Motorola Solutions 92FT4867 Astro XTL 5000 Digital Mobile Radio User Manual 96C68 B

Download:
Mirror Download [FCC.gov]
Document ID	480093
Application ID	CwiPJZpG4qNrJnAFbridOQ==
Document Description	Resending Ex8 User Man
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	148.07kB (1850833 bits)
Date Submitted	2004-10-19 00:00:00
Date Available	2004-12-11 00:00:00
Creation Date	2004-01-30 11:51:33
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2004-02-19 13:06:48
Document Title	96C68_B.book
Document Creator	FrameMaker 6.0
Document Author:	csd099

ASTRO®
XTL 5000
TM
Digital Mobile Radio
W4, W5, W7, W9 Control Heads
User's Guide
HOME
HORN/
LIGHTS
Mic
Dim
H/L
Home
Emer
Page
BUSY
XMIT
Sel
DIRECT
INDICATOR
Call
Scan
Phon
SELECT
CALL
SCAN
PHONE
PRIORITY/
NON-PRIORITY
INDICATORS
PAGE
or
SECURE
or
EMERGENCY
Pwr
Mon
Volume
Dir
MODE POWER ON/OFF/
KNOB VOLUME KNOB
Mode
DIRECT
MONITOR
Quick Reference Card
ASTRO® XTL™ 5000 Digital
Mobile Radio with W4
Control Head
Mode
PRI blinks
No indicator
2 Press Dir again to return to repeater operation.
1 Press Dir (Direct). The Dir indicator lights.
Transmitting (Conventional Modes)
3 State your FCC call sign at the beginning of each
transmission.
2 When the transmit light comes on solid and no alert
tones sound (or a talk-permit tone or ID sidetone
sounds), speak into the microphone in a normal voice.
2 Press Home or Scan to end scan list selection.
1 Press the Sel button as indicated in the table above
to designate up to two modes as priorities.
Delete from List
Four times
PRI lit
1 Press and hold the microphone PTT button.
First Priority
Three times
NPRI lit
Indicator
Selecting Scan Mode Priority
Second Priority
Non-Priority
Two times
One time
Press Sel
5 Press Home or Scan to exit.
4 Repeat the previous steps to continue editing the list.
Transmitting
Press Home to access the preprogrammed Home
mode.
OR
Turn the Mode knob to select the desired mode
Changing Modes
6 Press Home.
5 Turn Mode knob to select squelch level.
3 Press the Sel button as indicated in the table below to
add or remove the displayed mode from the scan list.
2 Turn the Mode knob to select the mode you want to
program.
3 Press Mon again, or replace the microphone on the
hang-up clip to return to coded-squelch operation.
4 To adjust squelch level, hold Mon until a tone sounds.
1 Hold Scan until a tone sounds and the scan indicator
blinks.
Programming a Scan List
2 On conventional modes with Private-Line or Digital
Private-Line, press Mon or remove the microphone
from the hang-up clip to defeat the coded squelch.
1 Turn the Vol knob clockwise to increase volume or
counterclockwise to decrease volume as desired.
Setting the Volume and Squelch
2 Press Scan again to stop scanning.
1 Press Scan to start a scan. If no activity exists, the
display shows your selected mode. When a scanned
channel or talkgroup becomes active, the display
shows the active mode name. The PRI and NPRI
indicators show priority.
Turning the Radio On and Off
Rotate the Vol (Volume) knob clockwise.
Activating Scan
BASIC OPERATION
The audio is muted and no display
changes take place during the alarm.
Silent
Call (Trunked
Modes only)
A tone sounds and the display
alternates between EMERGNCY and the
zone/channel. When acknowledged,
four more tones sound and the display
shows ACK RCVD, then the radio
returns to normal operation.
Non-Silent
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Press the PTT button and talk.
A tone sounds and the display
alternates between EMERGNCY and the
zone/channel.
Press the PTT button, or press and
hold the emergency button to stop the
emergency condition and unmute the
radio.
Indications/Actions
Alarm Type
Depending on your radio's programming, one of the
emergency sequences described in the table below
occur.
For trunked modes, emergency call (priority access
to a voice channel), silent or non-silent emergency
alarm, or emergency alarm and call is entered.
For conventional modes, a silent or non-silent
emergency alarm data transmission is sent.
Press the emergency actuator (Emer button,
footswitch, hidden pushbutton) to begin an
emergency transmission.
Sending an Emergency Alarm or Call
After ACK RCVD (see Non-Silent Alarm
above) is displayed, the radio has
priority voice-channel access.
