Motorola Solutions 89FT4900 PORTABLE 2-WAY RADIO WITH BT User Manual 2000044 C CLP en

Motorola Solutions, Inc. PORTABLE 2-WAY RADIO WITH BT 2000044 C CLP en

Contents

Users Manual

Download: Motorola Solutions 89FT4900 PORTABLE 2-WAY RADIO WITH BT User Manual 2000044 C CLP en
Mirror Download [FCC.gov]Motorola Solutions 89FT4900 PORTABLE 2-WAY RADIO WITH BT User Manual 2000044 C CLP en
Document ID1397566
Application ID4HdYiTo4ROZLqRyOex4qxA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize339.82kB (4247767 bits)
Date Submitted2010-12-28 00:00:00
Date Available2010-12-28 00:00:00
Creation Date2010-11-16 09:07:48
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2010-12-27 14:04:56
Document Title2000044-C_CLP_en.book
Document CreatorFrameMaker 8.0
Document Author: MHDW87

CLP Series Two-Way RadioTM
User Guide
Model CLP1010, CLP1040, and CLP1060 (with Bluetooth® Wireless Technology)
Document Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express
written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in
any form or by any means, electronic or mechanical, for any purpose without the express written
permission of Motorola.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However,
no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes
to any products herein to improve readability, function, or design. Motorola does not assume any liability
arising out of the applications or use of any product or circuit described herein; nor does it cover any
license under its patent rights nor the rights of others.
CONTENTS
Computer Software Copyrights . . . . . . . . . iii
Product Safety and RF Exposure
Compliance . . . . . . . . . . . . . . . . . . . . . . iv
FCC Licensing Information . . . . . . . . . . . . .v
Interference Information . . . . . . . . . . . . . . . . . v
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
Radio Overview . . . . . . . . . . . . . . . . . . . . . . .2
Radio Controls. . . . . . . . . . . . . . . . . . . . . . . . .2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . .3
Install The Battery . . . . . . . . . . . . . . . . . . . . . .3
Connecting a Wired Audio Accessory. . . .4
Connecting a Bluetooth Wireless Accessory
(Select Models Only) . . . . . . . . . . . . . . . . . . . .5
Add Bluetooth Headset
(Initial Pairing) . . . . . . . . . . . . . . . . . . . . . .5
Reconnect to Last Connected
Bluetooth Headset . . . . . . . . . . . . . . . . . .5
Battery and Charger Features. . . . . . . . . . 12
Battery Features. . . . . . . . . . . . . . . . . . . . . .
About the Li-Ion Battery . . . . . . . . . . . . .
Battery Recycling and Disposal . . . . . . .
Removing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . . . .
12
12
13
14
CONTENTS
Radio Frequency (RF) Exposure Safety
Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Erase Bluetooth Headset History
and Add Bluetooth Headset. . . . . . . . . . . 5
Turning the Radio On and Off . . . . . . . . . 6
Adjusting the Volume . . . . . . . . . . . . . . . . 6
Installing and Removing the
Swivel Belt Clip Holster . . . . . . . . . . . . . . 6
Transmitting and Receiving . . . . . . . . . . . . . . 7
Operation with Menu Settings . . . . . . . . . . . . 8
Selecting a Channel. . . . . . . . . . . . . . . . . 9
Monitoring a Channel. . . . . . . . . . . . . . . 10
Scanning . . . . . . . . . . . . . . . . . . . . . . . . 10
Dynamic Talkaround Scan (*) . . . . . . . . 11
Sending Call Tone (enabled
through CPS) . . . . . . . . . . . . . . . . . . . . . 11
Mute Feature (*). . . . . . . . . . . . . . . . . . . 11
Talk Permit Tone (*). . . . . . . . . . . . . . . . 11
CONTENTS
Power Supply, Adapter and Drop-in
Tray Charger. . . . . . . . . . . . . . . . . . . . . .14
Charging the Battery . . . . . . . . . . . . . . . .15
Charging the Bluetooth Headset. . . . . . .18
Checking Battery Status . . . . . . . . . . . . .19
Advanced Radio Configuration (*) . . . . . . 29
Batteries and Chargers Safety
Information. . . . . . . . . . . . . . . . . . . . . . . . . .20
CLP Repeater Capability . . . . . . . . . . . . . . . 30
Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 30
Operational Safety Guidelines . . . . . . . .21
Programming The Radio Through
the CPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Downloading the (Customer
Programming Software) CPS . . . . . . . . .22
Radio Cloning . . . . . . . . . . . . . . . . . . . . . . .25
Cloning Radio Settings . . . . . . . . . . . . . . . . .25
Cloning Instructions. . . . . . . . . . . . . . . . . . . .25
Cloning Radios using the CLP Series
Cloning Cable Kit P/N HKKN4026
(optional accessory) . . . . . . . . . . . . . . . .25
Cloning Radios using the CLP Series
Multi-Unit Charger (MUC) Kit
P/N HKPN4007 (optional accessory) . . .28
ii
Entering Advanced Radio
Configuration Mode . . . . . . . . . . . . . . . . 29
CLP Repeater Capability: Working with
RPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Troubleshooting. . . . . . . . . . . . . . . . . . . . . 32
Use and Care . . . . . . . . . . . . . . . . . . . . . . . 36
Radio Frequency and Code Charts . . . . . 37
Motorola Limited Warranty for the
United States and Canada. . . . . . . . . . . . . 41
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 46
Audio Accessories . . . . . . . . . . . . . . . . . . . .
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carry Accessories . . . . . . . . . . . . . . . . . . . .
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Cables . . . . . . . . . . . . . . . . . .
46
46
46
47
47
COMPUTER SOFTWARE
COPYRIGHTS
iii
COMPUTER SOFTWARE
COPYRIGHTS
The Motorola products described in this
manual may include copyrighted Motorola
computer programs stored in semiconductor
memories or other media. Laws in the United
States and other countries preserve for
Motorola certain exclusive rights for
copyrighted computer programs, including, but
not limited to, the exclusive right to copy or
reproduce in any form the copyrighted
computer program. Accordingly, any
copyrighted Motorola computer programs
contained in the Motorola products described in
this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in
any manner without the express written
permission of Motorola.
Furthermore, the purchase of Motorola
products shall not be deemed to grant either
directly or by implication, estoppels, or
otherwise, any license under the copyrights,
patents or patent applications of Motorola,
except for the normal non-exclusive license to
use that arises by operation of law in the sale of
a product.
RADIO FREQUENCY (RF)
EXPOSURE SAFETY
STANDARDS
Product Safety and RF Exposure
Compliance
RF SAFETY STANDARDS
Caution
Before using this product, read the
operating instructions for safe
usage contained in the Product
Safety and RF Exposure booklet
contained with your radio.
ATTENTION!
This radio is restricted to occupational use only to
satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy
awareness information and operating instructions in
the Product Safety and RF Exposure booklet
enclosed with your radio (Motorola Publication part
number 6881095C98) to ensure compliance with RF
energy exposure limits.
iv
For a list of Motorola-approved antennas, batteries,
and other accessories, visit the following website:
www.motorola.com/CLP
INTERFERENCE INFORMATION
This device complies with Parts 90 and 15 of the FCC
Rules. Operation is subject to the condition that this
device does not cause harmful interference.
The CLP Series radio operates on radio frequencies
that are regulated by the Federal Communications
Commission (FCC). To transmit on these frequencies,
you are required to have a license issued by the FCC.
