Motorola Solutions 89FT7059 Portable 2-way radio User Manual APX 7000 7000L Portable Dual Display User Guide
Motorola Solutions, Inc. Portable 2-way radio APX 7000 7000L Portable Dual Display User Guide
Contents
- 1. Safety Manual
- 2. User Manual
User Manual
6875945M01-M Dual Display APX 7000/APX 7000L User Guide 4-Way Navigation Button Data Feature Button Menu Select Buttons Secondary Speaker 2-Position Concentric Switch __________ 3-Position A/B/C Switch __________ Battery Main Speaker Bluetooth Pairing Indicator Top Display Antenna • Channel – Channel switch to desired channel. English 68007024034-G *68007024034* To exit emergency at any time, press and hold the Emergency button. • Zone – Zone switch to desired zone. Zones and Channels * Default emergency button press timer is set to 1 second. This timer is programmable, see page 68 in the user guide for details. four beeps; alarm ends; and radio exits emergency. 3 When acknowledgment is received, you hear current zone/channel. Radio sounds a short, medium-pitched tone, and the LED blinks red momentarily. 2 The display shows Emergency and the 1 Press and hold the Emergency button*. Sending an Emergency Alarm receive. 4 Press the PTT button to transmit; release to 3 Adjust volume, if necessary. OR Press and hold Volume Set button. OR Press Monitor button and listen for activity. 2 Listen for a transmission. 1 Select zone/channel. Receiving and Transmitting • Off – On/Off/Volume knob counterclockwise. • On – On/Off/Volume knob clockwise. Radio On/Off Side Button 2 __________ Side Button 1 __________ PTT Button Top Side (Select) Button __________ On/Off/Volume Control Knob 16-Position Select Knob __________ MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2009–20142014 by Motorola Solutions, Inc. All Rights Reserved. 05/14 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. Keypad Home Button Main Display Accessory Connector Microphone Top (Orange) Button __________ Radio Controls ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios ASTRO® APX™ 7000/APX 7000L Series Digital Portable Radios Quick Reference Card Transmitting a call or data. Receiving a call or data. English Display Status Icons To exit emergency at any time, press and hold the Emergency button. Press and hold the Emergency button to exit emergency state. OR Press and release the PTT button to exit the Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode. 3 Silent emergency continues until you: not light up, and there is no tone. 2 The display does not change; the LED does 1 Press the Emergency button. Sending a Silent Emergency Call To exit emergency at any time, press and hold the Emergency button. emergency. 4 Press and hold Emergency button to exit 3 Release the PTT button to end call. into the microphone. 2 Press and hold the PTT button. Speak clearly 1 Press the Emergency button. Sending an Emergency Call Direct radio to radio communication or connected through a repeater. On = Direct Off = Repeater The more stripes, the stronger the signal strength for the current site (trunking only). Blinks when the battery is low. < or > to Menu Entry. Menu Navigation The vote scan feature is enabled. H to exit. Entry to select. {, |, or } directly below Menu Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. M This channel is being monitored. is set at Low power. H . LH == Radio Radio is set at High power. i Scanning a scan list. OR U or D to scroll through sub-list. Bluetooth is connected to the device. Bluetooth is ready. Data activity is present. Entry to select. {, |, or } directly below Menu On = feature enabled, and signal available. Off = feature disabled. Blinking = feature enabled, but signal unavailable. On = User is currently associated with the radio. Off = User is currently not associated with the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. 2. This device must accept any interference received, including interference that may cause undesired operation. 1. This device may not cause harmful interference, and As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Class B Digital Device FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) conforms to the following regulations: Model Name: APX 7000/APX 7000L Hereby declares that the product: Address: 1303, East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. Phone Number: 1-800-927-2744 Responsible Party Name: Motorola Solutions, Inc. Per FCC CFR 47 Part 2 Section 2.1077(a) DECLARATION OF CONFORMITY This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Declaration of Conformity English Declaration of Conformity English ii Declaration of Conformity • Consult the dealer or an experienced radio/TV technician for help. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Increase the separation between the equipment and receiver. • Reorient or relocate the receiving antenna. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. See Part 15.105b These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for equipment compliance should note that the limits specified in this part will not prevent harmful interference under all circumstances. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Part. 15.19(3). FCC, to operate this device and should not be made. See 47 CFR Part 15.21. Information to the user. The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the Conforms to the following regulations: FCC Part 15, Section 15.19, 15.21, and 15.105 IC: 109U-89FT6000 & 109U-89FT7059 FCC ID: AZ489FT6000 & AZ489FT7059 Description: APX 7000/APX 7000L Bluetooth Option Board Model Name: MNUK6000 & APX7000L The following FCC information applies to Bluetooth radio options Additional FCC Note to Users English iii Declaration of Conformity English iv Declaration of Conformity If customers have already purchased the radio with the Bluetooth Option Board as part of the tanapa and they need to replace (repair) the option board, they can send the radio to any Motorola FM audited . approved, please send the radios back to the service center in order to keep the certification. Note: If the APX 7000 customers are purchasing the Bluetooth Option Board for the first time and their radios are FM This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210. This product also complies with CAN ICES-3 (B) / NMB-3(B). Industry Canada (IC) Statements: • Consult the dealer or an experienced radio/TV technician for help. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Increase the separation between the equipment and receiver. • Reorient or relocate the receiving antenna. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Computer Software Copyrights . . . . . . . . . . xvii Avis aux utilisateurs (FCC et Industrie Canada) . . .xvi Version du logiciel . . . . . . . . . . . . . . . . . . . . . .xvi Exposition aux radiofréquences et sécurité du produit pour radios bidirectionnelles portatives . . . xv Informations importantes sur la sécurité . . . xv Notice to Users (FCC and Industry Canada) . . . . .xiv Software Version . . . . . . . . . . . . . . . . . . . . . . .xiv RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios . . . . . . . . . . . . . . . . . . . xiii Important Safety Information . . . . . . . . . . . . .xiii Declaration of Conformity . . . . . . . . . . . . . . . . . .i This User Guide contains all the information you need to use the APX™ 7000/APX 7000L Series Digital Portable Radios. Contents English Using the Carry Holder . . . . . . . . . . . . . . . . . . . . . . . 6 Attaching the Accessory Connector Cover . . . . . . . . 6 Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 5 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 4 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 4 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparing Your Radio for Use . . . . . . . . . . . . . .3 What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Additional Performance Enhancement . . . . . . . . . . . 2 ASTRO 25 Enhanced Data . . . . . . . . . . . . . . . . . . . 2 Dynamic System Resilience (DSR) . . . . . . . . . . . . . 2 CrossTalk Prevention . . . . . . . . . . . . . . . . . . . . . . . 2 Encrypted Integrated Data (EID) . . . . . . . . . . . . . . . 2 SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Notations Used in This Manual . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . .1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii Documentation Copyrights . . . . . . . . . . . . . .xvii Contents Text Messaging Service (TMS) Icons . . . . . . . . . . 25 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Identifying Status Indicators . . . . . . . . . . . . . .19 Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . 19 Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Keypad Characters – Uppercase Mode . . . . . . . . . 15 Keypad Characters – Lowercase Mode . . . . . . . . . 16 Keypad Characters – Numeric Mode . . . . . . . . . . . 17 Keypad Characters – Hexadecimal Mode . . . . . . . 18 Home Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Data Feature Button . . . . . . . . . . . . . . . . . . . . . . . 14 4-Way Navigation Button . . . . . . . . . . . . . . . . . . . . 14 Accessing the Preprogrammed Functions . . . . . . . 14 Using the Menu Select Buttons . . . . . . . . . . . . . . . 14 Using the Navigation Buttons . . . . . . . . . . . . . . . . . 14 Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 43 Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . .43 Receiving and Responding to a Radio Call . . . . . . 40 Receiving and Responding to a Talkgroup Call . . .41 Receiving and Responding to a Private Call (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Receiving and Responding to a Telephone Call (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Using Mode Select Feature . . . . . . . . . . . . . . . . . . 39 Saving a Zone and Channel to a Softkey . . . . . . . .39 Saving a Zone and Channel to a Keypad Button . .40 Using Channel Search Button . . . . . . . . . . . . . . . . 38 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 36 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . 35 General Radio Operation . . . . . . . . . . . . . . . . 35 Phone Call Display and Alert Prompts . . . . . . . . . . 34 Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . 29 Programmable Features . . . . . . . . . . . . . . . . . . . . . 11 Assignable Radio Functions . . . . . . . . . . . . . . . . . . 11 Assignable Settings or Utility Functions . . . . . . . . . 13 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Call Type Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . . . .26 . . . . . . . . . . . . . . . . . . 10 Radio Parts and Controls Identifying Radio Controls . . . . . . . . . . . . . . . . .9 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 8 Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 7 English vi Contents Entering the Dynamic Zone to Select a Dynamic Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Saving a Channel in the Dynamic Zone from List Using Dynamic Zone Programming (DZP) . . . . . . .52 Requesting a Reprogram (Trunking Only) . . . . . . . 52 Classifying Regrouped Radios . . . . . . . . . . . . . . . . 52 Sending a Status Call . . . . . . . . . . . . . . . . . . . . . . .50 Using the Dynamic Regrouping Feature (Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Selecting a Talkgroup . . . . . . . . . . . . . . . . . . . . . . 50 Using the Talkgroup Call Feature (Conventional Operation Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Receiving a Selective Call . . . . . . . . . . . . . . . . . . . 49 Making a Selective Call . . . . . . . . . . . . . . . . . . . . . 49 Advanced Call Features . . . . . . . . . . . . . . . . . . . . . 49 Receiving and Making a Selective Call (ASTRO Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . . .49 Advanced Features . . . . . . . . . . . . . . . . . . . . . 48 Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 46 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . .46 Conventional Mode Operation . . . . . . . . . . . . . . . .47 Repeater or Direct Operation . . . . . . . . . . . . . . . . . 46 Making a Private Call (Trunking Only) . . . . . . . . . .43 Making an Enhanced Private Call (Trunking Only) .44 Making a Telephone Call (Trunking Only) . . . . . . . .45 vii English Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Turning Scan On or Off . . . . . . . . . . . . . . . . . . . . . 64 Making a Dynamic Priority Change (Conventional Scan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Deleting a Nuisance Channel . . . . . . . . . . . . . . . . 64 Restoring a Nuisance Channel . . . . . . . . . . . . . . . 65 Changing the Scan List Status . . . . . . . . . . . . . . . 63 Viewing and Changing the Priority Status . . . . . . 63 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . 61 Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . 62 Viewing Details of a Contact . . . . . . . . . . . . . . . . . 61 Editing an Entry Alias . . . . . . . . . . . . . . . . . . . . . . 59 Editing as Entry ID . . . . . . . . . . . . . . . . . . . . . . . . 60 Editing a Call Type . . . . . . . . . . . . . . . . . . . . . . . . 60 Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Making a Private Call from Contacts . . . . . . . . . . . 55 Adding a New Contact Entry . . . . . . . . . . . . . . . . . 56 Deleting a Contact Entry . . . . . . . . . . . . . . . . . . . . 58 Adding a Contact to a Call List . . . . . . . . . . . . . . . 58 Removing a Contact from a Call List . . . . . . . . . . . 59 Editing a Contact in a Call List . . . . . . . . . . . . . . . . 59 Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Saving a Channel in the Dynamic Zone from Channel Name . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Deleting a Channel in the Dynamic Zone . . . . . . . 54 Contents Man Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Pre-Alert Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Post-Alert Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Alerting User When Man Down Feature is Triggered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Triggering Emergency . . . . . . . . . . . . . . . . . . . . . . 76 Alerting User When Man Down Enhanced is Triggered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Exiting Man Down Feature . . . . . . . . . . . . . . . . . . . 77 Tactical Public Safety (TPS) (Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Using TPS Normal Transmission . . . . . . . . . . . . . . 73 Fireground (Conventional Only) . . . . . . . . . . . . . . . 71 Entering Fireground Zone Channel . . . . . . . . . . . . 71 Responding to Evacuation Indicator . . . . . . . . . . . . 72 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 67 Sending an Emergency Alarm . . . . . . . . . . . . . . . . 68 Sending an Emergency Call (Trunking Only) . . . . . 69 Sending an Emergency Alarm with Emergency Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Sending a Silent Emergency Alarm . . . . . . . . . . . . 70 Changing Channels during Emergncy . . . . . . . . . . 70 Using the Emergency Keep-Alive Feature . . . . . . . 70 Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Receiving a Call Alert Page . . . . . . . . . . . . . . . . . . 65 Sending a Call Alert Page . . . . . . . . . . . . . . . . . . . 66 English viii Contents Managing Sent Text Messages . . . . . . . . . . . . . . . .89 Receiving a Text Message . . . . . . . . . . . . . . . . . . .87 Viewing a Text Message from the Inbox . . . . . . . .87 Replying to a Received Text Message . . . . . . . . . .88 Accessing the Drafts Folder . . . . . . . . . . . . . . . . . .89 Managing Text Messages . . . . . . . . . . . . . . . . . . . .87 Appending a Priority Status to a Text Message . . .85 Removing a Priority Status from a Text Message .85 Appending a Request Reply to a Text Message . .85 Removing a Request Reply from a Text Message .86 Appending a Priority Status and a Reply Request to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . .86 Removing a Priority Status and a Reply Request from a Text Message . . . . . . . . . . . . . . . . . . . . . . .86 Text Messaging Service (TMS) . . . . . . . . . . . . . . . 81 Accessing the Messaging Features . . . . . . . . . . . .81 Composing and Sending a New Text Message . . .82 Sending a Quick Text Message . . . . . . . . . . . . . . .83 Using the Priority Status and Request Reply Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Logging In as a User . . . . . . . . . . . . . . . . . . . . . . .79 Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Automatic Registration Service (ARS) . . . . . . . . . . 78 Selecting or Changing the ARS Mode . . . . . . . . . .78 Accessing the User Login Feature . . . . . . . . . . . . .79 Re-Initiating Man Down . . . . . . . . . . . . . . . . . . . . . .77 Testing the Man Down Feature . . . . . . . . . . . . . . . .77 105 103 103 104 The Global Positioning System (GPS) . . . . . . . . . 107 Understanding the GPS Feature . . . . . . . . . . . . . 107 Enhancing GPS Performance . . . . . . . . . . . . . . . 108 The Outdoor Location Feature (Using GPS) . . . . 108 Enabling MGRS Coordinates . . . . . . . . . . . . . . . . 109 Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . 97 Selecting Secure Transmissions . . . . . . . . . . . . . . .97 Selecting Clear Transmissions . . . . . . . . . . . . . . . .98 Managing Encryption . . . . . . . . . . . . . . . . . . . . . . .98 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 ix English Accessing the Outdoor Location Feature . . . . . . 109 Saving a Waypoint . . . . . . . . . . . . . . . . . . . . . . . 110 Viewing a Saved Waypoint . . . . . . . . . . . . . . . . . 111 Editing the Alias of a Waypoint . . . . . . . . . . . . . . 112 Editing the Coordinates of a Waypoint . . . . . . . . 112 Deleting a Single Saved Waypoint . . . . . . . . . . . 113 Deleting All Saved Waypoints . . . . . . . . . . . . . . . 114 Measuring the Distance and Bearing from a Saved Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Using the Location Feature While in Emergency Using Remote Kill . . . . . . . . . . . . . . . . . . . . . . . . 106 Using Direct Kill . . . . . . . . . . . . . . . . . . . . . . . . . 107 Sending a Query . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Receiving a Query . . . . . . . . . . . . . . . . . . . . . . . . . .97 Loading an Encryption Key . . . . . . . . . . . . . . . . . . 98 Using the Multikey Feature . . . . . . . . . . . . . . . . . . 99 Selecting an Encryption Key . . . . . . . . . . . . . . . . . 99 Selecting a Keyset . . . . . . . . . . . . . . . . . . . . . . . . 100 Erasing the Selected Encryption Keys . . . . . . . . . 100 Requesting an Over-the-Air Rekey (ASTRO Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . 101 MDC Over-the-Air Rekeying (OTAR) Page . . . . . 102 Infinite UKEK Retention . . . . . . . . . . . . . . . . . . . . 102 Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Using Radio Kill . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Using Radio Stun . . . . . . . . . . . . . . . . . . . . . . . . 105 Radio Stun and Kill . . . . . . . . . . . . . . . . . . . . . . . . 105 Using Radio Stun . . . . . . . . . . . . . . . . . . . . . . . . . 105 Unlocking Your Radio . . . . . . . . . . . . . . . . . . . . . Changing Your Password . . . . . . . . . . . . . . . . . . Changing Your Tactical Inhibit Password . . . . . . Enabling or Disabling the Radio Lock Feature (Secure Radios Only) . . . . . . . . . . . . . . . . . . . . . Radio Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Logging into Two-Factor Authentication . . . . . . . . . 93 Logging out of Two-Factor Authentication . . . . . . . 95 ASTRO 25 Advanced Messaging Solution . . . . . . . 92 System Setup for ASTRO Advanced Messaging Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Two-Factor Authentication . . . . . . . . . . . . . . . . . . .93 Viewing a Sent Text Message . . . . . . . . . . . . . . . . 89 Sending a Sent Text Message . . . . . . . . . . . . . . . . 90 Deleting a Text Message . . . . . . . . . . . . . . . . . . . . 91 Deleting All Text Messages . . . . . . . . . . . . . . . . . . 91 Contents Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Comparing Authentication PIN When Receiving a Pairing Request . . . . . . . . . . . . . . . . . . . . . . . . 125 Comparing Authentication PIN with Generated Numeric PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Pairing with PIN Authentication . . . . . . . . . . . . . . 125 Searching and Pairing the Bluetooth Device . . . . 123 Turning Bluetooth Visibility On . . . . . . . . . . . . . . . 124 Receiving Pairing Request from other Devices . . 124 Turning Bluetooth Visibility Off . . . . . . . . . . . . . . . 125 Mission Critical Wireless (MCW) - Bluetooth® - . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Turning the Bluetooth On . . . . . . . . . . . . . . . . . . . 118 Turning the Bluetooth Off . . . . . . . . . . . . . . . . . . . 118 Re-Pair Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Bluetooth Drop Timer . . . . . . . . . . . . . . . . . . . . . . 120 Pairing with LF MPP Pairing Feature . . . . . . . . . . 120 Indicating Bluetooth Connection is Lost . . . . . . . . 122 Pairing with Standard Pairing Feature . . . . . . . . . 122 Viewing the Current Site . . . . . . . . . . . . . . . . . . . 117 Changing the Current Site . . . . . . . . . . . . . . . . . . 117 Trunking System Controls . . . . . . . . . . . . . . . . . . 115 Using the Failsoft System . . . . . . . . . . . . . . . . . . . 115 Going Out of Range . . . . . . . . . . . . . . . . . . . . . . . 116 Using the Site Trunking Feature . . . . . . . . . . . . . . 116 Locking and Unlocking a Site . . . . . . . . . . . . . . . . 116 Viewing and Changing a Site . . . . . . . . . . . . . . . . 117 English Contents Using Site Selectable Alerts (ASTRO 25) . . . . . . 134 Sending SSA Notification to Single Site . . . . . . . .134 Sending SSA Notification to Single Site Via Manual Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 Sending SSA Notification to All Sites . . . . . . . . . .136 Sending SSA Notification to All Available Sites . .137 Stopping SSA Notification of a Single Site . . . . . .137 Stopping SSA Notification of a Single Site Via Manual Entry . . . . . . . . . . . . . . . . . . . . . . . . . .138 Stopping SSA Notification of All Sites . . . . . . . . . .139 Voice Announcement . . . . . . . . . . . . . . . . . . . . . . 133 Programming Over Project 25 (POP 25) (ASTRO 25 and ASTRO Conventional) . . . . . . . 132 Responding to the notification of Upgrade . . . . . .133 Turning On the Bluetooth Audio (Routing the Audio from the Radio to the Headset) . . . . . . . . . .128 Turning Off the Bluetooth Audio (Routing the Audio from the Headset to the Radio) . . . . . . . . . .128 Adjusting the Volume of the Radio from Bluetooth Audio Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Viewing and Clearing the Bluetooth Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Editing the Bluetooth Friendly Name . . . . . . . . . . .131 Pairing with LEX 700 (APX 7000 Dual Display only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 Comparing Authentication PIN by Manually Keying in the Same PIN . . . . . . . . . . . . . . . . . . . .127 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Viewing the Recent Calls . . . . . . . . . . . . . . . . . . .145 Using the Flip Display . . . . . . . . . . . . . . . . . . . . . .146 Selecting a Basic Zone Bank . . . . . . . . . . . . . . . .146 Selecting an Enhanced Zone Bank . . . . . . . . . . . .147 Selecting the Power Level . . . . . . . . . . . . . . . . . . .147 Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . .148 Enabling and Disabling the Radio Alias . . . . . . . .148 Selecting the Audio Speaker . . . . . . . . . . . . . . . . .149 Controlling the Display Backlight . . . . . . . . . . . . . .149 Setting Up the Radio Display and Visual Indicators to Suite Night Vision Goggles . . . . . . . .150 Locking and Unlocking the Keypad and Controls .151 Turning Keypad Tones On or Off . . . . . . . . . . . . .152 Turning Voice Mute On or Off . . . . . . . . . . . . . . . .152 Using the Time-Out Timer . . . . . . . . . . . . . . . . . . .153 Long Term Evolution (LTE) (APX 7000L Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Data Profiles Available for LTE . . . . . . . . . . . . . . .141 Turning On the LTE at the LTE Menu Screen . . . .142 Turning On the LTE with LTE Button . . . . . . . . . .142 Turning Off the LTE Connection . . . . . . . . . . . . . .143 Information at the LTE Screen . . . . . . . . . . . . . . .143 Changing from LTE-enabled Channel to LTE-disabled Channel . . . . . . . . . . . . . . . . . . . . . .144 Changing from LTE-enabled Channel to Unprogrammed Channel . . . . . . . . . . . . . . . . . . . .144 Stopping SSA Notification of All Available Sites . .139 155 156 155 155 157 158 159 159 xi English Battery Recycling and Disposal . . . . . . . . . . . . . . 165 LED and Sounds . . . . . . . . . . . . . . . . . . . . . . . . . 164 Fuel Gauge Icon . . . . . . . . . . . . . . . . . . . . . . . . . 164 Taking Care of the Battery . . . . . . . . . . . . . . . . . . 164 Checking the Battery Charge Status . . . . . . . . . . 164 Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . 161 Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . 162 Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . 163 Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . 163 Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .161 Accessing the Radio Information . . . . . . . . . . . . Viewing the IP Information . . . . . . . . . . . . . . . . . Viewing the Control Assignments . . . . . . . . . . . . Editing the Soft ID . . . . . . . . . . . . . . . . . . . . . . . . Accessing the General Radio Information . . . . . . 157 Accessing the Battery Info screen . . . . . . . . . . . 156 Using the PL Defeat Feature . . . . . . . . . . . . . . . . Using the Digital PTT ID Feature . . . . . . . . . . . . . Using the Smart PTT Feature (Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . IMPRES™ Battery Annunciator . . . . . . . . . . . . . . Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Using the Conventional Squelch Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Editing the Time and Date . . . . . . . . . . . . . . . . . 153 Setting the Time and Date . . . . . . . . . . . . . . . . . . 153 Contents Commercial Warranty . . . . . . . . . . . . . . . . . . .176 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 Declaration of Compliance for the User of Distress and Safety Frequencies . . . . . . . . . . . . 170 Operating Frequency Requirements . . . . . . . . . . 168 Special Channel Assignments . . . . . . . . . . . . . . . 167 Emergency Channel . . . . . . . . . . . . . . . . . . . . . . . 167 Non-Commercial Call Channel . . . . . . . . . . . . . . . 167 Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . .167 Highlights for the Accessories . . . . . . . . . . . . . . . 166 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .166 English xii Contents Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power http://www.motorolasolutions.com/APX For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website: This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. ATTENTION! RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios Important Safety Information xiii English This radio transmitter has been approved by Industry Canada to operate with the Motorola-approved antenna types with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. (e.i.r.p.) is not more than that necessary for successful communication. Important Safety Information Check with your dealer or system administrator for more details of all the features supported. See Accessing the Radio Information on page 157 to determine your radio's software version. All the features described in the following sections are supported by the radio's software version R12.00.00 or later. Software Version English xiv Software Version expressly approved by Motorola, could void the user's authority to operate this equipment. 3 Changes or modifications made to this device, not including interference that may cause undesired operation. 2 This device must accept any interference received, 1 This device may not cause harmful interference. This device complies with Part 15 of the FCC rules and RSS 210 of the Industry Canada rules per the conditions listed below: Notice to Users (FCC and Industry Canada) Selon la règlementation d'Industrie Canada, cet émetteur radio ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada pour cet émetteur. Afin de limiter les interférences radio pour les http://www.motorolasolutions.com/APX Pour obtenir une liste d'antennes et d'autres accessoires approuvés par Motorola, consultez le site Web : Cette radio ne doit être utilisée qu'à des fins professionnelles. Avant d'utiliser la radio, lisez le guide Exposition aux radiofréquences et sécurité du produit pour radios bidirectionnelles portatives, qui contient d'importantes instructions de fonctionnement pour une utilisation sécuritaire et des informations sur l'exposition aux fréquences radioélectriques afin d'assurer la conformité aux normes et règlements applicables. ATTENTION! Exposition aux radiofréquences et sécurité du produit pour radios bidirectionnelles portatives Informations importantes sur la sécurité xv Français Canadien Le présent émetteur a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne agréés par Motorola et ayant un gain admissible maximal ainsi que l'impédance requise pour chaque type d'antenne indiqué. Les types d'antenne non inclus, dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. autres utilisateurs, le type et le gain de l'antenne doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) ne soit pas plus forte qu'il ne le faut pour établir la communication. Informations importantes sur la sécurité dispositif, non expressément approuvées par Motorola, peuvent annuler le droit de l'utilisateur à utiliser cet équipement. 3 Les changements ou les modifications apportées à ce compris les interférences qui peuvent perturber le fonctionnement. 2 Cet appareil doit accepter toute interférence reçue, y nuisibles. 