Alarm and Call
1 Press Sel or the PTT button. A single tone sounds
and the display changes to PLS WAIT, followed by
telephone-type ringing if the receiving unit is in
service.
Sending a Direct-Entry Enhanced Private
Conversation Call
Press the appropriate Sts # button you wish to send.
The associated indicator blinks until an
acknowledgment is received, then it lights steadily.
Sending a Direct-Entry Keyboard Status
Transmission
3 Press Sel to send the transmission. The display
flashes the selected status/message name until the
dispatcher acknowledges, at which time alert tones
sound and the display shows ACK RCVD. The radio
then returns to normal operation.
2 Rotate Mode to select other statuses.
1 Press Sts. The display shows the last acknowledged
status or first status name.
Sending a Status Transmission
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Press the PTT button and talk.
Indications/Actions
Alarm Type
Initiate an Enhanced Private Conversation call to the
caller.
OR
1 Press the PTT button,
Four tones sound and PAGE RCV flashes on the
display. The tone and display repeat every five
seconds.
Answering a Call Alert Page
To send a Call Alert page following an Enhanced
Private Conversation attempt, follow the instructions
for sending a direct-entry Enhanced Private
Conversation call.
OR
3 Press Sel or the PTT button to send a Call Alert page
to the displayed ID,
2 Follow the instructions for initiating a Private
Conversation to select a unit ID.
1 Press the Page button.
Initiating a Call Alert Page
If the called unit does not respond, press Sel or the
PTT button again to leave a Call Alert page message
and your ID.
A single tone followed by four tones sounds if the
called unit acknowledges the page.
OR
2 If the receiving unit answers, press the PTT button to
identify yourself and proceed with your call.
Radio is in emergency alarm or call
state.
A mode incapable of emergency
transmission has been selected.
Radio is out of range of the
trunking system.
NO EMERG
displayed
OUT RNG displayed
5 Press Sel to select key.
6 Press Home or the PTT button to quit.
6 Press Home or the PTT button to quit.
3 Press Sel to enter the Key Selection Menu.
4 Turn the Mode knob to select desired key.
EMERGNCY
displayed
5 Press Sel to select index.
Telephone dialing pause. Press
Sel to continue the dialing.
P displayed
Unit being called with Enhanced
Private Conversation or Call Alert
Page does not respond, but is
operational.
2 Turn the Mode knob to scroll to KEY SEL.
Display shows a mode in the scan
list with the indicated priority level.
PRI, NPRI
indicators lit
Unit being called with the
Enhanced Private Conversation or
Call Alert Page feature is not in
service, or emergency alarm or
status/message transmission is
not acknowledged by dispatcher.
Radio is in direct (mobile-tomobile) operation.
Dir indicator lit
NO ACK displayed
Indicates you are transmitting.
XMIT light on
Meaning
Displayed conventional mode has
activity on it, or selected trunked
system is currently busy. Wait for
callback.
BUSY light on
Display/Light
DISPLAY AND LIGHT INDICATORS
NO ANSWR
displayed
4 Turn the Mode knob to select desired index.
3 Press Sel to enter the Key Erase Menu.
2 Turn the Mode knob to scroll to ERASE KY.
1 Press and hold the D button until a tone sounds.
Erasing an Encryption Key
6 Press Home or the PTT button to quit.
5 Press Sel to select index.
4 Turn the Mode knob to select desired index.
3 Press Sel to enter the Index Selection Menu.
2 Turn the Mode knob to scroll to INDX SEL.
1 Press and hold the D button until a tone sounds.
Selecting a Key Index
1 Press and hold the D button until a tone sounds.
Selecting an Encryption Key
Press and release the D button. The D indicator lights
up.
Selecting Secure Mode
Press the Home button.
Selecting a Home Zone/Home Mode
2 Turn the Mode knob to select the mode.
1 Press the Zone Up !button or Zone Down "
button to scroll to the desired zone.
Selecting a Zone/Mode (Optional)
You have an
incoming call. Press
Call, then the PTT
button, then talk.
Call Alert page has
been received.
All system radio
channels in use.
Release the PTT
button, and wait for
callback.
Private
Conversation
Call Alert Page
System Busy
4 High-Pitched
Tones every 6
seconds
Phone-Type
Busy Tone
(when pressing
the PTT button)
Dispatcher is
acknowledging your
emergency
transmission. Mobile
unit has received
your Call Alert.
2 High-Pitched
Tones
Dispatcher or
Mobile Unit
Acknowledge
4 High-Pitched
Tones
Central controller
has received request
for Call Alert or
emergency alarm
transmission.