Application is made available on FCC Form 601 and
Schedules D, H, and Remittance Form 159.
To obtain these FCC forms, request document
000601 which includes all forms and instructions. If
you wish to have the document faxed, mailed or have
questions, use the following contact information.
Faxed: Contact the
Fax-On-Demand
system at:
1-202-418-0177
Mailed: Call the FCC forms hotline
at:
1-800-418-FORM
1-800-418-3676
For questions regarding FCC
license, contact the FCC at:
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
FCC LICENSING
INFORMATION
FCC LICENSING
INFORMATION
FCC LICENSING
INFORMATION
Before filling out your application, you must decide
which frequency(ies) you can operate on: “Radio
Frequency and Code Charts” on page 37. For
questions on determining the radio frequency, call
Motorola Product Services at: 1-800-448-6686.
Changes or modifications not expressly approved by
Motorola may void the user’s authority granted by the
FCC to operate this radio and should not be made. To
comply with FCC requirements, transmitter
adjustments should be made only by or under the
supervision of a person certified as technically
qualified to perform transmitter maintenance and
repairs in the private land mobile and fixed services as
certified by an organization representative of the user
of those services.
vi
Replacement of any transmitter component (crystal,
semiconductor, etc.) not authorized by the FCC
equipment authorization for this radio could violate
FCC rules.
Use of this radio outside the country where it was
intended to be distributed is subject to government
regulations and may be prohibited.
PACKAGE CONTENTS
INTRODUCTION
Your product package contains the following products
and manuals:
•
CLP Series Two-way Radio™
•
Swivel Belt Clip Holster
•
Lithium Ion Battery and Battery Door
•
Drop-In Tray Charger with Transformer
•
Audio Accessory
•
User Quick Reference
•
Warranty Card
For product information, visit us at:
www.motorola.com/CLP
For product-related questions, contact:
1-800-448- 6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
This user guide covers the following CLP Series™ models (*):
Note:
Model
Frequency
Band
Transmit
Power
No. of
Channels
Bluetooth
CLP1010
UHF
1W
No
CLP1040
UHF
1W
No
CLP1060
UHF
1W
Yes
Certain models may or may not be available at the time of purchase.
INTRODUCTION
Thank you for purchasing a Motorola CLP Series
Two-Way Radio™. Your radio is a product of
Motorola’s 80 plus years of experience as a world
leader in designing and manufacturing
communications equipment. The CLP Series radios
provide cost-effective efficient communications for
businesses such as retail stores, restaurants, hotels,
and schools. Motorola professional two-way radios
are the perfect communications solution for all of
today’s fast-paced industries. Please read this guide
carefully so you know how to properly operate the
radio before use.
RADIO OVERVIEW
RADIO CONTROLS
Accessory
Connector
Power/Battery
Button
RADIO OVERVIEW
Volume
Control (+/-)
Menu Button
Smart Status
Glow
Push-to-Talk
(PTT) Button
GETTING STARTED
2.
Align the battery contacts with tabs in the battery
compartment. Insert the contact side of the
battery first, then press the battery down to
secure in place.
3.
Put the battery door back on the radio. Push
down the latch to lock.
INSTALL THE BATTERY
1.
The CLP Series radios’ standard packaged models come with standard Lithium Ion battery and the standard Lithium Ion
battery door. For option, customers can order Hi-capacity Lithium Ion battery (P/N HKNN4013) and the Hi-capacity Lithium
Ion battery door (P/N HKLN4440).
RADIO OVERVIEW
Note:
Push up the latch at the bottom of the battery
door and lift the battery door off the radio.
Connecting a Wired Audio Accessory
3.
Plug the audio accessory straight into the
accessory connector on the radio. Screw the
audio accessory plug into the connector until it
is tight and fully engaged with the connector.
4.
Turn the radio ON. Press either the Battery
Status, Menu or Volume Control button to
check for audio through the audio accessory.
RADIO OVERVIEW
Connect the wired audio accessory.
1.
Turn the radio OFF.
2.
Remove the accessory connector cover
(applicable on bluetooth enabled models only).
Note:
The CLP Series radios offer a variety of audio
accessories. For detailed Audio Accessories List,
please refer to www.motorola.com/CLP for
information on approved accessories. Lower the
radio volume BEFORE placing the audio accessory
in or near your ear.
CONNECTING A BLUETOOTH WIRELESS
ACCESSORY (SELECT MODELS ONLY)
Note:
Add Bluetooth Headset (Initial Pairing)
Reconnect to Last Connected Bluetooth
Headset
1.
Turn the radio OFF.
2.
Put Bluetooth headset in pairing mode. Refer to
your Bluetooth headset instructions leaflet.
3.
1.
Turn the radio OFF.
2.
Press the power button to turn the radio ON.
(Make sure the Bluetooth headset is turned
ON).
Press and hold the PTT button and power
button simultaneously until radio shows the blue
LED.
Erase Bluetooth Headset History and Add
Bluetooth Headset
LED Configuration
User Mode
Bluetooth
Pairing Mode
LED Status
Last connection
– Fast blinking
blue
•
Add or erase/
add – Solid blue
Pairing
Successfully
Blue/purple blinks for
5 seconds
Bluetooth
Disconnected
Red/purple blinks
until the radio
reconnects
Pairing Fail/
Timeout
Color
1.
Turn the radio OFF.
2.
Put the Bluetooth headset in pairing mode.
Refer to your Bluetooth headset Instructions
leaflet.
3.
Press and hold the PTT button and power
button simultaneously until radio shows the blue
LED.
Note:
The CLP radio uses proximity pairing. Make sure
the headset is close enough to the CLP radio.
Pairing process takes about 14 seconds.
Red/purple blinks
until radio reconnects
RADIO OVERVIEW
•
The Bluetooth feature is disabled when the wired
audio accessory is plugged into the accessory
connector on the CLP radio.
Turning the Radio On and Off
•
To turn the radio ON, press and hold the Power/
Battery button until you hear a short tone and the
Smart Status Glow lights up.
•
To turn it OFF, press and hold the button until you
hear a short tone and the Smart Status Glow
(red) indicator blinks once.
Adjusting the Volume
Turn the radio ON and set volume level by
pressing volume control (+/- button). A total of 16
volume levels are available.
RADIO OVERVIEW
Installing and Removing the Swivel Belt
Clip Holster
1.
Slide the bottom of the radio into the holster.
2.
Snap the top of the holster into the radio around
the accessory connector.
3.
To remove the holster, pull either the top or
bottom tab(s) and pull the radio from the holster.
Note:
4.
When using a corded audio accessory, loop the
cord into the recess in the rear of the holster for
optimal plug retention.
Make a small loop in the cord. Pass the cord
through the cord guide, nest the cord in the
U-shaped groove. Pull tight to lock the cord in
place.
5.
Turn the belt clip to the position as needed.
Cord
Guide
U-Shaped
Groove
TRANSMITTING AND RECEIVING
1.
To talk, press and hold the PTT button on the
front of the radio (or on select wired audio
accessories with an inline PTT). Speak clearly
into the microphone on the audio accessory.
When finished talking, release the PTT to listen.
2.
To receive, listen through the earpiece at the
volume level you have set. Press the PTT to
respond.
Note:
The CLP Series radios always require the use of an
audio accessory with microphone and speaker.
Talk Range
Note:
Multi-Level
Inside steel/concrete
industrial buildings
Inside Multi-Level
Buildings
Up to 160,000 square
feet
Up to 12 floors
RADIO OVERVIEW
The CLP Series radios offer a variety of flexible
carrying accessories. For detailed Carrying
Accessories List, please refer to
www.motorola.com/CLP for information on
approved accessories.