1 Ce dispositif ne doit pas causer d'interférences Cet appareil est conforme à la Partie 15 des règlements de la FCC et RSS 210 du règlement d'Industrie Canada selon les conditions énumérées ci-dessous: Avis aux utilisateurs (FCC et Industrie Canada) Vérifiez auprès de votre détaillant ou de l'administrateur de système pour obtenir des renseignements sur les fonctionnalités prises en charge. Toutes les fonctionnalités décrites dans les sections suivantes sont prises en charge par la version du logiciel R12.00.00 ou ultérieure de la radio. Version du logiciel Français Canadien xvi Version du logiciel No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. xvii English Documentation Copyrights Computer Software Copyrights Computer Software Copyrights The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Disclaimer English xviii Disclaimer However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. This User Guide covers the basic operation of the APX™ 7000/ APX 7000L Portables. How to Use This Guide How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1 Additional Performance Enhancement . . . . . . . . . . . . . page 2 What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3 Take a moment to review the following: Getting Started Note: Caution WARNING English An operational procedure, practice, or condition, etc., which is essential to emphasize. An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed. Notations Used in This Manual Getting Started Description This means “Press the right side of the 4-way Navigation button”. Phone DSR seamlessly switches the radio system to a backup master site during system failures. DSR also provides additional Dynamic System Resilience (DSR) ASTRO 25 Enhanced Data is optimized to handle different message sizes and update rates from different applications. Install Enhanced Data to the Integrated Data system with a software installation to improve data channel efficiency and enable denser network traffic. ASTRO 25 Enhanced Data The following are some of the latest creations designed to enhance the security, quality and efficiency of the radios. Additional Performance Enhancement Menu entries are shown similar to the way they appear on the radio’s display. Home button Buttons and keys are shown in bold print or H or as an icon. Example The following special notations identify certain items: English Getting Started SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel. SecureNet EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network. Encrypted Integrated Data (EID) This feature prevents crosstalk scenarios from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be different from the Receiving Frequency. This subsequently reduces the possibilities of radio frequency interfering spurs and it also prevents crosstalk. CrossTalk Prevention indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR. • What optional accessories may suit your needs? features? • Which buttons have been preprogrammed to access other channels? • Is your radio preprogrammed with any preset conventional You can also consult your dealer or system administrator about the following: Check with your dealer or system administrator for the correct radio settings, if the radio is to be operated in extreme temperatures (less than -30 °C or more than +60 °C), to ensure proper top and front display operation. What Your Dealer/System Administrator Can Tell You English Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . page 5 Attaching the Accessory Connector Cover . . . . . . . . . . page 6 Using the Carry Holder. . . . . . . . . . . . . . . . . . . . . . . . . . page 6 Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8 Assemble your radio by following these steps: Preparing Your Radio for Use Preparing Your Radio for Use • DO NOT discard batteries in a fire. • DO NOT replace the battery in any area labeled “hazardous atmosphere”. When charging a battery attached to a radio, turn the radio off to ensure a full charge. For a list of chargers, see Accessories on page 166. To charge the battery, place the battery, with or without the radio, in a Motorola-approved charger. The charger’s LED indicates the charging progress; see your charger’s user guide. Battery Charger Note: For a list of Motorola-authorized batteries available for use with your radio, see Accessories on page 166. The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. WARNING To avoid a possible explosion: Charging the Battery English Preparing Your Radio for Use With the radio turned off, slide the battery into the radio’s frame until side latches click into place. Attaching the Battery You can view the status of the IMPRES™ battery if the radio is using an IMPRES battery. See IMPRES™ Battery Annunciator on page 156 for more information. Battery Latch Note:If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal. Check with your dealer or system administrator for more information. To remove the battery, turn the radio off. Squeeze the release latches at the bottom of the battery until the battery releases from the radio. Remove the battery from the radio. English To remove the antenna, turn the antenna counterclockwise. Make sure you turn off the radio first. With the radio turned off, set the antenna in its receptacle and turn clockwise to attach it to the radio. Attaching the Antenna Preparing Your Radio for Use Rotate and lift the connector cover to disengage it from the radio. To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio. If the thumbscrew is too tight, use an Allen wrench to loosen it first. Hex Socket Head Thumbscrew Hooked End To prevent damage to the connector, shield it with the connector cover when not in use. Insert the hooked end of the cover into the slot above the connector. Press downward on the cover’s top to seat it in the slot. Once in place, tighten by rotating the thumbscrew clockwise by hand. Note: The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio. Attaching the Accessory Connector Cover English Preparing Your Radio for Use Using the Carry Holder Position the radio within the carry holder with the main speaker facing outward. Slide the radio down into the carry holder until it clicks into place. To remove the radio from the carry holder, place the tip of your fingers on the ledge of the carry holder and push at the bottom of the radio until the radio is released from it. English If the power-up test is successful, you see momentary SELFTEST on the radio’s display, followed by the Home screen. Rotate the On/Off/Volume Control Knob clockwise until you hear a click. Turning On the Radio Preparing Your Radio for Use Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, record the Error XX/YY code and contact your dealer. If the power-up test is unsuccessful, you see Error XX/YY (XX/YY is an alphanumeric code). To turn off the radio, rotate the On/Off/Volume Control Knob counterclockwise until you hear a click. Note: English Preparing Your Radio for Use Note: Ensure that the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises. To decrease the volume, turn this knob counterclockwise. Main Speaker To increase the volume, turn the On/Off/Volume Control Knob clockwise. Adjusting the Volume Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . page 10 Programmable Features . . . . . . . . . . . . . . . . . . . . . . . page 11 Assignable Radio Functions . . . . . . . . . . . . . . . . . . page 11 Assignable Settings or Utility Functions. . . . . . . . . . page 13 Accessing the Preprogrammed Functions. . . . . . . . . . page 14 Using the Menu Select Buttons . . . . . . . . . . . . . . . . page 14 Using the Navigation Buttons. . . . . . . . . . . . . . . . . . page 14 Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15 Keypad Characters – Uppercase Mode. . . . . . . . . . page 15 Keypad Characters – Lowercase Mode. . . . . . . . . . page 16 Keypad Characters – Numeric Mode. . . . . . . . . . . . page 17 Keypad Characters – Hexadecimal Mode . . . . . . . . page 18 Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 19 Take a moment to review the following: Identifying Radio Controls English Identifying Radio Controls Button 7 Navigation 4-Way 6 Home Button 5 Connector Accessory 4 Microphone 3 Button* Top (Orange) 2 LED 1 Antenna Radio Parts and Controls English 10 Identifying Radio Controls On/Off/Volume Control Knob Data Feature 20 Side Button 2* 19 Side Button 1* Push-to-Talk 18 (PTT) Button Top Side (Select) 17 Button* 8 Battery Latch 9 Keypad 10 Button 11 Menu Select Buttons 12 Main Display 13 Secondary Speaker 2-Position Concentric 14 Switch* 16 3-Position A/B/C 15 Switch* * These radio controls/buttons are programmable. 21 Battery Main 22 Speaker 23 Microphone Indicator Bluetooth 24 Pairing 25 Display Top 16-Position 26 Select Knob* Bluetooth Headset PTT – Keys up the Bluetooth Headset's microphone. Bluetooth Audio Reroute – Allows you to toggle the audio route between radio speaker or Remote Speaker Microphone and Bluetooth headset. Bluetooth Configuration – Allows you to access to the Bluetooth menu. 11 English Internet Protocol Address – Displays the Internet Protocol (IP) address, device name and status of the radio. Information – Displays the information of the radio. Emergency – Depending on the programming, initiates or cancels an emergency alarm or call. Dynamic Priority (Conventional Only) – Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Dynamic ID (Conventional Only) – Allows you to edit the radio's ASTRO Individual ID and/or MDC Primary ID. Assignable Radio Functions Bluetooth On/Off – Allows you to turn on/off the Bluetooth. Contacts – Selects the Contacts menu. Channel – Selects a channel. Call Response – Allows you to answer a private call. Call Alert – Allows the radio to function like a pager, or to verify if a radio is active on the system. Bluetooth Discoverable On/Off – Enables Bluetooth visibility. This is accessed by a long press of the Bluetooth Inquiry On/Off Button. Bluetooth Inquiry On/Off – Enables Bluetooth Search feature. Bluetooth Clear All Pairing – Allows you to clear all pairing info for Bluetooth. This is accessed by a long press of the Bluetooth On/Off Button. Bluetooth Data Devices – Keys up the Bluetooth data devices. • Hold down – Keeping the button pressed. duration (between 0.25 seconds and 3.75 seconds). • Long press – Pressing and holding for the preprogrammed • Press – Pressing and releasing rapidly. The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press: Any reference in this manual to a control that is “preprogrammed” means that the control must be programmed by a dealer or qualified radio technician using the radio's programming software, in order to assign a feature to that control. Programmable Features Identifying Radio Controls One Touch 1 – 4 – Launches a specific feature with one single button-press. You can setup as many as four separately programmed buttons for four different features. Nuisance Delete – Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. Multiple Private Line (Conventional Only) – Selects the Multiple Private Line lists. Monitor (Conventional Only) – Monitors a selected channel for all radio traffic until function is disabled. Mode Select – Long-press programs a button with the radio's current zone and channels; then once programmed, the shortpress of that button jumps the radio to the programmed zone and channel. Message – Enters the current message list. Man Down Clear – Clears the alarm of Man Down mode which was triggered when your radio achieves or passes a tilt angle threshold or a combination of the angle threshold and a motion sensitivity level. LTE On/Off – Press this button to enter LTE screen; long-press this button to toggle LTE module on or off. Location – Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another location. Or, turns the GPS functionality on or off for all location. English 12 Identifying Radio Controls Secure Transmission Select (Conventional and Trunking) – Toggles the Secure Transmission On or Off when the Secure/ Scan – Toggles scan on or off. Request-To-Talk (Conventional Only) – Notifies the dispatcher you want to send a voice call. Reprogram Request (Trunking Only) – Notifies the dispatcher you want a new dynamic regrouping assignment. Repeater Access Button (RAB) (Conventional Only) – Allows to manually send a repeater access codeword. Rekey Request – Notifies the dispatcher you want a new encryption keys. Recent Calls – Allows for easy access to the list of calls recently received or made. Radio Profiles – Allows for easy access to a set of preprogrammed visual and audio settings of the radio. Query – Launches a list of predefined short text messages only after successfully logged in the Two-Factor Authentification. Private Line Defeat (Conventional Only) – Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Private Call (Trunking Only) – Allows a call from an individual radio to another individual radio. Phone – Allows you to make and receive calls similar to standard phone calls. Basic Zone Bank – Provides access from up to 6 zones by toggling between 2 banks of 3 zones, one group of 3 (A, B and C) to a second group of 3 zones (D, E and F). Zone Select – Allows selection from a list of zones. User – Automatically registers with the server. TMS Quick Text – Selects a predefined message. Text Messaging Service (TMS) – Selects the text messaging menu. Talkgroup (Conventional Only) – Allows a call from an individual radio to a group of radios. Talkaround/Direct (Conventional Only) – Toggles between using a repeater and communicating directly with another radio. Status – Sends data calls to the dispatcher about a predefined status. Site Lock/Unlock (Trunking Only) – Locks onto a specific site. Site Display/Search (Trunking Only) – Displays the current site ID and RSSI value; performs site search for AMSS (Automatic Multiple Site Select) or SmartZone operation. Selective Call (Conventional Only) – Calls an assigned radio. Clear Strapping fields is set to “Select” for the radio’s current channel, and when the radio is model/option capable. Volume Set Tone – Sets the volume set tone. Voice Mute – Toggles voice mute on or off. 13 English Voice Announcement – Audibly indicates the current feature mode, Zone or Channel the user has just assigned. Keypad and Controls Lock – Locks or unlocks the keypad, programmable buttons, switches and rotary knobs. Light/Flip – Press the button to toggle the display backlight on or off; press and hold the button to reverse the content of the top display. Assignable Settings or Utility Functions Enhanced Zone Bank – Provides access from up to 75 zones by toggling between 25 banks (A, B ... X or Y) of 3 zones. Identifying Radio Controls Home Button 4-Way Navigation Button Zone | Chan | MyId Data Feature Button Menu Select Buttons Use this button to scroll up, down, left or right. Press and release one of the button to scroll from one entry to the next one. Press and hold one of the button to have the radio toggles through the list automatically (release the button to stop). 4-Way Navigation Button • Press the Menu Select button ( | ) directly below Chan. Data Feature Button Some features do not require you to press H to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information. Use this button to access data-related features, such as the Text Messaging Service (TMS) feature screen. Check with your dealer or system administrator for the list of features activated in your radio. Note: For selected radio features, the H button is also used to save user-edited radio settings or information before returning you to the Home screen. The H button returns you to the Home (default) screen. In most cases, this is the current mode. Home Button Using the Navigation Buttons Your radio may be preprogrammed differently from the following example, but the steps for selecting a channel may appear as shown below: Note: The Menu Select buttons access the menu entries of features. Using the Menu Select Buttons • Use the Menu Select Buttons ({, |, and }). OR • A short or long press of the relevant programmable buttons. You can access various radio functions through one of the following ways: Accessing the Preprogrammed Functions English 14 Identifying Radio Controls P Toggle between mixed case mode, uppercase mode, and lowercase mode. Space Toggle between numeric and letter mode. 13 12 11 10 14 Number of Times Key is Pressed Key Keypad Characters – Uppercase Mode 15 16 17 “ 18 ‘ 19 20 15 English 21 You can use the 3 x 4 alphanumeric keypad to access your radio’s features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character. Using the Keypad Identifying Radio Controls p Toggle between mixed case mode, uppercase mode, and lowercase mode. Space Toggle between numeric and letter mode. 13 12 11 10 14 Number of Times Key is Pressed Key Keypad Characters – Lowercase Mode English 16 Identifying Radio Controls 15 16 17 “ 18 ‘ 19 20 21 4 Space Toggle between numeric and letter mode. Key Keypad Characters – Numeric Mode 10 11 12 13 14 Number of Times Key is Pressed 15 16 17 “ 18 ‘ 19 20 17 English 21 Identifying Radio Controls 3 Not applicable Not applicable Key 10 11 12 13 14 Number of Times Key is Pressed Keypad Characters – Hexadecimal Mode English 18 Identifying Radio Controls 15 16 17 18 19 20 21 progress, the PTT button is used to make a new call. See Making a Radio Call on page 43 for more information. • While a call is not in The microphone is activated when the PTT button is pressed. Press and hold down PTT button to talk. Release the PTT button to listen. the PTT button allows the radio to transmit to other radios in the call. • While a call is in progress, The PTT button on the side of the radio serves two basic purposes: PTT Button Push-To-Talk (PTT) Button 19 English Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20 Text Messaging Service (TMS) Icons. . . . . . . . . . . . . . page 25 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25 TMS Menu Options. . . . . . . . . . . . . . . . . . . . . . . . . . page 26 Call Type Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 27 Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . . . . page 29 Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Phone Call Display and Alert Prompts . . . . . . . . . . . . . page 34 Your radio indicates its operational status through the following: Identifying Status Indicators Identifying Status Indicators t Top Display Top Display Transmitting Radio is transmitting a call or data. Receiving Radio is receiving a call or data. The following icons are for the front display screen unless indicated otherwise. Selected icons are also shown on the first row of the 112 x 32 pixel top monochrome display screen of your radio. The 240 x 320 pixel front liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries. The top two display rows contain color icons that indicate radio operating conditions. Status Icons English 20 Identifying Status Indicators Top Display Top Display Top Display Roaming The radio has roamed to and is currently registered to a foreign system. Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. Battery For IMPRES battery operation only – the icon shown indicates the charge remaining in the battery. For all battery operation – the icon blinks when the battery is low. Call Received Radio has received an Individual Call. K Top Display Top Display the affiliated trunking talkgroup or selected conventional channel is deactivated. • Off = The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is activated. • On = The feature is enabled. Voice muting of In-Call User Alert Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). through a repeater. • Off = Radio is connected with other radios radio-to-radio communication (during conventional operation only). • On = Radio is currently configured for direct Direct Top Display Top Display Top Display or H L Top Display or H . • Blinking = Program mode • On steady = View mode View/Program Mode Radio is in the view or program mode. designated as Priority-Two. 21 English • Steady dot = Radio detects activity on channel channel designated as Priority-One. • Blinking dot = Radio detects activity on Priority Channel Scan Scan Radio is scanning a scan list. • H = Radio is set at High power. • L = Radio is set at Low power. Power Level Identifying Status Indicators or or C = Radio is in Zone 3. F = Radio is in Zone 6. E = Radio is in Zone 5. • D = Radio is in Zone 4. Basic Zone Bank 2 D E• F • Top Display or or B = Radio is in Zone 2. • A = Radio is in Zone 1. Basic Zone Bank 1 Vote Scan Enabled The vote scan feature is enabled. A B• C • Top Display Top Display English 22 Identifying Status Indicators Top Display or ... ... AB x y Top Display • Blinking = Receiving an encrypted voice call. • Off = Clear operation. • On = AES Secure operation. AES Secure Operation • Blinking = Receiving an encrypted voice call. • Off = Clear operation. • On = Secure operation. Secure Operation Enhanced Zone Bank A = Contains Zone 1, Zone 2 and Zone 3, B = Contains Zone 4, Zone 5 and Zone 6, C = Contains Zone 7, Zone 8 and Zone 9, X = Contains Zone 70, Zone 71 and Zone 72, Y = Contains Zone 73, Zone 74 and Zone 75. n Hexadecimal Indicates that the text entry is currently in hexadecimal mode. Data Activity Data activity is present. secured IP Packet Data. • Inverted = User successfully login to the registration with the server failed due to an invalid username or pin. • Blinking = Device registration or user radio. • Off = User is currently not associated with the radio. • On = User is currently associated with the User Login Indicator (IP Packet Data) available. • Blinking = feature is enabled, but no signal is • Off = feature is disabled. available. • On = feature is enabled, and signal is Signal 23 English Mixedcase Predictive Indicates that the text entry is currently in mixed case and with predicted words shown at the bottom of the screen. Lowercase Predictive Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen. Lowercase Indicates that the text entry is currently in lowercase mode. Uppercase Indicates that the text entry is currently in uppercase mode. Mixed Case Indicates that the text entry is currently in normal text mode. Start Case Indicates that the first character of the text entry is capitalized. Numeric Indicates that the text entry is currently in numeric mode. Identifying Status Indicators a Top Display Top Display English 24 Identifying Status Indicators LTE Receiving The radio is receiving LTE signal. LTE network is active LTE system is available and connected. Bluetooth Connected Bluetooth is currently connected to the external bluetooth device. Bluetooth On Bluetooth is on and ready for bluetooth connection. Uppercase Predictive Indicates that the text entry is currently in uppercase and with predicted words shown at the bottom of the screen. Blinking LTE icon is Blinking ARS user login failed while in LTE system. LTE Receiving and Transmitting while ARS user logged in The radio is receiving and transmitting LTE signal with ARS user logged in. LTE Transmitting while ARS user logged in The radio is transmitting LTE signal with ARS user logged in. LTE Receiving while ARS user logged in The radio is receiving LTE signal with ARS user logged in. LTE wtih ARS User logged in Indicating ARS user logged in successfully with LTE system. LTE Receiving and Transmitting The radio is receiving and transmitting LTE signal. LTE Transmitting The radio is transmitting LTE signal. been read. • The selected text message in the Inbox has not • User receives a new message. Unread Message Message Unsent The text message cannot be sent. Message Sent The text message is sent successfully. Inbox Full The Inbox is full. The following icons appear on the radio’s display when you send and receive text messages. Status Icons This feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 81 for more information. Text Messaging Service (TMS) Icons 3/6 “Request Reply”. 25 English • Messages in the Inbox folder are flagged with before the message is sent. • The “Request Reply” feature is toggled on Request Reply “Priority”. • Messages in the Inbox folder are flagged with message is sent. • The “Priority” feature is toggled on before the Priority Status Message Index Indicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column. Normal Message User is composing a message with normal priority and without a request for a reply. Read Message The selected text message in the Inbox has been read. Identifying Status Indicators Sends the message. Updates or saves a command. Send Yes Selects the highlighted command. Sel Returns to the previous screen. No Replies to a message. Exits to the Home screen. Exit Rply Brings you to the edit screen. Edit Brings you to the Options main screen. Deletes a message or text. Del Optn Deletes all messages. Brings you back to the previous screen. Clr Back Menu Option Description/Function “Priority” and “Request Reply”. • Messages in the Inbox folder are flagged with status and a request for a reply. • User is composing a message with a priority Priority Status and Request Reply TMS Menu Options English 26 Identifying Status Indicators Landline phone number added to a Call List. Landline phone number. Mobile number added to a Call List. Mobile number. Radio number added to a Call List. Radio number. The following icons appear on the radio’s main display, when you make or receive a call, or view selected call lists, to indicate the different call types associated with an alias or ID. Call Type Icons Incoming emergency call. Outgoing call or data. Incoming call or data. LED Indicator 27 English The LED indicator shows the operational status of your radio. LED Indicator Identifying Status Indicators Note: No LED indication when the radio receives a clear (non-secured) transmission in trunking Mode. Rapidly blinking green – Radio is on a Priority-One channel while in the Scan List Programming mode. Blinking green – Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Solid green – Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking yellow – Radio is receiving a secured transmission. Solid yellow (Conventional Only) – Channel is busy. Rapidly blinking red – Radio has failed the self test upon powering up or encountered a fatal error. Blinking red – Radio is transmitting at low battery condition. Solid red – Radio is transmitting. English 28 Identifying Status Indicators Notification Emergency Alerts Critical Alerts Call Alerts Orange Red Green When The radio receives a selective call. The radio receives a call alert. The radio receives a phone call. The radio receives a private call. The radio is unable to authenticate or register with the system. 29 English The radio is unable to establish a full connection with the system. The radio enters failsoft mode. The radio is out of range. The radio battery is low. The radio initiates Fireground Evacuation alarm. The radio initiates the Man Down Post-Alert timer. The radio receives an emergency alarm or call. The radio initiates an emergency alarm or call. This feature must be preprogrammed by a qualified radio technician. Backlight and Bar Color Note: This feature temporary changes the backlight of the top display screen, and adds a color bar to the main display screen to help signal that a radio event has occurred. Intelligent Lighting Indicators Identifying Status Indicators A Group of Low-Pitched Tones Long, Low-Pitched Tone Short, Low-Pitched Tone You Hear When system is busy. When radio is on an unpreprogrammed channel. Invalid Mode Busy (When PTT button is pressed) the radio is out of range of the system. Out of Range (When PTT button is pressed) transmissions are not allowed. After time out. Time-Out Timer Timed Out Talk Prohibit/PTT Inhibit When radio initiates Man Down mode. When radio is in an individual call for greater than 6 seconds without any activity. When radio fails to receive an acknowledgment. Man Down Entry Individual Call Warning Tone No ACK Received Four seconds before time out. When an unauthorized request is made. Reject Time-Out Timer Warning When radio fails its power-up self test. Heard Radio Self Test Fail Tone Name Your radio uses alert tones to inform you of your radio’s condition. The following table lists these tones and when they occur. Alert Tones English 30 Identifying Status Indicators A Group of Medium-Pitched Tones Long, Medium-Pitched Tone Short, Medium-Pitched Tone You Hear When Call Alert is received by the target radio. When a SmartZone trunking system fails. Site Trunking When Call Alert or Private Call is received. Received Individual Call Call Alert Sent When status, emergency alarm, or reprogram request ACK is received. When encryption key has been lost. When voice channel is available from previous request. When the trunking system fails. When exiting the emergency state. When volume is changed on a quiet channel. When central controller has received a request from a radio. Console Acknowledge Keyfail Automatic Call Back Failsoft Emergency Exit Volume Set Central Echo When entering the emergency state. When activity on a priority channel is received. Priority Channel Received Emergency Alarm /Call Entry At beginning of a non-coded communication. When radio passes its power-up self test. When a correct key is pressed. Heard Clear Voice Radio Self Test Pass Valid Key-Press Tone Name English 31 Identifying Status Indicators DecrementalPitched Tone When Bluetooth accessory is unpaired from the radio. Bluetooth Unpaired When Bluetooth accessory is disconnected from the radio. When Bluetooth accessory is connected to the radio. Bluetooth Connected Bluetooth Disconnected When Bluetooth accessory is paired with the radio. When a priority message is received. When a new message is received. (When PTT button is pressed) is verifying with the system for accepting its transmissions. Bluetooth Paired Priority Status Unique, High-Pitched Chirp IncrementalPitched Tone New Message Talk Permit (When PTT button is pressed) a dynamic ID has been received. When a land-to-mobile phone call is received. Phone Call Received Dynamic Regrouping When waiting for target of Private Call to answer the call. When system is searching for target of Private Call. When battery is below preset threshold value. Heard Enhanced Call Sent Unique, Low-Pitched Chirp Gurgle Ringing Low-Battery Chirp Short, High-Pitched Tone (Chirp) Fast Ringing Tone Name You Hear English 32 Identifying Status Indicators Enhanced Zone Bank Up Enhanced Zone Bank Down Sol-Doh When EZB Down button is pressed to scroll the Enhance Zone Bank down. When EZB Up button is pressed to scroll the Enhance Zone Bank up. When radio is in Man Down Enhanced mode and prepares to transmit Emergency Alarm when the timer of this alarm ends. 33 English When radio is in Man Down mode and prepares to transmit Emergency Alarm when the timer of this alarm ends. Man Down Continuous Tone Critical Man Down Continuous Tone Heard Tone Name Doh-Sol A Group of Very High-Pitched Tones You Hear Identifying Status Indicators Note: When a channel is not available. – When you release the PTT button. No The call is not acknowledged. acknowledge Phone busy The phone system is busy. You press the PTT button and the phone system is not available. No phone Phone busy When You See The radio indicates to the landline party that he or she may begin talking. Press H to hang up. The radio returns to the Home screen. The radio automatically connects when a channel opens. Press H to exit the phone mode and try your call later. Press H to hang up. The radio returns to the Home screen. Notes If the radio is preprogrammed for buffered overdial, the digits pressed are entered into memory and then sent when the PTT button is pressed. Press the PTT button to send either digits or voice, but not both at the same time. You have the option of sending additional digits (overdial), such as an extension number, or credit card or PIN numbers, to the phone system. If the radio is preprogrammed for live overdial, every digit entered after the call is connected is sent to the phone system. A HighPitched Tone – A Busy Tone A Long Tone You Hear The following appears on the radio’s display when you make and receive Phone calls. The radio also uses alert tones to indicate the current status. Phone Call Display and Alert Prompts English 34 Identifying Status Indicators Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 35 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 36 Using Channel Search Button . . . . . . . . . . . . . . . . . . . page 38 Using Mode Select Feature . . . . . . . . . . . . . . . . . . . . . page 39 Receiving and Responding to a Radio Call . . . . . . . . . page 40 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 43 Repeater or Direct Operation . . . . . . . . . . . . . . . . . . . page 46 Monitoring Features. . . . . . . . . . . . . . . . . . . . . . . . . . . page 46 Use this navigation guide to familiarize yourself with the basic Call features: Once you understand how your radio is configured, you are ready to use your radio. General Radio Operation 3-Position A/B/C Switch Your radio must be preprogrammed to allow you to use this feature. 