Motorola Solutions 89FT4860 CLS Series Two-Way Radios User Manual 6864110w15o

Download:
Mirror Download [FCC.gov]
Document ID	311925
Application ID	WRVSOA/hql/Ykbg2eZQtOg==
Document Description	Exhibit D Users Manual per 2 1033 c3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	260.98kB (3262189 bits)
Date Submitted	2003-03-20 00:00:00
Date Available	2003-03-20 00:00:00
Creation Date	2003-02-14 03:45:24
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2003-03-13 13:55:00
Document Title	6864110w15o.book
Document Creator	PScript5.dll Version 5.2
Document Author:	fdr049

6864110w15o.book Page 1 Thursday, February 13, 2003 9:46 PM
User's Guide
SERIES TWO-WAY RADIO
DRAFT
@6864110W15@
6864110W15-O
Models CLS1110 and CLS1410
031092o
6864110w15o.book Page 2 Thursday, February 13, 2003 9:46 PM
DRAFT
6864110w15o.book Page 1 Thursday, February 13, 2003 9:46 PM
Contents
Introduction ................................ 2
FCC Licensing Information ...... 4
Safety and General Information 6
Radio Controls ......................... 13
Getting Started ......................... 14
Installing the Swivel Belt
Holster ................................. 14
Installing the Batteries ............ 15
Charging the Battery............... 16
Turning Your Radio On and
Off........................................ 19
Adjusting the Volume.............. 20
Reading the Display ............... 20
Talking and Receiving ............. 21
Basic Radio Operation............ 21
Signal Strength and Channel Busy
Indicators............................. 21
Talk Range ............................. 22
Handsfree Use
(CLS1410 only) ................... 22
Locking the Keypad ................ 24
Monitoring a Channel ............. 24
Scanning (CLS1410 Only)...... 24
Programming Features ............ 26
Factory Default Settings.......... 27
Entering Programming Mode .. 28
Cloning Radio Settings ............ 32
Advanced Features .................. 33
Troubleshooting ...................... 35
Use and Care............................. 38
Frequencies and Bandwidths.. 39
Spirit GT Series Programming 45
Warranty .................................... 46
6864110w15o.book Page 2 Thursday, February 13, 2003 9:46 PM
Introduction
Introduction
Thank you for purchasing a Motorola _Series Radio. Your radio is a product of
Motorola’s 70 plus years of experience as a world leader in designing and
manufacturing communications equipment. The _Series radios provide costeffective communications for businesses such as retail stores, restaurants, hotels,
and schools. Motorola professional two-way radios are the perfect communications
solution for all of today’s fast-paced industries.
Please read this guide carefully so you know how to properly operate the radio
before use.
Package Contents
• _Series Radio
• Swivel Belt Holster
• Lithium Ion Battery
• Drop-In Charger with Transformer
• User's Guide
• Accessory Brochure
• Warranty Card
6864110w15o.book Page 3 Thursday, February 13, 2003 9:46 PM
ATTENTION
Before using this product, read the RF energy awareness information and operating
instructions in the Safety and General Information section of this guide to ensure
compliance with RF energy exposure limits.
Introduction
For product-related questions, please call:
1-800-448-6686 in the USA
1-888-390-6456 TTY (Text Telephone)
On the Web:
www.motorola.com/radios/professional
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or
service names are the property of their respective owners.
© Motorola, Inc. 2003.
6864110w15o.book Page 4 Thursday, February 13, 2003 9:46 PM
FCC Licensing Information
FCC Licensing Information
_Series professional two-way radios operate on radio frequencies that are regulated by the Federal
Communications Commission (FCC). In order to transmit on these frequencies, you are required to have a
license issued by the FCC.
Application is made available on FCC Forms 601, schedules D and H, and remittance form 159. If ordering the
forms by mail, phone, or from the FCC website, please request document number 000601, which includes all
forms and instructions. If using the FCC Fax-on-Demand system, use the 7-digit order numbers listed below.
To obtain the required forms, please use the following contact information:
By Phone or Web
Faxed
Mailed
or for questions
contact the Fax-On-Demand call the FCC forms hotline
regarding FCC license
system at:
at:
contact the FCC at:
1-888-CALL-FCC
1-800-418-FORM
1-202-418-0177
1-888-225-5322
1-800-418-3676
or: http://www.fcc.gov
Request forms 3060001,
Request document 000601
Request document 000601
3060003, and 3060006
Before filling out your application, you must decide which frequency(ies) you can operate on. See Frequencies
and Bandwidths on page 39. For questions on determining your radio frequency, please call Motorola Product
Services at 1-800-448-6686.
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC
to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should
be made only by or under the supervision of a person certified as technically qualified to perform transmitter
maintenance and repairs in the private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor,
etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed is subject to government
regulations and may be prohibited.
FCC Licensing Information
6864110w15o.book Page 5 Thursday, February 13, 2003 9:46 PM
6864110w15o.book Page 6 Thursday, February 13, 2003 9:46 PM
Safety and General Information
Safety and General Information
Important Information on Safe and Efficient Operation.