Industrial
OPERATION WITH MENU SETTINGS
Press Menu button to navigate through the Menu settings. Voice Assisted Operation feature* (* may not be
available on certain previous shipping radios) At any time in Menu mode, short press PTT or wait 3
seconds to exit the menu.
RADIO OVERVIEW
HOW TO...
STEP 1
STEP 2
Change Channel
Press Menu button to navigate to Channel.
Press +/- button to change
channel.
Enter Monitor Mode
Press Menu button to navigate to Monitor.
Press +/- button to activate or
deactivate Monitor.
Enter Scan Mode
Press Menu button to navigate to Scan.
Press +/- button to activate or
deactivate Scan.
Send Call Tone (enabled
through CPS)
Press Menu button to navigate to Call
Tone.
Press +/- button to send Call
Tone.
Quick Tip: It is not necessary to wait for the voice prompt to be completed before continuing with next button press.
Note: For single channel models, Monitor, Scan Mode and Call Tone are supported. Single channel models support Scan mode
when the user enables “Dynamic Talkaround Scan” on a repeater channel via the customer programming software.
Selecting a Channel
•
For CLP multi-channel models only:
1.
When powered ON, press the Menu button, you
can hear the voice prompt:
2.
[Color] “Channel” – [Channel#] – “To change” –
“press +/-”
Select the channel you want. The LED reflects
the color of the new channel. Press PTT button
to confirm or it is activated after 3 second hang
time.
Default Channel Settings for CPS
CLP1010 Single-Channel Models
Channel
LED Status
Color
Red
CLP1040 Multi-Channel Models
Channel
Color
Red
Channel
LED
Status
Color
Red
Green
Green
Orange
Orange
Blue
RADIO OVERVIEW
LED
Status
CLP1060 MultiChannel Models
Blue
Purple
White
Monitoring a Channel
1.
1.
To activate, press the Menu button to navigate
to Monitor mode.
Press the Menu button to navigate to Scan
mode.
2.
2.
When Monitor is OFF, you can hear the voice
prompt: “Monitor” – “To activate” – “press +/-”.
When Scan is OFF, you can hear the voice
prompt: “Scan” – “To activate” – “press +/-”.
3.
3.
Press either “+/-“ button to activate the Monitor;
press either “+/-“ button again to deactivate.
Press either “+/-“ button to activate the Scan;
press either “+/-“ button again to deactivate.
4.
When Scan is on, you can hear the voice
prompt: “Scan” – “To deactivate” – “press +/-”
button.
RADIO OVERVIEW
Note:
When Monitor is ON, you can hear static if no
activity is present or audio if channel activity is
present.
4.
To engage the Monitor mode, enable Monitor via
the menu and let the menu time out.
5.
To deactivate, press PTT during Monitor Menu
mode.
Scanning
For multi-channel models only
You can scan up to 4 channels on CLP1040
models and scan up to 6 channels on CLP1060
models. When the radio detects activity, it stops
scanning and locks in on the active channel. This
allows you to talk and listen to the person
transmitting without changing channels.
10
Dynamic Talkaround Scan (*)
Mute Feature (*)
"Dynamic Talkaround Scan" is a simple but
effective method for an on-site repeater enabled
two-way radio systems to maximize
communication coverage. This feature can be
enabled on a repeater channel via the Customer
Programming Software (CPS). The Dynamic
Talkaround Scan gives the radio the ability to scan
both the transmit and receive frequencies of a
repeater channel.
You can quickly lower the headset volume using
the Mute feature.
Note:
(*) Enhancement feature on CLP Radios. May not
be available on previous shipping radios. The
Dynamic Talkaround Scan is given higher priority
then the Scan Mode. If the Dynamic Talkaround
Scan and Scan is enabled on the home channel,
then the radio can only support the Dynamic
Talkaround Scan.
1.
Press the Menu button to navigate to Call Tone.
2.
Press either “+/-“ button to transmit selected
Call Tone.
Note:
There are 4 Call Tones available.
Press and hold + or - button while receiving
audio to quickly lower the headset volume to
“Mute Headset Volume” setting (configurable via
CPS). You can hear the voice prompt: "Mute"
2.
To switch back to the previous headset volume
setting, press and hold + or - button again. You
can hear the voice prompt: "Unmute".
Note:
(*) Enhancement feature on CLP radios. May not
available on previous shipping radios. The
enhanced CLP does not support the volume scroll
like the previous CLP models.
Talk Permit Tone (*)
In mixed fleet situations (CLP1010 or CLP1040 and
CLP1060), Bluetooth users may miss some words
due to the Bluetooth connection not being
established. Talk Permit Tone allocates some time so
that the link between the radio and headset gets
reestablished thus minimizing the lost words. The Talk
Permit Tone is enabled as default on CPS on the
Bluetooth models.
Note:
(*) Enhancement feature on CLP radios; may not
available on previous shipping radios. The Talk
Permit Tone is enabled as default on the Bluetooth
models. It is not enabled on non-Bluetooth models
(default mode is OFF).
11
RADIO OVERVIEW
Sending Call Tone (enabled through CPS)
1.
BATTERY AND CHARGER
FEATURES
BATTERY AND CHARGER
FEATURES
BATTERY FEATURES
The CLP Series radio provides Lithium-Ion batteries
that come in different capacities that define the battery
life.
About the Li-Ion Battery
The CLP Series radio comes equipped with a
rechargeable Li-Ion battery. This battery should be
charged before initial use to ensure optimum capacity
and performance.
Battery life is determined by several factors. Among
the more critical are the regular overcharge of
batteries and the average depth of discharge with
each cycle. Typically, the greater the overcharge and
the deeper the average discharge, the fewer cycles a
battery can last. For example, a battery which is
overcharged and discharged 100% several times a
day, lasts fewer cycles than a battery that receives
less of an overcharge and is discharged to 50% per
day. Further, a battery which receives minimal
overcharging and averages only 25% discharge, lasts
even longer.
12
Motorola batteries are designed specifically to be
used with a Motorola charger and vice versa.
Charging in non-Motorola equipment may lead to
battery damage and void the battery warranty. The
battery should be at about 77 °F (25 °C) (room
temperature), whenever possible. Charging a cold
battery (below 50 °F [10 °C]) may result in leakage of
electrolyte and ultimately in failure of the battery.
Charging a hot battery (above 95 °F [35 °C]) results in
reduced discharge capacity, affecting the performance
of the radio. Motorola rapid-rate battery chargers
contain a temperature-sensing circuit to ensure that
batteries are charged within the temperature limits
stated above.
Battery Life
Based on 5% transmit, 5% receive, 90% standby
(standard duty cycle):
Estimated Battery Life
Standard
Charging
Solution
CLP1010,
CLP1040
CLP1060
Battery Type
Standard Li-Ion
Battery
High Capacity
Li-Ion Battery
12 hours
18 hours
9 hours
14 hours
Battery Recycling and Disposal
Many retailers and dealers participate in this program.
For the location of the drop-off facility closest to you,
access RBRC's Internet web site at:
http://www.call2recycle.org or call:
1- 877-723-1297.
This internet site and telephone number also provides
other useful information concerning recycling options
for consumers, businesses and governmental
agencies.
13
BATTERY AND CHARGER
FEATURES
Li-Ion rechargeable batteries can be recycled.
