Motorola Solutions 89FT4882 PORTABLE 2-WAY RADIO User Manual 63M01 A BRUS en

Motorola Solutions, Inc. PORTABLE 2-WAY RADIO 63M01 A BRUS en

USERS MANUAL

Download: Motorola Solutions 89FT4882 PORTABLE 2-WAY RADIO User Manual 63M01 A BRUS en
Mirror Download [FCC.gov]Motorola Solutions 89FT4882 PORTABLE 2-WAY RADIO User Manual 63M01 A BRUS en
Document ID873597
Application IDx7Jv+C9a+sTH5TrjRzX74g==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize246.54kB (3081769 bits)
Date Submitted2007-11-29 00:00:00
Date Available2007-11-29 00:00:00
Creation Date2007-10-05 17:09:46
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2007-10-05 17:55:55
Document Title63M01_A_BRUS_en.book
Document CreatorFrameMaker 7.1
Document Author: cei004

Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are Trademarks of Motorola,
Inc. Reg. U.S. Pat. & Tm. Off. © 2007 Motorola, Inc. All rights reserved.
CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package Contents . . . . . . . . . . . . . . . . . . . . . .5
Batteries and Chargers Safety
Information. . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operational Safety Guidelines. . . . . . . . . . . . .8
FCC Licensing Information . . . . . . . . . . . . 9
Interference Information . . . . . . . . . . . . . . . . .9
Radio Overview . . . . . . . . . . . . . . . . . . . . . 11
Parts of the Radio . . . . . . . . . . . . . . . . . . . . .11
On/Off/Volume Knob. . . . . . . . . . . . . . . .12
Channel Selector Knob . . . . . . . . . . . . . .12
Accessory Connector . . . . . . . . . . . . . . .12
Model Label . . . . . . . . . . . . . . . . . . . . . .12
Microphone . . . . . . . . . . . . . . . . . . . . . . .12
Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .12
12
12
12
14
14
15
16
CONTENTS
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
LED Indicator . . . . . . . . . . . . . . . . . . . . .
Side Buttons . . . . . . . . . . . . . . . . . . . . .
The Lithium-Ion (Li-Ion) Battery . . . . . . .
Battery Features. . . . . . . . . . . . . . . . . . . . . .
About the Li-Ion Battery . . . . . . . . . . . . .
Battery Recycling and Disposal . . . . . . .
Installing the Lithium-Ion (Li-Ion)
Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Lithium-Ion (Li-Ion)
Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
Alkaline Battery Pack (Optional
Accessory) . . . . . . . . . . . . . . . . . . . . . . .
Installing Alkaline Batteries . . . . . . . . . .
Removing Alkaline Batteries . . . . . . . . .
Attaching and Removing Antenna . . . . .
Attaching the Antenna . . . . . . . . . . . . . .
Removing the Antenna . . . . . . . . . . . . .
Installing Spring Action Belt Clip . . . . . .
Power Supply, Adaptor and Drop-in
Tray Charger . . . . . . . . . . . . . . . . . . . . .
Battery Life Information . . . . . . . . . . . . .
Alkaline Battery Life . . . . . . . . . . . . . . . .
Charging the Battery . . . . . . . . . . . . . . .
16
17
17
17
18
18
18
19
19
20
21
22
English
CONTENTS
Getting Started . . . . . . . . . . . . . . . . . . . . . 29
Turning radio ON/OFF. . . . . . . . . . . . . . . . . .29
Adjusting Volume . . . . . . . . . . . . . . . . . . . . .29
Selecting a Channel . . . . . . . . . . . . . . . . . . .29
Talking and Monitoring . . . . . . . . . . . . . . . . .29
Receiving a Call . . . . . . . . . . . . . . . . . . . . . .30
Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .30
Radio LED Indicators . . . . . . . . . . . . . . . . . .32
Hands-Free Use/VOX . . . . . . . . . . . . . . . . . .33
With Compatible VOX Accessories. . . . .33
Setting VOX Sensitivity . . . . . . . . . . . . . .34
Microphone Gain. . . . . . . . . . . . . . . . . . .34
Battery Save . . . . . . . . . . . . . . . . . . . . . .34
Reset to Factory Defaults . . . . . . . . . . . .34
End of Transmission Tone (Roger
Beep Tone) . . . . . . . . . . . . . . . . . . . . . . .35
Programming Features . . . . . . . . . . . . . . . 36
Programming Mode. . . . . . . . . . . . . . . . . . . .36
Learning to Read the Values the
Radio Signals You . . . . . . . . . . . . . . . . .36
Entering Programming Mode . . . . . . . . .39
Reading Frequencies Values . . . . . . . . .39
English
Reading CTCSS/DPL Values . . . . . . . .
Reading Auto-Scan Values . . . . . . . . . .
Programming Frequencies, Codes and
Auto-Scan . . . . . . . . . . . . . . . . . . . . . . .
Programming Mode FAQ . . . . . . . . . . . .
Programming Values Example. . . . . . . . . . .
Example of Programming a Frequency .
Example of Programming a Code . . . . .
Example of Programming Auto-Scan . .
Other Programming Features . . . . . . . . . . .
Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Scan List . . . . . . . . . . . . . . . . . .
Nuisance Channel Delete . . . . . . . . . . .
CPS (Computer Programming Software) . . .
Bandwidth Select . . . . . . . . . . . . . . . . . .
Time-Out Timer . . . . . . . . . . . . . . . . . . .
Power Select . . . . . . . . . . . . . . . . . . . . .
Battery Type Setting . . . . . . . . . . . . . . .
Call Tones . . . . . . . . . . . . . . . . . . . . . . .
Scramble L. . . . . . . . . . . . . . . . . . . . . . .
Reverse Burst . . . . . . . . . . . . . . . . . . . .
Cloning Radios. . . . . . . . . . . . . . . . . . . . . . .
40
41
41
42
43
43
44
45
46
46
47
47
48
49
49
49
49
49
50
50
51
Troubleshooting . . . . . . . . . . . . . . . . . . . . 56
Use and Care . . . . . . . . . . . . . . . . . . . . . . . 60
Frequency and Code Charts . . . . . . . . . . 61
RDX VHF Frequencies Chart . . . . . . . . . . . .61
RDV2020 - VHF Default Frequencies
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Making XTN Compatible with RDX
Radios - Quick Instructions . . . . . . . . . . . . . .64
RDV5100 - VHF Default Frequencies
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
RDX UHF Frequencies Chart . . . . . . . . . . . .66
RDU2020 - UHF Default Frequencies
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
RDU4100 - UHF Default Frequencies
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
CTCSS and PL/DPL Codes . . . . . . . . . . . . . 72
Programming Customized Frequencies
on 4W/5W RDX models . . . . . . . . . . . . . . . . 75
Motorola Limited Warranty for the
United States and Canada. . . . . . . . . . . . . 76
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 80
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Accessories . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carry Accessories . . . . . . . . . . . . . . . . . . . .
Power Supplies AC Pin Adaptors. . . . . . . . .
Software Applications. . . . . . . . . . . . . . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supplies . . . . . . . . . . . . . . . . . . . . . .
80
80
80
81
81
81
81
81
82
CONTENTS
Cloning with a Multi Unit Charger
(MUC) . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Cloning Radio using the Radio to
Radio (R2R) Cloning Cable
(Optional Accessory). . . . . . . . . . . . . . . .53
Cloning using the CPS (Computer
Programming Software) . . . . . . . . . . . . .55
RDX Series™ Features Summary. . . . . . . 83
Programmable Buttons Chart . . . . . . . . . 92
Icons Chart . . . . . . . . . . . . . . . . . . . . . . . . . 93
English
SAFETY
PRODUCT SAFETY AND RF
EXPOSURE COMPLIANCE
SAFETY
Caution
Before using this product,
read the operating
instructions and RF energy
awareness information
contained in the Product
Safety and RF Exposure
booklet enclosed with your
radio.
ATTENTION!
This radio is restricted to occupational use only
to satisfy FCC RF energy exposure
requirements.
English
For a list of Motorola-approved antennas,
batteries, and other accessories, visit the
following website which lists approved
accessories:
http://www.motorola.com/RDX
INTRODUCTION
Business Radios,
RPSD 1C15, Motorola
Thank you for purchasing the Motorola® RDX
Series™ Radio. This radio is a product of
Motorola's 75 plus years of experience as a
world leader in the designing and
manufacturing of communications equipment.
The RDX Series™ radios provide cost-effective
communications for businesses such as retail
stores, restaurants, schools, construction sites,
manufacturing, property and hotel
management and more. Motorola professional
two-way radios are the perfect communications
solution for all of today's fast-paced industries.
8000 West Sunrise Boulevard
Note:
PACKAGE CONTENTS
•
Radio
•
Antenna (only for RDU4100 and RDV5100)
•
Spring Action Belt-Clip
•
Lithium-Ion Battery
•
Power Supply
•
User Guide
•
Warranty Card
•
Drop-in Tray Charger
•
Product Safety & RF Exposure Booklet
INTRODUCTION
Read this user guide carefully to ensure you
know how to properly operate the radio
before use
Plantation, Florida 33322
English
For a copy of a large-print version of this user
guide or for product-related questions, contact:
For product information visit us at:
www.motorola.com/radios/business
1-800-448-6686 in the USA
or visit our microsite at:
www.motorola.com/RDX
1-800-461-4575 in Canada
INTRODUCTION
1-866-522-5210 on your TTY (Text
Telephone)
English
3.
and cord, pull by the plug rather than the cord
when disconnecting the charger.
4.
extension cord could result in risk of fire and
electric shock. If an extension cord must be
used, make sure that the cord size is 18AWG
Before using the battery charger, read all the
instructions and cautionary markings on
the charger,
•
the battery, and
•
the radio using the battery
1.
To reduce risk of injury, charge only the
for lengths up to 100 feet (30.48 m), and
16AWG for lengths up to 150 feet (45.72 m).
5.
To reduce risk of fire, electric shock, or injury, do
not operate the charger if it has been broken or
damaged in any way. Take it to a qualified
Motorola service representative.
6.
Do not disassemble the charger; it is not
rechargeable Motorola-authorized batteries.
repairable and replacement parts are not
Other batteries may explode, causing personal
available. Disassembly of the charger may
injury and damage.
2.
An extension cord should not be used unless
absolutely necessary. Use of an improper
This document contains important safety and
operating instructions. Read these instructions
carefully and save them for future reference.
•
To reduce risk of damage to the electric plug
Use of accessories not recommended by
BATTERIES AND CHARGERS
SAFETY INFORMATION
BATTERIES AND
CHARGERS SAFETY
INFORMATION
result in risk of electrical shock or fire.
7.
To reduce risk of electric shock, unplug the
Motorola may result in risk of fire, electric
charger from the AC outlet before attempting
shock, or injury.
any maintenance or cleaning
English
BATTERIES AND CHARGERS
SAFETY INFORMATION
OPERATIONAL SAFETY
GUIDELINES
•
Turn the radio OFF when charging battery.
•
The charger is not suitable for outdoor use. Use
only in dry locations/conditions.
•
supply equipment must not exceed 40°C (104°F).
•
Power output from the power supply unit must not
exceed the ratings stated on the product label
located at the bottom of the charger.
•
Make sure that the cord is located where it will
not be stepped on, tripped over, or subjected to
and wired supply of the correct voltage (as
water, damage, or stress.
Disconnect charger from line voltage by removing
main plug.