35 English Procedure: Move the preprogrammed Zone (3-Position A/B/C) switch to the position of the required zone and proceed to Step 3. Note: Use the following procedure to select a zone. A zone is a group of channels. Selecting a Zone General Radio Operation Note: Positions of ZnUp and ZnDn on the display may differ each time you release the Menu Select button. Read carefully before you press. or ZnDn until the required zone appears. Note: 2 Press and hold the Menu Select button directly below ZnUp Consult a qualified radio technician for the right choice between the following methods. Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with both audio and visual warnings. Use the following procedure to select a channel. A channel is a group of radio characteristics, such as transmit/ receive frequency pairs. Selecting a Radio Channel 1 < or > to ZnUp or ZnDn. OR Follow the procedure below. channel. 5 Press the PTT button to transmit on the displayed zone shows Invalid entry. Repeat Step 3. OR Press the Menu Select button directly below Sel to confirm the displayed zone. 4 If the zone number entered is unprogrammed, the display OR Use the keypad to enter the zone number. 3 U or D to the required zone. 2 Press the Menu Select button directly below Zone. 1 < or > to Zone. OR Follow the procedure below. English 36 General Radio Operation 3 Press the PTT button to transmit on the displayed zone and 1 < or > to Chan. channel. 5 Press the PTT button to transmit on the displayed zone shows Invalid entry. Repeat Step 3. OR Press the Menu Select button directly below Sel to confirm the selected channel. 4 If the channel number entered is unprogrammed, the display OR Use the keypad to enter the channel number. 3 U or D to the required channel. 2 Press the Menu Select button directly below Chan. 2 Press the Menu Select button directly below ChUpor ChDn. Note: 37 English Positions of ChUp and ChDn on the display may differ each time you release the Menu Select button. Read carefully before you press. channel. 1 < or > to ChUp or ChDn. OR Follow the procedure below. Procedure: Turn the preprogrammed 16-Position Select Knob to the desired channel. OR Follow the procedure below. General Radio Operation Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 3 A blinking cursor appears on the Channel Search screen. the channel name. 2 Press the Menu Select button directly below CSrh to key in 1 < or > to CSrh. Procedure: Press the preprogrammed Channel Search button. OR Follow the procedure below. This feature allows you to do a quick search for a specific channel in your radio by keying in the alias of the channel. If the name matches, your radio prompts the first found matched channel name. Using Channel Search Button English 38 General Radio Operation and the radio changed its transmission to this channel. OR If the entry does not match, the display shows Channel name not found. Repeat from step 3 if want to search again; or press H or the Menu Select button directly below Exit to exit. 6 Once found, the display shows the matched channel name OR If the radio is triggered to search for an empty entry, the display shows Invalid entry. Repeat step 3. 5 The display shows Searching. entry is done to initiate searching. OR Press the Menu Select button directly below Cncl to exit. 4 Press the Menu Select button directly below CSrh once the Note: Your radio must be preprogrammed to allow you to use this feature. • Programmable buttons and keypad buttons (digit 0 to 9) • Softkeys There are two methods to save the selected zone and channel: Mode Select allows a long press to save your radio’s current zone and channel to a programmable button, keypad button or a softkey; then once programmed, the short-press of that button or softkey jumps the transmission to the saved zone and channel. Using Mode Select Feature To change the programmed zone and channel, repeat this procedure. 39 English Short press of the programmed softkey changes your current transmission to the zone and channel programmed in this softkey. Note: channel is saved. 4 You hear a short, medium-pitched tone when the zone and softkey. 3 Press and hold the Menu Select button directly below the 2 < or > to MS1, MS2 ... or MS5. channel. 1 Toggle your zone and channel to the required zone and Procedure: Five softkeys are available for you to save the frequent used zone and channel. Saving a Zone and Channel to a Softkey General Radio Operation Repeat this procedure to change the zone and channel of the programmed button. Short press of the programmed button changes your current transmission to the zone and channel programmed in this button. Note: channel is saved. 3 You hear a short, medium-pitched tone when the zone and 2 Press and hold the digit button you desire to program. channel. 1 Toggle your zone and channel to the required zone and Procedure: All the programmable buttons and keypad digit 0 to 9 buttons allow you to save the frequent used zone and channel. Saving a Zone and Channel to a Keypad Button English 40 General Radio Operation If the radio is receiving a secure transmission, the LED blinks yellow. The LED lights up solid red while the radio is transmitting. In conventional mode, the LED lights up solid yellow when the radio is receiving a transmission. In trunking mode, there is no LED indication when the radio receives a transmission. LED Indicator Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. Receiving and Responding to a Radio Call See Making a Talkgroup Call on page 43 for details on making a Talkgroup Call. 4 Release the PTT button to listen. is in the call list. OR 41 English 3 During the call, the display shows the caller alias (name), if it OR Press the Call Response button within 20 seconds after the call indicators begin. 2 Press the Menu Select button directly below Resp. display shows Call received and the call received icon blinks. 1 You hear two alert tones and the LED blinks green. The up solid red. your mouth. 3 Press the PTT button to respond to the call. The LED lights The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: When you receive a Private Call: Note: These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID. A Private Call is a call from an individual radio to another individual radio. (Trunking Only) Receiving and Responding to a Private Call 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. OR Trunking Only: The display shows the caller alias or ID. 1 ASTRO Conventional Only: Procedure: When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed: To receive a call from a group of users, your radio must be configured as part of that talkgroup. Receiving and Responding to a Talkgroup Call General Radio Operation See Making a Private Call (Trunking Only) on page 43 for details on making a Private Call. return to the Home screen. 5 Press H or the Call Response button to hang up and button to listen. 4 Press and hold the PTT button to talk. Release the PTT During the call, the display shows the caller ID (number), if the caller’s name is not in the call list. English 42 General Radio Operation The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. See Making a Telephone Call (Trunking Only) on page 45 for details on making a Telephone Call. return to the Home screen. 4 Press H or the Call Response button to hang up and button to listen. 3 Press and hold the PTT button to talk. Release the PTT call indicators begin. 2 Press the Call Response button within 20 seconds after the The backlight of the screen and the bar turns green. The display shows Phone Call and the call received icon blinks. 1 You hear a telephone-type ringing and the LED blinks green. Procedure: Use the preprogrammed Call Response button to answer a Telephone Call: Note: This feature allows you to receive calls similar to standard phone calls from a landline phone. (Trunking Only) Receiving and Responding to a Telephone Call The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. 3 Press the PTT button to make the call. your mouth. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from channel with the desired talkgroup. 1 Turn the 16-Position Select Channel Knob to select the Procedure: To make a call to a group of users, your radio must be configured as part of that talkgroup. Making a Talkgroup Call Note: page 61) 43 English through and select the required ID. OR Press the Menu Select button directly below LNum to go to the last number dialed. OR 3 Press the Menu Select button directly below Cnts to scroll display shows the last transmitted or received ID. 2 Press the Menu Select button directly below Call. The 1 < or > to Call. Procedure: Press the preprogrammed Quick Access (One-Touch) Private Call button to dial the preprogrammed ID (number) and proceed to Step 5. OR Follow the procedure below. Making a Private Call (Trunking Only) 6 Release the PTT button to listen. • A preprogrammed One Touch Call button • The Contacts list (see Viewing Details of a Contact on 5 Speak clearly into the microphone. The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only: The LED lights up solid red. 4 ASTRO Conventional Only: • The 16-Position Select Channel Knob • The preprogrammed Zone switch You can select a zone, channel, subscriber ID, or talkgroup by using: Making a Radio Call General Radio Operation target radio. Press and hold the PTT button to talk. Release the PTT button to listen. 7 When you are connected, the display shows the ID of the your mouth. 6 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from Note: Your radio must be preprogrammed to allow you to use this feature. 5 The display shows Calling.... 4 Press the PTT button to initiate the Private Call. through and select the required ID. OR Press the Menu Select button directly below LNum to go to the last number dialed. OR U or D to the required ID. OR Use the keypad to enter the required ID. 3 Press the Menu Select button directly below Cnts to scroll display shows the last transmitted or received ID. 2 Press the Menu Select button directly below Call. The 1 < or > to Call. Procedure: Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. This feature allows you to send an individual Call Alert page if there is no answer from the target radio. See Sending a Call Alert Page on page 66 for more information. Making an Enhanced Private Call (Trunking Only) 8 Press H to return to the Home screen. target radio. Press and hold the PTT button to talk. Release the PTT button to listen. OR If no acknowledgment is received, the display shows No acknowledge. 7 When you are connected, the display shows the ID of the your mouth. 6 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from 5 The display shows Calling... . 4 Press the PTT button to initiate the Private Call. OR Use the keypad to enter the required ID. U or D to the required ID. English 44 General Radio Operation through and select the required ID. OR Press the Menu Select button directly below LNum to go to the last number dialed. 3 Press the Menu Select button directly below Cnts to scroll display shows the last transmitted phone number. 2 Press the Menu Select button directly below Phon. The 1 < or > to Phon. Procedure: Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5. OR Follow the procedure below. This feature allows you to make calls similar to standard phone calls to a mobile or landline phone. Making a Telephone Call (Trunking Only) 8 Press H to return to the Home screen. OR If no acknowledgment is received, the display shows No acknowledge. OR If the target radio does not respond before the time out, the display shows No answer. 45 English See Phone Call Display and Alert Prompts on page 34 for more information if your call is NOT answered. 7 Press H to return to the Home screen. Release the PTT button to listen. 6 When your call is answered, press the PTT button to talk. your mouth. 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from 4 Press and release the PTT button to dial the phone number. OR U or D to the required phone number. OR Use the keypad to enter the required phone number. General Radio Operation 6 Release the PTT button to receive (listen). up solid red. 5 Press and hold the PTT button to transmit. The LED lights 4 Release the Volume Set button. 3 Adjust the Volume Control Knob if necessary. set tone. 2 Press and hold the Volume Set button to hear the volume 1 Select the desired zone and channel. 3 The display shows Repeater mode if the radio is currently in Repeater mode. OR The display shows Direct mode and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only). Procedure: Use the preprogrammed Volume Set Button button. Monitoring a Channel Use the Monitor feature to make sure a channel is clear before transmitting. This digital technology quiets the transmission by removing the “noise” from the signal and allows only the clear voice or data information to be heard. Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Monitoring Features 2 Press the Menu Select button directly below Dir. 1 < or > to Dir. Procedure: Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below. The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. The REPEATER operation increases the radio’s range by connecting with other radios through a repeater. The transmit and receive frequencies are different. Repeater or Direct Operation English 46 General Radio Operation The Carrier Squelch indicator appears on the display when you monitor a channel via the preprogrammed Monitor button. 5 Release the PTT button to receive (listen). up solid red. 4 Press and hold the PTT button to transmit. The LED lights 3 Adjust the Volume Control Knob if necessary. 2 Listen for a transmission. 1 Select the desired zone and channel. Follow the procedure below. OR Press the preprogrammed Monitor button and proceed to Step 3. OR 47 English If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. to the original squelch setting. 3 Press the Monitor button again, or the PTT button, to return monitor operation. The duration of the button press is programmable. 2 Press and hold the Monitor button to set continuous The Carrier Squelch indicator appears on the display. 1 Momentarily press the Monitor button to listen for activity. Procedure: Your radio may be preprogrammed to receive Private-Line® (PL) calls. Conventional Mode Operation General Radio Operation Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . page 49 Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 55 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 61 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 64 Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 65 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . page 67 Fireground (Conventional Only) . . . . . . . . . . . . . . . . . page 71 Tactical Public Safety (TPS) (Conventional Only) . . . page 73 Man Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 74 Automatic Registration Service (ARS) . . . . . . . . . . . . page 78 Text Messaging Service (TMS) . . . . . . . . . . . . . . . . . . page 81 ASTRO 25 Advanced Messaging Solution . . . . . . . . . page 92 Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . page 97 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 103 Use this navigation guide to learn more about advanced features available with your radio: Advanced Features English 48 Advanced Features Radio Stun and Kill . . . . . . . . . . . . . . . . . . . . . . . . . . page 105 The Global Positioning System (GPS). . . . . . . . . . . . page 107 Trunking System Controls . . . . . . . . . . . . . . . . . . . . . page 115 Mission Critical Wireless (MCW) - Bluetooth® - . . . . page 117 Programming Over Project 25 (POP 25) (ASTRO 25 and ASTRO Conventional) . . . . . . . . . . . . . . . . . . . . . . page 132 Voice Announcement. . . . . . . . . . . . . . . . . . . . . . . . . page 133 Using Site Selectable Alerts (ASTRO 25) . . . . . . . . . page 134 Long Term Evolution (LTE) (APX 7000L Only) . . . . . page 140 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 145 button to listen. 4 Press and hold the PTT button to talk. Release the PTT your mouth. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from 2 The speaker unmutes. and the LED lights up solid yellow. The call received icons blinks and the display shows Call received. You hear two alert tones, the LED lights up solid yellow to indicate the transmitting radio is still sending signal. OR the LED blinks solid green once to indicate the transmitting radio is pending to receive signal. 1 When you receive a Selective Call, you hear two alert tones Procedure: Receiving a Selective Call This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Conventional Only) Receiving and Making a Selective Call (ASTRO Advanced Call Features The display shows the ID of the target radio. 49 English 5 Press and hold the PTT button to initiate the Selective Call. your mouth. 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from through and select the required ID. OR Press the Menu Select button directly below LNum to go to the last number dialed. OR U or D to the required ID. OR Use the keypad to enter the required ID. 3 Press the Menu Select button directly below Cnts to scroll display shows the last transmitted or received ID. 2 Press the Menu Select button directly below Call. The 1 < or > to Call. Procedure: Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4. OR Follow the procedure below. Making a Selective Call Advanced Features Encryption keys are associated to talkgroups. When talkgroups are associated, encryption keys are changed by changing the active talkgroup. See Secure Operations on page 97 for more information. OR U or D to the required talkgroup. OR 3 U or D to Preset for the preset preprogrammed talkgroup. display shows the last talkgroup that was selected and stored, Sel and Exit. 2 Press the Menu Select button directly below Tgrp. The 1 < or > to Tgrp. Procedure: Selecting a Talkgroup Note: This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel. Operation Only) Using the Talkgroup Call Feature (Conventional 7 Press H to return to the Home screen. 6 Release the PTT button to listen. English 50 Advanced Features The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Status button and proceed to Step 3. Note: Each status can have up to a 14-character name. A maximum of eight status conditions is possible. This feature allows you to send data calls to the dispatcher about a predefined status. Sending a Status Call 6 Press H to return to the Home screen. erased, you hear a momentary key fail tone and the display shows Key fail. OR If the encryption key that is associated to the new talkgroup is not allowed, you hear a momentary key fail tone and the display shows Illegal key. 5 If the encryption key associated to the new talkgroup is currently selected talkgroup and return to the Home screen. 4 Press the Menu Select button directly below Sel to save the Use the keypad to enter the number of the corresponding talkgroup in the list. No traffic is heard on trunked channels while Status Call is selected. If the radio detects no Status Call activity for six seconds, you will hear an alert tone until you press H or the PTT button. 7 Press H to return to the Home screen. and the display shows Ack received. The radio returns to normal dispatch operation. OR If no acknowledgment is received, you hear a low-pitched tone and the display shows No acknowledge. 6 When the dispatcher acknowledges, you hear four tones 5 Press the PTT button to send the status. OR Use the keypad to enter a number corresponding to the in the status list. 4 U or D to the required status. first status in the list. 3 The display shows the last acknowledged status call, or the 2 Press the Menu Select button directly below Sts. 1 < or > to Sts. OR Follow the procedure below. If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, you hear an invalid tone. 51 English When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. 2 Press the PTT button to talk. Release PTT button to listen. switches to the dynamically regrouped channel. You hear a “gurgle” tone and the display shows the dynamically regrouped channel’s name. 1 When your radio is dynamically regrouped, it automatically Procedure: Note: You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. This feature allows the dispatcher to temporarily reassign selected radios to a particular channel where they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. (Trunking Only) Using the Dynamic Regrouping Feature Advanced Features • Select-enabled radios are free to change to any available Procedure: Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below. Note: 4 If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows Ack received and the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, you hear a low-pitched alert tone and the display shows No acknowledge. Try again or press H to cancel and return to the Home screen. This feature provides one or more Dynamic Zones to store the frequent used channels be it conventional or trunking. These dynamic channels are saved from pre-existing (non-dynamic) channels in the radio. This saves the time and effort from the regular navigation around the working zones and channels. User can also delete or update the list in the Dynamic Zone. Your radio must be preprogrammed to allow you to use this feature. This feature works on the condition at least one zone in the radio must be a non-dynamic zone. Using Dynamic Zone Programming (DZP) 3 The display shows Reprgrm rqst and Please wait. reprogram request to the dispatcher. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. • Select-disabled radios cannot change channels while 2 Press the Menu Select button directly below Rpgm to send 1 < or > to Rpgm. The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. This feature allows you to notify the dispatcher when you want a new dynamic regrouping assignment. channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position. Classifying Regrouped Radios Requesting a Reprogram (Trunking Only) English 52 Advanced Features display shows Search Options screen. 2 Press the Menu Select button directly below Edit. The ZnPr to enter Program Zone screen. 1 < or > to ZnPr. Press the Menu Select button directly below Procedure: With the radio in Dynamic Zone, follow the procedure below. Selection Saving a Channel in the Dynamic Zone from List returns to Home screen with the selected shown on the screen. OR Press the Menu Select button below Exit. The display returns to Home screen without any changes. 4 Press the Menu Select button below Sel. The display 3 U or D to . display shows the Zone screen. 2 Press the Menu Select button directly below Zone. The 1 < or > to Zone. Procedure: Channel Entering the Dynamic Zone to Select a Dynamic Use the keypad to type or edit the channel name. 53 English 4 A blinking cursor appears on the Channel Name screen. directly below Sel. The display shows Channel Name screen. 3 U or D to Channel Name. Press the Menu Select button display shows Search Options screen. 2 Press the Menu Select button directly below Edit. The ZnPr to enter Program Zone screen. 1 < or > to ZnPr. Press the Menu Select button directly below Procedure: With the radio in Dynamic Zone, follow the procedure below. Channel Name Saving a Channel in the Dynamic Zone from to Home screen. 6 Press the Menu Select button directly below Exit to return button directly below Sel. The display shows Channel updated. 5 U or D to the required channel. Press the Menu Select directly below Sel. The display shows Select Chan screen. 4 U or D to the required zone. Press the Menu Select button directly below Sel. The display shows Select Zone screen. 3 U or D to List Selecton. Press the Menu Select button Advanced Features 8 Press H to return to Home screen. OR If the entry does not match, the display shows Channel name not found. Repeat from step 4 or 5 if want to search again. 7 Once found, the display shows Channel updated. OR If the radio is triggered to search for an empty entry, the display shows Invalid entry. Repeat step 4. 6 The display shows Searching.... entry is done to initiate searching. OR Press the Menu Select button directly below Cncl to return to Search Options screen. 5 Press the Menu Select button directly below Srch once the Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. English 54 Advanced Features OR The Home screen shows +“Blank” if the channel deleted is the Home channel. 5 The Home screen shows . screen. 4 Press the Menu Select button below Exit to return to Home Select button directly below Del. The display shows Channel deleted. 3 U or D to the saved dynamic channel. Press the Menu 2 The display shows the dynamic channels list. ZnPr to enter Program Zone screen. 1 < or > to ZnPr. Press the Menu Select button directly below Procedure: With the radio in Dynamic Zone, follow the procedure below. Deleting a Channel in the Dynamic Zone The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information. Note: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries. below Sel. 55 English 5 U or D to Call and press the Menu Select button directly 4 Press the Menu Select button directly below Optn. 3 U or D to the required subscriber alias. entries are alphabetically sorted. 2 Press the Menu Select button directly below Cnts. The • WACN ID (Astro 25 Trunking IDs only) • System ID 1 < or > to Cnts. • Call Type (Icon) Use the Options Menu. • Call ID (Number) Your radio must be preprogrammed to allow you to use this feature. Procedure: Note: Making a Private Call from Contacts Note: Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs (numbers). • Call Alias (Name) Each entry within Contacts displays the following information: Additionally, each entry, depending on context (conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call, Selective Call, Private Call, or Call Alert. Contact entries are alphabetically sorted according to entry alias. Each alias can have up to five IDs of different call types associated with it. This feature provides “address-book” capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call. Contacts Advanced Features 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The subscriber alias. 4 < or > to scroll through the available IDs for the selected 3 U or D to the required subscriber alias. below Edit. 4 U or D to Name and press the Menu Select button directly button directly below Sel. 3 U or D to {New Contact} and press the Menu Select entries are alphabetically sorted. Procedure: Use the PTT button. entries are alphabetically sorted. Adding a New Contact Entry time, the call ends. OR The call ends when it reaches the maximum ring time. 8 If there is no voice activity for a preprogrammed period of solid red. OR Release the PTT button to listen. The LED lights up solid yellow. 7 Press and hold the PTT button to talk. The LED lights up display shows the subscriber alias. 6 Press the PTT button to initiate the call. During the call, the your mouth. 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from OR time, the call ends. OR The call ends when it reaches the maximum ring time. 10 If there is no voice activity for a preprogrammed period of solid red. OR Release the PTT button to listen. 9 Press and hold the PTT button to talk. The LED lights up display shows the subscriber alias. 8 Press the PTT button to initiate the call. During the call, the your mouth. 7 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from 6 U or D to select the call type. English 56 Advanced Features appears. Use the keypad to enter the number. Press < to move one space to the left. Press > to move one space to the right. 9 The display shows Edit Number 1 and a blinking cursor directly below Edit. 8 U or D to Number 1 and press the Menu Select button directly below Sel. 7 U or D to {Add Number} and press the Menu Select button have entered the name. OR Press the Menu Select button directly below Cncl to return to the previous screen. 6 Press the Menu Select button directly below Ok once you appears. Use the keypad to enter the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 5 The display shows Edit name and a blinking cursor 14 The radio returns to the main Contacts screen. contact entry has been added. 57 English 13 The display shows Stored, confirming that the have finished. 12 Press the Menu Select button directly below Done once you below Edit. U or D to the required mode and press the Menu Select button directly below Ok. OR Repeat Steps 8 through 10 to enter or edit the existing system IDs. OR U or D to {Add Number} and press the Menu Select button directly below Sel to add a new number. Repeat Steps 8 through 10. 11 U or D to Type 1 and press the Menu Select button directly have entered the number. OR Press the Menu Select button directly below Cncl to return to the previous screen. 10 Press the Menu Select button directly below Ok once you Press the Menu Select button directly below Del to delete any unwanted characters. Advanced Features 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. 2 Press the Menu Select button directly below Cnts. The The display shows deleted and the radio returns to the main screen for Contacts. OR Select No to return to the main screen for Contacts. 6 Select Yes to delete the entry. 5 The display shows Delete confirm?. below Sel. 4 U or D to Delete and press the Menu Select button directly Select button directly below Optn. 3 U or D to the entry you want to delete and press the Menu 7 The radio returns to the main display for Contacts. added to Call List, confirming the addition of the contact to the list. 6 The display shows momentary Please wait before showing button directly below Add. OR U or D to Cncl to return to the main display for Contacts. 5 U or D to the required Call List and press the Menu Select directly below Sel. 4 U or D to Add to CallLst and press the Menu Select button the Menu Select button directly below Optn. 3 U or D to the entry you want to add to a call list and press entries are alphabetically sorted. Procedure: Procedure: entries are alphabetically sorted. Adding a Contact to a Call List Deleting a Contact Entry English 58 Advanced Features 8 The radio returns to the main display for Contacts. removed from Call List, confirming the removal of the contact from the list. 7 The display shows momentary Please wait before showing the entry from the Call List. OR Press the Menu Select button directly below No to return to the main display for Contacts. 6 Press the Menu Select button directly below Yes to remove 5 The display shows Remove frm Call List?. directly below Sel. 4 U or D to Rm frm CallLst and press the Menu Select button press the Menu Select button directly below Optn. 3 U or D to the entry you want to remove from a call list and entries are alphabetically sorted. