Motorola Solutions 89FT7632 3630APC Outdoor Connectorized Access Point User Manual D0218 PMP 320

Motorola Solutions, Inc. 3630APC Outdoor Connectorized Access Point D0218 PMP 320

D0218 PMP 320 User manual

Download: Motorola Solutions 89FT7632 3630APC Outdoor Connectorized Access Point User Manual D0218 PMP 320
Mirror Download [FCC.gov]Motorola Solutions 89FT7632 3630APC Outdoor Connectorized Access Point User Manual D0218 PMP 320
Document ID1245297
Application IDbJCIIsZnYYg9VMnWhf2T1A==
Document DescriptionD0218 PMP 320 User manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize255.99kB (3199861 bits)
Date Submitted2010-02-25 00:00:00
Date Available2010-02-25 00:00:00
Creation Date2017-11-10 11:17:23
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-10 11:17:23
Document TitleD0218 PMP 320 User manual
Document CreatorAcrobat PDFMaker 8.1 for Word
Document Author: fsa011

PMP 320 Access Network
User Guide
Issue 2
November 2009
Notices
See important regulatory, legal, and safety notices in section 6 on page 18.
Trademarks, Product Names, and Service Names
MOTOROLA, the stylized M Logo, and all other trademarks indicated as such herein are
registered trademarks of Motorola, Inc. ® Reg. US Pat & Tm. Office. All other product or service
names are the property of their respective owners.
© 2009 Motorola, Inc. All rights reserved
http://motorola.wirelessbroadbandsupport
Table of Contents
1.0
Using This User Guide ............................................................................................. 4
1.1
FINDING THE INFORMATION YOU NEED ............................................................ 4
1.2
Becoming Familiar with This User Guide ............................................................ 4
1.3
Searching This User Guide .................................................................................. 5
1.4
Finding Parameter and Field Definitions for Module Web Pages ...................... 5
1.5
NEW PRODUCTS AND FEATURES DESCRIBED IN THIS ISSUE .............................. 5
1.6
NEW DESCRIPTIONS AND REVISIONS IN THIS ISSUE........................................... 5
1.7
PORTFOLIO OF WIRELESS BROADBAND SOLUTIONS.......................................... 5
1.8
PRODUCTS COVERED BY THIS USER GUIDE ........................................................ 6
1.9
PRODUCTS NOT COVERED BY THIS USER GUIDE ................................................ 6
1.10 CONVENTIONS .................................................................................................... 6
1.11 TECHNICAL SUPPORT .......................................................................................... 7
1.12 FEEDBACK ON DOCUMENTATION ...................................................................... 8
2 Product Description .................................................................................................... 9
2.1
Access Point (AP)............................................................................................... 11
2.2
Subscriber Module (SM) ................................................................................... 14
2.3
INSTALLING THE AP........................................................................................... 15
3 Regulatory, Legal, and Safety Notices ...................................................................... 19
3.1
IMPORTANT NOTE ON MODIFICATIONS .......................................................... 19
3.2
NATIONAL AND REGIONAL REGULATORY NOTICES.......................................... 19
3.3
RF EXPOSURE SEPARATION DISTANCES............................................................ 23
3.4
LEGAL NOTICES ................................................................................................. 25
3.5
LIMIT OF LIABILITY ............................................................................................ 27
4 Checking Software Version ....................................................................................... 28
4.1
Log into the AP GUI using the following procedure ......................................... 28
4.2
Check the current running version of the AP ................................................... 28
4.3
Check the current running version of software on the CPE ............................. 28
4.4
Upgrading to the latest Software Revision on the Access Point and the CPE .. 30
5 User Account Overview ............................................................................................ 40
5.1
AP User Accounts.............................................................................................. 40
5.2
CPE User Accounts ............................................................................................ 41
6 IP Configuration ........................................................................................................ 43
6.1
IP Overview ....................................................................................................... 43
6.2
Key IP guidelines ............................................................................................... 43
6.3
Configuring AP IP Settings................................................................................. 44
6.4
Configure the CPE IP Settings ........................................................................... 45
7 RF Parameter Configuration ..................................................................................... 48
7.1
AP RF Parameter Configuration (WiMAX Capabilities)..................................... 48
7.2
AP RF Parameter Configuration (Radio) ........................................................... 48
7.3
AP RF Parameter Configuration (Mode) ........................................................... 49
8 CPE RF Parameter Configuration .............................................................................. 50
8.1
CPE Frequency and Channel bandwidth Configuration.................................... 50
9 Authentication Configuration ................................................................................... 52
9.1
AP Authentication Parameter Configuration.................................................... 52
9.2
AAA Authentication Configuration ................................................................... 52
9.3
Aradial server installation (Refer to Appendix A for initial steps) .................... 53
9.4
Add a NAS.......................................................................................................... 54
9.5
Add a GROUP .................................................................................................... 56
9.6
Add a USER........................................................................................................ 58
9.7
Verification of AAA configuration ..................................................................... 61
9.8
Setting up CPE for Authentication .................................................................... 61
10
Quality of Service Configuration........................................................................... 63
10.1 Brief overview of the quality of service section ............................................... 63
10.2 QoS profile creation .......................................................................................... 63
10.3 Classification profile creation: .......................................................................... 65
10.4 Service flow creation: ....................................................................................... 66
11
Appendix A – AAA Server Installation................................................................... 68
12
Appendix B – Troubleshooting.............................................................................. 70
1.0 Using This User Guide
The audience for this document includes network planners, system operators,
network administrators, and equipment installers.
1.1 FINDING THE INFORMATION YOU NEED
1.2 Becoming Familiar with This User Guide
The Table of Contents provides not only a sequential index of topics but also a visual
glance at the organization of topics in this guide. A few minutes spent with the Table of
Contents in either the paper or the electronic version of this guide can save much more
time in finding information now and in the future. The List of Procedures may be
especially useful in the paper version of this guide, particularly where you mark those
procedures that you wish to frequently see.
In contrast, the List of Figures and List of Tables are most useful for automated searches
on key words in the electronic version of this guide. If a match is present, the match is
the first instance that the search finds.
Quick Reference
This user guide comprises six sections, as described in Table 1.
Section
Guide to This User
Guide
(this section)
Purpose
Identifies
products covered by this user guide.
products covered by their own separate user guides.
how this user guide is organized.
where to find module web pages and parameter descriptions.
what the various typefaces and admonitions indicate.
how to contact Motorola.
Product Description Provides
references to RF and networking theory.
overviews and comparisons of products and how they
communicate.
descriptions of data handling and synchronization.
a review of optional features. resources for developing
familiarity and proficiencies
Planning
Configuration
Provides essential information for
evaluating an area for a network.
specifying the IP addresses and frequencies to use.
Provides guidance for
expanding network coverage.
improving the security of wireless links.
distributing bandwidth resources
monitoring and changing variables through SNMP.
Installation
Reference
Information
Glossary
Provides systematic approaches for
avoiding hazards from RF and natural causes.
testing, storing, and deploying equipment.
Provides supplemental information such as
authorizations, approvals, and notices.
a bibliography of adjunctive information sources.
a history of changes in documentation.
Defines terms and concepts that are used in this user guide
1.3 Searching This User Guide
To search this document and the software release notes of supported releases, look in
the Table of Contents for the topic and in the Adobe Reader® search capability for
keywords that apply.1 These searches are most effective when you begin the search
from the cover page because the first matches may be in titles of sections, figures,
tables, or procedures.