However, recycling facilities may not be available in all
areas. Under various U.S. state laws and the laws of
several other countries, batteries must be recycled
and cannot be disposed of in landfills or incinerators.
Contact your local waste management agency for
specific requirements and information in your area.
Motorola fully endorses and encourages the recycling
of Li-Ion batteries. In the U.S. and Canada, Motorola
participates in the nationwide Rechargeable Battery
Recycling Corporation (RBRC) program for Li-Ion
battery collection and recycling.
BATTERY AND CHARGER
FEATURES
Removing the Lithium-Ion (Li-Ion) Battery
Power Supply, Adapter and Drop-in Tray
Charger
Battery
Latch
1.
Turn OFF the radio.
2.
Push up the latch at the bottom of the battery
door and lift the battery door off the radio.
3.
Pull the battery away from the radio.
14
The radio is packaged with one Drop-in Tray Charger
with transformer. For details, see “Chargers” Section
on page 47.
Charging the Battery
Charging a Standalone Battery
1.
Note:
BATTERY AND CHARGER
FEATURES
To charge the battery (with the radio attached):
Place it in a Motorola-approved Drop-in Tray
Single Unit Charger or Drop-in Tray Multi Unit
Charger.
When acquiring additional chargers or power
supplies, make sure you have similar drop-in tray
chargers and power supplies sets. For part number
details, refer to “Chargers” Section on page 47.
Estimated Charging Time
The following table provides the estimated charging
time of the battery.
Estimated Charging Time
To charge only the battery:
1.
Insert the battery into the tray, with the inside
surface of the battery facing the front of the
charger, as shown.
2.
Ensure the slots in the battery correctly engage
in the charger.
Battery Type
Charging
Solution
Standard
Charging
Solution
Standard Li- Ion
Battery
2.5 hours
High Capacity
Li-Ion Battery
3.5 hours
For further details, see “Batteries” Section on page 46.
15
BATTERY AND CHARGER
FEATURES
Charging with the Drop-in Tray
Single Unit Charger (SUC)
1.
Place the drop-in tray charger on a flat surface.
2.
Insert the connector of the power supply into the
Micro USB port on the front of the drop-in tray
charger.
3.
Connect the correct power supply to a proper
AC outlet.
4.
Insert the radio into the tray, making sure the
charging contacts on the charger are aligned
with the contacts on the radio.
Note:
When charging a battery attached to a radio, turn
the radio OFF to ensure a full charge. The radio fits
in the charger with the holster attached when
placed face down in the tray.
16
Charging with the Drop-In Tray
Multi-Unit Charger (Optional
Accessory)
The Multi-Unit Charger (MUC) allows drop-in
charging of up to 6 radios. Each of the 6 charging
pockets can hold a radio (with battery installed).
The Multi-Unit Charger provides pockets for
headset storage.
1.
Place the charger on a flat surface or mount it
on the wall.
2.
Insert the power cord plug into the jack on the
MUC.
3.
Plug the cord into an AC outlet and then into
charger.
4.
Turn the radio OFF.
Note:
Note:
•
For part number details, refer to the“Accessories”
Section on page 46.
Insert the radio (with battery installed) into the
charging pocket.
The radio fits in the charger with the holster
attached when placed face down in the tray. The
battery can be charged by itself using the slot on
the flat surface of the charging pocket.
Charger LED Indicator
Status
On the MUC, each of the 6 charging pockets has
an LED. The LEDs are grouped into pairs to show
which charging pockets are paired. The LED is red
when the battery is charging. It turns to green
once the battery is fully charged.
Note:
This Multi Unit Charger allows you to clone up to 2
radios (2 Source radios and 2 Target radios). For
more details, refer to “Radio Cloning” Section on
page 25.
Comments
Charging
Steady
Red
Indication
The charger is
currently charging.
Charge
Complete
Steady
Green
Indication
Battery is fully
charged.
Charging Status LEDs
On the drop-in charger, the radio charging pocket
has an LED Charger.
LED Status
Battery
Fault (*)
Note:
Note:
Blinking
Red
Battery was faulty
when inserted.
The LED is red when the battery is charging. It turns
to green once the battery is fully charged.
(*) Re-seating the battery pack likely corrects this
issue.
17
BATTERY AND CHARGER
FEATURES
5.
If the radio is ON while charging, it takes longer to
fully charge.
BATTERY AND CHARGER
FEATURES
Charging the Bluetooth Headset
•
Refer to your Bluetooth headset leaflet for charging
instruction.
Note:
Charging Bluetooth Headset with CLP
Series Drop-In Tray Multi-Unit Charger
and Cloning Cable (Optional Accessory)
You can also charge your Bluetooth headset with
CLP Series Multi Unit Charger (MUC) P/N
HKPN4007 (optional accessory) and Cloning
Cable P/N HKKN4026 (optional accessory).
•
Plug one side of the cloning cable
microconnector to the USB port of the Multi-Unit
Charger (there are 6 USB port on top of the
accessory pockets)
18
Plug the other end of the cloning cable to the
USB port of the Bluetooth headset for charging
Refer to the charging status light on your Bluetooth
headset leaflet.
Checking Battery Status
After the Smart Status Glow and Voice Assisted
Operation features (*) indicate the BATTERY
STATUS, it returns to the current channel color.
Note:
(*) May not be available on certain previous
shipping radios.
Battery Status
Level
LED
Status
Color
Battery Level High (70 –100%)
Green
Battery Level Medium (30 – 70%)
Orange
Battery Level Low (10 – 30%)
Red
Battery Level Critical (0 – 10%)
Blinking
Red
19
BATTERY AND CHARGER
FEATURES
When powered on, short press and release the
Power/Battery button, the Smart Status Glow and
Voice Assisted Operation features (* ) gives you
the battery status of the radio.
BATTERIES AND CHARGERS
SAFETY INFORMATION
BATTERIES AND
CHARGERS SAFETY
INFORMATION
3.
To reduce risk of damage to the electric plug
and cord, pull by the plug rather than the cord
when disconnecting the charger.
4.
An extension cord should not be used unless
This document contains important safety and
absolutely necessary. Use of an improper
operating instructions. Read these instructions
extension cord could result in risk of fire and
carefully and save them for future reference.
electric shock. If an extension cord must be
Before using the battery charger, read all the
used, make sure that the cord size is 18 AWG
instructions and cautionary markings on
for lengths up to 6.5 feet (2.0 m), and 16 AWG
•
•
the battery, and
•
the radio using the battery
1.
5.
To reduce risk of fire, electric shock, or injury, do
not operate the charger if it has been broken or
damaged in any way. Take it to a qualified
To reduce risk of injury, charge only the
rechargeable Motorola-authorized batteries.
2.
for lengths up to 9.8 feet (3.0 m).
the charger,
Motorola service representative.
6.
Do not disassemble the charger; it is not
Other batteries may explode, causing personal
repairable and replacement parts are not
injury and damage.
available. Disassembly of the charger may
Use of accessories not recommended by
Motorola may result in risk of fire, electric
shock, or injury.
result in risk of electrical shock or fire.
7.
To reduce risk of electric shock, unplug the
charger from the AC outlet before attempting
any maintenance or cleaning
20
OPERATIONAL SAFETY GUIDELINES
Turn the radio OFF when charging battery.
•
The charger is not suitable for outdoor use. Use
only in dry locations/conditions.
•
Connect charger only to an appropriately fused
and wired supply of the correct voltage (as
specified on the product).
•
Disconnect charger from line voltage by removing
main plug.