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information contained in user guides
published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with
the occupational/controlled environment RF exposure limits, always adhere to the following procedure:
• Transmit no more than 50% of the time.
• To transmit (talk), press the Push to Talk (PTT) button.
• To receive calls, release the PTT button.
Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure
only when transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola radio is designed to comply with the following national and international standards and guidelines
regarding exposure of human beings to radio frequency electromagnetic energy:
• United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 subpart J
• American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 11992
6864110w15o.book Page 7 Thursday, February 13, 2003 9:46 PM
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio Frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
• Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human
Exposure) Standard 2001 (applicable to wireless phones only)
• ANATEL, Brazil Regulatory Authority, Resolution 256 (April 11, 2002) “additional requirements for SMR,
cellular, and PCS product certification.”
To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy
is within the guidelines set forth in the above standards, always adhere to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could damage the radio and may violate FCC regulations.
DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects the effective range.
Two-Way Radio Operation
When using your radio as a traditional two-way radio, hold the radio in a vertical position
with the microphone 1 to 2 inches (2.5 to 5 cm) away from the lips.
Safety and General Information
•
•
•
Safety and General Information
6864110w15o.book Page 8 Thursday, February 13, 2003 9:46 PM
Body-Worn Operation
To maintain compliance with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body
when transmitting, always place the radio in a Motorola-supplied or approved clip, holder, holster, case, or body
harness for this product. Use of non-Motorola-approved accessories may exceed FCC/Health Canada RF
exposure guidelines. If you do not use one of the Motorola-supplied or approved body-worn accessories, and
are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch
(2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an accessory cable, position the radio
and its antenna at least 1 inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories visit our website at www.motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately
shielded, designed, or otherwise configured for electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where
posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive
to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in
accordance with applicable regulations per airline crew instructions.
Medical Devices - Pacemakers
The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be
maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with
the independent research by, and recommendations of the U.S. Food and Drug Administration.
Persons with pacemakers should:
• ALWAYS keep the radio more than six inches (15 cm) from their pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential for interference.
• Turn the radio OFF immediately if you have any reason to suspect that interference is taking place.
Medical Devices - Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may
want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device to determine if it is
adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.
Safety and General Information
6864110w15o.book Page 9 Thursday, February 13, 2003 9:46 PM
6864110w15o.book Page 10 Thursday, February 13, 2003 9:46 PM
Safety and General Information
Safety and General Use While Driving
10
Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using
your radio while driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving conditions so require.
Operational Warnings
For Vehicles with an Air Bag
Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with
great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be
propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type
especially qualified for use in such areas as “Intrinsically Safe.” Do not remove, install, or charge batteries in
such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury
or even death.
Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below
decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles,
such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are often but not always posted.
6864110w15o.book Page 11 Thursday, February 13, 2003 9:46 PM
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with
your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as
jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical
circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse, or other container with metal objects.
Battery Charger Safety Instructions
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged
in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet
installed by a qualified electrician. An improper condition can result in a risk of electric shock.
Safety and General Information
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting
caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.
11
Safety and General Information
6864110w15o.book Page 12 Thursday, February 13, 2003 9:46 PM
12
4. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the
charger from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance
or cleaning.
6. Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock, or
personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord
could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that:
• The pins on the plug of the extension cord are the same number, size, and shape as those on the plug of
the charger.
• The extension cord is properly wired and in good electrical condition.
• The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.
• The supply cord of this charger cannot be replaced. If the cord is damaged, call Motorola Product Services
at 1-800-448-6686 in the USA or 1-888-390-6456 TTY (Text Telephone).
6864110w15o.book Page 13 Thursday, February 13, 2003 9:46 PM
Radio Controls
Microphone
Use B to:
Transmit call tone
Accessory Jack
Use Push to Talk to:
Talk
Exit a menu
Use [ and ] to:
Change channels
Use T to:
Monitor the frequency
Scan channels (CLS1410 only)
(CLS1410 only)
Radio Controls
Use P to:
Turn radio on/off
Adjust radio volume
Change menu settings
Speaker
Use S to:
Lock the keypad
Scroll through menus
020976o
13
6864110w15o.book Page 14 Thursday, February 13, 2003 9:46 PM
Getting Started
Getting Started
14
Installing the Swivel Belt Holster
1. Slide the bottom of radio into the holster until it snaps
into place.
2. To remove, push the tab on the holster and pull the radio
away from the holster.
Note: In case of loss, please contact your point-of-sale or
call 1-800-448-6686 to request replacement part
number HCLN4013.
Installing the Batteries
Your radio uses a rechargeable Lithium Ion (Li Ion) battery or 3 AAA Alkaline
batteries with the 1564200W18 Alkaline Battery Tray (not included with all models).
Li Ion Battery
1. If the battery door is already in place on the radio, push
down on the recess on the door and slide it off the radio.
2. Insert the battery, printed arrows first, into the battery
compartment and press down to secure firmly in place.