1.4 Finding Parameter and Field Definitions for Module Web Pages
Because this user guide is sequentially arranged to support tasks, and various tasks
require different settings and readings, parameter and field definitions are scattered
according to the tasks that they support.
1.5 NEW PRODUCTS AND FEATURES DESCRIBED IN THIS ISSUE
This section is a placeholder where other new descriptions, as wells as clarifications and
corrections, will be listed in future issues.
1.6 NEW DESCRIPTIONS AND REVISIONS IN THIS ISSUE
This section is a placeholder where other new descriptions, as wells as clarifications and
corrections, will be listed in future issues.
1.7
PORTFOLIO OF WIRELESS BROADBAND SOLUTIONS
The Motorola portfolio of wireless broadband solutions provides a range of flexible,
interworkable, products
− licensed 802.16e point‐to‐multipoint solutions (PMP 320)
− unlicensed point‐to‐multipoint solutions (PMP 100, PMP 400)
− point‐to‐point solutions
− Enterprise Wireless LAN (WLAN) solutions
‐ Mesh, including the MOTOMESH series of products
‐ Wireless Manager, a network manager capable of managing many of these
elements
1.8 PRODUCTS COVERED BY THIS USER GUIDE
This user guide describes planning, configuration, installation, and operation of the CAP
320 (the Access Point member of the PMP 320 family) and also includes information to
help the operator plan and deploy a PMP 320 access network.
1.9 PRODUCTS NOT COVERED BY THIS USER GUIDE
Related PMP 320 Access Network devices have their own user guides: CSM 320, the
Cluster Management Module 4 (CMM4), Network Updater Tool (CNUT), and Wireless
Manager (WM).
1.10 CONVENTIONS
This document employs distinctive fonts to indicate the type of information, as
described in Table
1.11 TECHNICAL SUPPORT
Here is the escalation path for resolution of a problem:
1. Check this user guide
2. Consider checking the Community Forum and Knowledge Base at
http://motorola.wirelessbroadbandsupport.com/support/community.
3. Escalate the problem to your supplier or reseller.
4. Escalate the problem to Canopy Technical Support or other designated Tier 3
technical support:
U.S. and Canada Email: technical-support@canopywireless.com
1‐866‐961‐9288
Latin and Central America Email: technical‐support@canopywireless.com
Argentina 0800‐666‐2789
Brazil 0800‐891‐4360
Columbia 01‐800‐912‐0557
Mexico 001‐800‐942‐7721
Peru 0800‐70‐086
All other countries +420 533 336 946
Europe, Middle East, Email: essc@motorola.com
and Africa Denmark 043682114
France 0157323434
Germany 06950070204
Italy 0291483230
Lithuania 880 030 828
Netherlands 0202061404
Norway 24159815
Portugal 0217616160
Spain 0912754787
Russia 810 800 228 41044
Saudi Arabia 800 844 5345
South Africa 0800981900
United Kingdom 0203 0277499
Asia Pacific Email: WiBBsupport.apac@motorola.com
+6048503854 (9am ‐ 5pm Malaysia Time)
+420 533 336 946 (outside hours)
When you send e‐mail or call, please include, as appropriate, software release on each module,
IP addresses, MAC addresses, and features enabled.
1.12 FEEDBACK ON DOCUMENTATION
Is this document accurate, complete, and clear? How can it be improved? Send your feedback on
documentation to technical‐documentation@canopywireless.com.
Issue
2 Product Description
A PMP 320 Access Network provides a low cost point‐to‐multipoint broadband
infrastructure optimized for fixed outdoor applications. The access point is an 802.16e
micro base station with WiMAX CPE interoperability. The system offers an integrated,
all‐outdoor solution with simple installation for rapid deployment.
Target applications for the PMP 320 Access Network include
ƒ
Tier 2/tier 3 carriers, where the PMP 320 system provides a cost‐
effective, reliable broadband connectivity for residential and business
customers
ƒ
Government network operators, where the PMP 320 system provides
broadband‐based infrastructure for administrative networks
ƒ
Wireless service providers, with broadband network service for any
size operation
ƒ
Wireline service providers, with broadband wireless extensions for
existing DSL or cable networks.
As shown in Figure 1, a PMP 320 network consists of
ƒ
APs – CAP 320 Access Points, usually tower‐mounted in a four‐sector
configuration.
ƒ
SMs ‐ CSM 320 Subscriber Modules, Customer Premise Equipment
(CPE), usually mounted on a residence or other structure, and
powered by a power adapter providing standard 802.3af power over
Ethernet.
ƒ
CMM4 (Cluster Management Module 4) – a zero‐footprint enclosure
housing a GPS module connected to a GPS antenna, sync‐ and power‐
injection circuitry, surge protection, and a managed switch. The CMM
is used to provide custom “sync over power over Ethernet” to the APs
as well as offering a networked, managed switch.
High Level Network Diagram
Core
Network
Radio Access
Network
Internet
AP
CMM4
Router
(optional)
SMs
NMS (optional)
AAA Server
DHCP Server
(optional) (e.g., Wireless Manager) (optional)
DNS Server
(optional)
Figure 1: High level network diagram
In addition, a PMP 320 network usually also requires a
ƒ
AAA Server – Authentication, Authorization, and Accounting server
using the RADIUS (Remote Authentication Dial In User Service)
protocol
ƒ
EMS – an Element Management System, such the Motorola One Point
Wireless Manager
ƒ
DHCP Server – Dynamic Host Configuration Protocol server
ƒ
DNS Server – Domain Name System server
ƒ
CNUT – Network Update Tool for updating device software
Motorola offers PMP 320 equipment that operates in the spectrum ranges as shown in
Table 4
Licensed
Spectrum
Ranges
3.3 to 3.4
GHz
System Name
AP Name
SM Name
AP Model
Number
SM
Model
Number
Frequencies
Supported
PMP 35320
CAP 35320
CSM 35320
3530APC
3530SM
3.3 to 3.6 GHz
PMP 36320
CAP 36320
CSM 36320
3630APC
3630SM
3.6 to 3.8 GHz
(Includes 3.65
GHz)
3.4 to 3.6
GHz
3.6 to 3.8
GHz
10
2.1 Access Point (AP)
A PMP 320 Access Point (AP) is an 802.16e micro base station that connects wirelessly
to up to 200 PMP 320 Subscriber Modules (SMs) or WiMAX CPEs. The AP consists of a
connectorized antenna and radio, as shown in
Figure 2, with the radio shown separately in Figure 3. The standard antenna is a dual‐
polarity 16.5 dBi antenna typically mounted in a four 90° sector configuration. The AP is
manageable by local web interface, as well as SNMP or the Motorola One Point Wireless
Manager.
11
Figure 2: Access Point (AP)
Figure 3: AP, radio only
The PMP 320 AP uses 802.16e for the over‐the‐air connection to the SMs or CPE and is
802.16e PHY and MAC compliant. It complies with WiMAX Wave2 profile, except for
mobility.
The AP uses a custom 56 VDC power system, typically powered by a CMM4. The AP uses
less than 25 W per AP, or less than 100 watts for 360° coverage. The AP includes
integrated surge suppression that is the equivalent of the 600SS surge suppressor
recommended for SM installations.
The AP functions as a router in the network, with routes to the SMs auto‐configured. It
supports a configurable static routing table and the standard RIPv2 routing protocol.
The AP supports ICMP and ARP.
The AP can be configured to either receive its IP address from a network DHCP server, or
be manually assigned its IP address.
The AP can be configured to respond to SM DHCP requests either by relaying the
requests to a network DHCP server, or function as a DHCP server itself.