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. Procedure: Removing a Contact from a Call List 59 English Use the keypad to edit the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 A blinking cursor appears. Menu Select button directly below Edit. 5 U or D to the entry alias you wish to change and press the below Sel. 4 U or D to Edit and press the Menu Select button directly Select button directly below Optn. 3 U or D to the entry you want to edit and press the Menu entries are alphabetically sorted. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. Procedure: Editing an Entry Alias Editing a Contact in a Call List Advanced Features Use the keypad to edit the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. 6 A blinking cursor appears. Menu Select button directly below Edit. 5 U or D to the entry ID you wish to change and press the below Sel. 4 U or D to Edit and press the Menu Select button directly Select button directly below Optn. 3 U or D to the entry you want to edit and press the Menu entries are alphabetically sorted. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. Procedure: the Menu Select button directly below Ok to select. 6 U or D to choose from the list of call types given and press below Edit. 5 U or D to Type and press the Menu Select button directly below Sel. 4 U or D to Edit and press the Menu Select button directly Select button directly below Optn. 3 U or D to the entry you want to edit and press the Menu entries are alphabetically sorted. 2 Press the Menu Select button directly below Cnts. The 1 < or > to Cnts. Procedure: Editing a Call Type your changes and return to the main screen for Contacts. 8 Press the Menu Select button directly below Done to save have finished. The display returns to the Edit Contact screen. Editing as Entry ID 7 Press the Menu Select button directly below Ok once you your changes and return to the main screen for Contacts. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 8 Press the Menu Select button directly below Done to save have finished. The display returns to the Edit Contact screen. 7 Press the Menu Select button directly below Ok once you English 60 Advanced Features entry. 5 The display shows all the numbers associated with the below Sel. 4 U or D to View and press the Menu Select button directly Select button directly below Optn. 3 U or D to the entry you want to view and press the Menu screen. 61 English 4 Press H to exit the current display and return to the Home 3 U or D to view the members on the list. 2 Press the Menu Select button directly below ScnL. 1 < or > to ScnL. Procedure: Viewing a Scan List Please refer to a qualified radio technician for the maximum number of Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. • Talkgroup Scan List • Conventional Scan List 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. • Trunking Priority Monitor Scan List Your radio supports different types of Scan Lists: Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Scan Lists 1 < or > to Cnts. Procedure: Viewing Details of a Contact your changes and return to the main screen for Contacts. 8 Press the Menu Select button directly below Done to save 7 The display returns to the Edit Contact screen. Advanced Features or change the priority of the currently displayed channel in the scan list. OR Press the Menu Select button directly below Del to delete the currently displayed channel from the scan list. OR Press the Menu Select button directly below Rcl to view the next member of the scan list. 4 Press the Menu Select button directly below Sel to add and/ 3 U or D to the entry you want to edit. display shows the lists that can be changed. 2 Press the Menu Select button directly below ScnL. The 1 < or > to ScnL. Procedure: Long press the preprogrammed Scan List Programming button (side button) and proceed to Step 3. OR Move the preprogrammed Scan List Programming switch to programming position and proceed to Step 3. OR Follow the procedure below. This feature lets you change scan list members and priorities. Editing the Scan List English 62 Advanced Features See Viewing and Changing the Priority Status on page 63 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. programming position. OR Press H to exit scan list programming and return to the Home screen. 6 Move the Scan List Programming switch out of OR Use the keypad to go directly to additional channels to be added or deleted. OR Use the 16-Position Select knob to select additional channels to be added or deleted. 5 U or D to select more channels to be added or deleted. 1 Below the Sel, Del, and Rcl screen, press the Menu Select 1 Long press the preprogrammed Scan List Programming programming position. 6 Move the Scan List Programming switch out of want to change. OR Use the keypad to go directly to that scan list member. OR Use the 16-Position Select knob to select another scan list member. 5 U or D to select more list members whose scan status you channel to the scan list. OR Press the Select button one or more times to change the scan list status icon of the currently displayed channel. 4 Press the Select button once to add the currently displayed 3 U or D to the number you want to edit. list member. 2 The display shows the programming mode icon and the first 63 English list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the PriorityOne channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. 2 A Scan icon indicates that the current channel is in the scan button directly below Sel to view and/or change the priority status of the currently displayed channel. OR Below the Sel, Del, and Rcl screen, press the Select button one or more times to view and/or change the scan list status icon of the currently displayed channel. Procedure: Procedure: button (side button). OR Move the preprogrammed Scan List Programming switch to programming position. Viewing and Changing the Priority Status Changing the Scan List Status Advanced Features 4 The radio returns to the Home screen. Menu Select button directly below Scan to enable scan. OR The display shows Scan on and the scan status icon if scan is enabled. Press the Menu Select button directly below Scan to disable scan. 3 The display shows Scan off if scan is disabled. Press the 2 Press the Menu Select button directly below Scan. 1 < or > to Scan. Procedure: Press the preprogrammed Scan button, or turn the preprogrammed Scan switch to the Scan on or Scan off position, to initiate or stop scan. OR Follow the procedure below. Turning Scan On or Off This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Scan English 64 Advanced Features This capability does not apply to priority channels or the designated transmit channel. If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list. Deleting a Nuisance Channel list. 2 The radio continues scanning the remaining channels in the new Priority-Two channel, press the preprogrammed Dynamic Priority button. 1 When the radio locks onto the channel designated as the Procedure: This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. Scan Only) Making a Dynamic Priority Change (Conventional • Change the channel via the 16-Position Select knob. OR or menu. • Stop and restart a scan via the preprogrammed Scan button OR Receiving a Call Alert Page • Turn the radio off and then turning it on again. 65 English Press any button to clear the Call Alert page. See Making a Talkgroup Call on page 43 or Making a Private Call (Trunking Only) on page 43 for more information on returning the call. received. 2 The call received icons blinks and the display shows Page alert tones and the LED blinks green. 1 When you receive a Call Alert page, you hear four repeating Procedure: This feature must be preprogrammed by a qualified radio technician. Note: Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a call alert page if there is no answer after the maximum ring time, OR when you press the PTT button. Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system. This feature allows your radio to work like a pager. Call Alert Paging Procedure: To restore the deleted nuisance channel, do one of the following: Restoring a Nuisance Channel list. 2 The radio continues scanning the remaining channels in the press the preprogrammed Nuisance Delete button. OR < or > to Nuis. Press the Menu Select button directly below Nuis. 1 When the radio is locked onto the channel to be deleted, Procedure: Advanced Features and the display shows Ack received. OR 7 If the call alert page is sent successfully, you hear a tone 6 If the call alert page is sent successfully, you hear a tone and the display shows Ack received. OR 6 The display shows Paging... . the call alert page. OR Press the Menu Select button directly below No to exit the screen without sending the call alert page. 5 Press the Menu Select button directly below Yes to send period of time, the display shows Send page?. 4 If the target radio does not respond after a preprogrammed initiate the call. 5 The display shows Paging... . 4 Press the PTT button to send the page. OR U or D to the required ID. OR Use the keypad to enter the required ID. 3 Press Cnts to scroll through and select the required ID. 2 Press the Menu Select button directly below Page. 3 U or D to select the alias or ID, and press the PTT button to 1 < or > to Page. 1 < or > to Call. OR Follow the procedure below. OR Press the Menu Select button directly below Ok to return to the main screen for Contacts. 7 The radio returns to the Home screen. 2 Press the Menu Select button directly below Call. The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge. Procedure: Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. Note: Sending a Call Alert Page English 66 Advanced Features OR Press the Menu Select button directly below Ok to return to the main screen for Contacts. 8 The radio returns to the Home screen. If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge. Note: 67 English To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. Each channel can only assigned one of the Emergency modes above. The radio responds differently when pressing the preprogrammed Emergency button in each channel. Check with your dealer or system administrator for more information on the programming of this feature. • Silent Emergency Alarm • Emergency Alarm with Emergency Call • Emergency Call (Trunking Only) • Emergency Alarm Your radio supports the following Emergency modes: If the Top (Orange) button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. The Emergency feature is used to indicate a critical situation. Emergency Operation Advanced Features radio reverts to the preprogrammed emergency talkgroup to send alarm and/or make emergency call. • Non-Tactical/Revert for Trunking system – The The radio reverts to the preprogrammed emergency channel to send alarm and/or make emergency call. • Non-Tactical/Revert for Conventional system – alarm and/or make emergency call on the current selected channel. • Tactical/Non-Revert – The radio sends emergency The radio operates in the normal dispatch manner while in Emergency Call, except if enabled, it returns to one of the following: See Man Down on page 74 for details. Man Down is an alternate way to activate the Emergency feature on the condition the Emergency must be set up for this feature to operate. Note: English 68 Advanced Features Emergency button press timer by default is set to 1 second. This timer is programmable from 0 – 6 seconds by a qualified technician. display shows Ack received. You hear four tones, the alarm ends, and the radio exits the Emergency Alarm mode. OR If no acknowledgment is received, the display shows No acknowledge. The alarm ends when the timer expires and the radio exits the Emergency Alarm mode. 3 When you receive the dispatcher’s acknowledgment, the channel. You hear a short medium-pitched tone and the LED blinks red momentarily. OR You hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode. 2 The display shows Emergency on the current zone and 1 Press the preprogrammed Emergency button. Procedure: Note: This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Sending an Emergency Alarm Emergency button for about a second. 6 To exit Emergency Call, press and hold the preprogrammed a response from the dispatcher. 5 Release the PTT button to end the transmission and wait for microphone. 4 Press and hold the PTT button. Speak clearly into the your mouth. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from channel. You hear a short, medium-pitched tone and the LED blinks red momentarily. OR You hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode. 2 The display shows Emergency on the current zone and 1 Press the preprogrammed Emergency button. Procedure: This feature gives your radio priority access to a talkgroup. Sending an Emergency Call (Trunking Only) your mouth. 69 English 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from Emergency Call state when: You receive the dispatcher’s acknowledgment. The display shows Ack received. OR You receive no acknowledgment. The display shows No acknowledge. OR You press the PTT button while in the Emergency Alarm mode. 3 The radio exits Emergency Alarm and enters the channel. You hear a short, medium-pitched tone and the LED blinks red momentarily. OR You hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode. 2 The display shows Emergency on the current zone and 1 Press the preprogrammed Emergency button. Procedure: This feature gives your radio priority access on a channel for conventional system, and to a talkgroup for trunking system. Call Sending an Emergency Alarm with Emergency Advanced Features Press and hold the preprogrammed Emergency button for about a second to exit the Silent Emergency Alarm mode. OR Press and release the PTT button to exit the Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode. 3 The silent emergency state continues until you: and you hear no tones. 2 The display shows no changes, the LED does not light up, 1 Press the preprogrammed Emergency button. Procedure: This feature allows you to send an Emergency Alarm to the system without triggering any audio or visual indicators. Sending a Silent Emergency Alarm Emergency button for about a second. 7 To exit Emergency Call, press and hold the preprogrammed a response from the dispatcher. 6 Release the PTT button to end the transmission and wait for microphone. 5 Press and hold the PTT button. Speak clearly into the English 70 Advanced Features Note: See Sending an Emergency Alarm on page 68, Sending an Emergency Call (Trunking Only) on page 69, Sending an Emergency Alarm with Emergency Call on page 69, or Sending a Silent Emergency Alarm on page 70. The radio only exits the Emergency state using one of the ways mentioned in the previous sections. This feature, when enabled, prevents the radio from being turned off via the On/Off Control Knob when the radio is in the Emergency state. Using the Emergency Keep-Alive Feature the display shows No emergency, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for Emergency. • If the new channel is NOT preprogrammed for Emergency, you can change channels while in Emergency operation. The emergency alarm or call continues on the new channel. • If the new channel is also preprogrammed for Emergency, For ALL Emergency transmissions, when changing channels: Changing Channels during Emergncy If you have a critical situation, you can press the Emergency button which activates an alarm on the Incident Management Software at the command terminal. Each Fireground Communication System radio automatically reports your radio’s ID on the commander’s mobile command terminal. Your name, riding position and sector can be configured to be seen at the Commander’s command terminal. The radio helps to indicate your presence on the scene if it is in the range of the Incident Commander’s command terminal. These components provide on-scene and inbuilding radio coverage, and enhanced personnel accountability and monitoring. • DVRS (Optional) • Radio Frequency (RF) Modem • Command Terminal • Incident Management Software • Your portable radios The portable Fireground Communications System is designed for deployment at an incident scene. It consists of five central components: Fireground (Conventional Only) 71 English If the Fireground Zone Channel is set as default, you hear gurgle tones and the home screen appears. You are in Fireground zone channel. OR If the Fireground Zone Channel is set as default, but you hear a short, low-pitched tone, the display shows Reg failed to indicate that the command terminal does not respond to Fireground Zone Channel. Get qualified technician for assistance. OR Your home channel is not Fireground Zone Channel, toggle or change the radio zone channel to Fireground Zone Channel. 1 Upon Powering Up Procedure: Entering Fireground Zone Channel • Sending an Emergency Alarm and Call • Pressing the PTT button to make voice transmission • Response to Evacuation commands • Automatic response to Polling • Powering up or down the radio The Fireground signals transmission is always exchanging data between your radio and the RF Modem and command terminal. The status of your radio includes Advanced Features Tone. 5 Release the PTT button to receive. You hear a Transmit End up solid RED while transmitting. Talk into the microphone clearly if needed. 4 Press and hold the PTT button to transmit. The LED lights hear the volume set tone. Adjust the Volume Control knob if necessary. Release the Volume Set button. OR At the desired Fireground zone and channel, press the preprogrammed Monitor button and listen for activity. Adjust the Volume Control knob if necessary. OR If your radio is working in Fireground Zone Channel, proceed to next step. 3 Press and hold the preprogrammed Volume Set button to necessary. 2 Listen for a transmission. Adjust the Volume Control Knob if English 72 Advanced Features Evacuation Tone from full volume. OR Perform any action on the radio other than volume adjustments to cancel the evacuation indications and update the command terminal. OR If preprogrammed with Manual Acknowledgement of Evacuation Command, press the PTT button shall cancel the indications and acknowledge the command terminal. 2 Moving the volume knob to adjust the volume of the maximum alert tone volume level. The display shows EVACUATE. 1 Your radio sounds the Evacuation Tone at the profile’s Procedure: When Incident Commander triggers Evacuation signal from his command terminal, the RF Modem updates everyone in the Fireground Communication System with the order to evacuate the incident site. Responding to Evacuation Indicator Press PTT button to transmit.Talk clearly into the microphone. Release PTT button to listen. OR Receive and listen to call, the radio displays the caller’s name or ID. 1 At TPS Zone Channel Procedure: TPS enabled the users of a group to identify a transmission starts and ends clearly by displaying the caller’s name or ID on the radio display. Using TPS Normal Transmission Tactical Public Safety (TPS) (Conventional Only) cancel Emergency Beacon. 73 English 4 Long press Emergency button to exit Emergency mode and Sidetone. After a short pause, you hear Emergency Beacon. 3 Release to listen. You hear Emergency Call De-Key 2 Press PTT button to make Emergency Call. You hear Emergency Beacon. 1 Press the Emergency button to enter Emergency Mode. Procedure: Emergency Call De-Key Sidetone – The radio sounds an alert tone to remind radio user that the Emergency Mode is still active after user releases the PTT button for an Emergency call transmission. The volume of the tone depends on the maximum tone selected by your radio profile. Emergency Beacon – During Emergency if the TPS radio user pushes the Emergency button, the radio sounds a Beacon at the maximum volume of the radio at radio’s internal speaker and it is not adjustable. This beacon goes to silent when user presses the PTT button for voice transmission. Using TPS Emergency Transmission Advanced Features This feature could be preprogrammed for all channels that support Emergency feature or could be preprogrammed specifically to a zone and channel which has Emergency feature. Consult your agent or qualified technician for more details. It is recommended that an Emergency button is preprogrammed in order to allow the user to exit the emergency condition. The Man Down feature provides a Clear function to the user. After a Man Down condition has been detected, the user can press a preprogrammed Clear button or preprogrammed Menu Note: Your radio automatically activates Emergency Alarm or Call when the radio achieves or passes a tilt angle threshold or a combination of the angle threshold and radio motion below the motion sensitivity level, depending upon how the radio is programmed. The radio must stay in this condition for a preprogrammed amount of time before the Emergency Alarm or Call is activated. Note: Man Down feature is an alternate way to activate the Emergency feature if Emergency has been programmed in your radio. Man Down condition is determined based upon the radio tilt angle or a combination of radio tilt angle and the lack of radio motion. Man Down English 74 Advanced Features The radio senses the Man Down condition and Pre-Alert Timer is initiated. Man Down condition continues for the time duration defined in the Pre-Alert Timer field. At the end of this time, the radio alerts the user on the Man Down status with an audible alert tone and Man Down text on the screen. The Post-Alert Timer also initiates at this point. Man Down condition continues for the time duration defined in the Post-Alert Timer field. Once the timer expires, the Emergency alarm is transmitted. The Man Down Clear function is used in this phase to cancel the Man Down condition. stops and resets the timers. • Repositioning the radio exits the Man Down feature, which timers. • Pressing other buttons on the radio does not impact these releasing the PTT button reinitiates the Pre-Alert Timer. • Pressing the PTT button suspends the Man Down timers; The following scenarios affect the timers: iii ii The Man Down feature has three phases: Select button to cancel the Man Down condition. The radio remains in the Man Down state without triggering an emergency condition until the radio is moved out of the Man Down state, at which point Man Down functionality resumes. Note: When the radio is programmed with Man Down feature, special care is required when charging the radio with a wall mounted charger. See Handling Your Radio on page 163 for details. If the radio is preprogrammed to horizontal only, it must be worn in a vertical position otherwise the Man Down alert may be inadvertently triggered. Emergency must be set up for this feature to operate. For details on operating the Emergency alerts, please see Emergency Operation on page 67. Select button preprogrammed for Clear stops and resets the timers. The timers do not restart until the radio is repositioned. • Pressing a preprogrammed Clear button or pressing a Menu 75 English See Exiting Man Down Feature on page 77 to exit Man Down feature. This timer sets the amount of time the radio needs to remain in the Man Down condition before the Emergency alarm is transmitted. When the Post-Alert Timer is initiated, the radio alerts the user with an audible tone and displays the “ManDown” text. Post-Alert Timer The Pre-Alert timer reinitiates when the radio detects it is in the horizontal position or motionless again. When the radio detects that it has returned to the vertical position or when the radio detects motion, the Pre-Alert timer stops and is reset. This timer sets the amount of time that a Man Down condition must be present before the radio-user is warned of the Man Down condition. Pre-Alert Timer Advanced Features If the radio is programmed in Surveillance Mode, the radio inhibits all tones and lights on the radio including the Man Down tones. If the radio is programmed with Silent Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature. Note: At this point the Man Down features is complete. Use normal Emergency procedures to cancel Emergency transmissions. When the user does not clear the Man Down condition and the Post-Alert Timer comes to an end, Emergency Alarm or call is triggered. The radio sends emergency message to units within the same Talkgroup. The radio also sends ID number and GPS coordinates to dispatcher if these features are enabled. User can exit Emergency following the Emergency procedure. See Emergency Operation on page 67 for details. Triggering Emergency Note: The Man Down alert tone volume is directly related to the radio’s volume. Ensure that the radio’s volume is loud enough so that the user does not miss the Post-Alert tone. Triggered Alerting User When Man Down Feature is English 76 Advanced Features Consult your agent or qualified technician for more details. The volume and repetition duration of Man Down Enhanced alert tone could be customized and preprogrammed to suite the required situation. This feature is to be preprogrammed specifically to a zone and channel which supports Emergency feature. If the radio is programmed in Surveillance Mode, the alert tone can be heard from the radio speaker. If the radio is programmed with Silent Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature. is inhibited. • To a channel without Emergency feature – The alert tone Once the alert tone is active, changing to another channel with different setup triggers different response from the radio. Note: When the radio initiates Man Down Enhanced, you hear the Critical Man Down Continuous alert tone from the radio speaker. The volume of this tone is preprogrammed to a minimum level or to the current radio speaker level. Whichever louder is applied. This can act as a beacon to find the radio. Note: Triggered Alerting User When Man Down Enhanced is After exiting the Emergency Operation when the radio is still in Man Down condition (tilted achieving threshold angle or motionless), user must first exit Man Down condition to then reinitiate the Man Down feature. Re-Initiating Man Down Repositioning the radio or shaking the radio (when motion sensitivity is enabled). OR Press the preprogrammed Man Down Clear button to exit. OR Press the Menu Select Button below Clr to exit. Procedure: If you are not in a real Man Down situation, you should exit the Man Down feature and prevent emergency from going off with the following operation. Exiting Man Down Feature configuration – The alert tone continues. Enable the Emergency feature with Silent Alarm disabled, but not in Surveillance Mode before running this test on the radio. 77 English OR If no tone is heard, make sure that the Man Down feature is enabled on your radio. If Man Down feature was not enabled, please enable it and go through steps 1,2 and 3 again. OR If the Man Down feature is enabled and no tone is heard, send the radio to a qualified technician. 4 The radio alerts with audible tone and displays Man-Down. 3 Wait for alert tone. 2 Lay the radio down in the horizontal position. least 5 seconds. 1 Turn the radio on and place in the vertical position, for at When Man Down is enabled on the radio: Procedure: Note: Testing the Man Down Feature • To a channel with Emergency and similar Man Down configuration – The current alert tone is inhibited and replaced with a different alert tone. Return the radio to the vertical position OR Shake the radio (when motion sensitivity is enabled). Procedure: • To a channel with Emergency and different Man Down The alert tone is inhibited. • To a channel with Emergency but no Man Down feature – Advanced Features Note: The default ARS mode can be changed by a qualified radio technician using the radio’s programming software. • ARS Non-Server Mode • ARS Server Mode (default mode) The Automatic Registration Service for the radio consists of two (2) modes: Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Automatic Registration Service (ARS) Advanced English 78 Advanced Features 5 Press Sel to confirm the displayed channel. server channel. OR In ARS Non-Server Mode, the display shows the zone and ARS non-server channel. OR If the channel or mode selected is unprogrammed, the display shows Unprogrammed. Repeat Step 3. 4 In ARS Server Mode, the display shows the zone and ARS 3 U or D to the required channel or mode. display shows the current channel name. 2 Press the Menu Select button directly below Chan. The 1 < or > to Chan. Procedure: Turn the preprogrammed 16-Position Select knob, once the zone you want is displayed, to the desired mode. OR Follow the procedure below. Selecting or Changing the ARS Mode A predefined username that’s set more than the maximum allowed characters is an invalid name. directly below Edit to enter ID. A blinking cursor appears on the screen. Use the keypad to type or edit a username. 4 U or D to {ID Entry} and press the Menu Select button 3 The display shows the User Login screen. 2 Press the Menu Select button directly below User. 1 < or > to User. Procedure: Press the preprogrammed User Login button and proceed to Step 3. OR Follow the procedure below. Logging In as a User Note: You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. This feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username. Accessing the User Login Feature 79 English Indicator icon, the ID, and In progress, with Cncl. OR In ARS Non-Server Mode, the display shows the User Login 7 In ARS Server Mode, the display shows the User Login 6 Press the Menu Select button directly below Logn. Repeat Step 4. OR Enter your Personal Identification Number (PIN) number. 5 If the ID is invalid, the display shows momentary Invalid ID. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Press the Menu Select button directly below Ok to submit. OR U or D to scroll through the list of predefined usernames. Press the Menu Select button directly below Sel to select the predefined username. OR Press and hold U or D to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined username. Advanced Features failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed. Repeat Step 4. OR If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed. Repeat Step 4. OR Press the Menu Select button directly below Cncl to cancel the login in progress screen and return to the initial user login screen. OR Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and Logged in, with Logt and Exit. 8 If the username is invalid, login fails and the user login Indicator icon, the ID, and Logged in, with Logt and Exit. OR In non-ARS enabled mode, the display shows Offline, with Logt and Exit. English 80 Advanced Features Note: Private data refers to all messages in the text messaging inbox, Draft, and Sent folder. The next user is able to access the Inbox, Draft and Sent messages if private data is not deleted. momentary Private data cleared. OR Select No to keep your private data. 3 Select Yes to clear all your private data. The display shows OR If the Delete Messages On Session End feature is enabled, the radio clears the private data and returns to User Login screen. 2 The display shows Clear private data?. Go to step 3. 1 Press the Menu Select button directly below Logt. Procedure: When you have logged in or you are using Offline mode, you can log out. Logging Out Note: • Sent • Drafts See Status Icons on page 20 for more information on the TMS icons and TMS Menu Options on page 26 for more information on each menu option. 