You pressed a valid
key.
The above two
acknowledge tones,
heard in tandem.
Central
Acknowledge
or Valid Key
1 High-Pitched
Tone
Explanation
Feature button
pressed is not valid
in selected mode, or
a Call Alert or
emergency alarm
was not
acknowledged.
5 High-Pitched
Tones
Name
Invalid Key
Alert
Type of Tone
1 Low-Pitched
Tone
ALERT TONES
Failsoft
System central
controller failure. The
radio reverts from
trunked operation to
operation similar to a
conventional
repeater.
Others may share
the channel.
Examples: Not exiting phone mode after a call (radio
cannot receive fleet or subfleet calls), transmitting in
receive-only conventional mode, trying to select a dynamic
mode when no dynamic ID assignment has been made.
High-Pitched
Tone every 10
seconds in
unmuted receive
condition
Out of trunked radio
system range or
system is out of
service.
Present transmission
will soon be disabled.
You have entered a
mode where normal
system traffic will be
missed, or you
attempted something
that is not allowed.
(See examples
below.)
Talk Prohibit/
Out-of-Range
or Time-Out
Timer or Illegal
Mode
Low-Pitched
Tone (upon
pressing the
PTT button
during Transmit)
(Operation
Error)
Explanation
Channel is available
for previously
requested
transmission.
System is accepting
your transmission.
Name
Automatic Call
Back or Talk
Permit
3 Short HighTones (after
requesting a
busy channel)
upon pressing
the PTT button)
Type of Tone
ALERT TONES (Continued)
PWR
DIM
HOME
HOME
VOLUME
Mic
Vol
Mode
POWER
ON/OFF MODE
PAGE
or
SECURE
or
EMERGENCY
Phon
Call
BUSY
XMIT
Sel
DIRECT
INDICATOR
Scan
H/L
Mon
DIRECT
Dir
MONITOR
HORN/
LIGHTS
SCAN
SELECT
PHONE
CALL
PRIORITY/
NON-PRIORITY
INDICATORS
Emer
Page
Quick Reference Card
ASTRO® XTL™ 5000 Digital
Mobile Radios with W5
Control Head
1 Hold Scan until a tone sounds and the scan indicator
blinks.
4 To adjust squelch level, hold Mon until a tone sounds.
3 State your FCC call sign at the beginning of each
transmission.
2 When the transmit light comes on solid and no alert
tones sound (or a talk-permit tone or ID sidetone
sounds), speak into the microphone in a normal voice.
1 Press and hold the microphone PTT button.
Transmittingt
Press HOME to access the preprogrammed Home
mode.
OR
Press the Mode rocker switch to select the desired
mode
Changing Modes
6 Press HOME.
Second Priority
First Priority
Delete from List
One time
Two times
Three times
Four times
No indicator
PRI blinks
PRI lit
NPRI lit
Indicator
2 Press HOME or Scan to end scan list selection.
1 Press the Sel button as indicated in the table above
to designate up to two modes as priorities.
Selecting Scan Mode Priority
Mode
Non-Priority
Press Sel
5 Press HOME or Scan to exit.
4 Repeat the previous steps to continue editing the list.
3 Press the Sel button as indicated in the table below to
add or remove the displayed mode from the scan list.
2 Press the Mode rocker switch to select the mode you
want to program.
Programming a Scan List
3 Press Mon again, or replace the microphone on the
hang-up clip to return to coded-squelch operation.
5 Press the Mode rocker switch to select squelch level.
2 Press Scan again to stop scanning.
1 Press Scan to start a scan. If no activity exists, the
display shows your selected mode. When a scanned
channel or talkgroup becomes active, the display
shows the active mode name. The PRI and NPRI
indicators show priority.
Activating Scan
2 On conventional modes with Private-Line or Digital
Private-Line, press Mon or remove the microphone
from the hang-up clip to defeat the coded squelch.
1 Hold the Vol rocker switch down to increase or
decrease volume as desired, then release.
The display shows volume levels from 0 to 15.
Setting the Volume and Squelch
2 Press Dir again to return to repeater operation.
1 Press Dir (Direct). The Dir indicator lights.
Turning the Radio On and Off
Press the PWR button once.
Transmitting (Conventional Modes)
BASIC OPERATION
The audio is muted and no display
changes take place during the alarm.
Silent
Call (Trunked
Modes only)
A tone sounds and the display flashes
EMERGNCY. When acknowledged, four
more tones sound and the display
shows ACK RCVD, then the radio
returns to normal operation.