The AP can be configured either to use an external AAA (Authentication, Authorization,
and Accounting) server, or use a minimal internal AAA server. When configured to use
an external AAA server, the AP serves as a relay between SMs and the AAA server for
authentication requests, and serves as a RADIUS client communicating with the AAA
server for authorization of SM services.
The AP has an embedded web server for configuring using a web browser.
The AP supports SNMP v1 and v2c, and uses standard 802.16e MIBs (Management
Information Base) as well as the Motorola 802.16e AP MIB.
Specifications for the CAP 320 are listed in Table 1.
12
Table 1: CAP 320 Specifications
CAP 320
FREQUENCY
3.3 – 3.4 GHz
(CAP 33320)
3.4 – 3.5 GHz
(CAP 35320)
3.6 – 3.8 GHz
(CAP 36320)
PERFORMANCE
Physical Layer
802.16e‐2005 (5 MHz channel: 512 FFT; 7/10MHz
channel: 1024FFT)
MAC layer
802.16e‐2005
Maximum
Transmission
Power
Up to 2 x 25 dBm;
Maximum EIRP
Integrated: 2 x 41.5 dBm
Local Regulatory Requirements May Limit Max
Transmission Power.
See table 5 on page 19 for FCC limits in U.S. applications.
Connectorized: Antenna Dependant
Local Regulatory Requirements May Limit Max EIRP.
See table 5 on page 19 for FCC limits in U.S. applications
Maximum
Throughput per
Sector
Greater than 45Mbps total aggregate per sector
Packets per
Second
65,000
Maximum LoS
Range
Up to 40km with extended range feature
SPECTRUM
Frequency
Range of Band
3.3 – 3.4 GHz
3.4 – 3.6 GHz
Channel Width
Configurable to 5/7/10 MHz
3.6 – 3.8 GHz
SECURITY
Encryption
EAP‐TTLS/PKMv2 authentication over RADIUS, AES over‐
the‐air encryption
LINK BUDGET
Receive
Sensitivity
(10 MHz
channel); based
on MRCT
method
CTC‐QPSK(1/2): ‐103 dBm
CTC‐QPSK (3/4): ‐102 dBm
CTC‐16QAM(1/2): ‐101 dBm
CTC‐16QAM (3/4): ‐ 97 dBm
CTC‐64QAM(1/2): ‐ 96 dBm
CTC‐64QAM (2/3): ‐ 92 dBm
CTC‐64QAM(3/4): ‐ 91 dBm
CTC‐64QAM (5/6): ‐ 89 dBm
13
ANTENNA
Antenna Beam
Width
16.5 dBi gain Dual Polarity +/‐ 45 degree 4 sector
application (actual 3 dB antenna pattern: 60° horizontal
8° elevation)
PHYSICAL
Power
Consumption
< 25 Watts
Temperature
‐40° F to +131° F (‐40° C to +55° C)
Wind Survival
118 miles/hr (190 km/hr)
Dimensions
(LxWxD)
Integrated: ~711 x 195 x 240mm
Weight
Connectorized: ~330 x 195 x 140mm
Integrated: 5.5 kg
Connectorized: 2.2 kg
INTERFACE
Interface
10/100 Base T, half/full duplex. Rate auto negotiated
(802.3 compliant)
Protocols Used
IPv4, UDP, TCP, IP, ICMP, SNMP, HTTP, FTP, RIP, DHCP
Relay
Network
Management
Web‐Based Interface; SNMPv2c; or Motorola Wireless
Manager
CERTIFICATION
FCC ID
n/a
n/a
ABZ89FT7632
Industry Canada
Certification
Number
n/a
109W‐3530APC
109W‐3630APC
CE
"CE" marked & compliant to EN300 328. DoCs are
available at
http://motorola.wirelessbroadbandsupport.com/doc.ph
2.2 Subscriber Module (SM)
Please refer to the CSM35320 User Guide for further information on the Subscriber
Module
14
2.3 INSTALLING THE AP
General communications equipment, infrastructure, and facilities site design should be
performed
in line with Motorola’s “Standards and Guidelines for Communications Sites” (also
known as the
R56 manual) available from
http://www.motorola‐wls.com/Dynamic/Course_Description.asp?number=ANT001‐
CD&CourseKe
y=125
These procedures are specific to the case of as AP purchased as a kit consisting of a
connectorized antenna and a connectorized radio.
A short coaxial cable from the radio terminates in a male N connector. The antenna has
a chassis‐mounted female N connector. The antenna includes tower mount brackets
with adjustable down‐tilt.
Installing an AP typically consists of four phases:
1. Configure the AP at an operator's facility or at the installation site using the
information and settings defined in the Planning and Configuring sections of this user
guide.
2. Assemble the AP (radio, antenna, and brackets) and physically install it using
Procedure 2. A CMM4 is typically installed at the same time, if not previously
installed.
3. Cable the AP to the CMM4 and ground it to Protective Earth – PE using Procedure
4. This phase can also include cabling to backhauls, or running terrestrial feeds.
5. Confirm operation, using SMs in the field.
Local practices and choices of installation options will dictate the actual processes. For
example,
variations on these generalized procedures can be used to install on a building or install
multiple
APs on a pipe mount before hoisting up a tower for final attachment.
15
Procedure 1: Assembling an AP and attaching to tower
1.
Perform a parts check to
ensure all parts are present.
16
2.
Connect antenna brackets to
the antenna. Assemble with
the “scissor bracket” pointing
up (unlike in the
accompanying pictures) to
avoid physical interference
between the bracket and the
radio housing.
3.
Connect the radio to the
antenna by sliding it into the
captive space. Secure the
radio to the antenna using the
two bolts provided.
4.
Connect both coax N-connectors from the radio to the antenna. Connect the cable labeled
“main” to the antenna connector labeled “main”, and connect the cable labeled “Diversity”
to the antenna connector labeled “Diversity”.
17
5.
Using standard work and safety practices for tower climbing, connect the assembled unit
(assembled antenna, brackets, and radio) to a pole, mounting fixture, or the tower. Mount
the unit so as to avoid accidental touching by personnel. Typically this means mounting
the unit at least 4 m (13 ft) above ground level.
Procedure 2: Cabling and Grounding/Earthing the AP
Standard installation practices apply, including
use shielded Ethernet cable for all infrastructure cabling
use drip loops
provide extra cable (a splice loop) for future use at any termination
ensure the tower or structure is fully grounded (Protective Earth – PE)
1. Use dielectric grease (which is uniformly non-conducting) on all connections and in all
RJ-45 Ethernet connectors. The best practice is to use enough grease to fill the RJ-45
female connector, and then insert the RJ-45 male connector and push the grease
further into the unit and around the RJ-45 connector. Excess grease can be wiped over
the connector area to provide some resistance to water ingress around the connector.
Run a 10 AWG ground strap from the ground lug on the AP (see Error! Reference source not
found.) to known good ground (Protective Earth - PE).
The AP has metal‐to‐metal contact from the tower or support structure, through the antenna,
through the coax cable, to the radio. Installing surge suppression at the AP is strongly
recommended to provide the best protection from nearby lightning strikes.
Up to four 600SS surge suppressors may be mounted in series on an Ethernet link without
degrading the link. The equivalent of a 600SS is built into each of the 8 ports on a CMM4 and
counts as one of the four.
As an example, a typical installation might have properly‐grounded 600SS units within 3 ft (1 m)
of each AP and additional properly‐grounded 600SS units on each Ethernet cable mounted
outside at the point of cable entry to a telecommunications hut that contains the CMM4.