•
The outlet to which this equipment is connected
should be nearby and easily accessible.
•
Maximum ambient temperature around the power
supply equipment must not exceed 40 °C
(104 °F).
•
Make sure that the cord is located where it cannot
be stepped on, tripped over, or subjected to
water, damage, or stress.
BATTERIES AND CHARGERS
SAFETY INFORMATION
•
21
PROGRAMMING THE
RADIO THROUGH THE CPS
RADIO PROGRAMMING OVERVIEW
Downloading the (Customer Programming
Software) CPS
Programming the Radio
To program the radio:
1.
Connect the radio via the Drop-in Charger Tray
or the Charging Pocket with “PROG” label on
the Multi-Unit Charger and CPS Programming
Cable.
PROGRAMMING THE RADIO
THROUGH THE CPS
You can program or change features on your CLP
radios by using the Computer Programming Software
(CPS) and the CPS Programming Cable (*). CPS
software is available for free as web based
downloadable software at: www.motorola.com/CLP
After downloading the CPS, install the software to
your computer.
Programming the Radio through a Single Unit
Charger
Programming the Radio through a Multi-Unit
Charger
22
2.
Make sure the radio is turned ON.
3.
Once the radio is connected, open the CPS and
select “Read” on the toolbar to get the radio
profile. The CPS allows the user to change
settings, such as General, Audio, Menu,
Channels, Scan List, Customized PL/DPL,
Bluetooth (*) as well as select frequencies, PL/
DPL codes on each channel.
4.
After you change the settings, press “Write” on
the toolbar to save the settings.
For more information on the Computer Programming
Software, please refer to Help menu on the CPS.
Note:
Your radio is programmed at the factory to the
following settings:
CLP1010 1W UHF 1 CH Radios Default Settings - BRUS
Channel
Frequency
Frequency
Setting
Code
Value
(Hz)
Band
width
(kHz)
464.5500
67.0
12.5
CLP1040 1W UHF 4 CH Radios Default Settings - BRUS
Channel
Frequency
Frequency
Settings
Code
Value
(Hz)
Band
width
(kHz)
464.5500
67.0
12.5
467.9250
67.0
12.5
467.8500
67.0
12.5
467.8750
67.0
12.5
23
PROGRAMMING THE RADIO
THROUGH THE CPS
Note:
(*) CPS Programming Cable (P/N HKKN4025) is an
accessory sold separately. Please contact your
Motorola Point of Purchase for more information.
(*) Bluetooth is available on selected models only.
Factory Default Settings
CLP1060 1W UHF 6 CH Bluetooth Radios Default
Settings - BRUS
Frequency
Frequency
Settings
Code
Value
(Hz)
Band
width
(kHz)
464.5500
67.0
12.5
467.9250
67.0
12.5
467.8500
67.0
12.5
467.8750
67.0
12.5
10
461.0625
67.0
12.5
12
461.1125
67.0
12.5
PROGRAMMING THE RADIO
THROUGH THE CPS
Channel
24
RADIO CLONING
CLONING RADIO SETTINGS
A multi-channel radio can be cloned to a singlechannel radio BUT only the first channel is cloned.
The Multi-Unit Charger (MUC) does not have to be
plugged in for cloning, but both radios require
charged batteries.
Note:
The enhanced CLP software also uses the
LED to indicate “pass” or “fail” status during
cloning. Green LED during cloning indicates
“pass” status and red LED during cloning
indicates “fail” status.
Cloning Radios using the CLP Series
Cloning Cable Kit P/N HKKN4026 (optional
accessory)
Cloning the Radio through a Single
Unit Charger
Source Radio: Radio to be cloned
Target Radio: Radio to which the configuration of the
“Source Radio” is to be copied.
Before beginning the cloning process, make
sure you have:
• A fully charged battery on each one of the
radios
• Two CLP Series Single Unit Charger (SUC) Kits
• Both radios are turned OFF
1.
Unplug any cables (power supply or USB
cables) from the Single Unit Chargers.
25
RADIO CLONING
You can copy the CLP Series radio settings from
one radio (the source) to a second radio using the
CLP Series Single Unit Charger (SUC) Kit P/N
HKPN4008 and CLP Series Cloning Cable Kit P/N
HKKN4026 (optional accessory) or CLP Series
Multi-Unit Charger (MUC) Kit P/N HKPN4007
(optional accessory).
CLONING INSTRUCTIONS
RADIO CLONING
2.
Note:
Plug one side of the cloning cable
microconnector to one Single Unit Charger.
Plug the other end to the second Single Unit
Charger.
During the cloning process no power is
being applied to the Single Unit Charger.
The batteries cannot be charged. A data
communication is being established
between the two radios.
3.
Turn ON the “Target Radio” and place it into
one of the Single Unit Chargers.
4.
On the “Source Radio”, power the radio
following the sequence below:• Press and
hold the Push-to-Talk (PTT) and the “-“Button
simultaneously while turning the radio ON
until you hear the Cloning Tone and Double
Blinking Orange
on the Smart Status
Glow.
5.
Place the “Source Radio” in its Single Unit
Charger with an Audio accessory, then press
and release Menu Button to start the cloning
process.
26
6.
After cloning is completed, the “Source
Radio” sounds either a “pass” tone (cloning
was successful) or a “fail” tone (cloning
process has failed). The pass tone sounds
like a good key “chirp” whereas the “fail” tone
sounds similar to a “bonk” tone.
(A tone is heard in no more than 5 seconds).
7.
Once you have completed the cloning
process, you should turn the radios “OFF”
and “ON” to bring them to normal user mode
(exit “clone” mode).
What to do if cloning fails
The radio emits an audible “bonk” indicating
that the cloning process has failed. In the event
following before trying to start the cloning
process again.
1.
Make sure that the radio batteries on both
radios are fully charged.
2.
Verify the cloning cable connection on both
Single Unit Chargers.
3.
Make sure that the battery is engaged
properly on to the radio.
4.
Make sure that there is no debris in the
charging tray or on the radio contacts.
5.
Verify that the source radio is in cloning
mode.
6.
Make sure that the radio to be cloned is
turned ON.
7.
Make sure that radios are both from the
same type (same frequency band, same
region and same transmission power).
This cloning cable is designed to operate
only with compatible Motorola Drop-in Tray
Single Unit Charger. When ordering the
cloning cable, please refer to CLP Series
Cloning Cable Kit P/N HKKN4026. For
details about accessories, refer to
"Accessories" Section on page 46.
27
RADIO CLONING
that cloning fails, try performing each of the
Note:
RADIO CLONING
Cloning Radios using the CLP Series MultiUnit Charger (MUC) Kit P/N HKPN4007
(optional accessory)
Cloning the Radio through a Multi-Unit
Charger
1.
To put the source radio into clone mode,
press and hold PTT and the “-” button while
turning the radio ON until you hear the
Cloning Tone and Double Blinking Orange
on the Smart Status Glow.
2.
Place the source radio into one of the
charging pockets that has the “CLONE”
label.
28
3.
Turn the target radio ON and place it in the
pairing charging pocket that has the
“CLONE” label and start the cloning process.
4.
Press the “Menu” button on the source radio
to start the cloning process. The source
radio generates the start clone tone.
5.
Once the cloning is completed, turn the
target radio OFF and back ON again in order
to activate the radio.
6.
To clone another radio, repeat steps 3, 4 and
5.
7.
To exit clone mode on the source radio, turn
the radio OFF.