Non-Silent
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Press the PTT button and talk.
A tone sounds and the display flashes
EMERGNCY.
Press the PTT button, or press and
hold the emergency button to stop the
emergency condition and unmute the
radio.
Indications/Actions
Alarm Type
Depending on your radio's programming, one of the
emergency sequences described in the table below
occur.
For trunked modes, emergency call (priority access to
a voice channel), silent or non-silent emergency
alarm, or emergency alarm and call is entered.
For conventional modes, a silent or non-silent
emergency alarm data transmission is sent.
Press the emergency actuator (Emer button,
footswitch, hidden pushbutton) to begin an emergency
transmission.
Sending an Emergency Alarm or Call
Alarm and Call
1 Press Sel or the PTT button. A single tone sounds
and the display changes to PLS WAIT, followed by
telephone-type ringing if the receiving unit is in
service.
Sending a Direct-Entry Enhanced Private
Conversation Call
Press the appropriate Sts # button that you wish to
send. The associated indicator blinks until an
acknowledgment is received, then it lights steadily.
Sending a Direct-Entry Keyboard Status
Transmission
3 Press Sel to send the transmission. The display
flashes the selected status name until the dispatcher
acknowledges, at which time alert tones sound and
the display shows ACK RCVD. The radio then returns
to normal operation.
2 Press the Mode rocker switch to select other
statuses.
1 Press Sts. The display shows the last acknowledged
status or the first status name.
Sending a Status Transmission
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Press the PTT button and talk.
Indications/Actions
After the display shows ACK RCVD (see
Non-Silent Alarm above), the radio has
priority voice-channel access.
Alarm Type
Initiate an Enhanced Private Conversation call to the
caller.
OR
1 Press the PTT button,
Four tones sound and PAGE RCV flashes on the
display. The tone and display repeat every five
seconds.
Answering a Call Alert Page
To send a Call Alert page following an Enhanced
Private Conversation attempt, follow the instructions
for sending a direct-entry Enhanced Private
Conversation call.
OR
3 Press Sel or the PTT button to send a Call Alert page
to the displayed ID,
2 Follow the instructions for initiating a Private
Conversation to select a unit ID.
1 Press the Page button.
Initiating a Call Alert Page
If the called unit does not respond, press Sel or the
PTT button again to leave a Call Alert page message
and your ID.
A single tone followed by four tones sounds if the
called unit acknowledges the page.
OR
2 If the receiving unit answers, press the PTT button to
identify yourself and proceed with your call.
Meaning
Radio is out of range of the
trunking system.
OUT RNG displayed
6 Press HOME or the PTT button to quit.
5 Press Sel to select the index.
6 Press HOME or the PTT button to quit.
3 Press Sel to enter the Key Selection Menu.
4 Press the Mode rocker switch to select the desired
key.
2 Press the Mode rocker switch to scroll to KEY SEL.
A mode incapable of emergency
transmission has been selected.
Unit being called with the
Enhanced Private Conversation or
Call Alert Page feature is not in
service, or emergency alarm or
status/message transmission is
not acknowledged by dispatcher.
NO ACK displayed
NO EMERG
displayed
Telephone dialing pause. Press
Sel to continue the dialing.
P displayed
5 Press Sel to select the key.
The display shows the mode in the
scan list with the indicated priority
level.
PRI, NPRI
indicators lit
Radio is in emergency alarm or
call state.
Radio is in direct (mobile-tomobile) operation.
EMERGNCY
displayed
Indicates you are transmitting.
Dir indicator lit
The conventional mode in the
display has activity on it, or
selected trunked system is
currently busy. Wait for callback.
XMIT light on
BUSY light on
Display/Light
DISPLAY AND LIGHT INDICATORS
Unit being called with Enhanced
Private Conversation or Call Alert
Page does not respond, but is
operational.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Key Erase Menu.
2 Press the Mode rocker switch to scroll to ERASE KY.
1 Press and hold the D button until a tone sounds.
Erasing an Encryption Key
6 Press HOME or the PTT button to quit.
5 Press Sel to select the index.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Index Selection Menu.
2 Press the Mode rocker switch to scroll to INDX SEL.
1 Press and hold the D button until a tone sounds.
Selecting a Key Index
NO ANSWR
displayed
1 Press and hold the D button until a tone sounds.
Selecting an Encryption Key
Press and release the D button. The D indicator lights
up.
Selecting Secure Mode
Press the HOME button.