18
3 Regulatory, Legal, and Safety Notices
3.1
IMPORTANT NOTE ON MODIFICATIONS
Intentional or unintentional changes or modifications to the equipment must not be made unless
under the express consent of the party responsible for compliance. Any such modifications could
void the user’s authority to operate the equipment and will void the manufacturer’s warranty.
3.2 NATIONAL AND REGIONAL REGULATORY NOTICES
3.2.1 U.S. Federal Communication Commission (FCC) Notification
This device complies with Part 15 of the US FCC Rules and Regulations. Operation is
subject to
the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the US FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio‐frequency energy and, if not installed
and used in accordance with these instructions, may cause harmful interference to radio
communications. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the
user is encouraged to correct the interference by one or more of the following
measures:
•
•
Increase the separation between the affected equipment and the unit;
Connect the affected equipment to a power outlet on a different circuit from
that which the receiver is connected to;
• Consult the dealer and/or experienced radio/TV technician for help.
FCC IDs and the specific configurations covered are listed in Table 5.
19
Table 5: US FCC IDs and covered configurations
FCC ID
ABZ89FT7632
Operating
Freq
3.650 to 3.675
GHz
Model Number
3630APC
Antenna Gain
Channel Size
Maximum
Transmitter
Output Power
10 MHz
22.91 dBm
7 MHz
21.35 dBm
5 MHz
19.81 dBm
3.5 MHz
18.33 dBm
16.5dBi
3.2.2 Industry Canada Notification
This device is approved for use in Canada in the licensed frequencies from 3.450 GHz to
3.650 GHz. It is undergoing Industry Canada approval for use in the 3.65 GHz band, and
may not be used in that band until Industry Canada approval is granted.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio‐frequency energy and if not installed and used in accordance with these
instructions, may cause harmful interference to radio communications. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment on and off, the user is encouraged to correct
the interference by one or more of the following measures:
•
Increase the separation between the affected equipment and the unit;
•
◦ Connect the affected equipment to a power outlet on a different circuit from
that which the receiver is connected to;
•
Consult the dealer and/or experienced radio/TV technician for help.
To reduce potential radio interference to other users, the antenna type and its gain
should be chosen so its Equivalent Isotropic Radiated Power (EIRP) is not more than that
permitted for successful communication.
20
Industry Canada Certification Numbers and the specific configuration covered are listed
in Table 6.
Table 2: Industry Canada Certification Numbers and covered configurations
ID
TBD
Operating
Freq
3.650 to
3.675 GHz
Model
Number
3630APC
Antenna
Gain
Channel
Size
Maximum allowed
EIRP
Maximum
Transmitter
Output
Power
10 MHz
10 W (40 dBm)
23.5 dBm
7 MHz
7 W (38.5 dBm)
22 dBm
5 MHz
5 W (37 dBm)
20.5 dBm
3.5 MHz
3.5 W (35.4 dBm)
18.9 dBm
16.5 dBi
109W‐
3530APC
3.450 to
3.600 GHz
3530APC
16.5 dBi
connect
orized
any
na
27 dBm
(500 mW)
109W‐
3630APC
3.600 to
3.650 GHz
3630APC
16.5 dBi
connect
orized
any
na
27 dBm
(500 mW)
3.2.3 6.2.3 European Union Notification
The relevant Declaration of Conformity can be found at
http://motorola.wirelessbroadbandsupport.com/doc.php.
3.2.4 6.2.4 Equipment Disposal
Please do not dispose of Electronic and Electric Equipment or Electronic and Electric
Accessories with your household waste. In some countries or regions, collection systems
have been set up to handle waste of electrical and electronic equipment. In European
Union countries, please contact your local equipment supplier representative or service
center for information about the waste collection system in your country.
21
3.2.5 EU Declaration of Conformity for RoHS Compliance
Motorola hereby, declares that these Motorola products are in compliance with the
essential requirements and other relevant provisions of Directive 2002/95/EC,
Restriction of the use of certain Hazardous Substances (RoHS) in electrical and electronic
equipment.
The relevant Declaration of Conformity can be found at
http://motorola.wirelessbroadbandsupport.com/doc.php.
3.2.6 Labeling and Disclosure Table for China
The People’s Republic of China requires that Motorola’s products comply with China
Management Methods (CMM) environmental regulations. (China Management
Methods refers to the regulation Management Methods for Controlling Pollution by
Electronic Information Products.)
Two items are used to demonstrate compliance ‐ the label, and the disclosure table as
shown in
Table 7. [Need updated table for this product.]
The label is placed in a customer visible position on the product.
• Logo 1 means that the product contains no substances in excess of the maximum
concentration value for materials identified in the China Management Methods
regulation.
• Logo 2 means that the product may contain substances in excess of the maximum
concentration value for materials identified in the China Management Methods
regulation, and has an Environmental Friendly Use Period (EFUP) in years, fifty years
in the example shown.
The Environmental Friendly Use Period (EFUP) is the period (in years) during which the Toxic and
Hazardous Substances (T&HS) contained in the Electronic Information Product (EIP) will not leak or
mutate causing environmental pollution or bodily injury from the use of the EIP. The EFUP indicated by
the Logo 2 label applies to a product and all its parts. Certain field‐replaceable parts, such as battery
modules, can have a different EFUP and are marked separately.
The Disclosure table is intended to communicate compliance with only China requirements; it is not
intended to communicate compliance with EU RoHS or any other environmental requirements.
22
3.3 RF EXPOSURE SEPARATION DISTANCES
To protect from overexposure to RF energy, an AP must be installed to provide a
separation distance of at least 52 cm ( ~20 in) from all persons In addition, do not
collocate within 20 cm (4 in) of any other antenna or transmitter.
The following section and Table 8 provide details and discussion on the separate
distance calculations.
3.3.1 Details of Exposure Separation Distances Calculations and
PowerCompliance Margins
Limits and guidelines for RF exposure come from:
• US FCC limits for the general population. See the FCC web site at
http://www.fcc.gov, and the policies, guidelines, and requirements in Part 1 of
Title 47 of the Code of Federal Regulations, as well as the guidelines and
suggestions for evaluating compliance in FCC OET Bulletin 65.
• Health Canada limits for the general population. See the Health Canada web
site at http://www.hc‐sc.gc.ca/rpb and Safety Code 6.
• ICNIRP (International Commission on Non‐Ionizing Radiation Protection)
guidelines for the general public. See the ICNIRP web site at
http://www.icnirp.de/ and Guidelines for Limiting Exposure to Time‐Varying
Electric, Magnetic, and Electromagnetic Fields.
The applicable power density exposure limits from the documents referenced above is
10 W/m2.
Peak power density in the far field of a radio frequency point source is calculated as
follows:
23
Table 8 shows calculated minimum separation distances d, recommended distances and
resulting power compliance margins for each frequency band and antenna combination.
Table 8. Calculated exposure distance and power compliance margins
Band
Unit
3.3 GHz to 3.8
GHz
3.650 to 3.675
GHz (FCC Power
Limits)
AP
AP
0.5 W
(27
dBm)
.195W
(22.91
dBm)
Recom‐
mended
Separation
Distance
Power
Compliance
Margin
Variable
(calculated)
44.7
(16.5 dB)
10
W/m²
42 cm
52cm
(~20 in)
1.5
44.7
(16.5 dB)
10
W/m²
26.4 cm
52cm
(~20 in)
3.9
These are conservative distances:
ƒ
They are along the beam direction (the direction of greatest energy).
Exposure to the sides and back of the module is significantly less.