•
The outlet to which this equipment is connected
•
In equipment using fuses, replacements must
should be nearby and easily accessible.
comply with the type and rating specified in the
equipment instructions.
English
Maximum ambient temperature around the power
Connect charger only to an appropriately fused
specified on the product).
•
•
(FCC). To transmit on these frequencies, you
FCC LICENSING
INFORMATION
are required to have a license issued by the
FCC. Application is made available on FCC
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC
Form 601 and Schedules D, H, and Remittance
Form 159.
To obtain these FCC forms, request document
this device does not cause harmful
000601 which includes all forms and
interference.
instructions. If you wish to have the document
RDX Series™ professional two-way radios
operate on radio frequencies that are regulated
faxed, mailed or have questions, use the
following contact information.
by the Federal Communications Commission
Faxed contact the
Fax-On- Demand
system at:
1-202-418-0177
Mailed call the FCC forms hotline at:
1-800-418-FORM
1-800-418-3676
Questions regarding FCC
license contact the FCC at:
FCC LICENSING
INFORMATION
Rules. Operation is subject to the condition that
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
English
Before filling out your application, you must
Replacement of any transmitter component
decide which frequency(ies) you can operate
(crystal, semiconductor, etc.) not authorized by
on. See “Frequencies and Code Charts”. For
the FCC equipment authorization for this radio
questions on determining the radio frequency,
could violate FCC rules.
FCC LICENSING
INFORMATION
call Motorola Product Services at:
was intended to be distributed is subject to
Changes or modifications not expressly
government regulations and may be prohibited
approved by Motorola may void the user’s
authority granted by the FCC to operate this
radio and should not be made. To comply with
FCC requirements, transmitter adjustments
should be made only by or under the
supervision of a person certified as technically
qualified to perform transmitter maintenance
and repairs in the private land mobile and fixed
services as certified by an organization
representative of the user of those services.
English
Use of this radio outside the country where it
1-800-448-6686
10
RADIO OVERVIEW
PARTS OF THE RADIO
Antenna
Microphone
Channel Selector
Knob
On/Off/Volume
Knob
LED Indicator
PTT Button
SB1-Monitor
Button
Model Label
Lithium-Ion
Battery
SB2- Scan/
Nuisance
Channel
Delete
11
RADIO OVERVIEW
Accessory
Connector
English
On/Off/Volume Knob
Side Buttons
Used to turn the radio ON or OFF and to adjust
the radio’s volume.
Push-to-Talk (PTT) Button
•
Channel Selector Knob
Used to switch the radio to different channels.
Side Button 1 (SB1)
•
Accessory Connector
Used to connect compatible audio accessories.
RADIO OVERVIEW
The Side Button 1 is a general button that can be
configured by the Computer Programming
Software - CPS. The default setting of SB1 is
‘Monitor’.
Model Label
Side Button 2 (SB2)
Indicates the model of the radio.
•
Microphone
English
Press and hold down this button to talk, release it
to listen.
Speaks clearly into the microphone when
sending a message.
Antenna
For models RDU2020, and RDV2020 the
antennas are non-removable. For RDV5100,
RDU4100 antennas are removable.
LED Indicator
Used to give battery status, power-up status,
radio call information and scan status.
12
The Side Button 2 is a general button that can be
configured by the CPS. The SB2 default setting is
‘Scan/Nuisance Channel Delete’.
The Lithium-Ion (Li-Ion) Battery
RDX Series™ provides different types of
batteries. For more information, see “Battery
Features” on page 14.
This User Guide covers multiple RDX Series™
models, and may detail some features your
radio does not have. The radio’s model is
shown on the front of the radio, underneath the
speaker, and provides you the following
information:
Model
Frequency
Band
Transmit
Power
(Watts)
Number of
Channels
Antenna
RDV2020
VHF
Non-removable
RDU2020
UHF
Non-removable
RDU4100
UHF
10
removable
RDV5100
VHF
10
removable
RADIO OVERVIEW
13
English
BATTERY FEATURES
RDX Series™ radios provide Lithium-Ion
batteries that come in different capacities that
will define the battery life. It also offers the
option to use Alkaline batteries.
About the Li-Ion Battery
RADIO OVERVIEW
The RDX Series™ radio comes equipped with
a rechargeable Li-Ion battery. This battery
should be charged before initial use to ensure
optimum capacity and performance.
English
Battery life is determined by several factors.
Among the more critical are the regular
overcharge of batteries and the average depth
of discharge with each cycle. Typically, the
greater the overcharge and the deeper the
average discharge, the fewer cycles a battery
will last. For example, a battery which is
overcharged and discharged 100% several
times a day, lasts fewer cycles than a battery
that receives less of an overcharge and is
discharged to 50% per day. Further, a battery
14
which receives minimal overcharging and
averages only 25% discharge, lasts even
longer.
Motorola batteries are designed specifically to
be used with a Motorola charger and vice
versa. Charging in non-Motorola equipment
may lead to battery damage and void the
battery warranty. The battery should be at
about 77°F (25°C) (room temperature),
whenever possible. Charging a cold battery
(below 50° F [10°C]) may result in leakage of
electrolyte and ultimately in failure of the
battery. Charging a hot battery (above 95°F
[35°C]) results in reduced discharge capacity,
affecting the performance of the radio.
Motorola rapid-rate battery chargers contain a
temperature-sensing circuit to ensure that
batteries are charged within the temperature
limits stated above.
Battery Recycling and Disposal
Many retailers and dealers participate in this
program. For the location of the drop-off facility
closest to you, access RBRC's Internet web
site at:
www.rbrc.com
or call:
1-800-8-BATTERY
This internet site and telephone number also
provides other useful information concerning
recycling options for consumers, businesses
and governmental agencies.
RADIO OVERVIEW
Li-Ion rechargeable batteries can be recycled.
However, recycling facilities may not be
available in all areas. Under various U.S. state
laws and the laws of several other countries,
batteries must be recycled and cannot be
disposed of in landfills or incinerators. Contact
your local waste management agency for
specific requirements and information in your
area. Motorola fully endorses and encourages
the recycling of Li-Ion batteries. In the U.S. and
Canada, Motorola participates in the
nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for Li-Ion battery
collection and recycling.
15
English
Installing the Lithium-Ion (Li-Ion) Battery
Removing the Lithium-Ion (Li-Ion) Battery
Battery
Latch
Battery
Latch
RADIO OVERVIEW
slots
English
1.
Turn OFF the radio.
1.
Turn OFF the radio.
2.
With the Motorola logo side up on the battery
2.
Push down the battery latch and hold it
pack, fit the tabs at the bottom of the battery
into the slots at the bottom of the radio’s body.
3.
Press the top part of the battery towards the
radio until a click is heard.
Note:
To learn about the Li-Ion Battery Life
features, refer to “About the Li-Ion Battery”
on page 14
16
depressed while removing the battery.
3.
Pull the battery away from the radio.
Alkaline Battery Pack (Optional Accessory)
Removing Alkaline Batteries
Installing Alkaline Batteries
Alkaline
Battery
Door
Turn OFF the radio, if it is turned ON.
2.
Remove Li-Ion battery.
3.
Assemble alkaline battery pack in the same
steps as installing the Li-Ion battery pack.
4.
Remove battery door from alkaline battery pack.
5.
Slide the 5 AA alkaline batteries into the frame,
1.
Turn OFF the radio, if it is turned ON.
2.
Slide the battery latches, on both sides of the
battery, downwards.
3.
Pull the top of the battery away from the radio’s
body, and lift the battery from the radio’s body.
matching the markings inside the compartment
17
RADIO OVERVIEW
1.
Alkaline
Battery
Door
English
Attaching and Removing Antenna
RADIO OVERVIEW
These instructions apply ONLY to models RDU4100 and RDV5100. Do not attempt to remove the
antenna if your radio is not one of these models.
English
Attaching the Antenna
Removing the Antenna
1.
1.
Align the threaded end of the antenna with the
radio’s antenna connector.
2.
Turn the antenna clockwise to fasten it.
18
Turn the antenna counterclockwise until you
can remove it.
Installing Spring Action Belt Clip
Power Supply, Adaptor and Drop-in Tray
Charger
Belt Clip
Tab
Power Supply
Spring
Action Belt
Clip
1.
Slide the spring action belt clip rails into the belt
Drop-in Tray Charger
The radio is equipped with one Drop-in Tray
Charger and one Power Supply with Adaptor.
For details, see “Chargers” on page 81.
clip grooves on the back of the battery pack and
RADIO OVERVIEW
slide it down until the belt clip tab snaps into
place.
2.
To remove, pull back the metal release tab on
the belt clip tab and push the spring action belt
clip upward to remove.
19
English
Battery Life Information
When the Battery Save feature is ON (enabled by default) the battery life will be longer. The
following chart summarizes battery life estimations:
Li-Ion Battery Life with Battery Save feature ON
RADIO OVERVIEW
Battery Type
English
4 Watts
2 Watts
Standard
8.5 hours
8.5 hours
12 hours
High
17 hours
17 hours
24 hours
Ultra High
18.5 hours
18.5 hours
26 hours
Note:
20
5 Watts
Battery life is estimated based on 5% transmit/ 5% receive/ 90% standby
standard duty cycle
Alkaline Battery Life
The following chart estimates the Alkaline battery life:
Alkaline Battery Life
Battery Save Feature
ON
5 Watts
26 hours*
4 Watts
26 hours*
2 Watts
26 hours
Notes:
•
Battery life are being estimated based on 5% transmit/ 5% receive/ 90% standby
standard duty cycle.
* When using Alkaline battery, the radio is set to 2W by default
RADIO OVERVIEW
•
21
English
Charging the Battery
RDX Series™ offers two types of chargers :
•
Standard Charger and,
•
Rapid Charger.
Note:
Charging with the Drop-in Tray
Single Unit Charger (SUC)
Power Supply
(Transformer)
The radio comes equipped with a Standard
Charger
To charge the battery (with the radio attached),
place it in a Motorola-approved Drop-in Tray
Single Unit Charger or Drop-in Tray Multi Unit
Charger.
RADIO OVERVIEW
Note:
English
When acquiring additional chargers or
power supplies, make sure you have similar
drop-in tray chargers and power supplies
sets (all “rapid” or all “standard”). For part
number details, refer to “Chargers” on
page 81
Drop-in Tray
Charger Port
Drop-in Tray Charger
1.
Place the drop-in tray charger on a flat surface.
2.
Insert the connector of the power supply into the
port on the side of the drop-in tray charger.
3.
Plug the AC adaptor into a power outlet.
4.
Insert the radio into the tray with the front of the
radio facing the front of the charger, as shown.
Note:
22
When charging a battery attached to a radio,
turn the radio OFF to ensure a full charge.
See “Operational Safety Guidelines” on
page 8 for more information
Charging a Standalone Battery
Charging a Standard Battery
The drop-in tray charger has a removable
bracket that is adjustable depending on the
type of battery that needs to be charged. It is
designed to charge either the battery (with the
radio) or a standalone battery. The drop-in tray
charger's default position will charge a
standard battery. The following image shows
the orientation for each battery:
Note:
Ensure that the bracket in the charger is
adjusted to the correct position for either
Standard or High capacity battery. See
“Charging a Standard Battery” on page 23
Adjustable bracket
Standard
Figure 1:
Adjustable bracket
High and Ultra High Capacity
Identifying the Drop-In Charger’s Position Before
Charging the Battery
23
RADIO OVERVIEW
To charge only the battery - at step 4, insert the
battery into the tray, with the inside surface of
the battery facing the front of the charger, as
shown. Ensure the slots in the battery correctly
engage in the charger
English
Charging a High Capacity or Ultra
High Capacity Battery
3.