3 U or D to scroll through the main menu options. the TMS feature screen. 81 English 2 Press the Menu Select button directly below TMS to access • Compose 1 < or > to TMS. • Inbox Query is only supported withing ASTRO 25 Advanced Messaging Solution. See Two-Factor Authentication on page 93 and ASTRO 25 Advanced Messaging Solution on page 92 for details. Press the Menu Select button directly below Back at any time to return to the previous screen. The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen. OR Press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox. OR Follow the procedure below. Note: Accessing the Messaging Features The main menu consists of the following options: Note: • A query (ASTRO 25 Advanced Messaging Solution). • An edited quick text message. • A predefined message (quick text message). • A new text message (free form message). The types of text messages available: This features allows you to quickly send and receive messages and run database queries directly from your radios. Text Messaging Service (TMS) Advanced Features During the numeric mode, except for 1, pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap). During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. 5 A blinking cursor appears on the Compose screen. button directly below Sel to compose a new message. 4 U or D to Text Message and press the Menu Select directly below Sel. OR Press the Menu Select button directly below Exit to return to the Home screen. 3 U or D to Compose and press the Menu Select button the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Procedure: Note: Composing and Sending a New Text Message English 82 Advanced Features required address. OR U or D to {Other Recpnt} and press the Menu Select button below Edit. A blinking cursor appears on the Enter Address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 8 U or D to scroll through the address list and highlight the button directly below Sel. 7 U or D to Send Message and press the Menu Select message is composed. 6 Press the Menu Select button directly below Optn once the Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. You can also select the Save to Drafts option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 89 for more information. 83 English Menu Select button directly below Sel to select the required message. 5 U or D to scroll through the list of messages and press the directly below Sel for a predefined message. 4 U or D to Quick Text and press the Menu Select button directly below Sel. OR Press the Menu Select button directly below Exit to return to the Home screen. 3 U or D to Compose and press the Menu Select button the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 85 for more information. If the message fails to send, the radio returns you to the main TMS screen. Each Quick Text message or Query has a maximum length of 50 characters. You can select the required text from the Quick Text or Query. Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. Sending a Quick Text Message Procedure: Press the preprogrammed Quick Text button and proceed to Step 4. OR Follow the procedure below. shows Msg sent. OR If the message is not sent, you hear a low tone and the display shows Send failed. 11 If the message is sent, you hear a tone and the display Sending msg. 10 The display shows the Send Message screen and button to send the message. 9 Press the Menu Select button below Send or the PTT Advanced Features required address. OR U or D to {Other Recpnt} and press the Menu Select button below Edit. A blinking cursor appears on the Enter Address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. 9 U or D to scroll through the address list and highlight the button directly below Sel. 8 U or D to Send Message and press the Menu Select 7 Press the Menu Select button directly below Optn. blinking cursor at the end of it. Use the keypad to edit the message, if required. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 The message appears on the Compose screen, with a English 84 Advanced Features Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 85 for more information. If the message fails to send, the radio returns you to the main TMS screen. shows Msg sent. OR If the message is not sent, you hear a low tone and the display shows Send failed. 12 If the message is sent, you hear a tone and the display Sending msg. 11 The display shows the Send Message screen and button to send the message. 10 Press the Menu Select button below Send or the PTT Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. The Priority Status icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important. icon on the label bar. 3 The priority status icon appears beside the normal message button directly below Sel to indicate the message as important. 2 U or D to Mark Important and press the Menu Select 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: Note: Appending a Priority Status to a Text Message Before sending your message, you can append a priority status and/or a request reply to your message. Features Using the Priority Status and Request Reply icon on the label bar. 85 English 3 The request reply icon appears beside the normal message directly below Sel to request for a reply. 2 U or D to Req Reply and press the Menu Select button 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: Appending a Request Reply to a Text Message bar. 3 The display shows the normal message icon on the label button directly below Sel to remove the priority status from the message. 2 U or D to Mark as Normal and press the Menu Select 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: Removing a Priority Status from a Text Message Advanced Features button directly below Sel to indicate the message as important. AND 2 U or D to Mark Important and press the Menu Select 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: to a Text Message Appending a Priority Status and a Reply Request bar. 3 The display shows the normal message icon on the label directly below Sel to remove the priority status from the message. 2 U or D to No Req Reply and press the Menu Select button 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: Removing a Request Reply from a Text Message English 86 Advanced Features bar. 3 The display shows the normal message icon on the label button directly below Sel to indicate the message as important. AND U or D to No Req Reply and press the Menu Select button directly below Sel to request for a reply. 2 U or D to Mark as Normal and press the Menu Select 1 Press the Menu Select button directly below Optn. After the outgoing message is composed (see Composing and Sending a New Text Message on page 82 for more information): Procedure: from a Text Message Removing a Priority Status and a Reply Request the normal message icon on the label bar. 3 The priority status and request reply icons appear beside directly below Sel to request for a reply. U or D to Req Reply and press the Menu Select button When you receive a message that is flagged with the “Request Reply” icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message. the latest received message on top. 3 The display shows a list of aliases or IDs, with the sender of the Inbox. 2 Press the Menu Select button directly below TMS to access momentary New msg. 1 The new message icon appears and the display shows Procedure: When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and go to Step 3. OR Follow the procedure below. Note: Receiving a Text Message Managing Text Messages screen. U or D to read the message if fills more than one Select button below Sel to view the message. 87 English 5 U or D to the required aliases or ID and press the Menu the latest received message on top. 4 The display shows a list of aliases or IDs, with the sender of Sel. 3 U or D to Inbox and press the Menu Select button below the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and proceed to Step 4. OR Follow the procedure below. Note: The Inbox can hold up to thirty (30) messages. Viewing a Text Message from the Inbox Advanced Features The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 25 for more information. The original date and time stamp, address and message content is automatically appended to the reply message. button directly below Sel. OR U or D to Quick Text and press the Menu Select button directly below Sel for a predefined message. OR 3 U or D to Text Message and press the Menu Select a message. 2 Press the Menu Select button directly below Rply to reply to Select button below Sel to view the message. 1 U or D to the required aliases or ID and press the Menu Procedure: Note: Replying to a Received Text Message Note: • Select Back to return to the previous screen. • Select Del to delete the message. • Select Optn to configure the message settings. While on the view message screen, press the Menu Select button directly below Optn, Del, or Back to access the option. English 88 Advanced Features Press the Menu Select button directly below Back at any time to return to the previous screen. Sending msg. 8 The display shows the Send Message screen and button directly below Sel to send the message. 7 U or D to Send Message and press the Menu Select have finished writing the message. 6 Press the Menu Select button directly below Optn once you Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 5 Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. OR The predefined message appears on the Compose screen, with a blinking cursor at the end of it. 4 A blinking cursor appears on the Compose screen. Menu Select button directly below Sel to select the required message. U or D to scroll through the list of messages and press the You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 85 for more information. • Select Del to delete the message. • Select Edit to edit the message before sending it. Press the Menu Select button directly below Edit, Del., or Back to access the option. button below Sel to view the message. 5 U or D to the required text message press the Menu Select message drafted on top. 4 The display shows a list of drafts, with the latest text Sel. 3 U or D to Drafts and press the Menu Select button below the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Procedure: This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Accessing the Drafts Folder Note: Sel. 89 English 3 U or D to Sent and press the Menu Select button below the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Follow the procedure below. Procedure: Viewing a Sent Text Message The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest message in the folder is deleted when the 11th message comes in. Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list. Managing Sent Text Messages • Select Back to return to the previous screen. Advanced Features Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 25 for more information. • Select Back to return to the previous screen. • Select Del to delete the message. • Select Optn to configure the message settings. While on the view message screen, press the Menu Select button directly below Optn, Del, or Back to access the option. Select button below Sel to view the message. 5 U or D to the required aliases or ID and press the Menu of latest sent message on top. 4 The display shows a list of aliases or IDs, with the recipient English 90 Advanced Features button to send the message. 4 Press the Menu Select button below Send or the PTT required address. OR U or D to {Other Recpnt} and press the Menu Select button below Edit. A blinking cursor appears on the Enter Address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 3 U or D to scroll through the address list and highlight the button directly below Sel. 2 U or D to Send Message and press the Menu Select viewing the message. 1 Press the Menu Select button directly below Optn while Procedure: Sending a Sent Text Message You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 85 for more information. the current message. 2 Press the Menu Select button directly below Del to delete 1 U or D to scroll through the messages. From the Inbox, Draft, or Sent screen: Procedure: Deleting a Text Message Note: Press the Menu Select button directly below Back at any time to return to the previous screen. Sending msg. 5 The display shows the Send Message screen and 91 English all the messages in the selected folder. OR Press the Menu Select button directly below No to return to the main TMS screen. 5 Press the Menu Select button directly below Yes to delete 4 The display shows Del All?. button below Clr to select all messages in the selected folder. 3 U or D to Inbox or Sent then press the Menu Select the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Press the preprogrammed Data Feature button or the TMS Feature button to access the Messaging feature screen, and proceed to Step 3. OR Follow the procedure below. Procedure: Deleting All Text Messages Advanced Features • New Service Advertisement for service availabilities • TMS for messaging TMS functionality splits between two protocols: • New User Authentication for User Login • ARS for Device Registration With this Advanced Messaging Solution, ARS functionality splits between two protocols: With Query and Two-Factor Authentication, you can use a secure system logon to initiate and receive key information on people, vehicles and properties when doing the regular security patrol. You can access to local or external databases such as the National Crime Information Center (NCIC), for "Hot Hits" on priors and warrants. Query and Two-Factor Authentication has Criminal Justice Information Services (CJIS) security compliance for queries. The ASTRO 25 Advanced Messaging Solution allows you to quickly send and receive messages and run database queries directly from your data-enabled Motorola two-way radios. Federal mandate requires Two-Factor Authentication when querying Federal and State databases. With this advance messaging solution you have the ability enable Two-Factor Authentication. ASTRO 25 Advanced Messaging Solution English 92 Advanced Features Note: Power loss and power down are different activities, power down occurs when the user intentionally powers off the radio, power loss is when the battery dies or is removed from the unit. The radios caches the user name, unit ID and or Single Factor password in the codeplug, this allows the radio to automatically log in to use Single Factor authentication upon power up or mode change. The Two-Factor passcode is not stored in the codeplug. You can upgrade the Single Factor session to a TwoFactor session by entering the Two-Factor passcode only. After an interruption (for example mode change, DSR switch over, power loss) the radio is capable of restoring the active session in its current state as long as the session is active in the server. Your user name, unit ID and password all need to be provisioned in PremierOne™. Your user account in PremierOne needs to be linked to an RSA account specifying a token to be used with the Two-Factor passcode. Solution System Setup for ASTRO Advanced Messaging The radio with Two-Factor capabilities are backward compatible with the existing device registration system and TMS servers. Note: A predefined username that’s set more than the maximum allowed characters is an invalid name. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. Secondly, this feature supports query authentication requirements so the query service knows which user originated a query. 93 English directly below Edit. A blinking cursor appears. Use the keypad to type or edit a username. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Press the Menu Select button directly below Ok to submit. OR U or D to scroll through the list of predefined usernames. Press the Menu Select button directly below Sel to select the predefined username. OR 4 U or D to {ID Entry} and press the Menu Select button 3 The display shows the User Login screen. 2 Press the Menu Select button directly below User. 1 < or > to User. Procedure: Press the preprogrammed User Login button and proceed to Step 3. OR Follow the procedure below. Two-Factor Authentication is an extension of existing ARS and TMS operation. This feature allows you to authenticate yourself with a username, unit ID, password and passcode. The purpose of this feature is to allow the sender of a text message to address a specific user of the radio, so the message is delivered to the user, not to the radio which may have any user using it at the time. Logging into Two-Factor Authentication Two-Factor Authentication Advanced Features maximum allowed characters, or an invalid character in it, 7 If the selected predefined Unit ID has more than the directly below Edit. A blinking cursor appears. Use the keypad to type or edit a Unit ID. Press the Menu Select button directly below Ok to submit. OR U or D to scroll through the list of predefined Unit IDs. Press the Menu Select button directly below Sel to select the predefined Unit ID. OR Press and hold U or D to scroll through the list of predefined Unit IDs at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined Unit ID. 6 U or D to {UnitID Entry} and press the Menu Select button maximum allowed characters, or an invalid character in it, the display shows momentary Invalid ID. Repeat Step 4. OR For radio enabled with Unit ID, proceed to step 6 to enter your Unit ID. OR Use the keypad to enter your password and proceed to step 8. 5 If the selected predefined username has more than the Press and hold U or D to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined username. English 94 Advanced Features failed. The display shows User Login screen with 1F logged in status. Press the Menu Select button directly below Pscd to repeat step 9. OR The display shows User Login screen with 2F logged in status to indicate Two-Factor Authentication complete. 11 If the login fails, the display shows momentary 2F pscd display shows In progress. 10 Press the Menu Select button directly below Logn. The in status. The login operation is complete. OR If login fails, the display shows momentary Login failed. The display returns to User Login screen. Repeat Step 4. OR For radio enabled with two-factor login, a blinking cursor appears. Enter your passcode. 9 If only one-factor is enabled, the display shows 1F logged 8 Press the Menu Select button directly below Logn or Ok. the display shows momentary Invalid UnitID. Repeat step 6. OR A blinking cursor appears. Enter your password. Private data refers to all messages in the text messaging Inbox, Draft, and Sent folder. The next user is able to access the Inbox, Draft and Sent messages if private data is not deleted. Radio which is successfully logged into the secured system receives advertisement from the server that the access to the data for query is enabled. Note: Note: momentary Private data cleared. OR Select No to keep your private data. 3 Select Yes to clear all your private data. The display shows OR If the Delete Messages On Session End feature is enabled, the display shows momentary Private data cleared. 2 The display shows Clear private data?. The query server must be selected as the destination so that it can receive the query message and respond the query with text message. The query server must be an entry in the data user list in the CPS. directly below Sel. OR 95 English 3 U or D to Compose and press the Menu Select button the TMS feature screen. 2 Press the Menu Select button directly below TMS to access 1 < or > to TMS. Procedure: Press the preprogrammed TMS Query button and proceed to Step 5. OR Follow the procedure below. Note: You shall receive a service advertisement message to indicate the Query is available after you have successfully logged in the radio with a Two-Factor Authentication. This feature is available for radio users who have successfully logged in with the Two-Factor Authentication. Query is a special form of Quick Text marked with a flag that is replied or dispatched in normal TMS message. The query template needs to be configured in the quick text list of the CPS. You can choose from the quick text list, including queries if present. Procedure: 1 Press the Menu Select button directly below Logt. Sending a Query Logging out of Two-Factor Authentication Advanced Features required address. OR 9 U or D to scroll through the address list and highlight the button directly below Sel. 8 U or D to Send Message and press the Menu Select 7 Press the Menu Select button directly below Optn. blinking cursor at the end of it. Use the keypad to edit the message, if required. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 The message appears on the Compose screen, with a Menu Select button directly below Sel to select the required message. 5 U or D to scroll through the list of messages and press the below Sel for a predefined message. 4 U or D to Query and press the Menu Select button directly Press the Menu Select button directly below Exit to return to the Home screen. English 96 Advanced Features Note: The server responds to your query with the required report in text messages. If the message fails to send, the radio returns you to the main TMS screen. shows Msg sent. OR If the message is not sent, you hear a low tone and the display shows Send failed. 12 If the message is sent, you hear a tone and the display Sending msg. 11 The display shows the Send Message screen and button to send the message. 10 Press the Menu Select button below Send or the PTT U or D to {Other Recpnt} and press the Menu Select button below Edit. A blinking cursor appears on the Enter Address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. the latest received message on top. 3 The display shows a list of aliases or IDs, with the sender of the TMS Feature button to access the Inbox and go to Step 3. OR Press the Menu Select button directly below TMS to access the Inbox. 2 Press and hold the preprogrammed Data Feature button or shows the message icon flagged with “Priority”. The display shows momentary New msg. 1 You hear an unique, high-pitched chirp and the display Procedure: You shall received the information you have requested in TMS format. Receiving a Query You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 85 for more information. On the APX 7000L, only AES encryption is supported for secure LTE data. In addition, for secure LTE data a Virtual Private Network (VPN) is required. Note: 97 English The radio will not transmit until you set the Secure/ Clear switch to the clear position. If the selected channel is preprogrammed for clear-only operation – when you press the PTT button, you hear an invalid mode tone and the display shows Clear TX only. Procedure: Turn the preprogrammed Secure/Clear switch to the secure position. Selecting Secure Transmissions Note: Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Secure Operations Advanced Features The radio can be configured to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details. The radio will not transmit until you set the Secure/ Clear switch to the secure position. If the selected channel is preprogrammed for secureonly operation – when you press the PTT button, you hear an invalid mode tone and the display shows Secure TX only. Refer to the key-variable loader (KVL) manual for equipment connections and setup. 1 Attach the KVL to your radio. Procedure: Note: Loading an Encryption Key Managing Encryption Note: Procedure: Turn the preprogrammed Secure/Clear switch to the clear position. Selecting Clear Transmissions English 98 Advanced Features short tone for single-key radios. OR When the key has been loaded successfully, you hear an alternating tone for multikey radios. 4 When the key has been loaded successfully, you hear a directly below LOAD on the KVL. This loads the encryption keys into your radio. 3 Select the required keys and press the Menu Select button functions, except for power down, backlight, and volume, are locked out. 2 The display shows Keyloading, and all other radio conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure. • Trunked Multikey – If you use your radio for both (strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operatorselectable keys, operator-selectable keysets, and operatorselectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. • Conventional Multikey – The encryption keys can be tied Note: 99 English When the selected key is erased, you hear a momentary keyfail tone and the display shows Key fail. OR When the selected key is not allowed, you hear a momentary short, low-pitched tone and the display shows Illegal key. newly selected key and return to the Home screen. OR Press H, the PTT button, or the Menu Select button directly below Exit to exit. OR Turn the 16-Position Select knob to exit. 4 Press the Menu Select button directly below Sel to save the OR Use the keypad to enter the number of the desired key. 3 U or D to scroll through the encryption keys. display shows the last user-selected and stored encryption key, and the available menu selections. 2 Press the Menu Select button directly below Key. The 1 < or > to Key. Procedure: This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types: Selecting an Encryption Key Using the Multikey Feature Advanced Features Press H, the PTT button, or the Exit menu selection, or turn the 16-Position Select knob to exit this menu at any time without changing the keyset selection. newly selected keyset. 4 Press the Menu Select button directly below Sel to save the OR Use the keypad to enter the number of the desired keyset. 3 U or D to scroll through the keysets. display shows the last user-selected and stored keyset, and the available keyset menu selections. 2 Press the Menu Select button directly below KSet. The 1 < or > to KSet. Procedure: Note: Every channel to which one of the original keys was tied now has the equivalent new key instead. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other. This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. Selecting a Keyset English 100 Advanced Features At Erase single key?, press the Menu Select button below Yes to erase all the encryption keys in the radio OR No to return to the previous screen. OR 6 At Erase all keys?, press the Menu Select button directly button directly below Sel. 5 U or D to the required option and press the Menu Select display shows the available key erase options. 4 Press the Menu Select button directly below Optn. The OR Use the keypad to enter the number of the desired key. 3 U or D to the desired encryption key. display shows the last user-selected and stored encryption key, and the available menu selections. 2 Press the Menu Select button directly below Eras. The 1 < or > to Eras. Procedure: This feature allows you to erase all or selected encryption keys. Erasing the Selected Encryption Keys screen. 5 The radio exits keyset selection and returns to the Home Note: DO NOT press the Top (Orange) button before pressing the Top Side (Select) button, unless you are in an emergency situation as this sends an emergency alarm. shows All keys erased. 4 When all the encryption keys have been erased, the display 3 The display shows Please wait. (Orange) button. 2 While holding Top Side (Select) button down, press the Top 1 Press and hold the Top Side (Select) button. 1 < or > to Reky. Use the preprogrammed Top Side (Select) button and Top (Orange) button to erase the single key in radios with the single-key option, and to erase all keys in radios with the multikey option. Note: 101 English Refer to your local key management supervisor for more information. The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. tone and the display shows Rekey fail. 4 If the rekey operation fails, you hear a short, low-pitched OR Press the PTT button again, or the Home or Emergency button, to exit the feature and transmit in normal mode. 3 Press the PTT button to send the rekey request. 2 Press the Menu Select button directly below Reky. Procedure: This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Conventional Only) Requesting an Over-the-Air Rekey (ASTRO OR below Exit to exit. OR Turn the 16-Position Select knob to exit. 7 Press H, the PTT button, or the Menu Select button directly directly below Yes to erase the displayed encryption key OR No to return to the previous screen. Advanced Features This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all of the encryption keys is erased. Without this UKEK key, the radio could not be over the air rekeyed. Infinite UKEK Retention Note: Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly. There are two components of Hear Clear. This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgments, and Powerup Acknowledgments. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. The Random FM Noise Canceller operates only in receive mode. Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. 2 Random FM Noise Canceller (Flutter Fighter): remains the same at receiving radio. • Expander – expands the speech while the noise flow speech signal at transmitting radio. • Compressor – reduces the background noise flow and the Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. 1 Companding: Hear Clear MDC Over-the-Air Rekeying (OTAR) Page English 102 Advanced Features OR 3 If the password is correct, the radio unlocks. code. OR Press the Menu Select button directly below Del to delete any unwanted characters. OR Press the Menu Select button directly below Cncl to exit the feature. 2 Press the Menu Select button directly below Sel to enter the Secure-equipped radios – 6 to 8 characters. Clear radios – 0 to 8 characters. 1 Enter your numeric password. Procedure: Unlocking Your Radio If this feature is enabled in your radio by a qualified radio technician, when you turn the radio on, the display shows Radio locked. This feature changes your radio to a more robust security system that protects the use of the secure encryption keys. Radio Lock Security 5 Enter the old password. 4 Press the Menu Select button directly below Sel. 3 U or D to Unlock Pswd. display shows Change Password screen. 103 English 2 Press the Menu Select button directly below Pswd. The 1 < or > to Pswd. Procedure: Changing Your Password If you forget the password, enter ******** to erase all keys and revert the password in the radio back to the default password of 01234567. IMPORTANT: For Secure Radios Only – After a total of 17 consecutive incorrect passwords (turning the radio off and on does not reset this number), the radio erases all of its encryption keys and shows Deadlock. See a qualified radio technician. If you enter three incorrect passwords in a row, the display shows Deadlock. Turn the radio off and then on, and begin again at Step 1. If the password is incorrect, the display show Incorrect password and the radio remains locked. Advanced Features 1 < or > to Pswd. 2 Press the Menu Select button directly below Pswd. The 8 Press the Menu Select button directly below Sel. 9 Re-enter the new password. Note: If you enter three incorrect old passwords, the radio exits the password feature. You cannot access this feature again until you turn the radio off and on. password is updated. OR If the two passwords do not match, repeat Steps 5 through 8. Note: If you enter three incorrect old passwords, the radio exits the password feature. You cannot access this feature again until you turn the radio off and on. password is updated. OR If the two passwords do not match, repeat Steps 5 through 8. 