TELL FCC) TTY: toll free
SAFETY & INFORMATION
The CB200-M requires care in mounting and servicing. Observing the following precautions will
ensure the proper function and safety of the unit.
CAUTION!
• Do not screw through the device to mount to a surface.
• Keep the Callbox away from water, high moisture, and high temperatures.
• This equipment contains potentially hazardous voltages.
• Do not attempt to disassemble the unit.
• E xcept for the batteries, this unit contains absolutely no user serviceable components and all
service should be completed only by qualified service personnel.
• Do not dispose of batteries in fire. The batteries may explode.
• Do not open or mutilate the batteries, they contain dangerous electrolytes.
• Operating this unit in any capacity other than its intended purpose may result in system failure
and possible injury and voids any and all warranty.
6
EMI COMPATIBILITY
ELECTROMAGNETIC INTERFERENCE (EMI) COMPLIANCE
NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if
inadequately shielded, designed, or otherwise configured for electromagnetic compatibility.
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation of the device.
(3) Changes or modifications made to this device, not expressly approved by Motorola, could void
the authority of the user to operate this equipment.
COMPUTER SOFTWARE COPYRIGHTS
The Motorola Solutions products described in this manual may include copyrighted Motorola
Solutions computer programs stored in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola Solutions certain exclusive rights
for copyrighted computer programs including, but not limited to, the exclusive right to copy
or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted
Motorola computer programs contained in the Motorola Solutions products described in
this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in
any manner without the express written permission of Motorola Solutions. Furthermore,
the purchase of Motorola Solutions products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the copyrights, patents or patent
applications of Motorola Solutions, except for the normal nonexclusive license to use that
arises by operation of law in the sale of a product.
8
DOCUMENTATION COPYRIGHTS
No duplication or distribution of this document or any portion thereof shall take place without
the express written permission of Motorola Solutions. No part of this manual may be reproduced,
distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose
without the express written permission of Motorola Solutions.
DISCLAIMER
The information in this document is carefully examined, and is believed to be entirely reliable.
However, no responsibility is assumed for inaccuracies. Furthermore, Motorola Solutions reserves
the right to make changes to any products herein to improve readability, function, or design.
Motorola Solutions does not assume any liability arising out of the applications or use of any
product or circuit described herein; nor does it cover any license under its patent rights, nor the
rights of others.
INSTALLING THE BATTERIES
BATTERY
HOLDER
The CB200-M uses six (6) AA batteries.
1. Remove the battery holder from
cardboard packaging.
COPPER
CONTACT
2. Orient the battery holder with the four
copper contacts pointed
towards you.
3. Insert the batteries following battery
sled sticker.
BATTERY
HOLDER
BATTERY HOLDER
4. Insert battery holder into
COVER
bottom of device with the four contacts
first.
5. Replace the battery holder cover.
10
CONTROL INTERFACE
Available Controls and Components
1. Menu Button
2. Enter Button
3. Esc Button
4. Display
5. Microphone
6. Wake Up Button
7. Call Button
LCD DISPLAY
Initial Power-Up
Once the batteries are installed in
the unit, the Call Button blinks and
LCD display shows
Interface ENA.
If the USB Serial Interface is not
to be used, press the ESC button
to exit this mode. The default
status screen will be shown on the
display. If nothing is pressed, the
unit will enter sleep mode after 60
seconds and the screen will clear.
Status Screen
The Status Screen toggles the
current Frequency and CTCSS
setting continuously.
11
CB200-M
Insert Battery
INTERFACE ENA
-ESC to EXIT-
Press Esc
Freq No: 6
MHZ:154.5700
CTCSS CODE: 1
67.0 HZ ANA
Channel Spacing
12.5 KHZ
12
LCD WAKEUP
The screen is in a blank “sleep” state during most operation, even when the system is operating.
This is a feature to increase battery life and prevent tampering.
To enter the Menu options, press the Wakeup button on the unit. The large round button blinks to
indicate it is awake.
The display remains disabled until any LCD menu control button is pressed. The LCD menu control
buttons are Up or Down as shown in the following.
SCROLLING MENU
You can setup preferred features on CB200-M by scrolling through the menu options. Press the
Menu Buttons to scroll through menus.
Menu options are presented in the order below, and the list repeats continuously.
MURS
Set MURS Channel Number
Set Radio Code
Message Record
Message Playback
Volume Adjust
LCD Contrast
Software Version
Call Cycles
Cycle Delay
Inverted Codes
RF Busy Delay
13
14
MURS CHANNEL SELECTION
Set MURS Channel Number
When the unit is awake and displaying the Status Screen, press the
UP or Down Menu buttons until “MURS Chan No?” appears.