Repeat same procedure to return to the
charging a Standard Battery position. Label on
the removable bracket should show ‘Standard
Removable
Piece
Removable
Piece
Battery’ facing front.
Turn around
horizontal
180 degree
RADIO OVERVIEW
To convert the charger from the default setup to
accommodate the High capacity or Ultra High
capacity battery:
1.
Squeeze both tabs on each side of the
removable bracket in the drop-in charger tray
and lift the bracket from the charger tray.
2.
Rotate the removable bracket 180 degrees and
replace it by fitting it in the charger slot until it
snaps. The label on the removable bracket
should show ‘High & Ultra Capacity Battery’
facing front of the charger.
English
24
Note:
Make sure the bracket is assembled
correctly for both standalone battery and
battery (with radio)
Drop-in Tray Charger LED Indicators
Standard Charger LED Indicator
Status
LED Status
Comments
Power ON
Steady red indication for 3
seconds
The charger has powered up
Charging
Blinking red (slow)
The charger is currently charging
Charging
Complete
Steady red indication
Battery is fully charged
Battery Fault(*)
Blinking red (fast)
Battery had a fault when battery was inserted
Notes:
•
(*) Normally re-seating the battery pack will correct this issue.
•
(**) Battery temperature is too warm or too cold or wrong power supply is being used
RADIO OVERVIEW
25
English
Rapid Charger LED Indicator
Status
LED Status
Comments
Power ON
Steady green indication for 3
The charger has powered up
seconds
Charging
Blinking green
The charger is currently charging
Top-off Charging Blinking green (slow)
Battery is near fully charged
Charge
Complete
Steady green indication
Battery is fully charged
Battery Fault (*)
Blinking red (fast)
Battery has a fault when battery was inserted
Waiting to
Charge (**)
Double-blink yellow
indications
Battery charging conditions not suitable
RADIO OVERVIEW
Notes:
English
•
(*) Normally re-seating the battery pack will correct this issue.
•
(**) Battery temperature is too warm or too cold or wrong power supply is being used
26
Estimated Charging Time
The following table provides the estimated charging time of the battery. For further details, see
“Battery” on page 80.
Estimated Charging Time
Battery Type
Charging
Solution
High Capacity
Ultra High
Capacity
Standard Charging
Solution
7 hours
12 hours
13 hours
Rapid Charging
Solution
1.5 hours
3 hours
3.5 hours
RADIO OVERVIEW
Standard
27
English
Charging a Radio and Battery using
a Multi Unit Charger- MUC (Optional
Accessory)
Notes:
•
This Multi Unit Charger also allows you to clone
up to 3 radios (3 Source radios and 3 Target
radios). Refer to page 51 for details.
•
Further details on MUC’s operation are explained
in the Instructions Sheet provided with the MUC.
For part number details, refer to the Accessories
RADIO OVERVIEW
section.
The Multi Unit Charger (MUC) allows drop-in
charging of up to 6 radios or batteries. Batteries
can be charged with the radios or removed and
placed in the MUC separately. Each of the 6
charging pockets can hold a radio or battery,
but not both.
1.
Place the charger on a flat surface.
2.
Insert the power cord plug into the MUC’s jack.
3.
Plug the cord into an AC outlet.
4.
Turn the radio OFF.
5.
Set removable bracket for battery type.
6.
Insert the radio or battery into the charging
pocket.
English
28
MUC LED Indicator
Status
LED Status
Comments
Charging
Steady Red
Indication
The charger is
currently charging
Charge
Complete
Steady Green
Indication
Battery is fully
charged
Battery
Fault (*)
Blinking red
(fast)
Battery was faulty
when inserted
Note:
(*) Normally re-seating the battery pack
will correct this issue.
For the following explanations, refer to “Parts of
the Radio” on page 11.
TURNING RADIO ON/OFF
To turn ON the radio, rotate the On/Off/Volume
Knob clockwise. The radio will chirp and the
LED Indicator will briefly blink red.
SELECTING A CHANNEL
To select a channel, rotate the Channel
Selector Knob and select the desired channel
number.
GETTING STARTED
GETTING STARTED
Program each channel separately. Each
channel has its own Frequency, Interference
Eliminator Code and Scan Settings.
TALKING AND MONITORING
To turn the radio OFF, rotate the On/Off/Volume
Knob counterclockwise until you hear a ‘click’
and the radio LED Indicator turns OFF.
It is important to monitor for traffic before
transmitting to avoid ‘talking over’ someone
who is already transmitting
ADJUSTING VOLUME
To monitor, long press and hold the SB1(*)
button to access channel traffic. If no activity is
present, you will hear ‘static’. To release, press
SB1 again. Once channel traffic has cleared,
proceed with your call by pressing the PTT
button. When transmitting, the LED Indicator
will blink red every 3 seconds.
Turn the On/Off/Volume Knob clockwise to
increase the volume, or counterclockwise to
decrease the volume.
Note:
Do not hold the radio too close to the ear
when the volume is high or when adjusting
the volume
29
English
TALK RANGE
GETTING STARTED
Notes:
•
To listen to all activity on a current channel, short
This feature is called ‘CTCSS/DPL Defeat
(Squelch set to SILENT)’.
•
(*) This assumes SB1 is not being programmed
for a different mode.
Industrial
Model
Multi-Level
Inside steel/concrete Inside multi-level
Industrial buildings
buildings
RECEIVING A CALL
UHF 4W Up to 350,000 Sq. Ft.
Up to 30 Floors
1.
VHF 5W Up to 300,000 Sq. Ft.
Up to 18 Floors
UHF 2W Up to 250,000 Sq. Ft.
Up to 20 Floors
Select a channel by rotating the Channel
Selector Knob until you reach the desired
channel.
2.
Make sure the PTT button is released and listen
for voice activity.
3.
The LED Indicator blinks red while the radio is
4.
To respond, hold the radio vertically 1 to 2
receiving a call.
inches (2.5 to 5cm) from mouth. Press the PTT
button to talk; release it to listen.
English
TALK RANGE
press the SB1 to set the CTCSS/DPL code to 0.
30
VHF 2W Up to 220,000 Sq. Ft. Up to 13 Floors
1.
Channel: Current channel that the radio is
using, depending on radio model.
2.
Frequency: The frequency the radio uses to
3.
Interference Eliminator Code: These codes
transmit/receive.
4.
Scramble Code: Codes that make the
transmissions sound garbled to anyone
listening who is not set to that specific code.
5.
Bandwidth: Some frequencies have selectable
channel spacing, which must match other
radios for optimum audio quality.
For details on how to set up frequencies and
CTCSS/DPL codes in the channels, refer to
“Programming Selection Mode” in page 36.
GETTING STARTED
To establish a proper two-way communication,
the channel, frequency, and interference
eliminator codes must be the same on both
radios. This depends on the stored profile that
has been preprogrammed on the radio:
help minimize interference by providing a
choice of code combinations.
31
English
GETTING STARTED
RADIO LED INDICATORS
RADIO STATUS
Channel Alias Edit
Red heartbeat
Channel Busy
Solid orange
Cloning Mode
Two orange heartbeats
Cloning In Progress
Solid orange
Fatal Error at Power up
One green blink, one orange blink, one green blink, then repeat for 4
seconds
Low Battery
Orange blink
Low Battery Shutdown
Orange heartbeat
Monitor
LED is OFF
Power-Up
Solid red for 2 seconds
‘Idle’ Programming Mode /
Channel Mode
Green heartbeat
Scan Mode
Red heartbeat
Transmit (Tx)/Receive (RX)
Red heartbeat
Transmit in Low Power Select
Orange heartbeat
Note:
English
LED INDICATION
32
Channel Alias Edit only applies to Display Models
HANDS-FREE USE/VOX
Turn the radio OFF.
2.
Open accessory cover.
3.
Insert the audio accessory’s plug firmly into
accessory port.
4.
Turn radio ON. The LED Indicator will blink
double red
5.
Lower radio volume BEFORE placing
accessory near ear.
VOX
Accessory
Accessory
Port/
Connector
Motorola RDX Series™ radios can operate
hands-free (VOX) when used with compatible
VOX accessories.
With Compatible VOX Accessories
6.
GETTING STARTED
1.
To transmit, speak into accessory microphone
and to receive, stop talking.
7.
VOX can be temporarily disabled by pressing
the PTT button or by removing the audio
accessory.
Note:
To order accessories, refer to:
www.motorola.com/radios/professional,
call 1 (800) 448-6686, or contact your
Motorola point of purchase
The default factory setting for VOX sensitivity
level is OFF (level ‘0’). Before using VOX, set
VOX level to a level different from ‘0’ via the
CPS. Then, perform the following steps:
33
English
GETTING STARTED
Setting VOX Sensitivity
Battery Save
The sensitivity of the radio's accessory or
microphone can be adjusted to suit different
operating environments. VOX sensitivity can
be programmed via the CPS.
Battery Save feature extends battery life as
your radio goes into ‘Idle’ state. To enable/
disable press SB1 and SB2 buttons
simultaneously for 2 or 3 seconds while
powering up the radio until you hear a quick
series of beeps. To have a slightly better attack
time, set Battery Save feature to OFF so that
the radio is always ready to transmit or receive
without any delays.
Default value is OFF (level 0). If you want to
use the VOX feature, VOX level should be set
at a level different from 0.
•
1 = Low sensitivity
•
2 = Medium sensitivity
•
3 = High sensitivity
Microphone Gain
The sensitivity of the microphone can be
adjusted to fit different users or operating
environments.
This feature can be adjusted only through the
CPS. Microphone default setting is set to level
2 (medium gain).
English
34
Note:
Battery Save feature is set to ON by default
Reset to Factory Defaults
Reset to Factory Defaults will set back all radio
features to the original factory default settings.
To do so, press PTT, SB2 and SB1
simultaneously while turning ON the radio until
you hear a high tone chirp.
GETTING STARTED
End of Transmission Tone (Roger Beep
Tone)
To enable/disable End of Transmission Tone,
short press the SB1 button while turning ON
the radio .
Note:
This setting is set to OFF by default
35
English
PROGRAMMING
FEATURES
PROGRAMMING
FEATURES
To easily program all the features in your radio,
it is recommended to use the CPS
Programming Cable and CPS software.
CPS software download is available for free at
www.motorola.com/RDX
PROGRAMMING MODE
Programming Mode is a special radio mode to
program basic radio's features by using the
radio’s panel.
When the radio is set to Programming Mode,
you are able to read and modify three features:
The Auto-Scan feature allows you to set a
particular channel to automatically enable Scan
each time you switch to that channel.
Learning to Read the Values the Radio
Signals You
As the non-display model does not have a
display to show the values that are being
programmed, the radio will communicate this
information using beeps and LED indications.
The radio's LEDs will blink two colors:
•
Frequencies,
•
Orange to signal '0' and,
•
Codes (CTCSS/DPL) and,
•
Red for other values from '1' to '9'.
•
Auto-Scan.
The Programming Frequencies feature allows
you to select frequencies for each channel.
English
The Interference Eliminator Code (CTCSS/
DPL) helps minimize interference by providing
you with a choice of code combinations that
filter out static, noise, and unwanted
messages.
36
Short and long red blinks differentiate the
specific number the radio is signaling you.
Please refer to “Programming Mode: Reading
the Values” table on page 38.