ƒ
In the case of collocated APs, they assume all APs are oriented in the
same direction, which is a worst‐case calculation.
ƒ
They meet or exceed sustained exposure limits for the general
population (not just short‐term occupational exposure limits).
ƒ
The calculated compliance distance d is overestimated because the
far‐field equation models the antenna(s) as a point source and
neglects the physical dimension of the antenna(s).
24
3.4 LEGAL NOTICES
3.4.1 Software License Terms and Conditions
ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT
THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU
USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE
AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR
RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL
REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN
INDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO
USE THIS PRODUCT IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE
FOLLOWING TERMS.
Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good
and valuable consideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and
Motorola agree as follows:
Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal,
revocable, non‐assignable, non‐transferable, non‐exclusive and limited license to use on a single piece of
equipment only one copy of the software contained on this disk (which may have been pre‐loaded on the
equipment)(Software). You may make two copies of the Software, but only for backup, archival, or disaster
recovery purposes. On any copy you make of the Software, you must reproduce and include the copyright
and other proprietary rights notice contained on the copy we have furnished you of the Software.
Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the
Software and any copies,
including translations, compilations, derivative works (including images) partial copies and portions of
updated works. The Software is Motorola’s (or its supplier's) confidential proprietary information. This
Software License Agreement does not convey to you any interest in or to the Software, but only a limited
right of use. You agree not to disclose it or make it available to anyone without Motorola’s written
authorization. You will exercise no less than reasonable care to protect the Software from unauthorized
disclosure. You agree not to disassemble, decompile or reverse engineer, or create derivative works of the
Software, except and only to the extent that such activity is expressly permitted by applicable law.
Termination. This License is effective until terminated. This License will terminate immediately without
notice from Motorola or judicial resolution if you fail to comply with any provision of this License. Upon such
termination you must destroy the Software, all accompanying written materials and all copies thereof, and
the sections entitled Limited Warranty, Limitation of Remedies and Damages, and General will survive any
termination.
Limited Warranty. Motorola warrants for a period of ninety (90) days from Motorola’s or its customer’s
shipment of the Software to you that (i) the disk(s) on which the Software is recorded will be free from
defects in materials and workmanship under normal use and (ii) the Software, under normal use, will
perform substantially in accordance with Motorola’s published specifications for that release level of the
Software. The written materials are provided "AS IS" and without warranty of any kind. Motorola's entire
liability and your sole and exclusive remedy for any breach of the foregoing limited warranty will be, at
Motorola's option, replacement of the disk(s), provision of downloadable patch or replacement code, or
refund of the unused portion of your bargained for contractual benefit up to the amount paid for this Software
License.
THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY MOTOROLA, AND MOTOROLA
AND ITS LICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OF
IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. MOTOROLA DOES NOT
WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERRORFREE,
OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. NO ORAL OR WRITTEN
REPRESENTATIONS MADE BY MOTOROLA OR AN AGENT THEREOF SHALL CREATE A WARRANTY
OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. MOTOROLA DOES NOT WARRANT
ANY SOFTWARE THAT HAS BEEN OPERATED IN EXCESS OF SPECIFICATIONS, DAMAGED,
MISUSED, NEGLECTED, OR IMPROPERLY INSTALLED. BECAUSE SOME JURISDICTIONS DO NOT
25
ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU.
Limitation of Remedies and Damages. Regardless of whether any remedy set forth herein fails of its
essential purpose, IN NO EVENT SHALL MOTOROLA OR ANY OF THE LICENSORS, DIRECTORS,
OFFICERS, EMPLOYEES OR AFFILIATES OF THE FOREGOING BE LIABLE TO YOU FOR ANY
CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR SIMILAR DAMAGES WHATSOEVER
(including, without limitation, damages for loss of business profits, business interruption, loss of business
information and the like), whether foreseeable or unforeseeable, arising out of the use or inability to use the
Software or accompanying written materials, regardless of the basis of the claim and even if Motorola or a
Motorola representative has been advised of the possibility of such damage. Motorola's liability to you for
direct damages for any cause whatsoever, regardless of the basis of the form of the action, will be limited to
the price paid for the Software that caused the damages. THIS LIMITATION WILL NOT APPLY IN CASE
OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAW REQUIRES
SUCH LIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
Maintenance and Support. Motorola shall not be responsible for maintenance or support of the software.
By accepting the license granted under this agreement, you agree that Motorola will be under no obligation
to provide any support, maintenance or service in connection with the Software or any application developed
by you. Any maintenance and support of the Related Product will be provided under the terms of the
agreement for the Related Product.
Transfer. In the case of software designed to operate on Motorola equipment, you may not transfer the
Software to another party except: (1) if you are an end‐user, when you are transferring the Software together
with the Motorola equipment on which it operates; or 2) if you are a Motorola licensed distributor, when you
are transferring the Software either together with such Motorola equipment or are transferring the Software
as a licensed duly paid for upgrade, update, patch, new release, enhancement or replacement of a prior
version of the Software. If you are a Motorola licensed distributor, when you are transferring the Software as
permitted herein, you agree to transfer the Software with a license agreement having terms and conditions
no less restrictive than those contained herein. You may transfer all other Software, not otherwise having an
agreed restriction on transfer, to another party. However, all such transfers of Software are strictly subject to
the conditions precedent that the other party agrees to accept the terms and conditions of this License, and
you destroy any copy of the Software you do not transfer to that party. You may not sublicense or otherwise
transfer, rent or lease the Software without our written consent. You may not transfer the Software in
violation of any laws, regulations, export controls or economic sanctions imposed by the US Government.
Right to Audit. Motorola shall have the right to audit annually, upon reasonable advance notice and during
normal business hours, your records and accounts to determine compliance with the terms of this
Agreement.
Export Controls. You specifically acknowledge that the software may be subject to United States and other
country export control laws. You shall comply strictly with all requirements of all applicable export control
laws and regulations with respect to all such software and materials.
US Government Users. If you are a US Government user, then the Software is provided with
"RESTRICTED RIGHTS" as set forth in subparagraphs (c)(1) and (2) of the Commercial Computer
Software‐Restricted Rights clause at FAR 52 227‐19 or subparagraph (c)(1)(ii) of the Rights in Technical
Data and Computer Software clause at DFARS 252.227‐7013, as applicable.
Disputes. You and Motorola hereby agree that any dispute, controversy or claim, except for any dispute,
controversy or claim involving intellectual property, prior to initiation of any formal legal process, will be
submitted for non‐binding mediation, prior to initiation of any formal legal process. Cost of mediation will be
shared equally. Nothing in this Section will prevent either party from resorting to judicial proceedings, if (i)
good faith efforts to resolve the dispute under these procedures have been unsuccessful, (ii) the dispute,
claim or controversy involves intellectual property, or (iii) interim relief from a court is necessary to prevent
serious and irreparable injury to that party or to others.
General. Illinois law governs this license. The terms of this license are supplemental to any written
agreement executed by both parties regarding this subject and the Software Motorola is to license you under
it, and supersedes all previous oral or written communications between us regarding the subject except for
such executed agreement. It may not be modified or waived except in writing and signed by an officer or
other authorized representative of each party. If any provision is held invalid, all other provisions shall
26
remain valid, unless such invalidity would frustrate the purpose of our agreement. The failure of either party
to enforce any rights granted hereunder or to take action against the other party in the event of any breach
hereunder shall not be deemed a waiver by that party as to subsequent enforcement of rights or subsequent
action in the event of future breaches.