MURS Chan No?
Press Enter
Old:6 154.5700
New:6 154.5700
Press Up or Down to
select new channel
Old:6 154.5700
New:2 154.6000
Press Enter to select new
channel
Old:6 154.5700
**Chan Updated
Press Enter to select new
channel
The CB200-M is now programmed with the new channel selected.
RADIO CODE SELECTION
15
Set Squelch Code Frequency
When the unit is awake and displaying the Status Screen, press the
UP or Down Menu buttons until “Radio Code?” appears.
Press Enter
Old:12 100.0 Hz
New:12 100.0 Hz
Press Up or Down to
select new squelch code
Channel No 1-7?
Ch:1 154.5700
Press Up or Down to
select new channel
Old:12 100.0 Hz
New:13 103.5 Hz
Press Enter to select
new squelch code
Channel No 1-7?
Ch:3 151.8200
Press Enter to select
new channel
Old:12 100.Hz
**Code Updated
Press Enter to select
new squelch code
Radio Code?
The CB200-M is now programmed with the new CTCSS squelch code.
16
MESSAGE RECORDING
Press Up or Down button until “Msg Record?” appears.
Msg Record?
Press Enter
Select Message?
Aux Message
Press Up or Down to find
message to record.
Select Message?
Local Message
Press Enter to select message to record.
Hold ENTER Btn
To Record Msg
Hold Enter button to record
a new message.
The new message automatically playback to verify it was recorded correctly. Message cannot be
longer than 10 seconds.
MESSAGE PLAYBACK
Press Up or Down button until “Msg Playback?” appears.
Msg Playback?
Press Enter
Select Message?
Local Message
Press Up or Down to find
message to playback.
Select Message?
Radio Message
Press Enter to select
message to playback.
-Playback ActRadio Message
Select new message to
playback or press Esc to exit.
17
18
VOLUME ADJUSTMENT
Press Up or Down button until “Volume Adjust?” appears.
Volume Adjust?
Press Enter
Speaker Volume?
Press Up or Down to select which volume
to adjust, then press Enter.
-Speaker VolVol(1-63): 45
Press Up or Down until desired volume
selection is shown. The volume settings
take place immediately. Press Esc to exit.
LCD CONTRAST
Press Up or Down button until “LCD Contrast?” appears.
LCD Contrast?
-LCD Contrast(0-15): 0
Press Enter
Press Up or Down until desired contrast
selection is shown. The contrast settings
take place immediately. Press Esc to exit.
If the need arises to adjust the LCD contrast, check the batteries first. The batteries may be too
weak to operate the unit correctly.
19
20
SOFTWARE VERSION
You may be asked by a field support or technical support personnel to determine the CB200-M
device’s software version.
Press Up or Down button until “Software Ver?” appears.
Press Enter
The software version is shown
CALL CYCLES
Call Cycles refers to the repeating radio broadcasts that will occur when the call button is active.
Press Up or Down button until “Call Cycles?” appears.
Call Cycles?
Press Enter
Old: 2 cycles
New: 2 cycles
Press Up or Down to increase or decrease
the Call Cycle selection. The range is 1-30
cycles. Press Enter to select the new Call
Cycle.
21
CYCLE DELAY
22
Call Delay refers to the delay (in seconds) between repeating radio broadcasts that occur when
the call button (or aux button) is active.
Press Up or Down button until “Cycle Delay?” appears.
Cycle Delay?
Old: 45 sec
New: 45 sec
Press Enter
Press Up or Down to increase or decrease
the Cycle Delay selection. The range is
10-180 seconds. Press Enter to select the
new Call Cycle.
INVERTED CODES
When selecting digital CTCSS (squelch) codes, some receiving units may require inverted Octal
numeric codes. Typically, receivers use the non-inverted codes. CB200-M is set to non-inverted by
default.
Note: This feature only applicable for CB200-M
Press Up or Down button until “Inverted Codes?” appears.
Press Enter
Press Up or Down to select between
NORMAL and INVERTED. Press Enter
to select the new setting.
WARNING: If the incorrect digital code is selected, the radio broadcast will not open the squelch
of the receiving unit.
23
24
RF BUSY DELAY
RF Busy Delay defines the amount of time after the CB200-M recognizes an open channel before it
makes it’s radio transmission. This is helpful if you would like to set a longer time between button
press and radio message or to prevent transmitting while conversations are ongoing in some
environments.
Press Up or Down button until “RF Busy Delay?” appears.