PROGRAMMING MODE
Frequencies
First
Digit
PTT
Idle
Programming
Mode
Exit
Figure 1:
PTT
First
Digit
PTT
Long
PTT
Second
Digit
PTT
Third
Digit
PROGRAMMING
FEATURES
(PTT + SB1 + Turn ON radio)
Second
Digit
Long
PTT
PTT
Enter Programming Mode
CTCSS/DPL
PTT
PTT
“Roll Over”
key chirp
Auto- Scan
ON /
OFF
Long
PTT
Entering Programming Mode
37
English
Programming Mode: Reading the Values
Number
PROGRAMMING
FEATURES
English
38
Confirmation Beep
Zero beep
LED Indication
One orange blink
One beep
One short red blink
Two beeps
Two short red blinks
Three beeps
Three short red blinks
Four beeps
Four short red blinks
Long beep
One long red blink
Long beep and one beep
One long and one short red blinks
Long beep and two beeps
One long and two short red blinks
Long beep and three beeps
One long and three short red blinks
Long beep and four beeps
One long and four short red blinks
Entering Programming Mode
Note:
Before programming the features, make
sure your radio is set to the channel you
wish to program. You can do so before
entering Programming Mode or at any time
during the Programming Mode by turning
the Channel Selector Knob to the desired
channel
Note:
Reading Frequencies Values
When reading frequencies values you need to
read two digits as RDX Series™ radios have
27 frequencies for VHF and 89 frequencies for
UHF.
Once in ‘Idle’ Programming Mode, the radio will
signal the first value it was programmed when
you short press the PTT button (see Figure 2:
Reading Frequencies Values on page 40). This
value corresponds to the frequency's first digit
PROGRAMMING
FEATURES
To read or modify Frequencies, Codes and
Auto-Scan, set the radio to 'Programming
Mode' by long pressing both the PTT and the
SB1 button simultaneously while turning ON
the radio for 3 to 5 seconds until a ‘chirp’
sounds to indicate that you have entered 'Idle'
Programming Mode (*).The LED Indicator will
start blinking a green heartbeat.
Once you are in the 'Idle' Programming Mode,
you will be able to read the Frequencies,
Codes and Auto-Scan setting by short pressing
the PTT button to move along the different
programmable features.
(*)'Idle' Programming Mode is the stage of
the Programming Mode in which the radio is
waiting for the user to start the radio
programming cycle (refer “Entering
Programming Mode” on page 37)
39
English
value. If you short press the PTT button again,
the radio will signal you the second digit value.
PROGRAMMING M
Frequencies
PROGRAMMING
FEATURES
First
Digit
PTT
PTT
CTCSS
Second
Digit
Long
PTT
Idle
Programming
Mode
Figure 2:
PTT
The following is an example of the order in
which your radio will be signaling the ‘118’
CTCSS/DPL code:
First
Digit
Long
PTT
PTT
Reading Frequencies Values
Figure 3:
Reading CTCSS/DPL Values
If you continue short pressing the PTT button
as shown in Figure 1: Entering Programming
Mode on page 37 (stage 2), the radio will move
forward to programming CTCSS/PL Codes.
When reading the values for CTCSS/PL Codes
the radio signals you the digit codes each time
you short press the PTT button.
English
You will have to read three digits as RDX
Series™ have up to 122 codes available (refer
to “Frequencies and Codes Charts” Section).
40
•
Example of How to Program Values
Short press the PTT button. The radio will signal
you the first digit ‘1’.
•
Short press PTT button again and the radio will
show the second digit ‘1’ and,
•
Finally, short press PTT again and radio will show
the third digit ‘8’.
Reading Auto-Scan Values
After reading the CTCSS/DPL codes, short
press the PTT button and the radio will take
you to Auto-Scan (refer to Stage 3 of Figure 3:
Entering Programming Mode on page 40).
Auto-Scan only has two values:
It means AutoScan is...
OFF
ON
•
Note:
Auto-Scan is set to OFF by default.
While in Auto-Scan Mode, if you short press
PTT button, the radio will return to the ‘Idle’
Programming Mode. It will then generate a
‘roll-over’ chirp and it will start blinking a
green heartbeat
Each time your radio signals and beeps the
current setting you can change this setting by
either increasing it by short pressing SB1 or
decreasing it by short pressing SB2 . The
radio will then signal the new setting it has
been programmed.
Saving Settings
If you are satisfied with the setting, you can
either:
•
short press PTT to continue programming,
•
long press PTT to save and return to 'Idle'
•
long press the PTT button twice to exit 'Idle'
Programming Mode, or
PROGRAMMING
FEATURES
If the radio signals
the value...
Programming Frequencies, Codes and
Auto-Scan
Programming Mode and return to the normal
radio operation.
Note:
•
If you do not wish to save the value you just
programmed, turn radio OFF or change channel
using the channel knob.
41
English
•
If you ‘roll-over’ to the beginning at Idle
2.
code) value but the radio would not do it.
LED Indicator will start blinking green again. All
It rolled over and took me back to value
values that were changed will be automatically
‘0’.
saved.
Programming Mode FAQ
PROGRAMMING
FEATURES
1.
I got distracted while programming and
forgot which digit I was programming.
What should I do?
Return to 'Idle' Programming Mode and start
over, as you will not be able to return to the
Programming Mode (the radio does not provide
further way to let you know the specific stage
you are at when programming). Therefore you
can:
•
Long press the PTT button. The radio will return
to the 'Idle' Programming Mode or,
•
Turn OFF the radio and enter Programming
Mode again (see instructions in the beginning of
this section)
English
I am trying to program a frequency (or
Programming Mode you will hear a ‘chirp’ and the
42
The radio will not allow you to program any
values that are not available in the frequencies
and codes pool. For example, if you try to
program code 128, the radio would not accept
it, as the maximum value allowed is 122. Same
thing will happen with frequencies. Check the
Frequencies and Codes Charts section to
make sure you are programming a valid
number.
3.
I am trying to enter the Programming
Mode but the radio would not do it.
The radio might be locked using the CPS to not
allow Front Panel Programming. To re-enable,
use the CPS.
4.
When I was programming I made a
this channel and want to program another
channel.
If you make a mistake while programming a
value you have two choices:
The radio roll-over (and generates a 'wrap(9) or minimum (0) value. Keep increasing (short
press SB1) or decreasing (short pressing SB2)
until you get the desired value or,
5.
Turn OFF the radio and start-over.
I just programmed the value I wanted.
How do I exit Programming Mode?
•
If you are in Programming Mode you can exit by
long pressing the PTT button twice.
•
If you are already in the ‘Idle’ Programming
Mode, long press the PTT button once.
Switch to the new channel you wish to program
by using the Channel Selector Knob. The radio
will enter 'Idle' Programming Mode. If you wish
to save the changes, make sure you are in the
‘Idle’ Programming Mode before switching the
channel as otherwise you will lose the changes
made.
PROGRAMMING VALUES EXAMPLE
Example of Programming a Frequency
Assuming current frequency value is set to
Channel 1, with the UHF default frequency ‘02’
(equivalent to 464.5500 MHz), and you want to
change it to Frequency Number = ‘13’ (which is
mapped to 461.1375 MHz), follow this
sequence:
•
PROGRAMMING
FEATURES
around' sound) each time it reaches a maximum
•
I am done programming the features in
value. How can I erase it or re-program
it?
•
6.
mistake and programmed the wrong
Enter Programming Mode
43
English
•
Short press the PTT button to enter Frequency
Example of Programming a Code
Mode. Radio will signal current value ‘0’ (orange
•
Press the SB1 button once to increase first digit
to ‘1’.
Assuming current code value is set to factory
default ‘001’, and you want to change it to
CTCSS/DPL Code = 103 follow the sequence
below:
•
Short press the PTT button once to move ahead
•
Enter Programming Mode
•
Short press the PTT button three times (Enter
blink)
and program the frequency’s second digit. Radio
PROGRAMMING
FEATURES
will signal current value which is ‘2’ (two red
English
CTCSS/DPL Programming Selection Mode). The
blinks).
•
to ‘3’.
•
•
LED Indicator will blink orange to indicate that
Press the SB1 button to increase the digit value
current value is ‘0’
•
Press the SB1 button once (to change first digit to
Long press the PTT button. LED Indicator will
‘1’) LED Indicator will blink red. Short press the
show a green heartbeat to indicate 'Idle' state.
PTT button (to move forward and program
Long press the PTT button to exit Programming
second digit). The LED Indicator will blink orange
Mode or turn radio OFF.
to indicate current value is ‘0’.
44
•
Short press the PTT button and move ahead to
Example of Programming Auto-Scan
program the third digit. LED Indicator will blink
Auto-Scan is the last Programming Mode and
can be set to either ON or OFF on a particular
channel.
red to indicate current value is ‘1’.
•
Press the SB1 button to change the ‘third digit’ to
‘2’. Press the SB1 button to change again this
‘third digit’ to ‘3’. Radio will signal the chosen
value.
•
To set Auto-Scan to ON:
•
channel (see Figure 1: Entering Programming
Long press the PTT button to save changes and
Once in 'Idle' Programming Mode, LED Indicator
•
Auto-Scan Programming Selection Mode. The
will start blinking a green heartbeat.
•
Short press the PTT button six times to enter
radio will signal beeps and will show the current
Long press the PTT button to exit Programming
Auto-Scan setting (please refer to “Reading Auto-
Mode.
scan Settings” on page 41).
•
Short press the SB1 button to toggle ON/OFF the
PROGRAMMING
FEATURES
Mode on page 37).
return to 'Idle' Programming Mode.
•
Enter Programming Mode and select the desired
Auto-Scan feature in the channel. When ON, the
LED Indicator will blink RED once. When OFF,
the LED Indicator will blink ORANGE once.
45
English
PROGRAMMING
FEATURES
OTHER PROGRAMMING FEATURES
which was selected before Scan was activated. If
Scan
no transmission occurs within five seconds,
Scan allows you to monitor other channels to
detect conversations. When the radio detects a
transmission, it will stop scanning and will stop
on the active channel. This will allow you to
listen and talk to people on that channel without
having to change the channel knob. If there is
talking on Channel 2 during this time, the radio
will stay on Channel 1 and you will not hear
Channel 2. After talking has stopped in
Channel 1, the radio waits for 5 seconds before
resuming scan again.
•
To start scanning, press the SB2 button (*). When
the radio detects channel activity, it will stops on
that channel until the activity ends. You can talk
to the person(s) transmitting without having to
switch channels by pressing PTT.
•
To stop scanning, short press the SB2 button
•
By pressing the PTT button while the radio is
again.
scanning, the radio will transmit on the channel
English
46
scanning will resume.
•
If you want to scan a channel without Interference
Eliminator Codes (CTCSS/DPL), set the code
settings for the channels to ‘0’ in the CTCSS/DPL
Programming Selection Mode.
Whenever the radio is set up in Scan, the LED
Indicator will signal a red blink.
Note:
(*)Assumes the SB2 button is not
programmed to other function different from
the default. If Auto-Scan has been enabled
for a particular channel, do not press SB2 to
scan the channel, as the radio will do it
automatically.
Editing Scan List
To delete a channel from the Scan List:
Scan Lists can be edited by using the CPS
(refer to CPS section on page 48)
•
Start Scan by short pressing the SB2 button (*)
•
Wait until the radio stops on the channel you wish
to eliminate, then long press the SB2 button to
Nuisance Channel Delete
delete it.
•
The channel will not be removed until you exit
Scan by short pressing the SB2 button again or
by turning the radio OFF.