3.4.2 Hardware Warranty in US
Motorola US offers a warranty covering a period of 1 year from the date of purchase by
the customer. If a product is found defective during the warranty period, Motorola will
repair or replace the product with the same or a similar model, which may be a
reconditioned unit, without charge for parts or labor.
3.5 LIMIT OF LIABILITY
IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT,
INDIRECT, GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER DAMAGE
ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF
BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS, OR FROM ANY BREACH OF
WARRANTY, EVEN IF MOTOROLA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
(Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
exclusion or limitation may not apply to you.) IN NO CASE SHALL MOTOROLA’S LIABILITY EXCEED THE
AMOUNT YOU PAID FOR THE PRODUCT.
27
4 Checking Software Version
4.1 Log into the AP GUI using the following procedure
Set your PC’s static IP to the same subnet as the AP default IP address of
“192.168.2.101
Connect the PC to the AP and use Internet Explorer version 7 or greater to launch
a web GUI. In the URL type http://192.168.2.101
4.2 Check the current running version of the AP
Log into the AP using “admin” as log in and “admin” as password
Go to home and take note of the version running per the figure below
4.3 Check the current running version of software on the CPE
Set your PC’s static IP to the same subnet as the CPE’s default LAN IP address of
“10.1.1.254”
Using a web browser, navigate to the CPE’s default IP at http://10.1.1.254
Login in as “admin”, password “admin” and take note of the software version
according to the figure below
28
29
4.4 Upgrading to the latest Software Revision on the Access Point and
the CPE
4.4.1 Updating your devices
In order to update your PMP320 devices you will need to download and install the latest
version (currently 3.2.7) of the Canopy Network Updating Tool (CNUT) as well as the
latest firmware package files (pkg3) for the AP and the SM (CPE).
Starting the CNUT application:
Start Æ Programs Æ Canopy Æ Network Updater 3.2 Æ Network updater
30
4.4.2 Adding your PMP320 AP(s) into CNUT
Edit Æ Add Canopy Element to Network Root
Select “PMP 300 Access Point (PMP)
Uncheck “Use Default/Inherit Settings from Parent Element”
Use “admin” for the Telnet/FTP login ID
Use “admin” for the Telnet/FTP Password
Use “admin_admin” for the SNMP Community String
Use “v1” for the SNMP Version
Provide the IP(s) of your AP’s
Hit “ok”
31
Adding your SM/CPE(s) into CNUT:
Edit Æ Add Canopy Element to Network Root
Select “PMP 300 SM (CPE)
Uncheck “Use Default/Inherit Settings from Parent Element”
Use “admin” for the Telnet/FTP login ID
Use “admin” for the Telnet/FTP Password
Use “private” for the SNMP Community String
Use “v1” for the SNMP Version
Provide the IP(s) of your CPE(s)
Hit “ok”
Refresh the recently added elements and verify if the Software Version requires
upgrading.
32
33
4.4.3 Managing CNUT packages
Update Æ Manage Packages
Click on Add
Select the PMP320AP (primary and backup) and PMP320SM pkg3 files and hit
“Open”
Verify that the packages have been added:
34
Upgrading the backup image on your AP:
Select the backup AP pkg3 file:
Update Æ Manage Packages
35
Select your AP(s)
Update Æ Update Selected Network Elements
36
Upgrading the primary image on your AP
Select the primary AP pkg3 file:
Verify that your AP(s) are still selected
Update Æ Update Selected Network Elements
37
Upgrading your CPE(s)
Select the CPE pkg3 file
Select your CPE(s)
38
Update Æ Update Selected Network Elements
Verify that your devices are on the current software:
39
5 User Account Overview
5.1 AP User Accounts
The access point supports the following two user account levels
Admin User Level: The admin user account is pre‐configured from the factory with the
default password of “admin”. This privilege level is targeted towards the service
provider/operator/ who is in charge of managing the entire network. This is also the
level used for initial discovery of the AP via the Wireless Manager and is the default
username, password in the community string
Login: admin
Password: admin
Installer User Level: The installer user account is also pre‐configured from the factory
with the default user level password “super”. This level of privilege is available and
targeted towards the installer who will actually be installing the access point on the
tower. It is assumed that the installer may be a sub contractor and may not require the
full levels of permission that the admin user provides.
Login: installer
Password: super
In order to create additional users follow the steps below:
Log into the AP GUI via your web browser
Go to “administration” on the left hand size of the menu
In the main screen, populate the user name, password, user level and status and
press “add” below. This will create the new user account and set the status and
level.
As an admin user level you are allowed to create up to 10 different combinations of
admin or installer accounts.
40
AP User Account Screen
5.2 CPE User Accounts
The following user levels are pre‐configured from the factory for the CPE
Admin level login for the home/end user
Login: admin
Password: admin
This user level is provided for the end user of the CPE and does not carry the same level
of access as the operator/service provider
Operator level login for the service provider
Login: operator
Password: operator
41
This user level is provider for the operator/service provider to access further parameters
of the CPE for debugging/configuration purposes.
42
6
IP Configuration
6.1
IP Overview
In the PMP320 system, there are three interfaces that need to have IP addresses
intelligently assigned to them in order for the system to operate properly. The three
interfaces are: 1) The APs wired (GMAC) and 2) wireless (WMAC) interfaces, and 3) the
CPEs wireless (WLAN) interfaces. The two AP interfaces can either be statically assigned
via the GUI or SNMP, or they can be set via an external DHCP server. The CPE WAN
interfaces must be assigned via DHCP in order for the AP to properly route user traffic to
the correct CPE.
The recommended configuration is to set up static reservations for the AP’s two
interfaces on an external DHCP server so that all AP IP addresses can be centrally
controlled and changed if necessary. Although these addresses are being set via a DHCP
server, it is important to note that the AP will not attempt to renew these addresses
unless the AP is rebooted. In general, there should not be a need for an APs GMAC and
WMAC interfaces to change once the network design has been completed.
In order to set the CPE WAN IP addresses, either the AP’s internal DHCP server can used,
or, the AP can act as a DHCP relay agent and relay DHCP requests to the external DHCP
server.
If the internal DHCP server is used, the AP can either handout addresses from a general
pool, or the AP can be configured to use static reservations based on the MAC address
of the requesting CPE.
When the external DHCP server is used, the server should be setup so that an unique
address pool is allocated for each AP. As previously mentioned, one address in each
pool should be statically reserved for each AP’s WMAC interface. When the AP forwards
the CPE’s DHCP request to the DHCP server, it will set the gateway address in the
request message to it’s WMAC IP address. The DHCP server will use the gateway
address to determine which of it’s configured IP pools to use in order to service this
request. The end result is that the CPEs will receive DHCP IP addresses on the same
subnet as the WMAC IP address of the AP that they are registered to.
6.2 Key IP guidelines
•
•
The AP’s Wired and Wireless interface must be on different subnets.
Static reservations must be made for the AP’s wireless(WMAC) and
wired(GMAC) interface
43
•
•
•
Infinite lease time must be configured for the static reservations
CPEs WAN interface IP must be assigned via DHCP
All CPEs under an AP must have their WAN IP on the same subnet as the AP’s
wireless interface.
6.3 Configuring AP IP Settings
Log into the AP Gui via a web browser
Go to General Æ IP Configuration
The two entries for Wireless and Wired will be pre‐configured from the factory
Select Wireless and then Wired and in each case choose DHCP client to “enable”
mode. Hit “update”
Top right corner hit the disc icon to save the configuration. The disc changes to
blue indicating that a configuration save is required
Following the configuration save, the icon to the right will change to yellow
indicating that a reboot is required. Hit the icon to reboot the radio.