ADVANCED RADIO
CONFIGURATION (*)
(*) Enhancement feature on CLP radios. May not
be available on previous shipping radios.
Advanced Radio Configuration provides you with
the ability to view and configure the following
settings without the need to use a computer.
1.
Press the PTT, + Button and Power button
and hold for 3 to 5 seconds until you hear a
“chirp” sound and the voice prompt
“Programming Mode”.
Note:
2.
•
The LED Indicator starts blinking a green heartbeat.
Press the Menu button to change the
settings on:
Channel (for multi-channel models)
RX frequency
• Frequencies
• Codes (CTCC/DPL)
•
TX frequency*
•
RX code
Frequencies allows the user to select frequencies
for each channel. Codes helps minimize
interference by providing the user with a choice of
code combinations that filter out static, noise, and
unwanted messages.
•
TX code*
• Channels
Entering Advanced Radio Configuration
Mode
Available when the device is powered OFF.
Note:
For Bluetooth models, makes sure the wired
accessory is connected or the Bluetooth headset is
paired before entering Advanced Radio
Configuration Mode.
Note:
TX frequencies and TX codes are only available for
repeater channels.
3.
The voice announcements indicate the menu
items and their current settings. To change,
press +/- button; to go to the next menu item,
press Menu button.
4.
Short press PTT or wait 15 seconds to exit
the menu.
5.
Press and hold the PTT button to exit the
Advanced Radio Configuration Mode.
29
ADVANCED RADIO
CONFIGURATION (*)
•
CLP REPEATER
CAPABILITY: WORKING
WITH RPX
Programming the RPX through a
Single Unit Charger
CLP REPEATER CAPABILITY
Use the Single Unit Charger or use the pocket with
“PROG” label on the Multi-Unit Charger to clone
the RPX.
CLP REPEATER CAPABILITY:
WORKING WITH RPX
Note:
Connect the RDX Serial Clone Cable (P/N
RLN6303) and the Mini-USB to the Micro-USB
Adapter Cable in order to link the CLP and RPX
units.
Programming the RPX through a Single Unit
Charger
INSTRUCTIONS
1.
To put the CLP radio into clone mode, press
and hold PTT and the “-” button while turning
the radio ON until you hear the Cloning Tone
and Blinking Orange
on the Smart Status
1.
Place the CLP radio into the charging
pocket.
2.
Connect the micro-USB plug of the microUSB adapter cable with the RDX Serial
Clone Cable into the micro-USB receptable
charging pockets.
3.
Connect the Mini-USB plug of the RDX
Serial Clone Cable into the RPX Mini-USB
receptable.
Glow.
30
4.
Press the “Menu” button on the CLP radio to
start the cloning process.
5.
Once the cloning is completed, turn the RPX
OFF and back ON again in order to activate
the radio.
6.
To clone another RPX, repeat steps 3, 4 and
5.
7.
To exit clone mode on the CLP radio, turn the
radio OFF.
Programming the RPX through a
Multi-Unit Charger
1.
Place the CLP radio into one of the charging
pockets that has the “PROG” label indicated.
2.
Connect the micro-USB plug of the microUSB adapter cable with the RDX Serial
Clone Cable into the micro-USB receptable
charging pockets with the “PROG” label
indicated.
3.
Follow steps 4 through 7 under
"Programming the RPX through a Single Unit
Charger" on page 30.
31
CLP REPEATER CAPABILITY:
WORKING WITH RPX
Programming the RPX through a Multi-Unit
Charger
TROUBLESHOOTING
TROUBLESHOOTING
Symptom
Try this
No Power
Recharge or replace Li-Ion battery.
Extreme operating temperatures affect battery life.
Refer to “About the Li-Ion Battery” Section on page 12.
Hearing other noises or
conversation on a channel
Confirm Interference Eliminator Code is set.
Frequency or Interference Eliminator Code may be in use.
Change settings: either change frequencies or codes on all
radios.
Make sure radio is at the right frequency and code when
transmitting.
Message Scrambled
Scramble Code might be ON, and/or setting does not match
other radios' settings. Use CPS to change settings.
Audio quality not good enough
Radio settings might not be matching up correctly.
Double check frequencies, codes and bandwidths to ensure
they are identical in all radios.
32
Try this
Limited talk range
Steel and/or concrete structures, heavy foliage, buildings or
vehicles decrease range. Check for clear line of sight to
improve transmission.
Change location of radio. To increase range and coverage, you
can either reduce obstructions or increase power.
UHF radios provide greater coverage in industrial and
commercial buildings.
Increasing power provides greater signal range and increased
penetration through obstructions.
Message not transmitted/
received
Make sure the PTT button is completely pressed when
transmitting.
Confirm that the radios have the same Channel, Frequency,
Interference Eliminator Code and Scramble Code settings.
Refer to “Transmitting and Receiving” Section on page 7.
Recharge, replace and/or reposition batteries. Refer to “About
the Li-Ion Battery” Section on page 12.
Obstructions and operating indoors, or in vehicles, may
interfere. Change location.
Verify that the radio is not in Scan mode. Refer to “Scanning”
Section on page 10.
33
TROUBLESHOOTING
Symptom
TROUBLESHOOTING
Symptom
Try this
Heavy static or interference
Radios are too close, they must be at least five feet apart.
Radios are too far apart or obstacles are interfering with
transmission.
Low batteries
Recharge or replace Li-Ion battery.
Extreme operating temperatures affect battery life.
Refer to “About the Li-Ion Battery” Section on page 12.
Drop-in Charger LED light does
not blink
Check radio/battery is properly inserted and check battery/
charger contacts to ensure they are clean and the charging pin
is inserted correctly. Refer to “Charging the Battery” Section on
page 15 and “Charger LED Indicator” Section on page 17.
Cannot activate VOX
VOX feature might be OFF.
Use the CPS to ensure that the VOX Sensitivity Level is not set
to “0”.
Accessory not working or not compatible.
Battery doesn't charge although it Check drop-in charger is connected and correspond to a
has been placed in the drop-in
compatible power supply.
charger for a while
Refer to “Charging the Battery” Section on page 15.
Check the charger LEDs indicators to see if battery has a
problem. Refer to “Charger LED Indicator” Section on page 17.
34
Try this
Unable to pair a Bluetooth
headset
Make sure the target Bluetooth headset is not connected to
another device.
Unable to connect to a Bluetooth
headset
Make sure the target Bluetooth headset is not connected to
another device.
Pairing with wrong Bluetooth
headset
Don’t perform pairing procedures next to other Bluetooth
headset devices.
CLP Bluetooth uses proximity pairing. Make sure the headset is
placed next to the CLP radio.
Note:
Whenever a feature in your radio seems to not correspond to the default or preprogrammed values,
check if your radio have been programmed using CPS with a customized profile.
35
TROUBLESHOOTING
Symptom
USE AND CARE
USE AND CARE
Use a soft damp cloth
to clean the exterior.
Do not immerse in water.
Do not use alcohol or
cleaning solutions.
If the portable is submerged in water...
Turn OFF and
remove batteries.
36
Dry with soft cloth.
Do not use until
completely dry.
RADIO FREQUENCY AND CODE CHARTS
These charts provide frequency information and are useful when using Motorola CLP Series TwoWay Radios with other business radios. Most of the frequency positions are the same as Spirit M,
GT, S, XTN, RDX and CLS Series frequency positions (where applicable), the bandwidths are
different.
CLP UHF Frequencies
Band
width
(kHz)
Freq.