Note:
(*) Assumes the SB2 button is not
programmed to another function different
from the default.
47
PROGRAMMING
FEATURES
Nuisance Channel Delete allows you to
temporarily remove channels from the Scan
List. This feature is useful when irrelevant
conversations on a ‘nuisance’ channel tie up
the radio's scanning feature.
English
CPS (COMPUTER PROGRAMMING
SOFTWARE)
Radio to be
programmed
oftware
PROGRAMMING
FEATURES
CPS S
USB
Connector
Drop-in
Charger
Tray
Mini
Connector
CPS
Programming
Cable
The easiest way to program or change features
in your radio is by using the Computer
Programming Software (CPS) and the CPS
Programming Cable(*). CPS Software is
available for free as web based downloadable
software at:
www.motorola.com/RDX
English
48
To program, connect the RDX Series™ radio
via the Drop-in Charger Tray and CPS
Programming Cable as shown in the picture
above.
CPS allows the user to program frequencies,
PL/DPL codes, as well as other features such
as: Bandwidth Select, Time-out Timer, Power
Select, Battery Type Select, Scan List, Call
Tones, Scramble, Reverse Burst, etc. CPS is a
very useful tool as it can also lock the FrontPanel Radio Programming or restrict any
specific radio feature to be changed (to avoid
accidentally erasing the preset radio values). It
also provides security by giving the option to
set up a password for profile radio's
management. Please refer to Features
Summary Chart Section at the end of the user
guide for more details.
Note:
(*) CPS Programming
Cable (P/N RKN4155)
is an accessory sold separately. Please
contact your Motorola point of purchase for
more information.
Bandwidth Select
Default setting for Bandwidth Select depends
on the specific frequency and channel. Some
frequencies have selectable channel spacing,
which must match with other radios for
optimum audio quality.
For details, refer to Frequency and Code
Charts section.
When pressing the PTT button, transmissions
can be terminated by setting up a 'time-out’
timer.
Some frequencies may have FCC transmit
power restrictions that do not allow them to
be set at a higher power level. For details
see the Frequencies and Code Chart
Section.
Battery Type Setting
The RDX Series™ radio can be powered by
either Alkaline or Lithium-Ion batteries.
Call Tones
Call Tones feature allows you to transmit to
other radios in your group by alerting them that
you are about to talk or alerting them without
speaking.
Power Select
Power Select allows you to select between
high and low transmission power per frequency
in each channel. The power levels for RDX
Series™ 2W toggle between 1W and 2W or
2W and 4W/5W depends on the model.
49
PROGRAMMING
FEATURES
Time-Out Timer
Note:
English
Scramble L
Notes:
The Scramble feature makes transmissions
sound garbled to anyone listening without the
same code. Scramble default value is OFF.
•
PROGRAMMING
FEATURES
Reverse Burst
English
Reverse Burst eliminates unwanted noise
(squelch tail) during loss of carrier detection.
You can select values of either 180/240.
50
The features described in previous pages are just
some of the features CPS has. CPS offers more
capabilities. For more information refer to the
HELP file in the CPS.
•
Some of the features available with the CPS
software may vary depending on the radio model.
CLONING RADIOS
You can clone RDX Series™ radio profiles from
one Source radio to a Target radio by using any
one of these 3 methods:
or copied from) and
•
a Target radio (the radio which profile will be
cloned from the source radio.)
a Multi Unit Charger (optional accessory),
•
Two Single Unit Chargers (SUC) and a Radio-toRadio cloning cable (optional accessory),
The Source radio has to be in Pocket 1, 3 or 5
while the Target radio has to be in Pocket 2, 4
or 6, matching in the MUCs pockets by pairs as
follows:
•
the CPS (free software download)
•
1 and 2 or,
•
3 and 4 or,
•
5 and 6 (*).
Cloning with a Multi Unit Charger (MUC)
When cloning, the MUC does not need to be
plugged into a power source, but ALL radios
require charged batteries.
1.
Turn ON the Target radio and place it into one of
2.
Power the Source radio following the sequence
PROGRAMMING
FEATURES
•
the MUC Target Pockets
below:
To clone radios using the MUC, there must be
at least two radios:
•
a Source radio (radio which profiles will be cloned
• Long press the PTT button and SB2
simultaneously while turning the radio
ON.
51
English
• Wait for 3 seconds before releasing the
buttons until a distinctive audible tone is
heard.
3.
Place the Source radio in the source pocket that
pairs with the target pocket you chose in step 1.
Press and release SB1.
4.
After cloning is completed, the Source radio will
PROGRAMMING
FEATURES
sound either a ‘pass’ tone (cloning was
When ordering the MUC, please refer to P/N
RLN6309.
Notes:
•
run successfully.
failed). The ‘pass’ tone sounds like a good key
‘chirp’ whereas the ‘fail’ tone sounds similar to a
‘bonk’ tone. If the Source radio is a display
model, it will either show ‘Pass’ or ‘Fail’ on the
display (a tone will be heard within 5 seconds).
Once you have completed the cloning process,
turn the radios OFF and ON to exit the ‘cloning’
mode.
•
If cloning fails please refer to “What To Do if
Cloning Fails” on page 54.
52
Paired Target radios and Source radios must be
of the same band type in order for the cloning to
successful) or a ‘fail’ tone (cloning process has
5.
English
Further details on how to clone radios are
explained in the Instructions Sheet provided
with the MUC.
•
(*) MUC pockets numbers should be read from
left to right with the Motorola logo facing front.
Cloning Radio using the Radio to Radio
(R2R) Cloning Cable (Optional Accessory)
2.
Unplug any cables (power supply or USB
cables) from the SUCs.
3.
Plug one side of the cloning cable mini
connector to one SUC. Plug the other end to
the second SUC.
Note:
4.
Turn ON the Target radio and place it into one of
5.
On the Source radio, power the radio following
the SUCs.
the sequence below:
Operating Instructions
1.
• Long press the PTT button and SB2
Before beginning the cloning process, make
simultaneously while turning the radio
sure you have:
ON.
• A fully charged battery on each one of
• Wait for 3 seconds before releasing the
the radios.
buttons until a distinctive audible tone is
• Two Single Unit Chargers (SUC).
• Turned OFF the radios and,
• Both radios are of the same radio
PROGRAMMING
FEATURES
During the cloning process no power is
being applied to the SUC. The batteries will
not be charged. A data communication is
being established between the two radios.
heard.
6.
Place the Source radio in its SUC, press and
release SB1.
model.
53
English
7.
After cloning is completed, the Source radio will
3.
sound either a ‘pass’ tone (cloning was
successful) or a ‘fail’ tone (cloning process has
to the radio.
4.
failed). The ‘pass’ tone sounds like a good key
‘chirp’ whereas the ‘fail’ tone sounds similar to a
‘bonk’ tone. If the Source radio is a display
model, it will either show ‘Pass’ or ‘Fail’ on the
PROGRAMMING
FEATURES
display (a tone will be heard within 5 seconds).
8.
Ensure that the Source radio is in cloning mode.
6.
Ensure that the Target radio is turned ON.
7.
Ensure that radios are both from the same type
(same frequency band, same front panel
(display/non display), same region and same
transmission power).
mode.
Note:
1.
Ensure that the batteries on both radios are fully
2.
Check the cloning cable connection on both
charged.
SUCs.
English
5.
turn the radios OFF and ON to exit ‘clone’
The radio will emit an audible ‘bonk’ indicating
that the cloning process has failed. In the event
that cloning fails, try performing each of the
following before trying to start the cloning
process again:
54
Ensure that there is no debris in the charging
tray or on the radio contacts.
Once you have completed the cloning process,
What To Do if Cloning Fails
Ensure that the battery is engaged properly on
This cloning cable is designed to operate
only with compatible Motorola RLN6175
(Standard) and RLN6304 (Rapid) Single
Unit Chargers.
When ordering Cloning Cable please refer to P/
N RLN6303. For details about accessories
refer to Accessories section.
Cloning using the CPS (Computer
Programming Software)
Information on how to clone using the CPS is
available either in:
When cloning using this method, you will need
to have the CPS software, a Drop-in Tray
Charger and the CPS Programming Cable.
•
the CPS Help File --> Content and Index -->
•
in the CPS Programming Cable Accessory
To order the CPS Programming Cable, please
refer to P/N RKN4155.
Cloning Radios, or
Leaflet.
PROGRAMMING
FEATURES
55
English
TROUBLESHOOTING
Symptom
Try This...
Recharge or replace the Li-Ion battery.
No Power
Reposition or replace AA batteries.
Extreme operating temperatures may affect battery life.
Refer to See “About the Li-Ion Battery” on page 14.
Confirm Interference Eliminator Code is set.
Hearing other noises or
conversation on a channel
Frequency or Interference Eliminator Code may be in use.
Change settings: either change frequencies or codes on all radios.
Make sure radio is at the right frequency and code when transmitting.
TROUBLESHOOTING
Refer to “Talking and Monitoring” on page 29
English
Message Scrambled
Audio quality not good enough
56
Scramble Code might be ON, and/or setting does not match the other radios'
settings.
Radio settings might not be matching up correctly. Double check frequencies,
codes and bandwidths to make sure they are identical in all radios
Symptom
Try This...
Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease
range. Check for clear line of sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt decreases range.
Change location of radio. To increase range and coverage, you can either
Limited talk range
reduce obstructions, increase power, or use UHF radio instead of VHF radio.
UHF radios provide greater coverage in industrial and commercial buildings.
VHF is designed for outdoor or smaller or wood structures. Increasing power
provides greater signal range and increased penetration through obstructions.
Refer to See “Talking and Monitoring” on page 29.
Make sure the PTT button is completely pressed when transmitting.
Confirm that the radios have the same Channel, Frequency, Interference
Eliminator Code and Scramble Code settings. Refer to “Talking and Monitoring”
section on page 29 for further information.
Recharge, replace and/or reposition batteries. Refer to “About your Li-Ion
received
Battery” section on page 14.
Obstructions and operating indoors, or in vehicles, may interfere. Change
location. Refer to “Talking and Monitoring” Section on page 29.
Verify that the radio is not in Scan. Refer to “Scan” on page 46 and “Nuisance
Channel Delete” on page 47.
57
TROUBLESHOOTING
Message not transmitted or
English
Symptom
Try This...
Radios are too close; they must be at least five feet apart.
Heavy static or interference
Radios are too far apart or obstacles are interfering with transmission.
Refer to “Talking and Monitoring” on page 29.
Recharge or replace Li-Ion battery. Replace AA batteries.
Low batteries
Extreme operating temperatures affect battery life.
Refer to “About the Li-Ion Battery” on page 14.
Check that the radio/battery is properly inserted and check the battery/charger
Drop-in Charger LED light
does not blink
contacts to ensure that they are clean and charging pin is inserted correctly.
Refer to “Charging the Battery” section on page 22, “Drop-in Tray Charger LED
Indicators” section on page 25 and “Installing the Lithium-Ion Battery” section
TROUBLESHOOTING
on page 16.
English
Low battery indicator is
blinking although new
batteries are inserted
58
Verify that the radio is set to the correct battery type.
Refer to “Installing the Li-Ion Battery” section on page 16, “Installing Alkaline
Batteries” section on page 17 and “About your Li-Ion Battery” section on
page 14.
Symptom
Try This...
VOX feature might be set to OFF.
Cannot activate VOX
Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’.
Accessory not working or not compatible.
Refer to “Hands-Free Use/VOX” section on page 33.
Check drop-in tray charger is properly connected and correspond to a
compatible power supply.