IP Interface Configuration
Configure the DHCP server address in the DHCP Relay configuration
Go to Configuration Æ DHCP Server Æ DHCP Relay
Enter the external DHCP server IP address
Enter the Relay Maximum Wait time and Relay number of Retries
44
Go to “configuration” Æ Networking Æ and configure the following:
Enter the “default gateway”, “syslog IP”, DNS server IP and choose the
appropriate status for the above
Add NTP server IP addresses
6.4 Configure the CPE IP Settings
Log into the CPE using “operator” and password “wimax”
Go to NAT Mode once you are logged in and configure LAN IP address and LAN
netmask. You have the option to choose a different LAN network for devices
below your CPE
45
Go to DHCP Server page, configure DHCP start IP address and end IP address.
Configure Domain name and Max lease time.
46
Go to Port Forwarding page and configure the necessary ports you would like to
forward and enable them accordingly
Go to Firewall Page and configure the CPE Access control items. In addition,
configure the DMZ host IP if necessary.
47
7 RF Parameter Configuration
7.1 AP RF Parameter Configuration (WiMAX Capabilities)
Log into the AP gui per section xxx
Go to ÆConfiguration Æ Air Interface Æ WiMAX
Capabilities
Configure Access Point BSID with the MAC address of the
AP
Configure Center frequency
Hit update
7.2 AP RF Parameter Configuration (Radio)
Log into the AP gui per section xxx
Go to ÆConfiguration Æ Air Interface Æ Radio
Configure the Tx Power, Antenna gain, Direction and Antenna Height. Hit update
48
7.3 AP RF Parameter Configuration (Mode)
Go to ÆConfiguration Æ Air Interface Æ Mode
Configure the Selected channel bandwidth and Downlink/Uplink Ratio. Hit update
49
8 CPE RF Parameter Configuration
8.1 CPE Frequency and Channel bandwidth Configuration
Log into the CPE using the “admin” or “operator” login
Click on “WiMAX” and then click on “scanner”
Click on “edit” and add the desired frequency and channel bandwidth
Configure additional information under the “date” tab or refer to the CSM35320
CPE User Guide
50
51
9 Authentication Configuration
9.1 AP Authentication Parameter Configuration
Log into the AP and launch the web GUI using “admin” for both log in and
password
Navigate from the left side menu to “Configuration” Æ “General” Æ “Settings”
Choose the operational mode to be “External AAA”
On the right hand side populate with the following information
•
•
•
•
•
•
AAA Server IP
AAA Server port
AAA Client port
AAA NAS Name (Note: This will also need to be populated in the AAA)
Shared Secret (Note: This will also need to be populated in the AAA)
Choose “yes” or “no” for allowing unauthorized subscribers.
9.2 AAA Authentication Configuration
Note: Both the Aradial AAA and Free Radius AAA is supported with the PMP320 product
but only the Aradial configuration is noted in this user guide
52
9.3 Aradial server installation (Refer to Appendix A for initial steps)
From the Aradial installation folder, click on the Aradial installation executable
(Appendix A ‐ e.g. AradialSetup‐5‐1‐10.EXE).
In the screen mentioning the license mode (by default Demo mode), choose
"Registered mode".
In the screen demanding to enter the name of the server, the administration
username and password, enter the input of your choice.
After setup is completed, restart of the computer is required.
After restart, the WEB admin window of the Aradial is opened automatically. Log
in with the administration username/password you chose.
On the right side of the window, in the "STATISTICS" tab, press the "show" button
for "users in the database" and delete the dummy users registered.
Do the same for the "Network Access Servers configured".
53
From the Aradial installation folder, click on the ARDKEY.reg file, in order to
register the license key in the Windows registry.
Open the directory where Aradial is installed. By default it is "C:\Program
Files\Aradial". In the Aradial installation folder open the Aradial_cfg folder. Copy
from there in " C:\Program Files\Aradial", the DemoCerts folder (that contains
the Free radius server certificates we used before Aradial was available), the
eap_cfg.xml file (that defines the preferred EAP method, in our case TTLS) and
the eap_tls_cert_cfg.xml file (that defines the path to the certificates, in our
case, the DemoCerts folder).
Copy the NasCfgDbs file (containing all the NAS the server supports, we added
DAN NAS with the services level this NAS supports as example), and the DAN.dic
file (containing the VSA attributes definition), into the "C:\Program
Files\Aradial\RadDb" directory.
In the Windows services window, restart all the Aradial related services.
9.4
Add a NAS
54
Click on the NAS&Proxy tab. Click on the "Net. Access Server" add button. Fill the
NAS Name field with the same NAS name configured in the PMP320AP (Access
Point) in the configuration parameter.
Set the IP address of the GMAC interface of the PMP320AP in the IP Address
field.
Fill the secret and Confirm secret fields with the configured secret in the
PMP320AP by the configuration parameter.
In the Model field, choose the DAN model in the list.
Click the "ADD" button.
55
9.5
Add a GROUP
Click on the Home tab. Click on the "Group" add button. Fill the Group
Name field with a name in relation with the service level this group will
provide.
56
Choose from the list, one of the service type defined by DAN in the NasCfgDbs
file. For example: WimaxGold.
In the IP Pools list, choose NAS, and click "ADD".
The Password Source field should remain as the default, ie: 
Click the "Add" button in the bottom of the page.
57
9.6 Add a USER
Click on the Home tab. Click on the "User" add button. Fill the User Id and
Password fields with the username and password which CPE will use for
authentication and authorization.
Password Source should remain the same as the default to be , means
that the password policy is defined in the Group definition.
58
In the Association fields, choose in the Group list, the group you want the user to
be associated with.
(Optional step) You could fill the Caller Id field with the GMAC MAC address of
the AP, so this user will be authorized and provisioned only in the case it got
connected via this specific NAS (PMP320AP).
59
Check the "Active" checkbox, and the "Add" button in the bottom of the page.
60
9.7 Verification of AAA configuration
In the PMP320AP, be sure the authentication feature is enabled.
With Wireshark, be sure the Radius negotiation between the Aradial server and
the PMP320AP, is ending by a Radius Accept packet.
Start the CPE and observe it's getting authenticated and enters the network
successfully.
Observe after network entry that the CPE is getting provisioned via VSA messages
sent from the Aradial server through the AP, according to the group the CPE (user)
is associated to and the level of service defined for this group.
9.8 Setting up CPE for Authentication
Under Authentication section select EAP‐TTLS and MSCHAPV2.
Enter Username and Password that you created during Aradial configuration.
Uncheck use device certificates. For Identity you can check Random identity or for
ease in troubleshooting can define you own identity. Uncheck realm portion.
CPE comes with Motorola created CA certificate and Wimax forum CA certificate.
If you decide to use you own certificates you can upload them in this section.
Under Certification File Upload section, browse to the folder where you have you
CA certificate and upload it. Once the certificate is uploaded you should be able to
see it.
Update the DemoCerts folder located in “C:\Program Files\Aradial", with your
own Server and CA certificate. Also make necessary changes to eap_cfg.xml file.
Refer to Section “1 – Aradial server installation (Appendix A)” for more
information.
Check “Validate the date duration of CA certificate” and “Validate the server
certificate”.
Save the changes and reboot the CPE.
61
62
10 Quality of Service Configuration
10.1 Brief overview of the quality of service section
PMP320 provides different quality of service (QOS) settings per the 802.16e
specification e.g UGS, rtPS, nrtPS and BE. User can choose the appropriate QoS
profile based on the application needs. It is recommended that each QoS profile is
created with specific Maximum Information Rate (MIR) and Committed
Information Rate (CIR) as dictated by the application needs. The PMP320 system
can support several QoS profiles (e.g. 256) with different combinations of QoS
types, MIR and CIR.