3. Slide and snap the battery door into place.
AAA Alkaline Batteries
1. If the battery door is already in place on the radio, push
down on the recess on the door and slide it off the radio.
2. Insert 3 AAA batteries into the battery tray as shown by
the markings inside the tray.
3. Insert the battery tray into the battery compartment and press down to secure
firmly in place.
4. Slide and snap the battery door into place.
5. Press S until A or n flashes (this menu does not appear if using a Motorola
Li Ion battery).
6. Press [ or ] to select A for Alkaline batteries, or n for rechargeable AAA cells.
Getting Started
6864110w15o.book Page 15 Thursday, February 13, 2003 9:46 PM
15
Getting Started
6864110w15o.book Page 16 Thursday, February 13, 2003 9:46 PM
Charging the Battery
Use only the charger supplied with the radio, or other _ Series power
accessories. For optimum battery life, do not charge the battery for prolonged
periods after it is fully charged. Charging the battery over the weekend is acceptable.
Using the Drop-in Charger
1. Place the charger on a flat surface.
2. Insert the plug of the power cord into the
jack on the charger.
3. Plug the cord into an AC outlet.
4. Turn the radio off. If the radio is on while
charging, it will take longer to fully charge.
5. Insert the radio (with battery installed) into
the front charging pocket.
Note: The radio will fit in the charger with
the holster on.
The drop-in charger will also sequentially
charge a spare 56557 Li Ion battery. The spare battery will not begin to charge until
the radio battery is fully charged. Both batteries will charge in approximately 2–6
hours.
16
Using the 56531 Multi-Unit Charger
The Multi-Unit Charger (MUC) allows drop-in charging of 6 radios or batteries
(56556 Li Ion rechargeable battery, SNN5571 only). Batteries can be charged
inside the radios or removed and placed in the MUC separately. Each of the
6 charging pockets can hold a radio or battery, but not both.
1. Place the charger on a flat surface.
2. Insert the power cord plug into the jack on the MUC.
3. Plug the cord into an AC outlet.
4. Turn the radio off.
5. Insert the radio or battery into the charging pocket.
Battery charging pocket
Radio charging pocket
Getting Started
6864110w15o.book Page 17 Thursday, February 13, 2003 9:46 PM
17
Getting Started
6864110w15o.book Page 18 Thursday, February 13, 2003 9:46 PM
Charging Status LEDs
On the drop-in (single radio) charger, the radio and battery charging pockets have
their own LEDs.
On the MUC, each of the 6 charging pockets has an LED. The LEDs are grouped
into pairs to show which charging pockets are paired (for cloning, see page 32).
The LED is solid red when the battery is charging, and solid green when charging is
complete.
Battery Meter
The battery meter in the upper left corner of the display (see page 20) shows how
much battery power is remaining.
Battery Type
3 Bars
2 Bars
1 Bar
Flashing
100%–85%
85%–25%
25%–10%
Final 10%
AAA Alkaline 100%–75%
75%–40%
40%–10%
Final 10%
Li Ion
Battery Life
Based on 5% transmit, 5% receive, 90% standby (standard duty cycle):
Li Ion – 12 Hours
18
AAA Alkaline – 10 Hours
6864110w15o.book Page 19 Thursday, February 13, 2003 9:46 PM
When you turn the radio on, the radio chirps and the display briefly
shows all features and display segments.
The radio then displays the current channel (larger number in the
center) and the frequency assigned to that channel (on the right
indicated by l).
Getting Started
Turning Your Radio On and Off
See page 13 for a basic radio diagram.
Turn P clockwise to turn the radio on, and counterclockwise to turn the radio off.
When the radio is on, the transmit light on the top of the radio flashes every
3 seconds.
The Interference Eliminator Code displays briefly (indicated by
y), then the current channel remains displayed.
19
6864110w15o.book Page 20 Thursday, February 13, 2003 9:46 PM
Getting Started
Adjusting the Volume
Turn P clockwise to increase the volume, and counterclockwise to decrease the
volume.
Note: Do not hold the radio too close to your ear when adjusting the volume.
Reading the Display
Battery Meter
Channel
nterference Eliminator
Code Indicator
Programming Mode
Scan (CLS1410 Only)
20
Signal Strength and Channel Busy Indicator
VibraCall® Alert Indicator
Frequency and
Interference Eliminator
Code
Keypad Lock
Frequency Indicator
Microphone Gain and
VOX (CLS1410 only)
6864110w15o.book Page 21 Thursday, February 13, 2003 9:46 PM
Talking and Receiving
1. Press and hold T to check for channel activity. If you hear static, the channel is
clear to use. Do not transmit if someone is speaking on the channel. Press T
again to stop monitoring.
2. To talk, press and hold Push to Talk and speak into the microphone. Hold the
radio 2 to 3 inches away from your mouth.
3. To listen, release Push to Talk.
The transmit light on the top of the radio is red when transmitting.
Signal Strength and Channel Busy Indicators
When there is activity on a frequency, the radio displays w and the
transmit light flashes at a faster rate of once per second.
When there is activity on the same frequency and code as your radio
(your radio is receiving), the radio displays w and a signal strength
from 1 (weakest) to 6 (strongest). This can help determine when a
radio is moving out of range.