Selecting a Home Zone/Home Mode
2 Press the Mode rocker switch to select the mode.
1 Press the Zone Up ! button or Zone Down "
button to scroll to the desired zone.
Selecting a Zone/Mode (Optional)
You have an
incoming call. Press
Call, then the PTT
button, then talk.
Call Alert page has
been received.
All system radio
channels in use.
Release the PTT
button, and wait for
callback.
Private
Conversation
Call Alert Page
System Busy
4 High-Pitched
Tones every 6
seconds
Phone-Type
Busy Tone
(when pressing
the PTT button)
Dispatcher is
acknowledging your
emergency
transmission. Mobile
unit has received
your Call Alert.
2 High-Pitched
Tones
Dispatcher or
Mobile Unit
Acknowledge
4 High-Pitched
Tones
Central controller
has received request
for Call Alert or
emergency alarm
transmission.
You pressed a valid
key.
The above two
acknowledge tones,
heard in tandem.
Central
Acknowledge
or Valid Key
1 High-Pitched
Tone
Explanation
Feature button
pressed is not valid
in selected mode, or
a Call Alert or
emergency alarm
was not
acknowledged.
5 High-Pitched
Tones
Name
Invalid Key
Alert
Type of Tone
1 Low-Pitched
Tone
ALERT TONES
System central
controller failure. The
radio reverts from
trunked operation to
operation similar to a
conventional
repeater.
Others may share
the channel.
Examples: Not exiting phone mode after a call (radio
cannot receive fleet or subfleet calls), transmitting in
receive-only conventional mode, trying to select a dynamic
mode when no dynamic ID assignment has been made.
High-Pitched
Failsoft
Tone every 10
seconds in
unmuted receive
condition
Out of trunked radio
system range or
system is out of
service.
Present transmission
will soon be disabled.
You have entered a
mode where normal
system traffic will be
missed, or you
attempted something
that is not allowed.
(See examples
below.)
Talk Prohibit/
Out-of-Range
or Time-Out
Timer or Illegal
Mode
Low-Pitched
Tone (upon
pressing the
PTT button
during Transmit)
(Operation
Error)
Explanation
Channel is available
for previously
requested
transmission.
System is accepting
your transmission.
Name
Automatic Call
Back or Talk
Permit
3 Short HighTones (after
requesting a
busy channel)
upon pressing
the PTT button)
Type of Tone
ALERT TONES (Continued)
W4 and W5 Control Heads Foldout Page
W4 Control Head
PAGE
or
SECURE
or
EMERGENCY
Page
Emer
SCAN
PHONE
HOME
HORN/
LIGHTS
Phon
Home
SELECT
MONITOR
CALL
Scan
Call
DIRECT
Dir
Sel
Mode
H/L
Mon
Volume
XMIT
Dim
BUSY
Mic
Pwr
PRIORITY/
NON-PRIORITY
INDICATORS
MODE POWER ON/OFF/
KNOB VOLUME KNOB
DIRECT
INDICATOR
MAEPF-23211-A
W5 Control Head
PAGE
or
SECURE
or
EMERGENCY
POWER
ON/OFF MODE
Page
Emer
SCAN
PHONE
SELECT
CALL
PWR
Phon
Mode
Scan
Call
Sel
Vol
XMIT
DIM
Mic
BUSY
H/L
Mon
Dir
HOME
DIRECT
INDICATOR
HOME
VOLUME
PRIORITY/
NON-PRIORITY
INDICATORS
HORN/
LIGHTS
DIRECT
MONITOR
MAEPF-23212-A
ii
ASTRO® XTL™ 5000
Digital Mobile Radio
with
W4, W5, W7, and W9
Control Heads
User’s Guide
68P81096C68-B
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
iii
Product Safety and RF Exposure Compliance
Before using this product, read the operating instructions for safe
usage contained in the Product Safety and RF Exposure booklet
C a u t i o n enclosed with your radio.
ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy
exposure requirements. Before using this product, read the RF energy
awareness information and operating instructions in the Product Safety and RF
Exposure booklet enclosed with your radio (Motorola Publication part number
68P81095C99) to ensure compliance with RF energy exposure limits.
Computer Software Copyrights
The Motorola products described in this manual may include copyrighted Motorola
computer programs stored in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola certain exclusive rights for
copyrighted computer programs, including, but not limited to, the exclusive right to copy
or reproduce in any form the copyrighted computer program. Accordingly, any
copyrighted Motorola computer programs contained in the Motorola products described
in this manual may not be copied, reproduced, modified, reverse-engineered, or
distributed in any manner without the express written permission of Motorola.