Battery does not charge
although it has been placed in
the drop-in charger for a while
Ensure that you have the drop-in tray charger adjustable piece placed on the
right position.
Refer to “Charging with the Drop-In Tray Single Unit Charger” section on
page 22 and “Charging a Standalone Battery” section on page 23.
Check the charger’s LEDs indicators to see if the battery has a problem. Refer
to “Drop-in Tray Charger LED Indicators” section on page 25.
Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check
to see if the radio has been programmed using the CPS with a customized profile.
59
TROUBLESHOOTING
Note:
English
USE AND CARE
USE AND CARE
Use a soft damp cloth
to clean the exterior
Do not immerse
in water
Do not use alcohol or
cleaning solutions
If the radio is submerged in water...
Turn radio OFF and
remove batteries
English
60
Dry with soft cloth
Do not use radio until
completely dry
FREQUENCY AND CODE CHARTS
RDX VHF FREQUENCIES CHART
The charts in this section provide Frequency and Code information. These charts are useful when
using Motorola RDX Series™ two-way radios with other business radios. Most of the frequency’s
positions are the same as Spirit M, GT, S, and XTN Series Frequencies.
Frequency #
Frequency
Bandwidth
(MHz)
Frequency #
Frequency
(MHz)
Bandwidth
151.6250
25.0 kHz
11
151.6550
25.0 kHz
151.9550
25.0 kHz
12
151.6850
25.0 kHz
152.8850
25.0 kHz
13
151.7150
25.0 kHz
152.9150
25.0 kHz
14
151.7450
25.0 kHz
151.7000
12.5 kHz
15
151.7750
25.0 kHz
151.7600
12.5 kHz
16
151.8650
25.0 kHz
*7
152.9450
12.5/25.0 kHz
17
151.8950
25.0 kHz
*8
151.8350
12.5/25.0 kHz
18
151.9250
25.0 kHz
*9
151.8050
12.5/25.0 kHz
19
152.7000
25.0 kHz
†10
151.5125
12.5 kHz
20
154.4900
25.0 kHz
61
FREQUENCY AND CODE
RDX VHF Frequencies
English
RDX VHF Frequencies (cont.)
FREQUENCY AND CODE
Frequency #
Frequency
Bandwidth
(MHz)
Frequency #
Frequency
(MHz)
Bandwidth
21
154.5150
25.0 kHz
25
154.6550
25.0 kHz
†22
154.5275
12.5 kHz
26
158.4000
25.0 kHz
23
154.5400
25.0 kHz
†
158.4075
12.5 kHz
24
153.0050
25.0 kHz
27
Notes:
•
(†) Bandwidth for frequencies 10, 22 and 27 are not selectable and different from XTN. You might
notice the communication quality differences when using these frequencies to interoperate with XTN
radios.
•
(*) Due to FCC regulations these frequencies (six in total) are different from the previous Motorola
Legacy Series radios. This means that if you select the RDX radio in one of these frequencies the
radio will not inter-operate with an XTN radio. In order for a RDX radio to inter-operate with an XTN
radio, make sure you choose any of the frequencies (21 in total) that are common for both radios.
English
62
RDV2020 - VHF DEFAULT FREQUENCIES CHART
The following are the default frequencies programmed in your RDX Radio. Note that the VHF default
frequencies programmed in channels 1 and 2 are different from the XTN Series default values. In
order for a RDX radio to inter-operate with an XTN radio, you must make sure you choose any of the
frequencies (21 in total, read User Guide for details) that are common for both radios.
Channel
Frequency #
Frequency
(MHz)
Code #
Code
Bandwidth
20
154.4900
67.0 Hz
25.0 kHz
21
154.5150
67.0 Hz
25.0 kHz
Note:
For RDV2020, refer to Channel # 1 and # 2.
63
FREQUENCY AND CODE
BRUS RDX VHF 2CH Radios Default Frequencies - RDV2020
English
MAKING XTN COMPATIBLE WITH RDX RADIOS - QUICK INSTRUCTIONS
The following instructions are a quick and easy way to make your XTN (XV1100, XV2100 and
XV2600 models) compatible with RDX Series™ default frequencies:
1.
Make sure your XTN is programmed to the factory default frequencies (Turn your radio ON while holding the
2.
Program Channel 1 with Frequency # 20 (154.4900 Mhz) and Channel 2 (for models XV2100 and XV2600
FREQUENCY AND CODE
MENU and PTT buttons simultaneously for three seconds).
only) with Frequency # 21 (154.5150 Mhz).
XTN VHF Default Frequencies
•
Channel
Frequency #
Frequency
(Mhz)
Code
Bandwidth
**3
154.5700
67.0 Hz
25.0 kHz
**4
154.6000
67.0 Hz
25.0 kHz
151.6250
67.0 Hz
25.0 kHz
151.9550
67.0 Hz
25.0 kHz
10
151.5125
67.0 Hz
25.0 kHz
12
151.6850
67.0 Hz
25.0 kHz
Due to FCC regulations, the highlighted frequencies are different from the XTN default
values. Make sure to choose a compatible frequency whenever you need to
interoperate with XTN series.
•
(**) Former XTN frequencies # 3 (154.5700 MHz) and # 4 (154.6000 MHz) are
considered MURS frequencies and are not available in the RDX Series™.
English
64
RDV5100 - VHF DEFAULT FREQUENCIES CHART
Default frequencies for the RDV5100 are fully compatible with the AXV5100 radios (AX Series). If
you need to make this radio compatible with XTN series, please re-program RDV5100 frequencies
to match XTN frequencies defaults.
RDX VHF 10CH Radios Default Frequencies - RDV5100
Frequency #
Frequency
(MHz)
Code #
Code
Bandwidth
151.6250
67.0 Hz
25.0 kHz
Note:
151.6250
77.0 Hz
25.0 kHz
151.6250
88.5 Hz
25.0 kHz
151.6250
29
179.9 Hz
25.0 kHz
151.6250
25.0 kHz
151.9550
67.0 Hz
25.0 kHz
151.9550
82.5 Hz
25.0 kHz
151.9550
10
94.8 Hz
25.0 kHz
151.9550
29
179.9 Hz
25.0 kHz
10
151.9550
25.0 kHz
FREQUENCY AND CODE
Channel
Compatible with AXV5100 radios (AX series)
65
English
RDX UHF FREQUENCIES CHART
RDX UHF Frequencies (cont.)
Frequency
(MHz)
*3
FREQUENCY AND CODE
Frequency #
English
Bandwidth
Frequency #
Frequency
(MHz)
Bandwidth
464.5000
12.5/25.0 kHz
14
461.1625
12.5 kHz
464.5500
12.5/25.0 kHz
15
461.1875
12.5 kHz
467.7625
12.5 kHz
16
461.2125
12.5 kHz
*4
467.8125
12.5 kHz
17
461.2375
12.5 kHz
*5
467.8500
12.5/25.0 kHz
18
461.2625
12.5 kHz
*6
467.8750
12.5/25.0 kHz
19
461.2875
12.5 kHz
*7
467.9000
12.5/25.0 kHz
20
461.3125
12.5 kHz
*8
467.9250
12.5/25.0 kHz
21
461.3375
12.5 kHz
461.0375
12.5 kHz
22
461.3625
12.5 kHz
10
461.0625
12.5 kHz
*23
462.7625
12.5 kHz
11
461.0875
12.5 kHz
*24
462.7875
12.5 kHz
12
461.1125
12.5 kHz
*25
462.8125
12.5 kHz
13
461.1375
12.5 kHz
*26
462.8375
12.5 kHz
66
RDX UHF Frequencies (cont.)
Bandwidth
Frequency #
Frequency
(MHz)
Bandwidth
*27
462.8625
12.5 kHz
38
466.1375
12.5 kHz
*28
462.8875
12.5 kHz
39
466.1625
12.5 kHz
*29
462.9125
12.5 kHz
40
466.1875
12.5 kHz
30
464.4875
12.5 kHz
41
466.2125
12.5 kHz
31
464.5125
12.5 kHz
42
466.2375
12.5 kHz
32
464.5375
12.5 kHz
43
466.2625
12.5 kHz
33
464.5625
12.5 kHz
44
466.2875
12.5 kHz
34
466.0375
12.5 kHz
45
466.3125
12.5 kHz
35
466.0625
12.5 kHz
46
466.3375
12.5 kHz
36
466.0875
12.5 kHz
47
466.3625
12.5 kHz
37
466.1125
12.5 kHz
*48
467.7875
12.5 kHz
67
FREQUENCY AND CODE
Frequency #
Frequency
(MHz)
English
FREQUENCY AND CODE
RDX UHF Frequencies (cont.)
English
Frequency #
Frequency
(MHz)
Bandwidth
Frequency #
Frequency
(MHz)
Bandwidth
*49
467.8375
12.5 kHz
61
467.1875
12.5 kHz
*50
467.8625
12.5 kHz
62
467.4625
12.5 kHz
*51
467.8875
12.5 kHz
63
467.4875
12.5 kHz
*52
467.9125
12.5 kHz
64
467.5125
12.5 kHz
53
469.4875
12.5 kHz
65
451.1875
12.5 kHz
54
469.5125
12.5 kHz
66
451.2375
12.5 kHz
55
469.5375
12.5 kHz
67
451.2875
12.5 kHz
56
469.5625
12.5 kHz
68
451.3375
12.5 kHz
57
462.1875
12.5 kHz
69
451.4375
12.5 kHz
58
462.4625
12.5 kHz
70
451.5375
12.5 kHz
59
462.4875
12.5 kHz
71
451.6375
12.5 kHz
60
462.5125
12.5 kHz
72
452.3125
12.5 kHz
68
RDX UHF Frequencies (cont.)
Bandwidth
Frequency #
Frequency
(MHz)
Bandwidth
73
452.5375
12.5 kHz
82
456.4375
12.5 kHz
74
452.4125
12.5 kHz
83
456.5375
12.5 kHz
75
452.5125
12.5 kHz
84
456.6375
12.5 kHz
76
452.7625
12.5 kHz
85
457.3125
12.5 kHz
77
452.8625
12.5 kHz
86
457.4125
12.5 kHz
78
456.1875
12.5 kHz
87
457.5125
12.5 kHz
79
456.2375
12.5 kHz
88
457.7625
12.5 kHz
80
456.2875
12.5 kHz
89
457.8625
12.5 kHz
81
456.3375
12.5 kHz
Notes:
•
(*) Frequency limited to 2W maximum power output
•
When referring to XTN radios, note that frequencies from # 57 to # 89 are 33 new additional frequencies
69
FREQUENCY AND CODE
Frequency #
Frequency
(MHz)
English
RDU2020 - UHF DEFAULT FREQUENCIES CHART
FREQUENCY AND CODE
RDX UHF 2CH Radios Default Frequencies - RDU2020
English
Channel
Frequency #
Frequency
(MHz)
Code #
Code
Bandwidth
464.5500
67.0 Hz
25.0 kHz
467.9250
67.0 Hz
25.0 kHz
Note:
70
Compatible with XTN series radios
RDU4100 - UHF DEFAULT FREQUENCIES CHART
Default frequencies for the RDU4100 are fully compatible with the AXU4100 radios (AX Series). If
you need to make this radio compatible with XTN series, please re-program RDU4100 frequencies
to match XTN UHF frequencies defaults.