Press Enter
Use the Up or Down to cycle through the
RF Busy Delay selections (3-15 seconds).
Press Enter to select the new value, or
Esc to exit without any changes. Default
setting is 3-seconds.
MOUNTING THE DEVICE
The CB200-M can be mouted to the wall using the included 3M DualLock strips or by using the
optional wall mounting bracket.
Using 3M DualLock
Ensure both the back of the callbox and the area of the surface that is being attached to is clean,
flat, and dry.
1. Peel off one side of the DualLock’s release backing and firmly adhere to the left side of the unit.
Repeat this with the other DualLock to the right side of the callbox.
2. Once both strips of DualLock are attached to the callbox, peel off the white release backing and
carefully align the unit to be level on the surface you intend to place it.
3. Once the callbox appears aligned, firmly press it to the wall in one motion.
Note: The callbox can be removed by applying firm pressure around the exterior edge of the unit.
For optional mounting accessories, please use the mounting bracket available from your Motorola
CB200-M distributor.
25
26
FREQUENCY SELECTION TABLE - MURS
Freq.
No.
Freq. Value
CTCSS
Code
Bandwidth
(KHz)
Description
154.5700
20 KHz
Default Freq / Code
154.6000
20 KHz
Default Freq / Code
151.8200
57 (131)
11.25 KHz
Default Freq / Code
151.8800
57 (131)
11.25 KHz
Default Freq / Code
151.9400
57 (131)
11.25 KHz
Default Freq / Code
154.5700
57 (131)
20 KHz
Default Freq / Code
154.6000
57 (131)
20 KHz
Default Freq / Code
Note: the CTCSS Code shown is the default setting. The CTCSS squelch code can be changed by
the user. (Refer to the Radio Code Selection section on page 15.)
CTCSS CHART (ANALOG)
27
No.
Code Hz
No.
Code Hz
No.
Code Hz
No.
Code Hz
67.0
13
103.5
25
156.7
37
241.8
71.9
14
107.2
26
162.2
38
250.3
74.4
15
110.9
27
167.9
77.0
16
114.8
28
173.8
79.7
17
118.8
29
179.9
82.5
18
123.0
30
186.2
85.4
19
127.3
31
192.8
88.5
20
131.8
32
203.5
91.5
21
136.5
33
210.7
10
94.8
22
141.3
34
218.1
11
97.4
23
146.2
35
225.7
12
100.0
24
151.4
36
233.6
CTCSS CHART (DIGITAL)
28
No.
Code
No.
Code
No.
Code
No.
Code
39
023
51
073
63
156
75
261
40
025
52
074
64
162
76
263
41
026
53
117
65
165
77
265
42
031
54
115
66
172
78
271
43
032
55
116
67
174
79
306
44
043
56
125
68
205
80
311
45
047
57
131
69
223
81
315
46
051
58
132
70
226
82
331
47
054
59
134
71
243
83
343
48
065
60
143
72
244
84
346
49
071
61
152
73
245
85
351
50
072
62
155
74
251
86
364
CTCSS CHART (DIGITAL)
No.
Code
No.
Code
No.
Code
87
365
99
503
111
654
88
371
100
506
112
662
89
411
101
516
113
664
90
412
102
532
114
703
91
413
103
546
115
712
92
423
104
565
116
723
93
431
105
606
117
731
94
432
106
612
118
732
95
445
107
624
119
734
96
464
108
627
120
743
97
465
109
631
121
754
98
466
110
632
29
30
NOTES
NOTES
31
Printed in USA
02012018M

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36
Create Date                     : 2018:02:01 11:52:32-06:00
Metadata Date                   : 2018:02:01 11:52:34-06:00
Modify Date                     : 2018:02:01 11:52:34-06:00
Creator Tool                    : Adobe InDesign CC 13.0 (Macintosh)
Instance ID                     : uuid:ba531fb9-faeb-0143-a96a-bbcb976273f7
Original Document ID            : xmp.did:D5D306E7B46CE7118775A0B2611E3B88
Document ID                     : xmp.id:39465359-795c-4b1c-9687-50d071a5bb51
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4f5e08eb-595d-4fe3-a66e-8caec1a989eb
Derived From Document ID        : xmp.did:17D1F9FB61CEE711B614DB01F3F9CCC7
Derived From Original Document ID: xmp.did:D5D306E7B46CE7118775A0B2611E3B88
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.0 (Macintosh)
History Changed                 : /
History When                    : 2018:02:01 11:52:32-06:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 32
Creator                         : Adobe InDesign CC 13.0 (Macintosh)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ489FT3844

Navigation menu