Talking and Receiving
Basic Radio Operation
Note: Obstacles that block the signal path may affect the strength of the incoming
signal.
21
6864110w15o.book Page 22 Thursday, February 13, 2003 9:46 PM
Talking and Receiving
Talk Range
22
Industrial
Multi-Level
Outdoor
Inside steel/concrete
industrial buildings
Inside multi-level
buildings
Flat ground with no
obstructions
Up to 200,000 sq. ft.
Up to 15 floors
Up to 5 miles
Handsfree Use (CLS1410 only)
The CLS1410 model radio can operate handsfree when used with or without
compatible voice activation (VOX) accessories. A short delay occurs between the
time when you start talking and when the radio transmits.
With Compatible VOX Accessories
1. Turn the radio off.
2. Open the accessory cover.
3. Plug the audio accessory firmly into the accessory jack.
4. Turn the radio on. The radio displays g. If g is flashing
and you are setting up the VOX accessory for the
first time, set the VOX sensitivity level (see page 23).
5. Lower the radio volume BEFORE placing the accessory
in or near your ear.
6864110w15o.book Page 23 Thursday, February 13, 2003 9:46 PM
Setting the VOX Sensitivity
You can adjust the sensitivity of your radio’s accessory or microphone during VOX
operation to suit different operating environments. These menus appear only if the
VOX feature is in use, which is indicated by g.
1. Press S until g displays. The radio displays H if you are
setting the external VOX (with audio accessory) or I if you are
setting the internal VOX (without accessory).
2. Press [ or ] to select the sensitivity level:
0 = Off
1 = Low
2 = Medium
3 = High
External VOX
020995o
Talking and Receiving
6. To transmit, speak into accessory microphone. To receive, stop talking.
To disable VOX operation, press Push to Talk or remove the audio accessory.
Note: To order accessories, visit www.motorola.com/radios/professional,
call 1-800-448-6686, or contact your point of purchase.
23
6864110w15o.book Page 24 Thursday, February 13, 2003 9:46 PM
Talking and Receiving
Locking the Keypad
You can lock the keypad to avoid accidentally changing your radio settings.
1. Press and hold S for 3 seconds.
2. To unlock, press and hold S for 3 seconds.
24
Monitoring a Channel
Monitoring allows you to check for activity on a channel.
1. Press and hold T. If the channel is clear to use, you will hear
static and w and 0 will display.
2. Press T again to stop monitoring.
Scanning (CLS1410 Only)
You can scan up to 4 channels and frequencies. When the radio
detects activity, it stops scanning and locks in on the active channel. This allows you
to talk and listen to the person transmitting without changing channels.
To scan channels regardless of the code in use on the channels, change the code
for your channel to 0 before you start to scan.
To start scanning, briefly press T.
The scan icon h displays and the radio begins to scan through the channels. When
the radio detects activity, it stops on that channel and displays w and the channel
number.
To talk to the person transmitting without switching channels, press Push to Talk
within 5 seconds. If no transmission occurs within 5 seconds, scanning resumes.
If you press Push to Talk while the radio is scanning, the radio transmits on the
channel you were on before you started scanning.
To stop scanning, briefly press T.
Skipping and Removing Channels While Scanning
Scan has several temporary features to make it easier to use.
• Scan advance
If the radio stops scanning on a channel you do not want to listen to, press ] to
resume scanning for the next active channel.
• Nuisance delete
Press and hold [to temporarily remove a channel from the scan list. The
channel return the next time you use the scan feature.
Talking and Receiving
6864110w15o.book Page 25 Thursday, February 13, 2003 9:46 PM
25
6864110w15o.book Page 26 Thursday, February 13, 2003 9:46 PM
Programming Features
Programming Features
26
Programming mode allows you to change the following settings on your radio:
• Channel
• Frequency
• Interference eliminator code
• Call tones
• Microphone gain
• Scan list (CLS1410 only)
• Available channels (CLS1410 only)
Notes:
• To talk with someone on your two-way radio, the channel, frequency, and
interference eliminator code must be the same on both radios.
• You cannot enter programming mode while a VOX accessory is plugged into the
radio.
6864110w15o.book Page 27 Thursday, February 13, 2003 9:46 PM
Factory Default Settings
Your radio is programmed at the factory to the following settings:
Channel
CLS1110
CLS1410
Code
Call Tone/
VibraCall®
VOX
Microphone
Gain
Not available
Off (0)
Not available
Off (0)
Programming Features
Frequency
2 (medium sensitivity)
To restore the factory settings, turn the radio on while holding Push to Talk and S
for 3 seconds.
27
Programming Features
6864110w15o.book Page 28 Thursday, February 13, 2003 9:46 PM
28
Entering Programming Mode
Press and hold Push to Talk and T for 3 seconds while turning the radio on. The
radio beeps and displays k, the channel number flashes, and the frequency
(indicated by l) and code (indicated by y) display alternately.