10 Press the Menu Select button directly below Sel. The 9 Re-enter the new password. 8 Press the Menu Select button directly below Sel. 7 Enter the new password. 6 Press the Menu Select button directly below Ok. 5 Enter the old password. 4 Press the Menu Select button directly below Sel. 3 U or D to Tactical Inh Encode Pswd. display shows Change Password screen. Procedure: 7 Enter the new password. 10 Press the Menu Select button directly below Sel. The Changing Your Tactical Inhibit Password 6 Press the Menu Select button directly below Ok. English 104 Advanced Features feature is enabled. OR Display shows Pswd disabled, indicating that the radio lock feature is disabled. 3 Display shows Pswd enabled, indicating that the radio lock 2 Press the Menu Select button directly below Logf. 1 < or > to Logf. Procedure: This feature allows you to enable or disable the radio lock feature. It is programmable by a qualified radio technician. (Secure Radios Only) Enabling or Disabling the Radio Lock Feature 105 English OR Press the Menu Select button directly below LNum to go to the last number dialed. OR Use the keypad to enter the required ID. OR 5 U or D to the required ID. shows radio Contact IDs. 4 Press the Menu Select button directly below Ok. The display Password. 3 Use the keypad to enter your Tactical Inhibit Encode display shows Enter Password. 2 Press the Menu Select button directly below Stun. The Using Radio Stun 1 < or > to Stun. This feature allows you to stun another radio by sending an over the air command using the menu on your radio. This feature prevents an unauthorized user from using the radio. Once the radio is stunned, a password is required to re-activate the stunned radio. Using Radio Stun Radio Stun and Kill Advanced Features The killed radio can only be recovered from KILL with a special device. Consult an authorized and qualified technician for details. This feature allows you to render your radio or another radio inoperable if the radio is misplaced or lost. When a radio is killed, the display turns blank and all functions of the radio are not usable. Using Radio Kill Once the receiving radio received the command, its screen locked and request for password. To un-stun a radio, follow the procedure in Unlocking Your Radio on page 103. decrypt the received the command, your radio display shows Ack received. OR If the receiving radio does not encryption key to decrypt the received encrypted command, your radio display shows Decrypt failed. OR If the receiving radio is powered off, your radio display shows No Acknowledgment. 6 If the receiving radio does not have encryption key to Press the Menu Select button directly below Send to initiate command. English 106 Advanced Features OR Press the Menu Select button directly below LNum to go to the last number dialed. OR Use the keypad to enter the required ID. OR Press the Menu Select button directly below Send to initiate command. 5 U or D to the required ID. shows radio Contact IDs. 4 Press the Menu Select button directly below Ok. The display Password. 3 Use the keypad to enter your Tactical Inhibit Encode display shows Enter Password. 2 Press the Menu Select button directly below Kill. The 1 < or > to Kill. Remote Kill allows you to render another radio inoperable by sending an over the air command using the menu on your radio. Using Remote Kill • Underground locations 107 English Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to: The GPS technology uses radio signals from earth orbiting satellites, to establish the location coordinates, maximizing your view of clear unobstructed sky is essential for optimum performance. 1 Press and hold Top Side Button then press the Orange button until the display turns blank and becomes inoperable. Understanding the GPS Feature For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. This feature uses information from the Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude or MGRS format per request from customer. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature. The Global Positioning System (GPS) Procedure: Direct Kill allows you to make your own radio inoperable. Using Direct Kill Once the receiving radio received the command, its screen turns blank, the killed radio is inoperable. display shows Ack received. OR If the receiving radio does not encryption key to decrypt the received encrypted command, your radio display shows Decrypt failed. OR If the receiving radio is powered off or already killed, your radio display shows No Acknowledgment. 6 If the receiving radio received the command, your radio Advanced Features Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes further away. Note: The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of Defense GPS user policy and the Federal Radio Navigation Plan. These changes may affect the performance of the GPS feature on your radio. Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites. Note: Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher. radio • In temperature extremes outside the operating limits of your • Between tall buildings or under dense tree-cover • Under any other metal or concrete roof or structure • Inside of buildings, trains, or other covered vehicles English 108 Advanced Features Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio. This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air. The Outdoor Location Feature (Using GPS) nothing between your radio and a large amount of open sky. • Stay in the open. The GPS feature works best where there is • For your initial fix, hold the radio in the face position. To maximize the ability of your radio to determine a fix, please note the following guidelines: Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. Enhancing GPS Performance This feature can only be enabled through CPS configuration. When the MGRS coordinate is enabled, all location coordinates are displayed in MGRS format, including the editable locations in GPS. Enabling MGRS Coordinates The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. Coordinates cannot be deleted. Coordinates can be deleted one at a time, or all at once. Note: The Home and Destination coordinates are editable. • Destination • Last Known Location • Emergency • Home Fixed location coordinates: Preprogrammed Waypoints Only the alias is editable, not the coordinates. User-configurable location coordinates. Programmable Waypoints The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator. location is being determined. 109 English 7 The top line temporarily displays Please wait while the new a new location fix. 6 Press the Menu Select button directly below Rfsh to obtain location, time and date of the last successful location fix. 5 The front display shows the MGRS or latitude/longitude location fix. OR Press the Menu Select button directly below Optn. U or D to Turn On GPS and press the Menu Select button directly below Sel. 4 Press the Menu Select button directly below On to obtain a 3 The display shows Location off. 2 Press the Menu Select button directly below Loc. 1 < or > to Loc. Procedure: Press the preprogrammed GPS button to toggle the Outdoor Location feature on or off. OR Follow the procedure below. Note: Accessing the Outdoor Location Feature Advanced Features The radio also exits the menu if the emergency button is pressed. feature and return to the main screen. OR Press H, the PTT button, or the preprogrammed GPS button to return to the Home screen. 9 Press the Menu Select button directly below Exit to exit the the current location along with the UTC (Zulu) time and date that the location fix was obtained. The location coordinates are updated automatically every five seconds while the location signal is present. OR If the radio fails to get a location fix, the display shows No service and returns to the previous display. 8 Once the location coordinates are fixed, the display shows While the new location is being determined, the location signal can be a solid or blinking icon. English 110 Advanced Features Use the keypad to edit the auto-generated waypoint, if required. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. OR 3 A blinking cursor appears in the Save As Waypt screen. button directly below Sel. OR U or D to Save as Home and press the Menu Select button directly below Sel and proceed to Step 5. OR U or D to Save as Dest. and press the Menu Select button directly below Sel and proceed to Step 5. 2 U or D to Save as Waypt and press the Menu Select 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Saving a Waypoint feature and return to the main screen. OR Press H, the PTT button, or the preprogrammed GPS button to return to the Home screen. 6 Press the Menu Select button directly below Exit to exit the name>. OR The display shows Current loc saved as {Home}. OR The display shows Current loc saved as {Destination}. 5 The display shows Current loc saved as to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 A blinking cursor appears in the Edit Name screen. directly below Sel. 5 U or D to Edit name and press the Menu Select button Select button directly below Optn. 4 U or D to the required saved waypoint, and press the Menu 3 The display shows a list of waypoints. directly below Sel. 2 U or D to Waypoints and press the Menu Select button 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Editing the Alias of a Waypoint English 112 Advanced Features Only the preprogrammed coordinates of Home and Destination are editable. below Optn. 4 U or D to {Home} and press the Menu Select button directly 3 The display shows a list of waypoints. directly below Sel. 2 U or D to Waypoints and press the Menu Select button 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Note: Editing the Coordinates of a Waypoint to the previous screen. OR Press H, the PTT button, or the preprogrammed GPS button to return to the Home screen. 9 Press the Menu Select button directly below Back to return radio returns to the Waypoints main screen. 8 The display shows Updated and the are done. OR Press the Menu Select button directly below Cncl to return to the Waypoints main screen. 7 Press the Menu Select button directly below Ok once you to the Waypoints main screen. OR 10 The display shows {Home} Updated and the radio returns are done with the new coordinates. 9 Press the Menu Select button directly below Ok once you are done. OR Press the Menu Select button directly below Cncl to return to the previous screen. 8 Press the Menu Select button directly below Ok once you Press the Menu Select button directly below Del to delete any unwanted characters. 7 A blinking cursor appears in the Edit Location screen. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Edit to change the number/coordinates. 6 The first number blinks. Press < to move to the previous number/coordinates. Press > to move back to the next number/coordinates. directly below Sel. 5 U or D to Edit Location and press the Menu Select button OR U or D to {Destination} and press the Menu Select button directly below Optn. 113 English before the radio returns to the Waypoints main screen. 7 The display shows momentary deleted the waypoint. OR Press the Menu Select button directly below No to return to the Waypoints main screen. 6 Press the Menu Select button directly below Yes to delete 5 The display shows Delete Confirm?. directly below Del. OR Press the Menu Select button directly below Del. U or D to Edit name and press the Menu Select button Select button directly below Optn. 4 U or D to the required saved waypoint, and press the Menu 3 The display shows a list of waypoints. directly below Sel. 2 U or D to Waypoints and press the Menu Select button 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Deleting a Single Saved Waypoint The display shows {Destination} Updated and the radio returns to the Waypoints main screen. Advanced Features You cannot delete any of the preprogrammed waypoints. deleted before the radio returns to the Waypoints main screen. 8 The display shows momentary All saved waypnts all waypoints. OR Press the Menu Select button directly below No to return to the Waypoints main screen. 7 Press the Menu Select button directly below Yes to delete 6 The display shows Delete All saved waypnts Confirm?. directly below Sel. 5 U or D to Delete All and press the Menu Select button button directly below Optn. 4 U or D to a saved waypoint, and press the Menu Select 3 The display shows a list of waypoints. directly below Sel. 2 U or D to Waypoints and press the Menu Select button 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Deleting All Saved Waypoints English 114 Advanced Features to the selected coordinates. 5 The display shows the distance and bearing from the current button directly below Sel. 4 U or D to the required waypoint, and press the Menu Select 3 The display shows a list of waypoints. directly below Sel. 2 U or D to Dist frm here and press the Menu Select button 1 Press the Menu Select button directly below Optn. Procedure: While in the current location display: Waypoint Measuring the Distance and Bearing from a Saved If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known Location waypoints, respectively. If you have turned Location off using the ON/OFF menu key, it automatically turns back on when Emergency is activated. However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated. When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the Home (default) screen so that you can see which channel the emergency signal is going out on. Mode Using the Location Feature While in Emergency 115 English When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. display shows Failsoft. 2 You hear a medium-pitched tone every 10 seconds and the in conventional operation on a predetermined frequency. 1 During failsoft operation, your radio transmits and receives Procedure: The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. Using the Failsoft System Trunking System Controls Advanced Features Note: When this occurs, you can communicate only with other radios within your trunking site. The display shows the currently selected zone/channel combination and Site trunking. If the zone controller loses communication with any site, that site reverts to site trunking. Using the Site Trunking Feature It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. 2 Your radio remains in this out-of-range condition until: AND/OR The display shows the currently selected zone/channel combination and Out of range. 1 You hear a low-pitched tone. Home screen. 4 The radio saves the new site lock state and returns to the the site. The display shows Site locked. OR Press the Menu Select button directly below Unlk to unlock the site. The display shows Site unlocked. 3 Press the Menu Select button directly below Lock to lock 2 Press the Menu Select button directly below Site. 1 < or > to Site. Procedure: Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. OR Follow the procedure below. This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. When your radio goes out of the range of the system, it can no longer lock onto a control channel. Procedure: Locking and Unlocking a Site Going Out of Range English 116 Advanced Features screen. 3 When the radio finds a new site, it returns to the Home Note: APX 7000L radio does not support Bluetooth Commercial of the Shelf (COTS) devices or the Personal Area Network (PAN) data profile. • Serial Port (SPP) • Personal Area Networking (PAN) • Dial Up Networking (DUN) 117 English • Headset (HSP) Scanning site. button. 2 You hear a tone and the display shows momentary Your radio must be preprogrammed to allow you to use this feature. Currently your radio supports the following Bluetooth devices or profiles. Note: The default setting for Bluetooth-enabled radio is Bluetooth ON. See Turning the Bluetooth Off on page 118 to turn the Bluetooth OFF. 1 Press and hold down the preprogrammed Site Displ/Srch Procedure: Changing the Current Site and its corresponding received signal strength indicator (RSSI). 2 The display shows momentary the name of the current site 1 Press the preprogrammed Site Displ/Srch button. Note: Procedure: It is recommended to use Motorola proprietary MCW devices with APX radios during Mission Critical operations as other Bluetooth devices may or may not meet the mission critical standard. This feature allows your radio to extend its functionality by connecting to external proprietary Motorola accessories. Mission Critical Wireless (MCW) - Bluetooth® - Viewing the Current Site This feature allows you to view the name of the current site or forces your radio to change to a new one. Viewing and Changing a Site Advanced Features APX 7000L only works with Motorola MCW devices. OR The display shows Bluetooth on failed to indicate Bluetooth has failed to launch. 2 You hear a short, medium-pitched tone. The display shows momentary Bluetooth on, and b appears. 1 Press the preprogrammed button to turn on the Bluetooth. OR to the Home screen. 3 Press the Menu Select button directly below Exit to return directly below On. The display shows Status On, and b appears. OR The display shows Bluetooth on failed to indicate Bluetooth fails to launch. 2 U or D to Status and press the Menu Select button BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Turning the Bluetooth On English 118 Advanced Features 2 You hear a short, medium-pitched tone. The display shows momentary Bluetooth off, and b disappears. 1 Press the preprogrammed button, to turn off the Bluetooth. OR to the Home screen. 3 Press the Menu Select button directly below Exit to return directly below Off. The display shows Status Off, and b disappears. 2 U or D to Status and press the Menu Select button BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Turning the Bluetooth Off device are turned off after pairing, keys are NOT lost. When the radio and the device are turned back on, they can resume the Bluetooth connection without user intervention. • Infinite – (For all Bluetooth devices.) When the radio and/or and/or device is turned off after pairing, the keys are lost. Due to this, when your radio and your device are turned back on, they are unable to re-connect. The user must re-pair the devices to re-establish a new set of pairing keys. See Pairing with LF MPP Pairing Feature on page 120 and Pairing with Standard Pairing Feature on page 122. • Immediate – (For MCW accessories only.) When the radio There are two options for configuring the radio’s Bluetooth pairing type. The type defines the duration the radio and the accessory retain the pairing information. Re-Pair Timer Infinite (For all Bluetooth devices.) Immediate (For MCW Accessories only.) Re-Pair Timer Options 119 English accessory attempts to re-establish the Bluetooth Connection for a period of time depending upon the Drop Timer value. If the device fails to reconnect within the period, the accessory then powers OFF. • When the radio is powered OFF, the connection, the device will attempt to reestablish Bluetooth Connection within the Drop Timer value. • When the device loses Bluetooth keys are lost immediately, and the user must re-pair the devices. • When the accessory is powered OFF, all key is lost immediately, and accessory attempts to pair again. If pairing is unsuccessful within the Drop Timer value, the accessory automatically powers OFF. • When the radio is powered OFF, pairing Re-Pair Timer Scenarios Advanced Features The radio could not control the Drop Timer of Personal Area Networking (PAN), Dial-Up Networking (DUN), Commercial Off- Infinite (For all Bluetooth devices.) 0 – 15 minutes programmable buffer time to re-establish the Bluetooth Connection when the Bluetooth signal is out of range. If either device powers OFF, the pairing keys are immediately cleared from both devices and the devices must re-pair. Immediate (For MCW Accessories only.) This Timer only applies to the accessory. The programmable timer choices are: 0 – 15 minutes, 2 hours, 4 hours or 8 hours. Do note there are exceptions for Operation Critical Wireless (OCW) headset and PTT which are preprogrammed to 8 hours. This is a "stay alive" time that the accessory will remain ON without the device reconnecting before powering off. The radio will remain ON until the user powers the radio OFF. The radio and accessory will remain paired indefinitely. Once the device re-connect, the timer is reset. Description Re-Pair Timer Options The Bluetooth Drop Timer has two different settings and functions, depending upon the selection of the Re-Pair Timer. Bluetooth Drop Timer English 120 Advanced Features Obstacles that can cause an obstruction in the line-of-sight include trees, buildings, mountains, cars and etc. The range of Bluetooth operation is 10 meters line-of-sight communication. This is an unobstructed path between the location of the signal transmitter (your radio) and the location of the receiver (your device or accessory). Bluetooth Pairing Location Pairing with LF MPP Pairing Feature See Pairing with LF MPP Pairing Feature on page 120 or Pairing with Standard Pairing Feature on page 122 to establish the Bluetooth Connection. Check with your dealer or system administrator for more information about these timers. The-Shelf (COTS) and data services. It is depends on the specifications of these external devices. Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk Time power consumption, not the Standby Time consumption. Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. incremental-pitched tone to indicate paired. OR 2 If the pairing process is successful, you hear an aligning the Bluetooth Pairing Location on the radio to the Bluetooth Pairing Location (a blue dot) on the accessory. 1 Turn on the accessory, then place it close to your radio With your radio’s Bluetooth feature ON, and the Bluetooth tones enabled: Note: Procedure: At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken". To correct this problem, simply position the accessory and radio closer to each other (within the 10 meter defined range) to re-establish clear audio reception. It is NOT recommended that you leave your radio behind and expect your accessory to work with a high degree of reliability when they are separated. 121 English If the connecting process is successful, you hear an incremental-pitched tone. The display shows connected, and the Bluetooth icon turns from b to a. OR If the device already have pairing records and the connecting process fails, you hear a short, low-pitched tone. The display shows connect failed. Repeat step 2 to reconnect the Bluetooth device. OR If the connecting process immediately follows the pairing process and the connecting process fails to complete within 6 seconds, you hear a decremental-pitched tone to indicate unpaired. The display shows unpaired. Repeat step 1 to re-initiate the pairing process. 3 The radio continues to connect to the device. If the pairing process fails, you hear a short, low-pitched tone. The display shows Bluetooth pairing failed. Repeat step 1 again. Advanced Features Note: Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Pairing with Standard Pairing Feature Bluetooth 10 second Re-Connection Timer expires, the display shows momentary connected, and a stops blinking. OR If the Bluetooth device fails to re-connect within 10 seconds, the blinking a is replaced by a persistent b. 2 If the Bluetooth device successfully re-connects before the decremental-pitched tone and the display shows alternating with disconnected. 1 The a starts blinking for up to 10 seconds. You hear a Procedure: The radio shows a when the device has a Bluetooth connection. Below is the scenario and radio indications when the connection is interrupted. Indicating Bluetooth Connection is Lost English 122 Advanced Features The Standard Pairing feature supports pairing Authentication Personal Pairing Number or PIN which ensure your radio recognizes the correct device to pair. The PIN must be exchanged with the radio or the device before the pairing completes. Your radio prompts for the Authentication PIN when needed. Refer to your device’s manual for details about the Bluetooth Authentication PIN of your device if needed. This feature also enables your Bluetooth enabled radio to be visible to another Bluetooth enabled device and receive request to pair from other device. The Bluetooth Standard Pairing feature enables your Bluetooth enabled radio to search for other Bluetooth enabled and discoverable device. Once the device is discovered, you can initiate your radio to send a pairing request to pair with the device. accessory is aligned with the Talk time power consumption, not the Standby time consumption. Ensure the Bluetooth on your device is turned to On and is set to DISCOVERABLE in order to enable your radio to detect your device in Bluetooth. shown. The display shows a list of Bluetooth devices found. 5 When the search timer expires, Available Dev screen is devices found if there are any. OR To stop the searching press the Menu Select button below Stop. 4 The BT Searching screen shows the name of Bluetooth Searching for BT devices. OR You hear the radio sounds a short, low-pitched tone. The Bluetooth feature screen shows BT Search failed. 3 The display changes to BT Searching screen and it shows button directly below On. 2 U or D to Search Devices and press the Menu Select BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Note: Bluetooth Search in Bluetooth Standard Pairing method is used to scan for other Bluetooth devices nearby. It is set to off by default. Searching and Pairing the Bluetooth Device 123 English shown. The display shows a list of Bluetooth devices found. 4 When the search timer expires, Available Dev screen is devices found if there are any. OR Press the preprogrammed button to disable the Bluetooth Search. 3 The BT Searching screen shows the name of Bluetooth Searching for BT devices. OR If the feature fails to initiate, you hear the radio sounds a short, low-pitched tone. The screen shows BT Search failed. 2 The display changes to BT Searching screen and it shows Search feature. 1 Press the preprogrammed button, to enable the Bluetooth OR name and press the Menu Select button directly below Sel to connect to the device.The radio starts pairing to the device. OR Press the Menu Select button below Back to return to Bluetooth feature screen. OR Press H or the Menu Select button below Exit to return to Home screen. 6 If the list shows the required device, U or D to the device Advanced Features Procedure: Turning Bluetooth visibility to on enables other Bluetooth devices to search for your radio. The visibility of the Bluetooth is set to off by default. directly below On. The status changes to Visible to all. Visibility mode is enabled. 2 U or D to Visibility and press the Menu Select button BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Receiving Pairing Request from other Devices Turning Bluetooth Visibility On refuse pairing rquest. 2 Press the Menu Select button below Ok to accept or Cncl to device, the display shows pair request. 1 When your radio receives a pairing request from other Press the preprogrammed to toggle the Bluetooth visibility on or off. This Search function stops when you initiate pairing to a device. momentary Visible to all. Visibility mode is enabled. OR When the timer expires, the display shows momentary Visibility failed. Repeat step 1. 2 You hear a short, medium-pitched tone. The display shows visibility feature. 1 Press the preprogrammed button to enable the Bluetooth OR OR When the timer expires, the status changes to Visibility failed. Repeat step 1. To continue with Bluetooth pairing, please see Pairing with LF MPP Pairing Feature on page 120. Note: name and press the Menu Select button directly below Sel to connect to the device.The radio starts pairing to the device. OR Press the Menu Select button below Back to return to Bluetooth feature screen. OR Press H or the Menu Select button below Exit to return to Home screen. 5 If the list shows the required device, U or D to the device English 124 Advanced Features momentary Visibility Off. Visibility mode is disabled. OR When the timer expires, the status changes to Visibility off failed. Repeat step 1. 2 You hear a short, medium-pitched tone. The display shows visibility. 1 Press the preprogrammed button to disable the Bluetooth OR to the Home screen. 4 Press the Menu Select button directly below Exit to return OR When the timer expires, the status changes to Visibility off failed. Repeat step 2. 3 The display shows Visibility Off. directly below Off. 2 U or D to Visibility and press the Menu Select button BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below The compare PIN authentication method only applicable for Bluetooth version 2.1 and above. If the device or profile does not support this feature, the radio prompts BT profiles not supported as your radio only supports HSP, DUN, PAN and SPP. 125 English OR Press the Menu Select button below Cncl to reject. The display shows Cancel pairing in progress... followed by pair canceled and return to Home screen. OR When the pairing timer expires, the display shows pair Procedure: Note: a Pairing Request Comparing Authentication PIN When Receiving Note: For the security of your radio, Bluetooth Pairing PIN feature is designed to enable your radio to verify the correct device to pair before initiating the pairing. Authentic PIN is used for the verification. Procedure: With the Visibility turns On, Pairing with PIN Authentication Turning Bluetooth Visibility Off Advanced Features 6 The display returns to Home screen. followed by connected. OR When the pairing timer expires, the display shows pair failed. OR When the connecting timer expires, the display shows connect failed. 5 The display shows paired OR If the PIN is correct, the display shows BT profiles not supported. The display returns to Home screen. 4 The display shows Pairing in progress.... XXXXXX. Press the Menu Select button below Ok if the PIN is correct. OR Press the Menu Select button below Cncl to reject if the PIN number is incorrect. The display shows Cancel pairing in progress... followed by pair canceled and return to Home screen. OR When the PIN authentication timer expires, the display shows pair canceled and return to Home screen. 3 Once accepted, the display shows Compare PIN: Friendly Name> pair canceled and return to Home screen. English 126 Advanced Features If the device or profile does not support this feature, the radio prompts BT profiles not supported as your radio only supports HSP, DUN, PAN and SPP. Pairing in progress. OR 3 The radio and device continue pairing. The display shows OR Press the Menu Select button below Cncl to reject. The display shows Cancel pairing in progress... followed by pair canceled and return to Home screen. OR The display shows BT profiles not supported. The display returns to Available Dev screen. 2 Press Ok to proceed. button directly below Sel to initiate pairing. The display shows Pairing in progress... followed by random generated numeric PIN, Compare PIN: XXXXXX. 