Furthermore, the purchase of Motorola products shall not be deemed to grant either
directly or by implication, estoppel, or otherwise, any license under the copyrights,
patents or patent applications of Motorola, except for the normal non-exclusive license
to use that arises by operation of law in the sale of a product.
Documentation Copyrights
No duplication or distribution of this document or any portion thereof shall take place
without the express written permission of Motorola. No part of this manual may be
reproduced, distributed, or transmitted in any form or by any means, electronic or
mechanical, for any purpose without the express written permission of Motorola.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely
reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola
reserves the right to make changes to any products herein to improve readability,
function, or design. Motorola does not assume any liability arising out of the
applications or use of any product or circuit described herein; nor does it cover any
license under its patent rights, nor the rights of others.
MOTOROLA, the Stylized M Logo, ASTRO, SmartZone, and FLASHport are registered
in the U.S. Patent & Trademark Office. All other product or service names are the
property of their respective owners. P25 radios contain technology patented by Digital
Voice Systems, Inc.
© Motorola, Inc. 2003. All Rights Reserved. Printed in the U.S.A. 4/03.
iv
Notations Used in This Manual
Throughout the text in this publication, you will notice the use of WARNINGS,
CAUTIONS, and Notes. These notations are used to emphasize that safety
hazards exist, and care that must be taken or observed.
WARNING
WARNING: An operational procedure, practice, or other
condition, which might result in injury or death if not carefully
observed.
CAUTION
CAUTION: An operational procedure, practice, or other
condition, which might result in damage to the equipment if not
carefully observed.
Note:
Note: An operational procedure, practice, or other condition,
which is essential to emphasize.
The following special notations identify certain items:
Example
Description
Light button or >
Buttons and keys are shown in bold print or as a key
symbol.
PHONE
Menu items (softkeys) are similar to the way they
appear on the radio’s display.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Notes
vi
Contents
W4 and W5 Control Heads Foldout Page . . . . . . . . . . ii
Computer Software Copyrights ........................................................ iv
Documentation Copyrights ............................................................... iv
Disclaimer ........................................................................................ iv
Notations Used in This Manual ......................................................... v
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Using Your Radio: The Basics .......................................................... 1
Getting Started .................................................................................. 2
Identifying Your Radio ....................................................................... 4
W4 Control Head ........................................................................ 4
W5 Control Head ........................................................................ 4
W7 Control Head ........................................................................ 4
W9 Control Head ........................................................................ 4
Operating Your Control Head ............................................................ 5
Turning On the Radio ........................................................................ 5
Setting the Volume ..................................................................... 6
Adjusting the Display Brightness ................................................ 6
Trunked Modes or Conventional Channels ................................ 7
Field Programming ..................................................................... 7
Display Status ................................................................................... 8
Feature Control ................................................................................. 8
Alert Tones ........................................................................................ 8
Basic Operating Procedures . . . . . . . . . . . . . . . . . . . 11
Basic Functions ............................................................................... 11
Selecting the Zone or Mode ............................................................ 12
Selecting or Changing the Zone ............................................... 12
Selecting or Changing a Mode in the Current Zone ................. 13
Selecting or Changing to a Mode Not in the Current Zone ....... 13
Selecting the Home Mode ............................................................... 14
Transmitting (Conventional Modes Only) ........................................ 15
Transmitting (Trunked Modes Only) ................................................ 15
Selecting the Transmit Power Level ................................................ 16
Monitoring Conventional Mode Activity ........................................... 17
Adjusting the Squelch Level ............................................................ 18
General Radio Features . . . . . . . . . . . . . . . . . . . . . . . 19
Often-Used Features ....................................................................... 19
Emergency Call and Alarm ............................................................. 20
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
vii
Emergency Call .........................................................................20
Initiating an Emergency Alarm ..................................................21
Initiating an Emergency Call .....................................................22
Initiating an Emergency Call and Alarm ....................................23
Initiating a Silent Emergency Alarm ..........................................24
Special Considerations for Emergencies ..................................25
Scan Operation ................................................................................26
Turning On Scan .......................................................................27
Turning Scan On While Disregarding the Squelch Code
(Conventional Modes Only) ...................................................28
Viewing a Scan List ...................................................................29
Transmitting While Scan Is On .................................................30
Temporarily Deleting a Nuisance Mode with Scan On
(W7 and W9 Control Heads Only) .........................................31
Restoring a Nuisance Mode
(W7 and W9 Control Heads Only) .........................................32
Changing Mode Priorities While Scan Is On
(W7 and W9 Control Heads Only) .........................................33
Restoring Mode Priorities in a Scan List