Selecting a Channel (CLS1410 Only)
1. In programming mode, press S until the channel number
flashes and the frequency and code display alternately (this is
the first setting after you enter programming mode).
2. Press [ or ] to select the channel.
3. Press and hold Push to Talk to exit programming mode, or
press S to continue programming.
Programming the Frequency
1. In programming mode, press S until l displays and the
frequency number flashes.
2. Press [ or ] to select the frequency.
3. Press and hold Push to Talk to exit programming mode, or
press S to continue programming.
Note: See page 39 for information on frequencies for communicating with other
business radios. If you are matching your _ Series radio to an existing
Spirit GT radio, see page 45.
Programming the Interference Eliminator Code
The interference eliminator code helps minimize interference by providing you with
code combinations that filter out static, noise, and unwanted messages.
1. In programming mode, press S until y displays and the
code number flashes.
2. Press [ or ] to select the code (see page 42).
3. Press and hold Push to Talk to exit programming mode, or
press S to continue programming.
Programming the Available Channels (CLS1410 only)
For applications requiring fewer channels, you can reduce the number of available
channels.
1. In programming mode, press S until = displays and the
channel number flashes.
2. Press [ or ] to select the number of channels you want
available.
3. Press and hold Push to Talk to exit programming mode, or
press S to continue programming.
Note: Settings for channels made unavailable are retained by the radio.
Programming Features
6864110w15o.book Page 29 Thursday, February 13, 2003 9:46 PM
29
Programming Features
6864110w15o.book Page 30 Thursday, February 13, 2003 9:46 PM
30
Programming Call Tones and VibraCall® (CLS1410 only)
Your radio can transmit call tones to other radios in your group so you can alert them
that you are about to talk. Your radio comes with call tones turned off (set to 0), but
you can change this setting to choose a distinctive call tone.
The VibraCall® feature is an additional call tone option that makes the CLS1410
radio vibrate briefly when it receives and when you have not transmitted or received
in the last 30 seconds. Select call tone 4 to turn VibraCall® on. i displays on the
radio when VibraCall® is on.
1. In programming mode, press S until E displays.
2. Press [ or ] to hear and select the call tone. Select call
tone 4 for VibraCall® (CLS1410 only).
3. Press and hold Push to Talk to exit programming mode, or
press S to continue programming.
To transmit your call tone before transmitting, press B on the side of the radio.
Programming Microphone Gain
You can adjust the microphone sensitivity to suit different users or operating
environments.
1. In programming mode, press S until g and ? display.
2. Press [ or ] to select the sensitivity level:
3 = High sensitivity, for quiet environments
2 = Medium sensitivity (default)
1 = Low sensitivity, for loud environments
3. Press and hold Push to Talk to exit programming mode, or press S to continue
programming.
Editing the Scan List (CLS1410 Only)
For faster scanning and to avoid hearing unwanted transmissions, you can edit the
scan list to skip channels.
1. In programming mode, press S until h displays and the
channel number and Y or n flash.
2. Press [ or ] to select the channel you want to remove from
the scan list.
3. Press T to display either Y to include the channel or n to
exclude the channel.
4. Press and hold Push to Talk to exit programming mode, or press S to continue
programming.
Programming Features
6864110w15o.book Page 31 Thursday, February 13, 2003 9:46 PM
31
6864110w15o.book Page 32 Thursday, February 13, 2003 9:46 PM
Cloning Radio Settings
Cloning Radio Settings
32
You can duplicate _ Series radio settings from one radio (the source) to a
second radio using the 5653 Multi-Unit Charger (MUC) optional accessory. See the
MUC User's Guide for more information.
You can clone only one radio at a time. A multi-channel radio can clone to a singlechannel radio, but only the first channel is cloned. The MUC does not need to be
plugged in for cloning.
1. On the source radio, press and hold Push to Talk and T for 3 seconds while
turning the radio on. The radio beeps and displays k.
2. Place the source radio in one of the charging pockets.
Paired
3. Turn the target radio on and place it in the charging pocket
pockets
that is paired with the pocket containing the source radio.
There are 3 paired charging pockets as indicated by the
3 pairs of charging status LEDs.
4. Press and hold T on the source radio. The source radio
tranmits its settings to the target radio. If cloing was
successful, P or Pass displays on the source radio and the
LEDs
target radio displays all feature icons. If cloning was not
successful, F or Fail displays on the source radio.
5. Turn the target radio off and back on again to use.
6. To clone additional radios, repeat steps 3 - 4.
7. To exit programming mode on the source radio, press and hold Push to Talk
until k no longer appears.
6864110w15o.book Page 33 Thursday, February 13, 2003 9:46 PM
Advanced Features
Press This Button
While Turning
the Radio On
Default
Setting
Turn Keypad Tones On/Off
Turns keypad beeps off for silent menu operation.
On
Turn End-of-Transmission Tone On/Off
If enabled, your two-way radio transmits a tone
when you finish transmitting (like saying Roger or
Over).
If keypad tones are off and end-of-transmission tone
is on, you will not hear the end-of-transmission tone,
but it is transmitted.