1 U or D to the required device. Press the Menu Select Follow procedure Searching and Pairing the Bluetooth Device on page 123 to search for Bluetooth devices available, then start pairing with Authentication PIN with the following. Procedure: Note: Numeric PIN Comparing Authentication PIN with Generated button directly below Sel to initiate pairing. 1 U or D to the required device. Press the Menu Select Follow procedure Searching and Pairing the Bluetooth Device on page 123 to search for Bluetooth devices available, then start pairing with Authentication PIN with the following. Procedure: Keying in the Same PIN Comparing Authentication PIN by Manually connected.The display returns to Bluetooth feature screen. OR The display shows connect failed. The display returns to Available Dev screen. 5 The display shows Connecting in progress... followed by Friendly Name> paired. OR If the PIN number is different, the display shows pair failed. The display returns to Available Dev screen. Repeat step 3. 4 If the PIN number is authentic, the display shows pair failed. Repeat step 3. 127 English Friendly Name> paired. OR If the PIN number is different, the display shows pair failed. Repeat step 3. 4 The radio and device continue pairing. The display shows Press the Menu Select button directly below Del to delete. Press Ok to proceed. Enter the same PIN number on the device. OR Press the Menu Select button below Cncl to reject. The display shows Cancel pairing in progress... followed by pair canceled and return to Home screen. OR The display shows BT profiles not supported. The display returns to Available Dev screen. 3 Use the keypad to enter the PIN. Press < to move one space to the left. Press > to move one space to the right. requesting user to enter PIN number . A blinking cursor appears below the Enter PIN:. 2 The display shows Pairing in progress... followed by Advanced Features Headset on. 2 You hear a short, medium-pitched tone. The display shows routing from the radio to the headset. 1 Short press the preprogrammed button to route the audio OR to the Home screen. 3 Press the Menu Select button directly below Exit to return button directly below On. The display shows On. 2 U or D to Bluetooth spkr and press the Menu Select Speaker on. 2 You hear a short, medium-pitched tone. The display shows from the headset to the radio. 1 Press the preprogrammed button to route the audio routing 1 < or > to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. OR to the Home screen. 3 Press the Menu Select button directly below Exit to return button directly below Off. The display shows Off. 2 U or D to Bluetooth spkr and press the Menu Select BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Audio from the Headset to the Radio) Turning Off the Bluetooth Audio (Routing the Procedure: Audio from the Radio to the Headset) Turning On the Bluetooth Audio (Routing the connected.The display returns to Bluetooth feature screen. OR The display shows connect failed. The display returns to Available Dev screen. 6 The display shows Connecting in progress... followed by Friendly Name> PIN auth fail. The display returns to Available Dev screen. Repeat step 3. English 128 Advanced Features BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Information Viewing and Clearing the Bluetooth Device medium-pitched tone. 2 The radio display shows Volume XX, and you hear a short, 1 Adjust volume up/down on the Bluetooth audio device. With the Bluetooth audio device connected to the radio: Procedure: Your radio can only control the volume of MCW and OCW Bluetooth enabled audio device. If the radio is paired with other Bluetooth enabled audio device, its volume is independent from the radio. In this case, the volume is only adjustable on the device. Audio Device Adjusting the Volume of the Radio from Bluetooth 129 English indicate clearing is successful. OR You hear the radio sounds a short, low-pitched tone. The 7 The display shows cleared to proceed. OR Press the Menu Select button directly below No to return to previous screen. 6 Press the Menu Select button directly below Yes to 5 The display shows clear?. button directly below Clr. 4 U or D to the required device, press the Menu Select Bluetooth devices being paired or connected. OR If there are devices being paired or connected, U or D along the to see the status of each device. OR Press the Menu Select button directly below Back to return to the previous screen. 3 The display shows No devices if there are no active Devices the display shows XX connected alternates with XX paired. Press the Menu Select button directly below Sel to see the details. 2 U or D to Devices, once you toggle the highlight to Advanced Features If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.) Select button directly below Yes to proceed. 2 The display shows Clear all BT devices?. Press the Menu directly below Clr to clear all active Bluetooth devices. You hear a short, medium-pitched tone. 1 U or D to Devices and press the Menu Select button Long press the preprogrammed Bluetooth On/Off button. You hear a short, medium-pitched tone. Proceed to step 3. OR In the Bluetooth feature screen, Procedure: Clearing All Bluetooth Devices Information Note: to the previous screen. 8 Press the Menu Select button directly below Back to return display shows clear failed. The display returns to previous screen. English 130 Advanced Features Note: If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.) clearing is successful. OR You hear the radio sounds a short, low-pitched tone. The display shows Clear all BT devices failed. The display returns to Bluetooth feature screen. 4 The display shows All BT devices cleared to indicate progress. 3 The display shows Please wait to indicate clearing is in Your radio must be preprogrammed to allow you to use this feature. new Friendly Name and return to the Bluetooth feature screen. OR Press the Menu Select button directly below Cncl to return to the Bluetooth feature screen. 4 Press the Menu Select button directly below Ok to save the Use the keypad to edit the text. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 3 A blinking cursor appears in the Friendly Name screen. button directly below Edit. 2 U or D to Friendly name and press the Menu Select BT to access the Bluetooth feature screen. 1 < or > to BT. Press the Menu Select button directly below Procedure: Note: Editing the Bluetooth Friendly Name 131 English If the connecting process is successful, you hear an incremental-pitched tone. The display shows LEX 700 connected, and the Bluetooth icon turns from b to a. OR If the device already have pairing records and the connecting process fails, you hear a short, low-pitched tone. The display shows LEX 700 connect failed. Repeat step 2 to reconnect the Bluetooth device. OR 4 The radio continues to connect to LEX 700. incremental-pitched tone from the radio. OR If the pairing process fails, you hear a short, low-pitched tone. The display shows Bluetooth pairing failed. Repeat step 1 again. 3 If the pairing process is successful, you hear an Location on LEX 700 with the Bluetooth Pairing Location on the radio. 2 Place it close to the radio aligning the Bluetooth Pairing 1 Turn on the LEX 700 and activate the Bluetooth feature. With the radio Bluetooth feature ON, and the Bluetooth tones enabled: Procedure: Display only) Pairing with LEX 700 (APX 7000 Dual Advanced Features To unpair the LEX 700, follow the steps in Viewing and Clearing the Bluetooth Device Information on page 129. If the connecting process immediately follows the pairing process and the connecting process fails to complete within 6 seconds, you hear a decremental-pitched tone to indicate unpaired. The display shows LEX 700 unpaired. Repeat step 1 to re-initiate the pairing process. English 132 Advanced Features Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Once a configuration upgrade is downloaded to your radio, you can install new changes immediately or delay changes to be installed on the radio when it is being powered up. Your radio can also be configured to allow you to accept or reject an upgrade. This feature enables configuration data to be upgraded to your radio over-the-air. This feature retains full use of the radio during the configuration data transfer without interrupting communication. The upgrade pauses to give priorities to voice call, and continues after the voice call ended. Programming Over Project 25 (POP 25) (ASTRO 25 and ASTRO Conventional) If your radio has problem of upgrade over-the-air, consult the qualified technician for details. done. OR If the upgrade failed, the display shows Program failed. The radio remains in current configuration. 3 If the upgrade is successful, the display shows Program request to upgrade immediately. The display shows Upg Rx In Prog to indicate the upgrade received is in progress. OR Press the Menu Select button below Dlay to delay the request to upgrade. The radio prompts to upgrade in the next power up of your radio. OR Press the Menu Select button below Rej to reject the request to upgrade. The display shows Upg Aborted. The radio continues to function with the current configuration until it gets reprogrammed. 2 Press the Menu Select button below Acpt to accept the 1 The display shows Upgrade?. Procedure: Responding to the notification of Upgrade Check with your agent if Voice Announcement is available for the feature you need. This feature must be preprogrammed by a qualified radio technician. when the radio is receiving calls. 133 English • Low – disables the voice of the feature from announcing when the radio is receiving calls. • High – enables the voice of the feature to announce even The two options of priority for the Voice Announcement available are: Note: Each voice announcement is within a limit of three seconds maximum. The sum duration of all different voice announcements in a radio shall be no more than 1000 seconds. This feature enables the radio to audibly indicate the current feature mode, zone or channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Voice Announcement Advanced Features All the three programmable buttons at the side of the radio support this feature. Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority. button or switch of the radio to launch or terminate Scan, PL Disabled, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation. • Press either the Menu Select button or preprogrammed The radio announces the current channel. • Change to a new channel remaining within the current zone. zone and channel it is transmitting. • Change to a new zone. The radio announces the current Note: (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting. • Press the preprogrammed voice announcement button and channel it is transmitting. • The radio powers up. The radio announces the current zone You hear a voice announcement when the features below are preprogrammed in the radio. Procedure: English 134 Advanced Features When mixing SSA with received voice audio, the SSA alert is reduced in volume to ensure that the voice message is still heard clearly. Therefore, it is important that the SSA audio files are created with clear loud audio to ensure they can still be heard clearly when played at reduced levels. Alert alias, alert tone, and alert period can be preprogrammed. Alert period is the duration for the radio to repeat the alert tone. An interval of 5 seconds might impact the battery life of the radio. Check with your dealer or system administrator for more details. 1 > or < to SSA. Procedure: Sending SSA Notification to Single Site Note: Upon the activation of a SSA, the receiving radios display the alert alias and generate the periodic alert tone. A Site Selectable Alert (SSA) is an Intelligent Lighting indicator with audio alert sent to radios at a site or a few sites to notify the users when there is a special situation that they need to be aware of. Only authorized radios are enabled to send SSA. Using Site Selectable Alerts (ASTRO 25) to the Home screen. 7 Press the Menu Select button directly below Exit to return successful. OR If the site is not available, the display shows not available. OR If the site does not exist, the display shows does not exist. 6 If the request is successful, the display shows Req Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 5 D or U to select the desired Alert Alias and press the button directly below Sel. The display shows the Select Alert screen. 4 D or U to the desired Site Alias. Press the Menu Select directly below Sel. The display shows the Select Site screen. 3 D or U to Start Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 135 English Alert screen. OR If a wrong Site ID is entered, the display shows Invalid ID and prompts to enter the Site ID again. 6 If a correct Site ID is entered, the display shows the Select directly below Ok. 5 Key in the desired Site ID and press the Menu Select button Press the Menu Select button directly below Edit. The display shows the Enter SiteID screen. 4 D or U to {SiteID Entry} to send alert via manual entry. directly below Sel. The display shows the Select Site screen. 3 D or U to Start Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. Procedure: Manual Entry Sending SSA Notification to Single Site Via If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the with the intelligent lighting at Home screen. Advanced Features If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the with the intelligent lighting at Home screen. to the Home screen. 9 Press the Menu Select button directly below Exit to return successful. OR If the single site is not available, the display shows not available. OR If the single site does not exist, the display shows does not exist. 8 If the request is successful, the display shows Req Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 7 D or U to select the desired Alert Alias and press the English 136 Advanced Features successful. OR If one or more sites are not available, the display shows Not all sites available. Repeat Step 3. 6 If the request is successful, the display shows Req Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 5 D or U to select the desired Alert Alias and press the directly below Sel. The display shows the Select Alert screen. 4 D or U to {All Sites} and press the Menu Select button directly below Sel. The display shows the Select Site screen. 3 D or U to Start Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. Procedure: Sending SSA Notification to All Sites Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 5 D or U to select the desired Alert Alias and press the directly below Sel. The display shows the Select Alert screen. 4 D or U to {All Avail} and press the Menu Select button directly below Sel. The display shows the Select Site screen. 3 D or U to Start Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. Procedure: Sending SSA Notification to All Available Sites If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the with the intelligent lighting at Home screen. to the Home screen. 7 Press the Menu Select button directly below Exit to return 137 English Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 4 D or U to select the desired Site Alias and press the Menu directly below Sel. The display shows the Select Site screen. 3 D or U to Stop Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. Procedure: Stopping SSA Notification of a Single Site If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the with the intelligent lighting at Home screen. to the Home screen. 7 Press the Menu Select button directly below Exit to return successful. 6 If the request is successful, the display shows Req Advanced Features button directly below Edit. 4 D or U to {SiteID Entry} and press the Menu Select directly below Sel. The display shows the Select Site screen. 3 D or U to Stop Alert and press the Menu Select button display shows the Site Alert screen. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. Procedure: Via Manual Entry Stopping SSA Notification of a Single Site 7 The SSA Alert for the designated site stops. to the Home screen. 6 Press the Menu Select button directly below Exit to return successful. OR If the site is not available, the display shows not available. OR If the site does not exist, the display shows does not exist. 5 If the request is successful, the display shows Req English 138 Advanced Features 9 The SSA Alert for the designated site stops. to the Home screen. 8 Press the Menu Select button directly below Exit to return successful. OR If the single site is not available, the display shows not available. OR If the single site does not exist, the display shows does not exist. 7 If the request is successful, the display shows Req and prompts to enter the Site ID again. OR If a correct Site ID is entered, the display shows Sending req. 6 If a wrong Site ID is entered, the display shows Invalid ID required Site ID and press the Menu Select button directly below Send. 5 The display shows the Enter SiteID screen. Key in the 1 > or < to SSA. 2 Press the Menu Select button directly below SSA. The 1 > or < to SSA. 2 Press the Menu Select button directly below SSA. The 4 D or U to {All Avail} and press the Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 4 D or U to {All Sites} and press the Menu Select button directly below Send. The display shows Sending req. OR If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. 7 The SSA Alert for all sites stop. to the Home screen. 6 Press the Menu Select button directly below Exit to return successful. OR If one or more sites are not available, the display shows Not all sites available. Repeat Step 3. 7 The SSA Alert for all available sites stop. to the Home screen. 139 English 6 Press the Menu Select button directly below Exit to return successful. 5 If the request is successful, the display shows Req directly below Sel. The display shows the Select Site screen. directly below Sel. The display shows the Select Site screen. 5 If the request is successful, the display shows Req 3 D or U to Stop Alert and press the Menu Select button 3 D or U to Stop Alert and press the Menu Select button display shows the Site Alert screen. Procedure: Procedure: display shows the Site Alert screen. Stopping SSA Notification of All Available Sites Stopping SSA Notification of All Sites Advanced Features If the radio transmission personalities contain one 700MHz channel, the entire personality will not be able to use LTE. ATTENTION! This module allows the voice communication of P25 and data communication via LTE to take place simultaneously. Networks supported include the public safety broadband network (band 14) and Verizon’s commercial network (band 13). The APX7000L enhances the current radio operation by providing the radio with faster information delivery over an LTE broadband network. Utilizing the LTE network additionally allows the radio to perform simultaneously LMR voice operation while sending and receiving data via the LTE network. LTE eliminates the need for radios to be physically present at a service facility when reconfiguration is required. Long Term Evolution (LTE) (APX 7000L Only) English 140 Advanced Features Speaker grill of APX 7000L Microphone The APX 7000L radio exterior has the speaker grill bumped out. Besides this, the remainder of the exterior is identical to APX 7000. LTE is operational again when the frequencies are switched back to either a VHF or a 800 MHz LMR frequency. When the radio is switched to operate in 700MHz LMR, LTE operation is turned off. The radio still can operate on 700MHz LMR where the LMR voice and data are available to the user. The LTE feature can be preprogrammed to a programmable button for quick access to LTE screen or to activate LTE feature. The LTE button must be preprogrammed by a qualified technician before user can use it. LMR Currently LTE and IV&D are mutually exclusive. Both systems cannot operate at the same time. IV&D The radio is preprogramed to stop LTE operation when radio switched to a LMR 700MHz frequency. Operation Scenarios System The table below describes the condition when the radio works in different operating systems with LTE. Conventional and Broadband 141 English Use LTE data transmission network when available. When LTE is not available or turned off, the radio falls back to using Conventional LMR data, if available. Once LTE coverage becomes available again, the radio reverts back to using LTE data transmission network. Trunking and Broadband Use only LTE data transmission network. In the absence of LTE coverage, the radio has no data functionality. Operation Scenarios Use LTE data transmission network when available. When LTE is not available or turned off, the radio falls back to using IV&D LMR data, if available. Once LTE coverage becomes available again, the radio reverts back to using LTE data transmission network. Broadband Only Profiles There are three different profiles available for LTE data operation. Data Profiles Available for LTE Advanced Features connected. The Status shows Connected. The LTE icon appears at the top of the front display to indicate LTE modem is connected. OR The display shows LTE service error if there is an encryption error. The Status shows Service error. OR The display shows No LTE service if there are no LTE 5 The display shows LTE connected once the radio is initating connection to LTE system. 4 The Status shows Connecting... to indicate the radio is to indicate radio is initating the LTE connection. OR Press the Menu Select button directly below On to enable LTE connection. 3 Press and hold the LTE button. The screen prompts LTE on prompts Please wait. Once LTE modem is ready, the display shows the LTE screen. 2 If LTE modem is not ready or busy setting up, the screen OR < or > to LTE. Press the Menu Select button directly below LTE to enter the LTE screen. 1 Press the LTE button to enter the LTE screen. Procedure: Turning On the LTE at the LTE Menu Screen English 142 Advanced Features connected. The Status shows Connected. The LTE icon appears at the top of the front display to indicate LTE modem is connected. OR The display shows LTE service error if there is an encryption error. OR The display shows No LTE service if there are no LTE networks available. 2 The display shows LTE connected once the radio is shows LTE on to indicate radio is initating the LTE connection. 1 Press and hold the preprogrammed LTE button. The screen Procedure: Turning On the LTE with LTE Button It is advisable to turn off the LTE if the radio prompts SLTE service error or No LTE service. For the error no LTE service available, turn on the LTE after you moved to another site to check the availablity. screen. 6 Press the Menu Select button below Exit to return to Home networks available. The Status shows No service until successfully connected to LTE or encounter service error. screen. 5 Press the Menu Select button below Exit to return to Home indicate the LTE is off. 4 The Status shows Off and the LTE icon dissapears to to indicate the LTE connection is off. OR Press the Menu Select button directly below Off to disable LTE connection. 3 Press and hold the LTE button. The screen shows LTE Off the LTE screen. 2 Press the Menu Select button directly below LTE to access to Step 3. OR < or > to LTE. 1 Press and hold the preprogrammed LTE button and proceed Procedure: If the radio is out of LTE coverage and you know you will be out of LTE coverage for a long period of time, would be good to disable LTE feature to extend the radio battery life. Turning Off the LTE Connection It is advisable to turn off the LTE if the radio shows Service error or no LTE service. For error no LTE service available, turn on the LTE after you moved to another site to check the availablity. Status Item 143 English Connecting – The radio is trying to connect to an LTE modem Connected – LTE communication is currently on. Disconnected – LTE communication is currently disconnected. Disabled – LTE communication is currently disabled on the selected channel. Off – LTE communication of the radio is currently off. No Service – No LTE service detected at the current site. Service Error* – There is an LTE service error. LTE HW error* – There is an LTE hardware error. VPN auth error *– Incorrect key installed for VPN. Service fatal error** – LTE function has come to a stall. Status and Description Here is the description of different items which are shown on the LTE screen. Information at the LTE Screen Advanced Features Network Item Please wait - The radio is trying to connect to an LTE modem. Unavailable - The radio does not have an LTE connection currently. Rating of the signal strength - You will see one of the following rating when LTE is connected: Excellent > Good > Fair > Poor - The currently connected LTE network name. Unavailable - No LTE network connected currently. Status and Description * Bring the radio to the qualified technician to check the issue if the error persists. ** You can try to power on your radio again to reinitiate the LTE function. If this error persists, bring your radio to the qualified technician to verify the issue. Signal Strength English 144 Advanced Features If the display is showing LTE screen when entering the unprogrammed channel, the display returns to Home screen immediately and you are unable to see nor access the LTE screen. When entering a unprogrammed channel the display prompts Unprogrammed and the LTE menu dissapears. Pressing the LTE button prompts short, low-pitched tone. Unprogrammed Channel Changing from LTE-enabled Channel to If the display is showing LTE screen when entering the LTEdisabled channel, the display returns to Home screen immediately. When entering a non-LTE capable channel the status field in the LTE screen shows Disabled. Press or press and hold of the LTE button prompts short, low-pitched tone. LTE-disabled Channel Changing from LTE-enabled Channel to With the LTE of the radio turned on, when the radio moves back to LTE connected site, the rado prompts LTE connected. When the radio moves beyond the LTE network coverage, which means out-of-range, the radio prompts No LTE service. The LTE screen is accessible. Refer to Information at the LTE Screen on page 143 for the status shown at the LTE screen. Entering or Exiting Out-of-Range Site The radio can also be preprogrammed to log only the radio IDs associated with incoming Dispatch Calls. Check with your dealer or system administrator for more information. 1 < or > to Rcnt. 145 English Procedure: Press the preprogrammed Recent Calls button and proceed to Step 3. OR Follow the procedure below. Note: • Emergency Call (Incoming Only) • Phone Call (Outgoing Only) • Private Call • Selective Call • Call Alert This feature allows you to view the recent incoming and outgoing call information of the following call types: Viewing the Recent Calls Utilities Advanced Features Procedure: Press and hold the preprogrammed Light/Flip button to flip the display. This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still in the carry holder attached to your belt. Using the Flip Display The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. the Home screen. OR Press H or the PTT button to return to the Home screen. 4 Press the Menu Select button directly below Exit to return to See Basic Zone Bank 1 and Basic Zone Bank 2 on page 22 for more information on the status icons. the zone name based on the bank and switch position selected. 2 The top display shows the status icons (A, B, C, D, E or F) or the position between Bank 1 and Bank 2. 1 Use the preprogrammed Basic Zone Bank button to toggle Procedure: The Basic Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Basic Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature. This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions. 3 U or D to scroll through the list. Note: Selecting a Basic Zone Bank the Recent Calls feature screen. 2 Press the Menu Select button directly below Rcnt to access English 146 Advanced Features The Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Enhanced Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature. or third zone in the selected EZB. 2 Turn the 3-Position A/B/C Switch to select the first, second scroll the EZB up or down. OR Press and hold the preprogrammed EZB Up or EZB Down button to fast scroll the EZB up or down. 1 Press the preprogrammed EZB Up or EZB Down button to Procedure: Note: Please refer to your agent or qualified radio technician to enable this feature. 2 Press the Menu Select button directly below Pwr. 1 < or > to Pwr. 147 English Procedure: Use the preprogrammed Transmit Power Level Switch to toggle the power level between low and high power. OR Follow the procedure below. • Select High for a longer transmitting distance. conserve power. • Select Low for a shorter transmitting distance and to Settings: These reduced transmit power level settings do not affect your radio’s receiving performance, nor diminish the overall quality of the radio’s audio and data functionality given the following conditions. Note: This feature enables you to reduce the transmit power level for specific case that require a lower power level. You can select the power level at which your radio transmits. The radio always turns on to the default setting. This feature is created in order to allow users to communicate in more zones. An Enhanced Zone Bank (EZB) consists of three zones. This also means each icon A, B, C, ... or Y consist of three zones. You can use the preprogrammed 3-position A-B-C switch to select the first, second or third zone in an EZB. This feature allows user to navigate from up to 75 zones in 25 EZBs. Selecting the Power Level Selecting an Enhanced Zone Bank Advanced Features The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. the required radio profile. 4 Press the Menu Select button directly below Sel to select 3 U or D to scroll through the menu selections. the Profiles feature screen. 2 Press the Menu Select button directly below Prfl to access 1 < or > to Prfl. Procedure: Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. Note: Please refer to a qualified technician for more information. This feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile. Selecting a Radio Profile OR The display shows High power and the high power icon. 3 The display shows Low power and the low power icon. English 148 Advanced Features alias disappears from the Home screen. OR The display shows momentary Radio ID on, and the radio alias appears on the Home screen. 2 The display shows momentary Radio ID off, and the radio 1 Press the Menu Select button directly below MyID. Procedure: This feature allows you to display or hide the radio alias (name). Enabling and Disabling the Radio Alias the Home screen indicates the current selected radio profile. 5 The radio returns to the Home screen. The profile name on OR Press the Menu Select button directly below Exit to exit the screen without making any changes. Your radio must be preprogrammed to allow you to use this feature. If an external speaker or microphone accessory is attached to the radio, neither internal speaker is operational as audio is routed to the accessory. the Profiles feature screen. 