Each PMP320AP serves several CPEs under given sector. Each CPE could have
multiple service flows in both UL and DL direction. Each flow is associated with a
given QoS profile which is configured based on end user need. One CPE could have
multiple flows to serve different applications simultaneously. To differentiate
multiple flows under a single CPE, PMP320 uses classification profiles. These
classification profiles are associated with specific service flows. Different
applications, both over UL and DL can send their data using classifications which
helps CPE and AP to associate data traffic to specific service flow with QoS type.
PMP320 supports source/destination IP address and TOS/DSCP (Diff Serve Code
Point) classifications.
10.2 QoS profile creation
Create/Add/Update/Delete additional QoS profiles using AP GUI, “Configuration”
Æ “QoS Profile”. AP will have QoS profile number 0 and 1 created by default
which is fixed. One can add different QoS profile as needed.
To add a new QoS profile, provide the new index, name if needed, selection of
HARQ, # Retries, security enabled or disable, DSCP marking disable or enable,
appropriate DSCP mark value (e.g TOS value) if DSCP Marking is enabled.By
default, HARQ is enabled with retries ”0”, Security and DSCP Marking is disabled.
Recommended configuration for the DL flow is HARQ enabled with retry “0” and
for the UL flow is HARQ disabled.
63
Upon creation of new profile, go on the Advanced tab
And update the appropriate values for the “Max Sustained Rate” and “Data
Delivery Type”.
If the nrtPS is selected as the “Data Delivery Type”, provide “Unsolicited poll
interval” e.g 150ms and “Min Reserved Rate” as needed. Polling interval
value is not needed for DL flow.
If the rtPS is selected as the “Data Delivery Type”, provide “Unsolicited poll
interval” e.g 60ms, appropriate “Min Reserved Rate” and “Max Latency”
value. Polling interval value is not needed for DL flow.
If the UGS is selected as the “Data Delivery Type” , provide “Unsolicited
Grant Interval” e.g 40ms and “Min Reserved Rate” same as “Max Sustained
Rate”.
64
After network entry to get an IP address. AP will use the default parameters to
create a service flows. By default, QoS profile “0” and “1” is configured for that,
as shown in picture below. One can use the different QoS profile by changing
these values to other QoS profile indexes.
10.3 Classification profile creation:
Create (Add)/Update/Delete classification profiles using AP GUI, “Configuration”
Æ “Classification Rules”.
65
To add or update, select or update the specific profile index under “Profile”,
select the “Type” and provide “ToS” or “IP Address” and IP Mask Length”. Do not
enter the rule ID until unless you want to create multiple rules for given profile,
rules are not needed on the normal basis.
10.4 Service flow creation:
AAA will be provide VSA information to create different service flow(s) for the
CPE based on the username and password configured on the CPE for
authentication. User profile is created at AAA (described at 10.6.1) with this
username and password
Upon successful service flow creation AP will show the flows associated with
given CPE. It shows all active service slows with associated QoS profile index,
classification profile index and the direction (UL or DL).
66
Upon successful service flow creation CPE will show the flows associated its own.
67
11 Appendix A – AAA Server Installation
For Windows:
Download Aradial RADIUS and Prepaid server for evaluation from:
http://www.aradial.com/Ftp
* Open explorer and put it in the URL.
User: ARADIALEVAL
password: ardpower
Note: The cases for the username and password are important.
Or
For Windows: ftp://ARADIALEVAL:ardpower@www.aradial.com/Windows‐v51
‐ Aradial Installation Screen‐cast:
http://www.aradial.com/DownLoads/Demos/Installing_Aradial.wmv
‐ The quick install PDF can be found in each of the download folders.
http://www.aradial.com/DownLoads/Windows‐quick‐installation‐guide.pdf
‐ Please download the temporary registration key 'ARDKEY.reg_' can be found in
each of the download folders. To install it import it with 'regedit' and reboot.
‐ Aradial is installed with MS Access database as default. Aradial supports MySQL,
MS SQL and Oracle.
‐ After the installation the documentation will be under: c:\program
files\Aradial\Docs
‐ Aradial Training: http://www.aradial.com/DownLoads/AradialTraining.zip
For Linux: (CentOS 5.3 Linux)
You can download Aradial RADIUS and Prepaid server for evaluation from:
http://www.aradial.com/Ftp
* Open explorer and put it in the URL.
User: ARADIALEVAL
password: ardpower
Note: The cases for the username and password are important.
Or
For Linux: ftp://ARADIALEVAL:ardpower@www.aradial.com/Linux
‐ Please download the temporary registration key 'ARDKEY.reg_' can be found in
68
each of the download folders.
To install it import it with 'regedit' and reboot.
‐ Aradial Training: http://www.aradial.com/DownLoads/AradialTraining.zip
If using MySQL 5.0.77 you would need to upgrade the mysql‐connector, you can
download it from:
http://www.aradial.com/Ftp/Linux/UnixODBC/CentOS5.3/mysql‐connector‐
odbc‐3.51.27‐0.i386.rpm
2. add the below to /etc/odbc.ini
[aradial]
…
…
Socket = /var/lib/mysql/mysql.sock
Aradial is installed at:
/usr/local/aradial
Start/stop it: service ardrad start | stop | status | restart
Aradialip = your Aradial computer external IP.
http://Aradialip:8000 for Aradial admin ‐ user:admin / pwd: password
All the documentation is at: /usr/local/aradial/Docs
69
12 Appendix B – Troubleshooting
a.
‐
‐
b.
‐
‐
‐
‐
CPE shows DL synchronization – no other messages for CPE status
Check the frequency and channel bandwidth settings on AP and CPE, make
sure they are aligned
Also make sure the distance and direction to the AP is correct. AP T X power
and antenna gain value set appropriately.\
CPE stuck in Authorization – on CPE status
Check the authorization credential on the CPE
Make sure the AP can able to talk with AAA
AAA has the correct provisioning for the CPE
AP has the QoS profiles and Classification profile created which is used by
AAA
70
c.
‐
‐
‐
‐
‐
CPE is flipping between DL sync ‐> Ranging ‐> Operational ‐> DL sync
Check the DHCP configuration is accurate
VSA is created properly at AAA
QoS profiles are created matching with the VSA
Look at the CPE logs under “Management”Æ “Log”, for more information.
If the problem persists, collect the syslog generated by AP.
71
d.
‐
‐
‐
CPE is Operational – but now WAN IP address
Check the DHCP configuration on AP is set correct. DHCP server is reachable
from network where AP’s GMAC is connected to.
Check the DHCP relay and server configuration.
If the problem persists, collect the syslog generated by AP.
72
73

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Author                          : fsa011
Company                         : Motorola
Create Date                     : 2010:02:18 17:38:52-06:00
Modify Date                     : 2010:02:19 03:30:05-08:00
Source Modified                 : D:20100218233807
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : Acrobat PDFMaker 8.1 for Word
Metadata Date                   : 2010:02:19 03:30:05-08:00
Document ID                     : uuid:4776d5ba-8ff9-43d3-8cc2-fa3807026f30
Instance ID                     : uuid:cca5f3fd-1076-4dfe-be87-5000b79c5c81
Subject                         : 10
Format                          : application/pdf
Creator                         : fsa011
Title                           : 
Page Layout                     : OneColumn
Page Count                      : 73
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ABZ89FT7632

Navigation menu