Frequency
(MHz)
Band
width
(kHz)
Freq.
464.5000
12.5
13
461.1375
12.5
464.5500
12.5
14
461.1625
12.5
467.7625
12.5
15
461.1875
467.8125
12.5
16
467.8500
12.5
467.8750
Band
width
(kHz)
Frequenc
y (MHz)
Band
width
(kHz)
Freq.
25
462.8125
12.5
37
466.1125
12.5
26
462.8375
12.5
38
466.1375
12.5
12.5
27
462.8625
12.5
39
466.1625
12.5
461. 2125
12.5
28
462.8875
12.5
40
466.1875
12.5
17
461.2375
12.5
29
462.9125
12.5
41
466.2125
12.5
12.5
18
461.2625
12.5
30
464.4875
12.5
42
466.2375
12.5
467.9000
12.5
19
461.2875
12.5
31
464.8375
12.5
43
466.2625
12.5
467.9250
12.5
20
461.3125
12.5
32
464.5375
12.5
44
466.2825
12.5
461.0375
12.5
21
461.3175
12.5
33
464.5625
12.5
45
466.3125
12.5
10
461.0625
12.5
22
461.3625
12.5
34
466.0375
12.5
46
466.3375
12.5
11
461.0875
12.5
23
462.7625
12.5
35
466.0625
12.5
47
466.3625
12.5
12
461.1125
12.5
24
462.7875
12.5
36
466.0875
12.5
48
467.7875
12.5
Frequenc
y (MHz)
37
RADIO FREQUENCY AND
CODE CHARTS
Frequency
(MHz)
Freq.
CLP UHF Frequencies
Frequency
(MHz)
Band
width
(kHz)
Freq.
Frequency
(MHz)
Band
width
(kHz)
Freq.
49
467.8375
12.5
60
462.5125
12.5
50
467.8625
12.5
61
467.1875
12.5
51
467.8875
12.5
62
467.4625
52
467.9125
12.5
63
53
469.4875
12.5
54
469.5125
55
RADIO FREQUENCY AND
CODE CHARTS
Band
width
(kHz)
Frequenc
y (MHz)
Band
width
(kHz)
Freq.
71
451.6375
12.5
81
468.2125
12.5
72
452.3125
12.5
82
468.2625
12.5
12.5
73
452.5375
12.5
83
468.3125
12.5
467.4875
12.5
74
452.4125
12.5
84
468.3625
12.5
64
467.5125
12.5
75
452.5125
12.5
85
468.4125
12.5
12.5
65
451.1875
12.5
76
452.7625
12.5
86
468.4625
12.5
469.5375
12.5
66
451.2375
12.5
77
452.8265
12.5
87
468.5125
12.5
56
469.5625
12.5
67
451.2875
12.5
78
456.1875
12.5
88
468.5625
12.5
57
462.1875
12.5
68
451.3375
12.5
79
456.2375
12.5
89
468.6125
12.5
58
462.4625
12.5
69
451.4375
12.5
80
456.2875
12.5
90
468.6625
12.5
59
462.4875
12.5
70
451.5375
12.5
Freq.
38
Frequenc
y (MHz)
CTCSS/DPL Interference Eliminator Codes
Code
CTCSS/DPL
Code
DPL
Code
DPL
Code
DPL
Code
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Disabled
67
71.9
74.4
77
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100
103.5
107.2
110.9
114.8
118.8
123
127.3
131.8
136.5
141.3
146.2
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
122
39
40
41
42
43
44
45
46
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
69.3
23
25
26
31
32
43
47
51
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
54
65
71
72
73
74
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
243
244
245
251
261
263
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
445
464
465
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
39
RADIO FREQUENCY AND
CODE CHARTS
CTCSS
CTCSS/DPL Interference Eliminator Codes (cont’d)
DPL
Code
DPL
Code
DPL
Code
DPL
Code
120
743
146
Inverted DPL 55
171
Inverted DPL 80
195
Inverted DPL 104
RADIO FREQUENCY AND
CODE CHARTS
121
754
147
Inverted DPL 56
172
Inverted DPL 81
196
Inverted DPL 105
123
645
148
Inverted DPL 57
173
Inverted DPL 82
197
Inverted DPL 106
124
Customized PL
149
Inverted DPL 58
174
Inverted DPL 83
198
Inverted DPL 107
125
Customized PL
150
Inverted DPL 59
175
Inverted DPL 84
199
Inverted DPL 108
126
Customized PL
151
Inverted DPL 60
176
Inverted DPL 85
200
Inverted DPL 109
127
Customized PL
152
Inverted DPL 61
177
Inverted DPL 86
201
Inverted DPL 110
128
Customized PL
153
Inverted DPL 62
178
Inverted DPL 87
202
Inverted DPL 111
129
Customized PL
154
Inverted DPL 63
179
Inverted DPL 88
203
Inverted DPL 112
130
Inverted DPL 39
155
Inverted DPL 64
180
Inverted DPL 89
204
Inverted DPL 113
131
Inverted DPL 40
156
Inverted DPL 65
181
Inverted DPL 90
205
Inverted DPL 114
132
Inverted DPL 41
157
Inverted DPL 66
181
Inverted DPL 90
206
Inverted DPL 115
133
Inverted DPL 42
158
Inverted DPL 67
182
Inverted DPL 91
207
Inverted DPL 116
134
Inverted DPL 43
159
Inverted DPL 68
183
Inverted DPL 92
208
Inverted DPL 117
135
Inverted DPL 44
160
Inverted DPL 69
184
Inverted DPL 93
209
Inverted DPL 118
136
Inverted DPL 45
161
Inverted DPL 70
185
Inverted DPL 94
210
Inverted DPL 119
137
Inverted DPL 46
162
Inverted DPL 71
186
Inverted DPL 95
211
Inverted DPL 120
138
Inverted DPL 47
163
Inverted DPL 72
187
Inverted DPL 96
212
Inverted DPL 121
139
Inverted DPL 48
164
Inverted DPL 73
188
Inverted DPL 97
213
Inverted DPL 123
140
Inverted DPL 49
165
Inverted DPL 74
189
Inverted DPL 98
214
Customized DPL
141
Inverted DPL 50
166
Inverted DPL 75
190
Inverted DPL 99
215
Customized DPL
142
Inverted DPL 51
167
Inverted DPL 76
191
Inverted DPL 100
216
Customized DPL
143
Inverted DPL 52
168
Inverted DPL 77
192
Inverted DPL 101
217
Customized DPL
144
Inverted DPL 53
169
Inverted DPL 78
193
Inverted DPL 102
218
Customized DPL
145
Inverted DPL 54
170
Inverted DPL 79
194
Inverted DPL 103
219
Customized DPL
40
What Does this Warranty Cover?
Subject to the exclusions contained below,
Motorola, Inc. warrants its telephones, pagers, and
consumer and business two-way radios (excluding
commercial, government or industrial radios) that
operate via Family Radio Service or General
Mobile Radio Service, Motorola-branded or
certified accessories sold for use with these
Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media
and sold for use with these Products (“Software”)
to be free from defects in materials and
workmanship under normal consumer usage for
the period(s) outlined below.
This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola
Products, Accessories and Software purchased by
consumers in the United States and Canada,
which are accompanied by this written warranty.
Products and Accessories
Products Covered
Length of Coverage
Products and
Accessories as
defined above, unless
otherwise provided for
below.
One (1) year from the date
of purchase by the first
consumer purchaser of the
product unless otherwise
provided for below.