(W7 and W9 Control Heads Only) .........................................33
Programming a Scan List ..........................................................34
Hang Up Box (HUB) ..................................................................36
Optional External Alarms (Horn and Lights) ....................................36
Activating the External Alarm(s) ................................................36
Changing the Selected Alarms .................................................38
Receiving a Call While Alarms Are Turned On .........................39
Time-Out Timer ................................................................................40
Push-To-Talk Identification (PTT-ID) ................................................40
Telephone Interconnect List (Conventional and Trunking) ..............41
Answering a Phone Call ............................................................42
Initiating a Telephone Call from the List ....................................42
Unlimited Telephone Interconnect
(W7 and W9 Control Heads Only) ..................................................44
Calling a Phone Number Not in the List ....................................44
Storing a Number in the List .....................................................46
Editing a Name in the List
(W7 and W9 Control Heads Only) .........................................47
Call Alert Page (Conventional and Trunking— Digital Modes Only) 50
Sending a Call Alert Page .........................................................51
Answering a Call Alert Page .....................................................53
viii
Storing a Unit ID Number in the List
(W7 and W9 Control Heads Only) ......................................... 54
Editing a Name in the List
(W7 and W9 Control Heads Only) ......................................... 55
Conventional Radio Features. . . . . . . . . . . . . . . . . . . 57
Features Used in Conventional Operation ...................................... 57
Status Calls (Digital Modes Only) .................................................... 58
Sending a Status Call (W7 and W9 Control Heads Only) ........ 58
Sending a Direct-Entry Keyboard (DEK) Status
(Digital Modes Only) .............................................................. 60
Smart PTT ....................................................................................... 61
Conventional Talkgroup Calls ......................................................... 62
Digital Modes Only ................................................................... 62
Selecting a Conventional Talkgroup ......................................... 62
Conventional Talkaround ................................................................ 64
Talk Direct (Mobile-To-Mobile) ................................................. 64
Selective Calls (Digital Modes Only) ............................................... 65
Answering a Selective Call ....................................................... 66
Initiating a Selective Call .......................................................... 67
Viewing Your Unit ID Number ................................................... 69
Storing a Unit ID Number in the List
(W7 and W9 Control Heads Only) ......................................... 70
Editing a Name in the List
(W7 and W9 Control Heads Only) ......................................... 71
Trunking Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Features Used on Trunking Systems .............................................. 73
Enhanced Private Conversation (Digital Modes Only) .................... 74
Answering an Enhanced Private Conversation Call ................. 75
Initiating an Enhanced Private Conversation Call .................... 76
Storing a Unit ID Number in the
Private Conversation List
(W7 and W9 Control Heads Only) ......................................... 78
Editing a Name in the
Private Conversation List
(W7 and W9 Control Heads Only) ......................................... 79
Failsoft ............................................................................................. 81
Dynamic Regrouping (Digital Modes Only) ..................................... 82
Receiving a Dynamic Regrouping ID Assignment
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
ix
(W7 and W9 Control Heads Only) .........................................82
Selecting Enable and Disable (Digital Modes Only) ..................83
Requesting a Dynamic Regrouping
(W7 and W9 Control Heads Only) (Digital Modes Only) ........83
SmartZone (W7 and W9 Control Heads Only) ................................85
Site-Button Operation ...............................................................86
Locking onto a Site ...................................................................87
Site Trunking .............................................................................88
Out-of-Range Indication ..................................................................89
Trunked Announcement ..................................................................90
Initiating an Announcement ......................................................91
Secure Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Features Available on Secure XTL 5000 .........................................93
Receiving a Private Message ..........................................................94
Transmitting a Private Message ......................................................94
System Considerations ....................................................................95
Loss Indication .................................................................................96
Selecting an Encryption Key (Conventional Only) ...........................97
Selecting an Encryption Index (Conventional Only) ........................99
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Patent Disclosure ..........................................................................105
Commercial Warranty (Standard) ..................................................105
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
W7 and W9 Control Heads Foldout Page . . . . . . . . 113
Introduction
Using Your Radio: The Basics
This chapter gives you the basic knowledge you need in order to use
your radio. The following topics are covered:
• Getting Started (page 2)
• Identifying Your Radio (page 4)
• Operating Your Control Head (page 5)
• Turning On the Radio (page 5)
• Setting the Volume (page 6)
• Adjusting the Display Brightness (page 6)
• Display Status (page 8)
• Feature Control (page 8)
• Alert Tones (page 8)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Introduction
Getting Started
The ASTRO® XTL™ 5000 Digital Mobile Radio is among the most
sophisticated two-way radios available. It can operate in the following
frequency ranges:
VHF
UHF
700/800 MHz
136-174 MHz
380-470 MHz
762-776 MHz
794-806 MHz
806-825 MHz
851-870 MHz
These channels provide maximum communications capability under
varying operating conditions.