Off
To Do This
Advanced Features
You can set the following features by pressing and holding additional buttons while
you turn the radio on.
33
6864110w15o.book Page 34 Thursday, February 13, 2003 9:46 PM
Advanced Features
To Do This
34
Press This Button
While Turning
the Radio On
Default
Setting
Turn Battery Save Mode On/Off
Decreases attack time, which is the brief period of
time between when the radio receives a
Push to Talk T [
transmission on its frequency and broadcasts audio.
Turning battery save mode off decreases battery life
by approximately 20%.
On
Restore Factory Defaults
Returns radio to its original factory settings.
---
Push to Talk S
6864110w15o.book Page 35 Thursday, February 13, 2003 9:46 PM
Symptom
Try This:
No Power
Recharge or replace Li Ion battery.
Reposition or replace Alkaline batteries.
Message not
transmitted
Make sure Push to Talk is completely pressed while
transmitting.
Recharge, replace, and/or reposition batteries.
Verify the transmit light is illuminated while speaking.
Hearing other
Frequency or interference eliminator code may be in use.
noises or
conversation on Change on all radios if possible (see page 28 and 29).
a channel
Poor audio
quality
Troubleshooting
Troubleshooting
Bandwidth does not match. For optimal audio quality when
communicating with _Series radios, the bandwidth of other
radios should be set to 12.5 kHz.
35
Troubleshooting
6864110w15o.book Page 36 Thursday, February 13, 2003 9:46 PM
36
Symptom
Try This:
Limited talk
range
Steel and/or concrete structures, heavy foliage, buildings, or
vehicles decrease range (see page 22). Check for clear line of
sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt
decreases range. Change location of radio.
Message not
received
Confirm radios have the same channel, frequency, and
interferene eliminator code settings (see page 26).
Recharge, replace, and/or reposition batteries.
Move to another location. Obstructions and operating indoors or
in vehicles may decrease range.
Verify radio is not in scan mode (CLS1410 only, see page 24).
Heavy static or
interference
Radios are too close. They must be at least 5 feet apart.
Radios are too far apart or obstacles are interfering with
transmission.
Keypad locked
Unlock by holding S for 3 seconds.
Symptom
Try This:
Low batteries
Recharge or replace batteries. Extreme operating temperatures
affect battery life.
Charger light
does not come
on
Reinsert radio and/or battery.
Clean battery and/or charger contacts.
Verify that the charging pin on the transformer is inserted
correctly into the drop-in charger.
AAA cells installed in radio. Remove and replace with Li Ion
battery.
Low battery
meter reading
although new
batteries are
installed
Verify radio is set to the correct battery type (see page 15).
Cannot activate
VOX
Feature not set and on (see page 22).
Sensitivity set to 0 (see page 23).
Cannot enter
k mode
Unplug audio accessories and retry.
Troubleshooting
6864110w15o.book Page 37 Thursday, February 13, 2003 9:46 PM
37
6864110w15o.book Page 38 Thursday, February 13, 2003 9:46 PM
Use and Care
Use and Care
XXX
Use a soft damp cloth
to clean the exterior.
Do not use alcohol or
cleaning solutions.
If the radio is submerged in water...
Turn radio off and
remove batteries.
38
Do not immerse
in water.
Dry with soft cloth.
Do not use radio until
completely dry.
6864110w15o.book Page 39 Thursday, February 13, 2003 9:46 PM
These charts provide frequency information and are useful when using Motorola
_ Series radios with other business radios. Frequency Display Number is
identical to Spirit M, GT, and S-Series frequency position (where applicable).
UHF Frequencies
Display
Number
Frequency
(MHz)
Bandwidth
464.5000
464.5500
467.7625
467.8125
467.8500
467.8750
Display
Number
Frequency
(MHz)
Bandwidth
12.5
15
461.1875
12.5
12.5
16
461.2125
12.5
12.5
17
461.2375
12.5
12.5
18
461.2625
12.5
12.5
19
461.2875
12.5
12.5
20
461.3125
12.5
467.9000
12.5
21
461.3375
12.5
467.9250
12.5
22
461.3625
12.5
461.0375
12.5
23
462.7625
12.5
10
461.0625
12.5
24
462.7875
12.5
Frequencies and Bandwidths
Frequencies and Bandwidths
39
6864110w15o.book Page 40 Thursday, February 13, 2003 9:46 PM
Frequencies and Bandwidths
UHF Frequencies (Continued)
40
Display
Number
Frequency
(MHz)
Bandwidth
Display
Number
Frequency
(MHz)
Bandwidth
11
461.0875
12.5
25
462.8125
12.5
12
461.1125
12.5
26
462.8375
12.5
13
461.1375
12.5
27
462.8625
12.5
14
461.1625
12.5
28
462.8875
12.5
29
462.9125
12.5
43
466.2625
12.5
30
464.4875
12.5
44
466.2875
12.5
31
464.5125
12.5
45
466.3125
12.5
32
464.5375
12.5
46
466.3375
12.5
33
464.5625
12.5
47
466.3625
12.5
34
466.0375
12.5
48
467.7875