Decorative
Accessories and
Cases.
Decorative covers,
bezels, PhoneWrap™
covers and cases.
Limited lifetime warranty
for the lifetime of
ownership by the first
consumer purchaser of the
product.
Business Two-way
Radio Accessories
One (1) year from the date
of purchase by the first
consumer purchaser of the
product.
Products and
Accessories that are
Repaired or
Replaced.
The balance of the
original warranty or for
ninety (90) days from the
date returned to the
consumer, whichever is
longer.
41
WARRANTY
MOTOROLA LIMITED
WARRANTY FOR THE
UNITED STATES AND
CANADA
WARRANTY
Exclusions
Normal Wear and Tear. Periodic maintenance,
repair and replacement of parts due to normal
wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged
capacity falls below 80 % of their rated capacity
and batteries that leak are covered by this limited
warranty.
Abuse & Misuse. Defects or damage that result
from: (a) improper operation, storage, misuse or
abuse, accident or neglect, such as physical
damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with
liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (d)
other acts which are not the fault of Motorola, are
excluded from coverage.
42
Use of Non-Motorola Products and
Accessories. Defects or damage that result from
the use of Non-Motorola branded or certified
Products, Accessories, Software or other
peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects
or damages resulting from service, testing,
adjustment, installation, maintenance, alteration,
or modification in any way by someone other than
Motorola, or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with
(a) serial numbers or date tags that have been
removed, altered or obliterated; (b) broken seals
or that show evidence of tampering; (c)
mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or
parts, are excluded form coverage.
Software. Applies only
to physical defects in
the media that
embodies the copy of
the software (e.g. CDROM, or floppy disk).
WHO IS COVERED?
This warranty extends only to the first consumer
purchaser, and is not transferable.
Software
Products Covered
Software NOT Embodied in Physical Media.
Software that is not embodied in physical media
(e.g. software that is downloaded from the
internet), is provided “as is” and without warranty.
Length of Coverage
Ninety (90) days from the
date of purchase.
Exclusions
Software Embodied in Physical Media. No
warranty is made that the software will meet your
requirements or will work in combination with any
hardware or software applications provided by
third parties, that the operation of the software
products will be uninterrupted or error free, or that
all defects in the software products will be
corrected.
WHAT WE WILL DO TO CORRECT
WARRANTY PROBLEMS
At no charge to you, we have the option to repair
or replace the Products or software that do not
conform to the warranty, or to refund the Products’
purchase price. We may use functionally
equivalent reconditioned/refurbished/pre-owned or
new Products or parts. No software updates are
provided.
HOW TO OBTAIN WARRANTY SERVICE OR
OTHER INFORMATION?
Contact your Motorola point of purchase.
Please call:
1-800-448- 6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
43
WARRANTY
Communication Services. Defects, damages, or
the failure of Products, Accessories or Software
due to any communication service or signal you
may subscribe to or use with the Products
Accessories or Software is excluded from
coverage.
WARRANTY
You will receive instructions on how to ship the
Products to Motorola. You must ship the Products
to us with freight, duties and insurance prepaid.
Along with the Products you must include:
(a) a copy of your receipt, bill of sale or other
comparable proof of purchase;
(b) a written description of the problem;
(c) the name of your service provider (if this
Product requires subscription service);
(d) the name and location of the installation facility
(if applicable) and, most importantly;
(e) your address and telephone number. If
requested, you must also return all detachable
parts such as antennas, batteries and chargers.
RETAIN YOUR ORIGINAL PROOF OF
PURCHASE
We will ship repaired or replacement Products at
our expense for the freight and insurance, but at
your expense for any duties. If additional
information is needed, please contact us at the
telephone number listed above.
44
SOFTWARE COPYRIGHT NOTICE
The Motorola products described in this manual
may include copyrighted Motorola and third party
software stored in semiconductor memories or
other media. Laws in the United States and other
countries preserve for Motorola and third party
software providers certain exclusive rights for
copyrighted software, such as the exclusive rights
to distribute or reproduce the copyrighted
software. Accordingly, any copyrighted software
contained in the Motorola products may not be
modified, reverse-engineered, distributed, or
reproduced in any manner to the extent allowed by
law.
Furthermore, the purchase of the Motorola
products shall not be deemed to grant either
directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or
patent applications of Motorola or any third party
software provider, except for the normal, nonexclusive, royalty-free license to use that arises by
operation of law in the sale of a product.
EXPORT LAW ASSURANCES
This product is covered by one or more of the
following United States patents.
5896277 5894292 5864752 5699006 5742484
D408396 D399821 D387758 D389158 5894592
5893027 5789098 5734975 5861850 D395882
D383745 D389827 D389139 5929825 5926514
5953640 6071640 D413022 D416252 D416893
D433001
This product is controlled under the export
regulations of the United States of America. The
Governments of the United States of America may
restrict the exportation or re-exportation of this
product to certain destinations. For further
information contact the U.S. Department of
Commerce.
45
WARRANTY
PATENT NOTICE
ACCESSORIES
AUDIO ACCESSORIES
ACCESSORIES
Part No.
Part No.
CLP Series Single Pin
Adjustable Cord Earpiece
HKLN4436_
CLP Series Single Pin
Adjustable Inline PTT Earpiece
HKLN4437_
CLP Single Pin Short Cord
Earpiece
HKLN4455_
CLP Single Pin Non-Adjustable
PTT Earpiece
Description
HKNN4013_
CLP Series High Capacity
Li-Ion Battery Kit
HKNN4014_
CLP Series Standard Li-Ion
Battery Kit
HKLN4440_
CLP High Capacity Li-Ion
Battery Door Kit
HKLN4441_
CLP Standard Li-Ion Battery
Door Kit
Description
HKLN4435_
46
BATTERIES
CARRY ACCESSORIES
Part No.
Description
HKLN4433_
CLP Series Magnetic Case (*)
HKLN4438_
CLP Series Swivel Belt Clip
Holster
CHARGERS
Part No.
Description
HKPN4007_
CLP Series Multi Unit Charger
(MUC) Kit
HKPN4008_
CLP Series Single Unit Charger
(SUC) Kit
PROGRAMMING CABLES
Description
HKKN4025_
CLP Series CPS Cable Kit
HKKN4026_
CLP Series Cloning Cable Kit
RLN6303_
RDX Serial Clone Cable
Note:
ACCESSORIES
Part No.
(*) Certain accessories may be or may not be
available at the time of purchase. For latest
information on accessories, contact your Motorola
point of purchase or visit: www.motorola.com/CLP
For product-related questions, contact:
1-800-448- 6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
47
ACCESSORIES
Notes
48
M
Motorola Inc.
1301 E. Algonquin Rd.
Schaumburg, IL 60196-1078 U.S.A.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.
All other product or service names are the property of their respective owners.
© 2010 by Motorola, Inc.
All rights reserved.
Printed in Malaysia.
*68012000044*
68012000044-C

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2010:12:27 14:04:56-05:00
Create Date                     : 2010:11:16 09:07:48Z
Metadata Date                   : 2010:12:27 14:04:56-05:00
Format                          : application/pdf
Title                           : 2000044-C_CLP_en.book
Creator                         : MHDW87
Document ID                     : uuid:c242b5de-d300-47b5-b20b-81bd37a2a344
Instance ID                     : uuid:4c30d405-1d6e-4a2d-bd6a-2c8045548b1d
Page Count                      : 58
Author                          : MHDW87
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ489FT4900

Navigation menu