RDX UHF 10 CH Radios Default Frequencies - RDU4100
Frequency #
Frequency
(MHz)
Code #
Code
Bandwidth
464.5000
67.0 Hz
25.0 kHz
464.5000
77.0 Hz
25.0 kHz
464.5000
88.5 Hz
25.0 kHz
Note:
464.5000
29
179.9 Hz
25.0 kHz
464.5000
25.0 kHz
464.5500
67.0 Hz
25.0 kHz
464.5500
82.5 Hz
25.0 kHz
464.5500
10
94.8 Hz
25.0 kHz
464.5500
29
179.9 Hz
25.0 kHz
10
464.5500
25.0 kHz
FREQUENCY AND CODE
Channel
Compatible with AXU4100 radios series (AX series)
71
English
CTCSS AND PL/DPL CODES
CTCSS Codes
Hz
CTCSS
Hz
CTCSS
Hz
67.0
14
107.2
27
167.9
71.9
15
110.9
28
173.8
179.9
FREQUENCY AND CODE
CTCSS
74.4
16
114.8
29
77.0
17
118.8
30
186.2
79.7
18
123
31
192.8
82.5
19
127.3
32
203.5
85.4
20
131.8
33
210.7
88.5
21
136.5
34
218.1
91.5
22
141.3
35
225.7
10
94.8
23
146.2
36
233.6
11
97.4
24
151.4
37
241.8
12
100.0
25
156.7
38
250.3
103.5
26
162.2
122 (*)
69.3
13
Note:
English
72
(*) New CTCSS code.
PL/DPL Codes (cont.)
DPL
Code
DPL
Code
DPL
Code
39
23
55
116
71
243
40
25
56
125
72
244
41
26
57
131
73
245
31
58
132
74
251
43
32
59
134
75
261
44
43
60
143
76
263
45
47
61
152
77
265
46
51
62
155
78
271
47
54
63
156
79
306
48
65
64
162
80
311
49
71
65
165
81
315
50
72
66
172
82
331
343
51
73
67
174
83
52
74
68
205
84
346
53
114
69
223
85
351
54
115
70
226
86
364
FREQUENCY AND CODE
42
73
English
FREQUENCY AND CODE
PL/DPL Codes (cont.)
English
74
DPL
Code
DPL
Code
DPL
Code
87
365
99
503
111
654
88
371
100
506
112
662
89
411
101
516
113
664
90
412
102
532
114
703
91
413
103
546
115
712
92
423
104
565
116
723
93
431
105
606
117
731
94
432
106
612
118
732
95
445
107
624
119
734
96
464
108
627
120
743
97
465
109
631
121
754
98
466
110
632
PROGRAMMING CUSTOMIZED FREQUENCIES ON 4W/5W RDX MODELS
Certain 4W/5W Models can be programmed to have customized frequencies (different from the
ones shown in the VHF and UHF charts in previous pages). VHF range is 146 -174 MHz and UHF
438 - 470 MHz.
Certain 4W/5W models can also be programmed to work with repeaters.
Please contact your Motorola point of purchase for details.
FREQUENCY AND CODE
75
English
MOTOROLA LIMITED
WARRANTY FOR THE
UNITED STATES AND
CANADA
WARRANTY
What Does this Warranty Cover?
English
Subject to the exclusions contained below,
Motorola, Inc. warrants its telephones, pagers, and
consumer and business two-way radios (excluding
commercial, government or industrial radios) that
operate via Family Radio Service or General
Mobile Radio Service, Motorola-branded or
certified accessories sold for use with these
Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media
and sold for use with these Products (“Software”)
to be free from defects in materials and
workmanship under normal consumer usage for
the period(s) outlined below.
This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola
Products, Accessories and Software purchased by
consumers in the United States, which are
accompanied by this written warranty.
76
Products and Accessories
Products Covered
Length of Coverage
Products and
Accessories as defined
above, unless otherwise
provided for below.
One (1) year from the date
of purchase by the first
consumer purchaser of the
product unless otherwise
provided for below.
Decorative
Accessories and
Cases.
Decorative covers,
bezels, PhoneWrap™
covers and cases.
Limited lifetime warranty
for the lifetime of ownership
by the first consumer
purchaser of the product.
Business Two-way
Radio Accessories
One (1) year from the date
of purchase by the first
consumer purchaser of the
product.
Products and
Accessories that are
Repaired or Replaced.
The balance of the original
warranty or for ninety (90)
days from the date returned
to the consumer, whichever
is longer.
Exclusions
Use of Non-Motorola Products and
Accessories. Defects or damage that result from
the use of Non-Motorola branded or certified
Products, Accessories, Software or other
peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects
or damages resulting from service, testing,
adjustment, installation, maintenance, alteration,
or modification in any way by someone other than
Motorola, or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with
(a) serial numbers or date tags that have been
removed, altered or obliterated; (b) broken seals
or that show evidence of tampering; (c)
mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or
parts, are excluded form coverage.
WARRANTY
Normal Wear and Tear. Periodic maintenance,
repair and replacement of parts due to normal
wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged
capacity falls below 80% of their rated capacity
and batteries that leak are covered by this limited
warranty.
Abuse & Misuse. Defects or damage that result
from: (a) improper operation, storage, misuse or
abuse, accident or neglect, such as physical
damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with
liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (d)
other acts which are not the fault of Motorola, are
excluded from coverage.
77
English
Communication Services. Defects, damages, or
the failure of Products, Accessories or Software
due to any communication service or signal you
may subscribe to or use with the Products
Accessories or Software is excluded from
coverage.
Software. Applies only
to physical defects in
the media that
embodies the copy of
the software (e.g. CDROM, or floppy disk).
Length of Coverage
Ninety (90) days from the
date of purchase.
WARRANTY
Software Embodied in Physical Media. No
warranty is made that the software will meet your
requirements or will work in combination with any
hardware or software applications provided by
third parties, that the operation of the software
products will be uninterrupted or error free, or that
all defects in the software products will be
corrected.
78
HOW TO OBTAIN WARRANTY SERVICE OR
OTHER INFORMATION?
Contact your Motorola point of purchase.
Exclusions
English
WHO IS COVERED?
This warranty extends only to the first consumer
purchaser, and is not transferable.
Software
Products Covered
Software NOT Embodied in Physical Media.
Software that is not embodied in physical media
(e.g. software that is downloaded from the
internet), is provided “as is” and without warranty.
SOFTWARE COPYRIGHT NOTICE
The Motorola products described in this manual
may include copyrighted Motorola and third party
software stored in semiconductor memories or
other media. Laws in the United States and other
countries preserve for Motorola and third party
software providers certain exclusive rights for
copyrighted software, such as the exclusive rights
to distribute or reproduce the copyrighted
software. Accordingly, any copyrighted software
contained in the Motorola products may not be
modified, reverse-engineered, distributed, or
reproduced in any manner to the extent allowed by
law.
Furthermore, the purchase of the Motorola
products shall not be deemed to grant either
directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or
patent applications of Motorola or any third party
software provider, except for the normal, nonexclusive, royalty-free license to use that arises by
operation of law in the sale of a product.
EXPORT LAW ASSURANCES
This product is controlled under the export
regulations of the United States of America. The
Governments of the United States of America may
restrict the exportation or re-exportation of this
product to certain destinations. For further
information contact the U.S. Department of
Commerce.
PATENT NOTICE
This product is covered by one or more of the
following United States patents.
5896277 5894292 5864752 5699006 5742484
D408396 D399821 D387758 D389158 5894592
5893027 5789098 5734975 5861850 D395882
D383745 D389827 D389139 5929825 5926514
5953640 6071640 D413022 D416252 D416893
D433001
WARRANTY
79
English
ACCESSORIES
ACCESSORIES
ANTENNAS
Part No.
Description
RAN4033
UHF Stubby Antenna 450-470
MHz
RAN4041
VHF Helical Antenna 146-174
MHz
RAN4031
UHF Whip Antenna 438 - 470
MHz
AUDIO ACCESSORIES
Part No.
English
Description
53815
Headset w/Boom Mic BR
53862
Remote Speaker Mic BR
53863
Earpiece w/Mic BR
80
Part No.
Description
53865
Headset w/Swivel Boom Mic
53866
Earbud w/Clip PTT Mic BR
56517
Earpiece w/Inline Mic
56518
Earpiece w/Boom Mic
BATTERY
Part No.
Description
RLN6306
Alkaline Battery Frame
RLN6351
Standard Li-Ion Battery
RLN6305
High Capacity Li-Ion
Battery
RLN6308
Ultra High Capacity Li-Ion
Battery
CARRY ACCESSORIES
Description
Part No.
Description
RLN6302
Hard Leather Carry Case
RLN6303
Radio to Radio Cloning Cable
RLN6307
Spring Action Belt Clip
RKN4155
CPS Programming Cable
POWER SUPPLIES AC PIN ADAPTORS
Part No.
RLN6349
Description
North America AC Pin Adaptor
CHARGERS
Part No.
Part No.
RVN5147
Description
RLN6304
Rapid ACCY Charging Kit Americas (*)
RLN6309
Multi Unit Charger (MUC) Kit North America
RLN6175
Standard Drop-in Tray Charger
SOFTWARE APPLICATIONS
Description
ACCESSORIES
Part No.
CABLES
Computer Programming
Software (CPS)
81
English
ACCESSORIES
POWER SUPPLIES
English
RPN4054
Standard US Fixed Power
Supply
Attention: Certain accessories may be or may not be
available at the time of purchase. For latest
information on accessories, contact your Motorola
point of purchase or visit:
www.motorola.com/RDX or www.motorola.com/
radios/business
RPN4058
Standard Exchg AC pin Pwr
Supply
(*) Americas Rapid Charging Kit includes Power
Supply, Drop-in Tray Charger, and AC Pin adaptors.
RLN6170
Rapid Exchg AC pin Pwr Supply
Part No.
82
Description
M
RDX Series™ Features Summary
Programmable Via
RADIO PANEL
Programmable via
CPS
Features
Backlight
Default Value
Display
NonDisplay
Display
NonDisplay
No
N/A
Yes
N/A
5 Seconds
Programming Tips
Choose the backlight’s time out by using the CPS.
Front panel programming available only on display
Bandwidth
Select
Yes
No
Yes
Yes
Frequency
Dependable
models by entering Programming Mode (1).
Bandwidth is programmable according to FCC
frequency regulations. Refer to the Frequencies and
Code Charts Section for details.
Battery Save
(2)
Yes
Yes
Yes
Yes
ON
To enable/disable Battery Save, press SB1 and SB2
simultaneously while turning ON the radio.
Front panel radio programming is available in
display models by pressing the MENU button and
Battery Type
Yes
No
Yes
Yes
Li-Ion
scrolling down/up with
and
buttons to set
value. Long press PTT to save and exit.
Available only via CPS. Allows to reset the radio
Buttons Reset
No
No
Yes
Yes
ON
buttons to factory default values. Refer to Radio
Buttons Summary Table.
83
Programmable Via
RADIO PANEL
Features
Display
NonDisplay
Programmable via
CPS
Display
NonDisplay
Default Value
Programming Tips
Front panel radio programming available only for
Call Tones (4)
Yes
No
Yes
Yes
OFF /
BUTTON A
Display Models by going into Programming
Mode(1). Values available are 0 (OFF),1, 2 and 3.
To enable/disable Call Tones press Button A (default
button).
Only Display Models. To enter or exit Channel
Aliasing mode press PTT and
Channel
Aliasing
Yes
N/A
Yes
N/A
OFF
buttons
simultaneously while turning radio ON for 3 sec.
After editing, to exit and save, long press PTT.