12.5
35
466.0625
12.5
49
467.8375
12.5
36
466.0875
12.5
50
467.8625
12.5
37
466.1125
12.5
51
467.8875
12.5
6864110w15o.book Page 41 Thursday, February 13, 2003 9:46 PM
Display
Number
Frequency
(MHz)
Bandwidth
Display
Number
Frequency
(MHz)
Bandwidth
38
466.1375
12.5
52
467.9125
12.5
39
466.1625
12.5
53
469.4875
12.5
40
466.1875
12.5
54
469.5125
12.5
41
466.2125
12.5
55
469.5375
12.5
42
466.2375
12.5
56
469.5625
12.5
Frequencies and Bandwidths
UHF Frequencies (Continued)
41
6864110w15o.book Page 42 Thursday, February 13, 2003 9:46 PM
Frequencies and Bandwidths
Interference Eliminator Codes
Display
Number
Code
(Hz)
Display
Number
Code
(Hz)
Display
Number
Code
(Hz)
67.0
14
107.2
27
167.9
71.9
15
110.9
28
173.8
74.4
77.0
79.7
82.5
85.4
88.5
91.5
10
94.8
16
114.8
29
179.9
17
118.8
30
186.2
18
123.0
31
192.8
19
127.3
32
203.5
20
131.8
33
210.7
21
136.5
34
218.1
22
141.3
35
225.7
23
146.2
36
233.6
11
97.4
24
151.4
37
241.8
12
100.0
25
156.7
38
250.3
13
103.5
26
162.2
Carrier Squelch (0) disables interference eliminator codes.
42
6864110w15o.book Page 43 Thursday, February 13, 2003 9:46 PM
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
39
023
54
115
69
223
40
025
55
116
70
226
41
026
42
031
43
032
44
043
45
047
46
051
47
054
48
065
49
56
125
71
243
57
131
72
244
58
132
73
245
59
134
74
251
60
143
75
261
61
152
76
263
62
155
77
265
63
156
78
271
071
64
162
79
306
50
072
65
165
80
311
51
073
66
172
81
315
52
074
67
174
82
331
53
114
68
205
83
343
Frequencies and Bandwidths
Digital Interference Eliminator Codes
43
6864110w15o.book Page 44 Thursday, February 13, 2003 9:46 PM
Frequencies and Bandwidths
Digital Interference Eliminator Codes (Continued)
44
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
84
346
97
465
110
632
85
351
98
466
111
654
86
364
87
365
88
371
89
411
90
412
91
413
92
423
93
431
94
99
503
112
662
100
506
113
664
101
516
114
703
102
532
115
712
103
546
116
723
104
565
117
731
105
606
118
732
106
612
119
734
432
107
624
120
743
95
445
108
627
121
754
96
464
109
631
6864110w15o.book Page 45 Thursday, February 13, 2003 9:46 PM
The _Series radio replaces the Spirit GT Series radio. The factory default
settings for both radios are identical. However, existing radios may have been
programmed to different settings. To program your _Series radio to talk with a
Spirit GT Series radio, verify or change your Spirit GT settings as follows.
To verify the frequency and code:
1. Press the Menu button 3 times. The channel number and frequency display.
2. Press Menu again. The interference eliminator code displays.
To change the frequency:
1. Enter programming mode by pressing and holding Push to Talk for
approximately 5 seconds while turning the radio on, then release Push to Talk.
2. Use the Scroll button to select one the eight frequencies.
To change the interference eliminator code:
1. Enter programming mode by pressing and holding Push to Talk for
approximately 5 seconds while turning the radio on, then release Push to Talk.
2. Press the Menu button. The code number flashes.
3. Use the Scroll button to select the code.
Spirit GT Series Programming
Spirit GT Series Programming
To exit programming mode on a Spirit GT Series radio, press Push to Talk.
45
6864110w15o.book Page 46 Thursday, February 13, 2003 9:46 PM
Motorola Limited Warranty for the United States and Canada
Warranty
What Does this Warranty Cover?
46
Subject to the exclusions contained below, Motorola, Inc. warrants its telephones, pagers, messaging devices,
and consumer and professional two-way radios (excluding commercial, government or industrial radios) that
operate via Family Radio Service or General Mobile Radio Service, Motorola-branded or certified accessories
sold for use with these Products (“Accessories”) and Motorola software contained on CD-ROMs or other tangible
media and sold for use with these Products (“Software”) to be free from defects in materials and workmanship
under normal consumer usage for the period(s) outlined below. This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola Products, Accessories and Software purchased by consumers in
the United States or Canada, which are accompanied by this written warranty:
Products and Accessories
Products Covered
Products and Accessories as defined above,
unless otherwise provided for below.
Length of Coverage
One (1) year from the date of purchase by the first
consumer purchaser of the product unless otherwise
provided for below.
Decorative Accessories and Cases. Decorative Limited lifetime warranty for the lifetime of ownership by
covers, bezels, PhoneWrap™ covers and cases. the first consumer purchaser of the product.