2 Press the Menu Select button directly below Prfl to access 1 < or > to Prfl. Procedure: Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. Note: The secondary speaker also has a "whisper" mode with a modified volume taper for quieter modes of operation. While both speakers function together with the secondary speaker enhancing intelligibility of the received audio during typical radio operation, each speaker has an independently-tuned frequency response and volume level operation. Note: This feature allows you to select the speaker route for the radio's audio from either the main or the secondary speaker using the radio profile settings. Selecting the Audio Speaker The backlight setting also affects the Menu Select buttons, the Menu Navigation buttons and the keypad backlighting accordingly. 149 English Procedure: Press the preprogrammed Light/Flip button to toggle the backlight on or off. OR Press any key of the keypad, the Menu Select or Menu Navigation buttons, or any programmable radio controls or buttons to turn the backlight on. Note: Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radio's front display. You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display or keypad difficult to read. Controlling the Display Backlight the Home screen indicates the current selected radio profile. 5 The radio returns to the Home screen. The profile name on the radio profile with the required speaker routing. OR Press the Menu Select button directly below Exit to exit the screen without making any changes. 4 Press the Menu Select button directly below Sel to select 3 U or D to scroll through the menu selections. Advanced Features Note: English 150 Advanced Features The preprogrammed Light/Flip button of the accessories connected to the radio such as Display Remote Speaker Microphone (DRSM) is disabled when the radio is in Night Vision Goggles (NVG) display mode. The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level. Intelligent lighting indicators, TX LED and RX LED are all disabled on both the radio and the connected accessory when the radio is in NVG display mode. Accessory connected to the radio that is in NVG display mode such as Display Remote Speaker Microphone (DRSM) has its backlight always in OFF state. Caution REMOVE your NVG if you operate the radio in non-NVG compatible display mode. Wearing the NVG to operate in non-NVG compatible display mode might injure your EYES. During tactical nighttime operations of military entities worldwide, the Night Vision Goggles (NVG) is used to see in the dark. Your radio is 3rd generation NVG compatible. When the radio is in NVG display mode, the radio's front display and top display emit a very low illumination backlight to allow the user to operate the radio with the goggles on. Indicators to Suite Night Vision Goggles Setting Up the Radio Display and Visual mode. The profile name on the Home screen indicates the current selected radio profile. 5 The radio returns to the Home screen with NVG display the required radio profile. OR Press the Menu Select button directly below Exit to exit the screen without making any changes. 4 Press the Menu Select button directly below Sel to select 3 U or D to the designated NVG profile. the Profiles screen. 2 Press the Menu Select button directly below Prfl to access 1 < or > to Prfl. Follow the procedure below. OR Use the preprogrammed Profile button and proceed to Step 3. Procedure: Get familiar with your radio NVG feature and operation before you use it with your Night Vision Goggles. 3 Toggle again to unlock the keypad. 2 The display shows Kypd/Ctrl Lock. to on. 151 English 1 Toggle the preprogrammed Keypad Lock button or switch Procedure: You can lock your radio’s keypad, programmable buttons, rotary knobs and switches to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suite your usage. Locking and Unlocking the Keypad and Controls Advanced Features Turning Voice Mute On or Off You can enable and disable voice transmission, if needed. Procedure: Press the preprogrammed Voice Mute button to turn the feature off or on. OR Follow the procedure below. 1 < or > to VMut. 2 Press the Menu Select button directly below VMut. 3 The display shows momentary Voice mute off, and you hear a short tone, indicating that the feature is disabled. OR The display shows momentary Voice mute on, and you hear a short tone, indicating that the feature is enabled. Turning Keypad Tones On or Off You can enable and disable keypad tones, if needed. Procedure: Press the preprogrammed Keypad Mute button to turn the tones off or on. OR Follow the procedure below. 1 < or > to Mute. 2 Press the Menu Select button directly below Mute. 3 The display shows momentary Tones off, indicating that the keypad tones are disabled. OR The display shows momentary Tones on, and you hear a short tone indicating that the keypad tones are enabled. English 152 Advanced Features You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. restarts and the LED lights up solid red. 3 Press the PTT button to re-transmit. The time-out timer 2 Release the PTT button. The timer resets. time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the PTT button. 1 Hold down the PTT button longer than the preprogrammed Procedure: Note: The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. Check with your dealer or system administrator for additional programmable settings for this feature. U or D to change the selected item. change. 153 English < or > one or more times to move to an item you wish to OR 4 U or D to change the selected item. item blinks. 3 Press the Menu Select button directly below Edit. The first display shows the current setting of the radio. 2 Press the Menu Select button directly below Clck. The 1 < or > to Clck. Procedure: Editing the Time and Date Note: • The default setting for the domestic date shows MDY. setting. • The AM/PM selection is not available for the 24-hour clock 12:00AM. • The default time setting is a 12-hour clock.The display shows Settings: You can set the time and date for your radio. This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. Setting the Time and Date Using the Time-Out Timer Advanced Features Note: If a call arrives while the radio is in the clock-setting menu, the radio exits clock setting and displays the call information. Any changes made before the call is NOT saved. Press H at any time to return to the Home screen without saving your changes. have finished to save your changes and return to the Home screen. OR Press the Menu Select button directly below Cncl to discard all changes and return to the Home screen. 5 Press the Menu Select button directly below Ok once you OR Press the Menu Select button directly below Exit to exit the screen without making any changes and return to the Home screen. English 154 Advanced Features You hear all traffic on a channel. The radio responds only to your messages. Carrier squelch (C) PL or DPL Normal Squelch Digital Carrier-Operated Squelch (COS) Option You hear any digital traffic having the correct network access code. You hear any digital traffic. Result One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information. Digital Options Result Mode Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Analog Options This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Features Using the Conventional Squelch Operation You hear any digital traffic having the correct network access code and correct talkgroup. Selective Switch Note: When this feature is active, the Carrier Squelch status indicator is displayed. Procedure: Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio will also unmute to any digital activity on a digital channel. Using the PL Defeat Feature Result Option 155 English If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. When smart PTT is enabled in your radio, you cannot transmit on an active channel. Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. (Conventional Only) Using the Smart PTT Feature Your radio’s ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message. This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. Using the Digital PTT ID Feature Advanced Features Transmit Inhibit on Busy Channel with Wrong Squelch Code Quick-Key Override You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. You cannot transmit if any traffic is detected on the channel. Description Transmit Inhibit on Busy Channel with Carrier Mode Three variations of smart PTT are available: English 156 Advanced Features the Home screen. 3 Press the Menu Select button directly below Exit to return to display shows the details of the battery. 2 Press the Menu Select button directly below Batt. The Use the Options Menu. 1 < or > to Batt. Procedure: Accessing the Battery Info screen has gone through. • Estimated Charges – Number of charges cycles the battery mAh. • Remaining Capacity – Remaining power of the battery in • Rated Capacity – Percentage of current battery capacity. The information shown are: This feature displays the current capacity and charges cycles of your battery when an IMPRES Battery is powering your radio. This feature must be enabled in your radio to see the information. IMPRES™ Battery Annunciator Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit. • Soft ID (If Enabled) • Control Assignments • IP Display (only when the language of the display is set to non-English) • Language Pack ID and Version (optional) • Option Board Software Version Option Board Serial Number (optional) Processor Version RF Band Flash Size & Type Serial Number KG (Secure Algorithm) Note: 157 English Press H at any time to return to the Home screen. • IMEI (APX 7000L only) • IMSI (APX 7000L only) • ICCID (APX 7000L only) (optional) • Expansion Board Type Address (optional) • Option Board Bluetooth Option Board Type (optional) Tuning Version Flash Code ESN Model Number Secure Version DSP Version • • • • • • • • Radio Information • • • • • • • This feature displays the following information of your radio: Your radio contains information on the following: Host Version Accessing the Radio Information Accessing the General Radio Information Advanced Features • iosu • LOOPBACK • iosc • Ite1 APX 7000L radio has different list of information as shown in the following. This feature displays the device name, IP address, and status of your radio. Viewing the IP Information OR Press the Menu Select button directly below Back to return to the previous screen. OR Press H to return to the Home screen. 5 U or D to scroll through the various information. 4 The display shows the Information screen. directly below Sel. 3 U or D to Radio Info and press the Menu Select button 2 Press the Menu Select button directly below Info. 1 < or > to Info. Procedure: Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. English 158 Advanced Features The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information. • device name OR Press the Menu Select button directly below Back to return to the previous screen. OR Press H to return to the Home screen. 5 U or D to scroll through the various information. 4 The display shows the IP Info screen. below Sel. 3 U or D to IP Info and press the Menu Select button directly 2 Press the Menu Select button directly below Info. 1 < or > to Info. Procedure: Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. Note: • vpn1 OR Press the Menu Select button directly below Back to return to the previous screen. OR Press H to return to the Home screen. 5 U or D to scroll through the various information. 4 The display shows the Control Map screen. directly below Sel. 3 U or D to Control map and press the Menu Select button 2 Press the Menu Select button directly below Info. 1 < or > to Info. Procedure: Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. See Programmable Features on page 11 for more information on the various programmable features of your radio. Use the keypad to edit the text. Press < to move one space to the left. Press > to move one space to the right. 6 A blinking cursor appears in the Edit Soft ID screen. 159 English current Soft ID. OR Press the Menu Select button directly below Back to return to the previous screen. 5 Press the Menu Select button directly below Edit to edit the 4 The display shows the current Soft ID. below Sel. 3 U or D to Soft ID and press the Menu Select button directly 2 Press the Menu Select button directly below Info. 1 < or > to Info. Procedure: Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. Your radio must be preprogrammed to allow you to use this feature. This feature allows you to change your username. This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. Note: Editing the Soft ID Viewing the Control Assignments Advanced Features new Soft ID and return to the previous screen. OR Press the Menu Select button directly below Cncl to return to the previous screen. 7 Press the Menu Select button directly below Ok to save the Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. English 160 Advanced Features Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . . . page 161 Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 162 Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 163 Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . . page 163 Taking Care of the Battery . . . . . . . . . . . . . . . . . . . . . page 164 Checking the Battery Charge Status . . . . . . . . . . . page 164 Battery Recycling and Disposal . . . . . . . . . . . . . . . page 165 Take a moment to review the following: Helpful Tips Caution Vent Port 161 English Your radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours. Exceeding either maximum limit may result in damage to the radio. • (For APX 7000/APX7000L R Radios Only) a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers. This could create leak paths into the radio and the radio’s submergibility will be lost. • Your radio casting has Caring for Your Radio Helpful Tips ! Caution English 162 Helpful Tips damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. • Do not disassemble the radio. This could the radio well so that any water that may be trapped inside the speaker grille and microphone port can be removed. Otherwise, the water will decrease the audio quality of the radio. • If the radio has been submerged in water, shake submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio. • If the radio battery contact area has been Elastomer technology materials used for seals in rugged portable radios can age with time and environmental exposure. Therefore, Motorola recommends that rugged radios be checked annually as a preventive measure in order to assure the watertight integrity of the radio. Motorola details the disassembly, test, and reassembly procedures along with necessary test equipment needed to inspect, maintain and troubleshoot radio seals in the radio’s service manual. • (For APX 7000/APX 7000L R Radios Only) Caution grease. Do not submerge the radio in the detergent solution. Do not use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures. 3 Clean battery contacts with a lint-free cloth to remove dirt or bristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth. 2 Apply the solution sparingly with a stiff, non-metallic, short- one gallon of water (0.5% solution). 1 Combine one teaspoon of mild dishwashing detergent to To clean the external surfaces of your radio: Procedure: Cleaning Your Radio radio must be turned off. Otherwise, the Man Down Alert and Emergency may be accidentally triggered. • When charging the radio using a wall mounted charger, the use the connector. Replace the cover immediately once the accessory has been disconnected. • Keep the accessory-connector cover in place until ready to • Do not disassemble the radio. chemicals. • Avoid subjecting the radio to corrosives, solvents or submerge the radio unless it is a ruggedized, APX 7000/ APX 7000L R model. • Avoid subjecting the radio to an excess of liquids. Do not 163 English Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for an additional period of either one or two years beyond the normal expiration date of the standard warranty. For more information about ESP, contact the Motorola Radio Support Center at 3761 South Central Avenue, Rockford, IL 61102 (800) 227-6772 / (847)725-4200. Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. • Do not pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna. Servicing Your Radio Handling Your Radio Helpful Tips • you hear a low-battery “chirp” (short, high-pitched tone). • the LED blinks red when the PTT button is pressed. When your battery is low: LED and Sounds You can also check the battery charge status via the menu entry. See IMPRES™ Battery Annunciator on page 156 for more information. • the fuel gauge icon on the display. • the LED and sounds. Your radio can indicate the battery’s charge status through: Checking the Battery Charge Status Taking Care of the Battery English 164 Helpful Tips Top Display Top Display Top Display Gauge 26% to 50%* 51% to 75%* 76% to 100% full* Battery Charge A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one. Fuel Gauge Icon 11% to 25%* 10% or less (at 10%, the gauge begins blinking) Top Display Top Display *These are for IMPRES battery operation only. Battery Charge (Continued) Gauge 165 English For the of the drop-off facility closest to you, access RBRC's Internet web site at www.rbrc.com or call 1-800-8-BATTERY. This internet site and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies. In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers participate in this program. Battery Recycling and Disposal Helpful Tips http://www.motorolasolutions.com/APX The accessory link below is for APX radios. Not all accessories are FCC certified to operate with all APX models and/or bandsplits. Please refer to the specific APX radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility. Accessories English 166 Accessories or 700/800 application where the Public Safety Microphone (PSM) is used with the corresponding PSM antenna. This antenna is only for GPS reception and cannot be used for receive/transmit operation at UHF, VHF or 700/800. This antenna is never to be used on the PSM. 1 GPS only antenna is only used in either a single band UHF Highlights for the Accessories Repeat “MAYDAY” and the name of the vessel. “WE ARE LOCATED AT _______________________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. “THIS IS _____________________, CALL SIGN __________.” If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order: 1 “MAYDAY, MAYDAY, MAYDAY.” Emergency Channel Special Channel Assignments Take a moment to review the following: Special Channel Assignments . . . . . . . . . . . . . . . . . . page 167 Operating Frequency Requirements . . . . . . . . . . . . . page 168 Declaration of Compliance for the User of Distress and Safety Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 170 Appendix: Maritime Radio Use in the VHF Frequency Range Specify what kind of assistance you need. State the number of persons on board and the number needing medical attention, if any. Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. “OVER.” 167 English For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Non-Commercial Call Channel 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. 10 Wait for a response. • latitude and longitude • bearing (state whether you are using true or magnetic north) • distance to a well-known landmark • vessel course, speed or destination State the nature of the distress. State the position of the vessel in distress, using any information that will help responders to locate you, e.g.: Appendix: Maritime Radio Use in the VHF Frequency Range Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Note: Transmit 156.050 156.100 Channel Number 160.700 160.650 Receive Frequency (MHz) Table A-1: VHF Marine Channel List Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. • in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. on ships subject to the Safety Convention, the radio must be capable of operating: • • A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows: • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency Operating Frequency Requirements English 168 Appendix: Maritime Radio Use in the VHF Frequency Range 157.000 157.100 22 156.950 19 157.050 156.900 18 156.850 17** 20 156.750 156.800 156.700 14 16 156.650 15** 156.600 156.600 12 13** 161.700 161.650 161.600 161.550 161.500 156.850 156.800 156.750 156.700 156.650 156.550 156.500 156.500 156.450 156.550 156.450 – 160.950 11 156.400 – 160.850 160.800 160.750 Receive 10 156.350 156.250 156.200 156.300 156.150 Transmit Channel Number Frequency (MHz) Table A-1: VHF Marine Channel List (Continued) 160.625 160.675 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 24 25 26 27 28 60 62 160.875 160.925 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725 65 66 67** 68 69 71 72 73 74 160.775 156.725 156.675 – 156.575 156.475 156.425 156.375 160.825 156.175 156.225 63 160.725 162.000 161.950 161.900 161.850 161.800 161.750 Receive Transmit Channel Number Frequency (MHz) Table A-1: VHF Marine Channel List (Continued) 157.425 157.375 157.325 157.275 157.225 157.175 157.125 157.075 157.025 156.975 156.925 156.875 *** *** Transmit 162.025 161.975 161.925 161.875 161.825 161.775 161.725 161.675 161.625 161.575 161.525 – *** *** Receive Frequency (MHz) Note: A – in the Receive column indicates that the channel is transmit only. 169 English Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. ** Low power (1 W) only *** Guard band 88 87 86 85 84 80 79 78 77** 76 75 Channel Number Table A-1: VHF Marine Channel List (Continued) Appendix: Maritime Radio Use in the VHF Frequency Range Impedance Max Data Rate Input Voltage (Volts Peak-topeak) 3.6 V USB 9.6 kb/s 5V SB9600 5k Ohm 90 Ohm 120 Ohm 28 kb/s 12 Mb/s 18 V RS232 Table A-2: Technical Paratmeters for Interfacing External Data sources The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies spedified in RSS-182 Section 6.1. Declaration of Compliance for the User of Distress and Safety Frequencies English 170 Appendix: Maritime Radio Use in the VHF Frequency Range Acknowledgment of communication. A channel that has traffic on it. An RF signal that has a continuous nature rather than a pulsed or discrete nature. Automatic Registration Service Motorola standard for wireless digital trunked communications. Motorola standard for wireless digital conventional communications. A feature that allows the radio to automatically scan the members of a scan list. Bluetooth is an open wireless technology standard for exchanging data over short distances from fixed and mobile devices with high levels of security. Active Channel Analog Signal ARS ASTRO 25 ASTRO Conventional Autoscan Bluetooth Definition ACK Term This glossary is a list of specialized terms used in this manual. Glossary A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding. Central Controller Channel 171 English In a trunking system, one of the channels that is used to provide a continuous, twoControl Channel way/data communications path between the central controller and all radios on the system. A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. Carrier Squelch Privately page an individual by sending an audible tone. Call Alert Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”. Bluetooth pairing occurs when two bluetooth devices exchanged a passkey to form a paired Bluetooth wireless connection. Definition Bluetooth Pairing Term Glossary Digital Private Line (DPL) Digital Signal Processing A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. Deadlock DSP Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. An individual who has radio system management duties. A visual tracking marker (a blinking line) that indicates a on the display. Cursor Dispatcher Codeplug CP Digital Signal Commercial Off-The-Shelf COTS An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. A scan list that includes only conventional channels. Conventional Scan List Definition Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). Term Conventional English 172 Glossary Integrate Circuit Card Identity International Mobile Equipment Identifier International Mobile Subscriber Identity Inter-OS User for user IP traffic ICCID IMEI IMSI Iosu The first display information after the radio completes its self test. Disconnect. Hang Up Home screen Frequency Modulation FCC FM Federal Communications Commission. Failsoft Electrical Serial Number A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. ESN Encrypted Integrated Data Dynamic System Resilience DSR EID A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. Definition Dynamic Regrouping Term Inter-OS Control for control IP traffic Adapter name used by the radio for LTE traffic Integrated Voice and Data Key-variable loader: A device for loading encryption keys into the radio. Liquid crystal display. Light-emitting diode. Lithium ion. Long Term Evolution (telecommunication). LTE is a standard for wireless communication of high-speed data for mobile phones and data terminals. A life-saving feature that senses the radio user may be in trouble by monitoring the whether the radio is in a vertical or horizontal position or whether the radio is motionless. When this feature is triggered, the radio alerts the user with audio and visual alerts. It can also trigger Emergency Alarm the Post-Alert Timer is not cancelled. Mission Critical Wireless Ite1 IV & D KVL LCD LED Li-Ion LTE Man Down MCW Definition iosc Term A scan list that can include both talkgroups (trunked) and channels (conventional). Check channel activity by pressing the Monitor button. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed. } buttons. A software-activated feature shown at the bottom of the display – selection of these features is controlled by the {, |, and Motorola Data Communication Definition Operation Critical Wireless 173 English The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. Non-Tactical/ Revert OCW Nickel-metal-hydride. NiMH Network Access Code (NAC) operates on Network Access digital channels to reduce voice channel Code interference between adjacent systems and sites. Multi-System Talkgroup Scan List Monitor Menu Entry MDC Term Glossary A one-way alert, with audio and/or display messages. A set of unique features specific to a radio. Personal Identification Number A software application which streamlines critical real time operations and simplifies system administration to deliver accurate, consistent and integrated information remotely to the requestors. Refers to a software feature that has been activated by a qualified radio technician. A feature that lets you have a private conversation with another radio user in the talkgroup. A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Refers to a radio control that can have a radio feature assigned to it. Push-To-Talk – the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. Page Personality PIN PremierOne Preprogrammed Private (Conversation) Call Private Line (PL) Programmable PTT Definition Over-the-air rekeying. Term OTAR English 174 Glossary A feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you. A conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage. The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz). Definition SSI An operating condition whereby the radio’s speaker is muted but still continues to receive data. Synchronous Serial Interface Squelch Standby Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. Any digital P25 traffic having the correct Selective Switch Network Access Code and the correct talkgroup. Selective Call Repeater Radio Frequency (RF) Term Pre-defined text messages that allow the user to send a conditional message without talking. The user talks on the channel that was selected before the radio entered the emergency state. Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. An organization or group of radio users who communicate with each other using the same communication path. Text Messaging Service The automatic sharing of communications paths between a large number of users (see Conventional). A scan list that includes talkgroups that are all from the same trunking system. Unique Shadow Key. Tactical/ Non-Revert Talkaround Talkgroup TMS Trunking Trunking Priority Monitor Scan List USK Definition Status Calls Term Zone vpn1 UTC Term A grouping of channels. Adapter name used by the radio for encrypted LTE traffic 175 English Coordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich (up to 180 degrees) is later in time; everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other. Abbreviated as UTC (English backronym = Universal Time, Coordinated), it is also known as Zulu (Z) Time. Definition Glossary One (1) Year Product Accessories This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. One (1) Year ASTRO APX 7000/APX 7000L Portable Units MOTOROLA SOLUTIONS INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below: I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA COMMUNICATION PRODUCTS Limited Warranty Commercial Warranty English 176 Commercial Warranty This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR II. GENERAL PROVISIONS: MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. V. WHAT THIS WARRANTY DOES NOT COVER: You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service . Warranty service will be provided by MOTOROLA through one of its authorized warranty service s. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. IV. HOW TO GET WARRANTY SERVICE: This warranty gives specific legal rights, and there may be other rights which may vary from state to state. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. III. STATE LAW RIGHTS: CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. 177 English C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if: (1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering. (2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. Commercial Warranty MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim; B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. VI. PATENT AND SOFTWARE PROVISIONS: English 178 Commercial Warranty This Warranty is governed by the laws of the State of Illinois, U.S.A. VII. GOVERNING LAW: Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Motorola Solutions Australia’s limited warranty below is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: http://www.motorolasolutions.com/XA-EN/ Pages/Contact_Us for the most updated warranty terms. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is given by Motorola Solutions Australia Pty Limited (ABN 16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. VIII. FOR AUSTRALIA ONLY: English 179 Commercial Warranty Notes English 180 Commercial Warranty © 2009 – 2014 Motorola Solutions, Inc. All rights reserved. June 2014 G3-4-100 MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196, U.S.A. 6875945M01-M *6875945M01*
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Motorola Create Date : 2014:07:17 07:56:54-04:00 Modify Date : 2014:07:17 07:56:54-04:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Producer : Acrobat Distiller 11.0 (Windows) Creator Tool : FrameMaker 8.0 Metadata Date : 2014:07:03 15:50-04:00 Format : application/pdf Title : APX 7000/7000L Portable Dual Display User Guide Creator : Motorola Copyright : Copyright 2009 - 2011 by Motorola Solutions, Inc. Document ID : uuid:9a989f3a-6888-4496-befa-f2121d48d922 Instance ID : uuid:235cbcfc-6f82-41ab-851e-70f052ae031d Page Count : 204EXIF Metadata provided by EXIF.tools