Note: To edit, refer to Programming Features/
Editing Channels.
You can select channels using the Channel Selector
Knob (non-display models) or the MENU button
(display models). You can also add or delete
Channels
Yes
Yes
Yes
Yes
Model Dependant
channels by using the CPS.
Note: Enabling/disabling channels via CPS will
automatically affect the Max Channels you are able
to program via front panel.
84
Programmable Via
RADIO PANEL
Programmable via
CPS
Features
Default Value
Display
NonDisplay
Display
Programming Tips
NonDisplay
Enables radio to enter cloning mode in order to
clone its profile settings into other radios (using
Cloning Mode
Yes
Yes
Yes
Yes
OFF
Radio to Radio Cloning Cable or Multi-Unit
Charger). Press PTT, SB2 while turning radio ON.
Note: You can clone radios using the CPS.
This feature is referred in the CPS software as
“Codeplug Password”. It prevents unauthorized
CPS Manager
Lock
No
No
Yes
Yes
N/A
access to the CPS to the radio’s programmed
configuration. Make sure you set up a 4 digits
password that is easy to remember.
End of Tx
Tone (or
Roger Beep)
(2)
To enable/disable press SB1 while powering up the
Yes
Yes
Yes
Yes
OFF
radio
There are 27 VHF frequencies and 89 UHF
Frequencies
Yes
Yes
Yes
Yes
Channel and
Model Dependant
frequencies available. Use Programming Mode (1)
for front panel radio programming. Refer to
Frequencies and Codes Charts Section for details.
85
Programmable Via
RADIO PANEL
Features
Display
NonDisplay
Programmable via
CPS
Display
NonDisplay
Default Value
Any value within
Frequencies,
Direct Input
(3)
No
No
Yes
Yes
radio frequency
Programming Tips
Allows you to customize frequencies in your radio.
Available only for certain 4W/5W radio models.
band
Radios Bandwidth is fixed and non-programmable.
Bandwidth
Range
N/A
N/A
N/A
N/A
Model Dependant
Bandwidth Range for 2W radios: VHF 150.8 - 160
Mhz / UHF 450-470 Mhz Bandwidth Range for 4W/
5W radios: VHF: 146-174 Mhz / UHF 438-470 Mhz.
Use Programming Mode for front panel radio
Codes,
Interference
Eliminator
Codes
(CTCSS/DPL)
Yes
Yes
Yes
Yes
Channel and
Model Dependant
programming. There are 122 codes available.For
details refer to Frequencies and Codes Charts
Section.
Hands free without accessories, available for
IVOX, enable/
disable
Yes
N/A
N/A
N/A
OFF
display models only. To enable IVOX long press the
PTT button while turning radio ON and until the
IVOX icon blinks.
86
Programmable Via
RADIO PANEL
Programmable via
CPS
Features
Default Value
Display
NonDisplay
Display
NonDisplay
IVOX,
sensitivity
Level
Yes
N/A
Yes
N/A
Keypad Beep (
or Keypad
Tone) (2)
Yes
Yes
Yes
Yes
ON
Keypad Lock
(2)
Yes
N/A
Yes
N/A
UNLOCKED
LEDs Enabled/
Disabled
No
No
Yes
Yes
Enabled
Low Battery
Alert Shutdown
N/A
N/A
N/A
N/A
ON
HIGH
(Level 3)
Programming Tips
Available for Display models only. Allows user to
specify IVOX sensitivity level. For front panel radio
programming use the MENU button.
Press SB2 while turning ON radio to enable/disable
keypad beep.
Press and hold MENU for 4 seconds to lock the
radio keypad.To unlock, press MENU for 4 seconds.
Using CPS you can disable radio LEDs
Gives a sequence of loud and high beep tones to
alert battery level is low. LED will blink orange
several times. This a non-programmable feature.
87
Programmable Via
RADIO PANEL
Features
Display
NonDisplay
Programmable via
CPS
Display
NonDisplay
Default Value
Programming Tips
Front panel radio programming (only Display
Maximum
Channels (2)
Yes
No
Yes
Yes
Model and CPS
models): Set radio to Programming Mode(1) to get
programmable
the Maximum Channels Menu option.
dependant
Note: Default value is set to the maximum number
of channels that the radio supports.
Microphone
Gain Level,
ACCESSORY
Yes
No
Yes
Yes
Microphone
Gain Level,
RADIO
Yes
No
Yes
Yes
Medium
For front panel programming enter Programming
(Level 2)
Mode (1).
Medium
For front panel programming enter Programming
(Level 2)
Mode (1).
Long Press SB1 to monitor and press SB1 again to
Monitor (4)
Yes
Yes
Yes
Yes
SB1 Button
release.
Note: PL/DPL defeat feature should be disabled in
order to monitor.
88
Programmable Via
RADIO PANEL
Programmable via
CPS
Features
Default Value
Display
NonDisplay
Display
Programming Tips
NonDisplay
Press SB2 to start scanning and wait until the radio
lands on the channel you want to delete. Long press
Nuisance Ch
Delete (4)
Yes
Yes
Yes
Yes
SB2 Button
SB2 to delete the channel.
Note: The nuisance deleted channel will be restored
into the scan list when the radio is turned OFF or
you exit SCAN.
Also known as ‘Squelch defeat’. Short Press SB1 to
PL Defeat
Yes
Yes
Yes
Yes
SB1 Button
enable PL/DPL defeat so you can listen or monitor
any activity in the channel without noise. Press SB1
again to disable PL/DPL defeat.
Use CPS for selecting the transmission power level
High Power
Power Select
(4)
No
No
Yes
Yes
(Model
dependant)
you want for each channel. Power level default
depends on maximum power the radio supports.
Note: There may be power restrictions depending
on the frequency chosen in each channel.
89
Programmable Via
RADIO PANEL
Features
Programmable via
CPS
Display
NonDisplay
Display
NonDisplay
No
N/A
Yes
N/A
Default Value
Programming Tips
Text that shows up in the radio display when turned
Power up Text
MOTOROLA
ON. Default text is MOTOROLA. Programmable via
CPS.
Repeater/
Talkaround (3)
No
No
Yes
Yes
OFF
Reset to
Factory
Defaults (2)
Yes
Yes
Yes
Yes
Enabled
Reverse Burst
No
Available only for RDU4163d and RDU4160d radio
models.
Allows to restore radio's factory defaults. Press PTT,
SB1, SB2 simultaneously for 3 seconds while
turning ON radio.
Reverse Burst eliminates unwanted noise (squelch
No
Yes
Yes
180
tail) during loss of carrier detection. Use CPS to
select values 180 or 240.
90
Programmable Via
RADIO PANEL
Programmable via
CPS
Features
Scan
Default Value
Display
NonDisplay
Display
NonDisplay
Yes
Yes
N/A
N/A
SB2 Button
Programming Tips
Short press SB2 to enable/disable scan.
Use CPS for editing Scan List (adding/removing
Scan List
Yes
No
Yes
Yes
ON - All
channels to be scanned). For display models only:
Channels
you can add/delete channels in the scan list using
front panel by going into Programming Mode(1).
Feature available only for Non Display Models. For
Scan, Auto
Scan
No
Yes
No
Yes
OFF
front programming using front panel radio enter
Programming Mode(1)
Scramble (4)
Yes
No
Yes
Yes
OFF
(level 0)
Display models only: you can program scramble
using front panel by going into Programming
Mode(1).
Use CPS to program to program how long the PTT
can be pressed before the transmission is
Time-Out
Timer
No
No
Yes
Yes
60 seconds
automatically terminated. Values are 60, 120 and
180 seconds. (Pressing again PTT will start the
transmission again).
91
Programmable Via
RADIO PANEL
Features
Display
NonDisplay
Programmable via
CPS
Display
NonDisplay
Default Value
Programming Tips
Front panel radio programming available in display
VOX
Sensitivity
Level
Yes
No
Yes
Yes
OFF
(level 0)
models by pressing PTT or MENU buttons and
scrolling down/up with
and
buttons to set
value. Long press PTT to save.
Allows to use ‘hands-free’ mode connecting
microphone accessories. To enable connect
VOX, enable/
disable
Yes
Yes
Yes
Yes
OFF
external accessory and power up radio.
Note: The VOX sensitivity level default value is set
to OFF in the CPS settings. Before using this
feature, check VOX sensitivity level.
(1) To enter Programming Mode, press and hold both PTT and SB1 simultaneously for 3-5 seconds while turning radio ON (LED will start to blink
green). Short press PTT to get to the different programming options. For setting values, press
and
buttons.
(2) Using CPS you can prevent this feature to be programmed via front panel radio.
(3) Contact your Motorola Point of purchase for enabling this feature and/or for radio models details.
(4) For Non-Display Models, feature can be enabled for front panel programming by assigning feature to SB1 or SB2. For Display models:
Feature can be enabled to any of the programmable buttons rather than the default ones. For more details refer to Programming Buttons Chart
or CPS Menus.
92
Programmable Buttons Chart
Button
SB1
Monitor
Scan /
Nuisance
Delete
Call Tone Power Select Scramble
Default
SB2
BUTTON A (*)
BUTTON B (*)
BUTTON C (*)
Default
Backlight
Channel
Preset 1
Channel
Preset 2
N/A
N/A
N/A
N/A
N/A
N/A
No Operation
Default
Default
Default
Notes:
•
Buttons come programmed to default functions. Using CPS you can assign one of the features shown in the chart, so the button can toggle values
•
(*) Display models only.
using radio front panel
93
Icons Chart
Icon
Symbol
Comments
Battery Level
Displayed during normal radio mode operation, displays battery life remaining
Channel
Displayed during normal radio operation and when programming channel features
Code
Displayed during normal radio operation and when programming codes features
Frequency
Displayed during normal radio operation and when programming frequency features
Keypad lock
Displayed whenever the Keypad lock feature is enabled (keypad is locked)
Program
Displayed whenever the radio is set up to Programming Mode.
Scan
Scramble
94
Displayed whenever the radio is set to SCAN mode.
Displayed whenever scramble is enabled.
Icon
Symbol
Comments
Power Select
Displayed whenever the channel is transmitting or set to a high-power selection
Signal
Strength
RSSI Display Icon numbers of bars will indicate the strength of the received signal.
Vox/IVox
Displayed when IVOX/VOX enabled or when programming MIC / MIC gain features.
95
© 2007 Motorola Inc. All rights reserved.
Motorola Technology Sdn Bhd (Co. No. 455657-H)
Plot 2 Bayan Lepas Technoplex Industrial Park
Mukim 12 S.W.D
11900 Penang, Malaysia
Printed in Malaysia
September 2007
*6871663M01*
6871663M01-A

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
Signing Date                    : 2007:10:05 17:55:54+08:00
Signing Authority               : ARE_Acrobat Collaboration V7.0 P9 0000109
Annotation Usage Rights         : Create, Delete, Modify, Copy, Import, Export
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : FrameMaker 7.1
Modify Date                     : 2007:10:05 17:55:55+08:00
Create Date                     : 2007:10:05 17:09:46Z
Metadata Date                   : 2007:10:05 17:55:55+08:00
Format                          : application/pdf
Title                           : 63M01_A_BRUS_en.book
Creator                         : cei004
Document ID                     : uuid:16b6a25e-573a-4193-bce3-f43c84f9739b
Instance ID                     : uuid:6949c62f-fccc-40d5-b1d0-e3ce0b3df2ed
Has XFA                         : No
Page Count                      : 99
Author                          : cei004
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ489FT4882

Navigation menu