Monaural Headsets. Ear buds and boom
Limited lifetime warranty for the lifetime of ownership by
headsets that transmit mono sound through a
the first consumer purchaser of the product.
wired connection.
6864110w15o.book Page 47 Thursday, February 13, 2003 9:46 PM
Length of Coverage
Ninety (90) days from the date of purchase by the first
consumer purchaser of the product.
The balance of the original warranty or for ninety (90)
days from the date returned to the consumer, whichever
is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that
leak are covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse,
accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting
from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product
or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded
from coverage.
Use of Non-Motorola Products and Accessories. Defects or damage that result from the use of Non-Motorola
branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in any way by someone other than Motorola, or its
authorized service centers, are excluded from coverage.
Warranty
Products Covered
Consumer and Professional Two-Way Radio
Accessories.
Products and Accessories that are Repaired or
Replaced.
47
6864110w15o.book Page 48 Thursday, February 13, 2003 9:46 PM
Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed,
altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial
numbers; or (d) nonconforming or non-Motorola housings, or parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any
communication service or signal you may subscribe to or use with the Products Accessories or Software is
excluded from coverage.
Warranty
Software
Products Covered
Length of Coverage
Software. Applies only to physical defects in the Ninety (90) days from the date of purchase.
media that embodies the copy of the software (e.g.
CD-ROM, or floppy disk).
Exclusions
Software Embodied in Physical Media. No warranty is made that the software will meet your requirements or
will work in combination with any hardware or software applications provided by third parties, that the operation
of the software products will be uninterrupted or error free, or that all defects in the software products will be
corrected.
Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software
that is downloaded from the internet), is provided “as is” and without warranty.
Who is Covered?
This warranty extends only to the first consumer purchaser, and is not transferable.
48
6864110w15o.book Page 49 Thursday, February 13, 2003 9:46 PM
What Will Motorola Do?
Motorola, at its option, will at no charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty. We may use functionally equivalent
reconditioned/refurbished/pre-owned or new Products, Accessories or parts. No data, software or applications
added to your Product, Accessory or Software, including but not limited to personal contacts, games and ringer
tones, will be reinstalled. To avoid losing such data, software and applications please create a back up prior to
requesting service.
USA
Phones 1-800-331-6456
Pagers 1-800-548-9954
Two-Way Radios 1-800-448-6686
Canada All Products 1-800-461-4575
TTY
TTY 1-888-390-6456
For Accessories and Software, please call the telephone number
designated above for the product with which they are used.
Warranty
How to Obtain Warranty Service or Other Information
You will receive instructions on how to ship the Products, Accessories or Software, at your expense, to a
Motorola Authorized Repair Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or
other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service
provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly;
(e) your address and telephone number.
49
6864110w15o.book Page 50 Thursday, February 13, 2003 9:46 PM
Warranty
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO
EVENT SHALL MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE)
FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR
SOFTWARE, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA,
SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE
FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential
damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights that
vary from state to state or from one jurisdiction to another.
Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted
Motorola software such as the exclusive rights to reproduce and distribute copies of the Motorola software.
Motorola software may only be copied into, used in, and redistributed with, the Products associated with such
Motorola software. No other use, including without limitation disassembly of such Motorola software or exercise
of the exclusive rights reserved for Motorola, is permitted.
50
6864110w15o.book Page 51 Thursday, February 13, 2003 9:46 PM
_Series Programming Quick Reference
To enter programming mode, press and hold Push to Talk
and Qfor 3 seconds while turning the radio on. The radio
beeps and displays k, the channel number flashes, and the
frequency (indicated by l) and code (indicated by y)
display alternately.
Set the
Channel*
Set the
Frequency
Set the
Interference
Eliminator
Code
Set
Available
Channels*
* CLS1410 Only
Press [ or
].
Press S until l displays.
Press [ or ] to change the
frequency.
Press S until y
displays.Press [or ] to change
the code.
Press S until = displays.
Press [ or ] to select
number of available channels.
6864110w15o.book Page 52 Thursday, February 13, 2003 9:46 PM
_Series Programming Quick Reference
Press S until E display.s
Set a Call
Tone
Press [ or ] to select1, 2, or
3 for audible call tones, 4 for
VibraCall, or 0 for off (default).
Press S until g and ? display.
Set the
Microphone
Gain
Press [ or ] to select:
1 Low sensitivity
2 Medium sensitivity
3 High sensitivity
Press S until h displays and the
channel number and Y or n flash.
Edit the
Scan List*
Press [ or ] to select the
channel, then press T to select Y
(include channel) or n (exclude
channel).
6864110w15o.book Page 53 Thursday, February 13, 2003 9:46 PM
motorola.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:02:14 03:45:24Z
Modify Date                     : 2003:03:13 13:55:00-05:00
Page Count                      : 55
Creation Date                   : 2003:02:14 03:45:24Z
Mod Date                        : 2003:03:13 13:55:00-05:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : fdr049
Metadata Date                   : 2003:03:13 13:55:00-05:00
Creator                         : fdr049
Title                           : 6864110w15o.book

EXIF Metadata provided by EXIF.tools