One of the newest in a long line of quality Motorola products, the
ASTRO XTL 5000 Digital Mobile Radio provides improved voice
quality across more of your coverage area. The digital process called
embedded signaling intermixes system signaling information with
digital voice, resulting in improved system reliability and the capability
of supporting a multitude of advanced features. Such features add up
to better, more cost-effective two-way radio communications.
ASTRO digital technology is also helping to provide the solution to
improved spectral efficiency requiring only half as much bandwidth
per channel (12.5kHz) compared to analog technology (25/30kHz).
The net benefit to you is fewer users per channel or more users per
system.
The ASTRO XTL 5000 Digital Mobile radio can include an optional
RS-232 data port to interface with external devices, such as certain
fax machines and laptop computers. ASTRO XTL 5000 Digital Mobile
voice radios and data terminals can access the same channel without
interfering with each other.
Introduction
Note: In this manual—
Analog mode refers to a mode that uses traditional, non-ASTROdigital signaling.
ASTRO mode refers to a mode that uses ASTRO digital signaling.
Your ASTRO XTL 5000 Digital Mobile Radio utilizes Motorola’s
revolutionary FLASHport™ technology. This allows your radio’s
capabilities to be flexible, because FLASHport makes it possible to
add software that drives these capabilities both at the time of
purchase and later on. Similar to how a computer can be loaded with
different software, your radio’s features and capabilities can be
upgraded with software.
FLASHport allows you to add software to your radio as your needs
change and as technology advances, making your radio investment
go further.
FLASHport is the future of radio communications, and it’s yet another
example of Motorola’s commitment to your satisfaction.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Introduction
Identifying Your Radio
The ASTRO XTL 5000 Digital Mobile Radio’s capabilities, and the
operation of its features, differ depending on which control head is
ordered. Keep the foldout pages open for reference as you read this
manual. Your radio has one of the following control heads:
W4 Control Head
The W4 has rotary Mode and Volume knobs and a limited set of
control buttons, eight-digit display, and no 12-button keypad (page ii).
W5 Control Head
The W5 features a limited set of control buttons, eight-digit display,
and no 12-button keypad (page ii).
W7 Control Head
The W7 has the same keys and display as the W5 control head, plus
a 12-button keypad (page 113).
W9 Control Head
The W9 has the identical keys and keypad as the W7 control head,
but features an 11-digit display (page 113).
Introduction
Operating Your Control Head
Your advanced control head is designed for ease of use and flexibility
of feature control. Before operating the radio, familiarize yourself with
the various controls, indicators, and alert tones. Refer to the foldout
diagrams in the front and back of this manual for your particular
control head.
Turning On the Radio
Basic operation is the same for all radio control heads. Control heads
with additional features are noted.
Do one of the following:
•
W4 Control Heads: Rotate the Volume knob clockwise.
•
W5 and W7 Control Heads: Press the power button in the
upper left corner of the control unit.
•
W9 Control Heads: Slide the power switch on the bottom of
the control unit to the left.
The display and graphics illuminate, indicating that the radio is
on.
When the ASTRO XTL 5000 Digital Mobile Radio is turned on,
the display shows XTL 5000.
The radio then performs a self check.
Note: If FL##/## (W4,W5,W7) or FAIL ##/## (W9) appears in the
display, the radio will not function until the condition has
been corrected.
If ER##/## (W4,W5,W7) or ERROR ##/## (W9) appears,
some non-critical data has been changed. If either of these
displays appear, if the display goes blank, or if the unit
appears to be locked up, refer to the “Troubleshooting”
section.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Introduction
Setting the Volume
Choose one of the following:
•
W4 Control Head: Rotate the Volume knob clockwise to
increase the volume and counterclockwise to decrease the
volume.
W5, W7, and W9 Control Heads: Press and hold the Vol
rocker switch.
A volume indication
(0-15) appears on the display. For example,
VOL 10 (W5, W7) or VOLUME 10 (W9).
Hold the button until the sound level increases (or
decreases) to the desired level.
Adjusting the Display Brightness
Press the dimmer button (Dim on W4, or DIM on W5, W7, and
W9) to change the display brightness to one of four levels:
•
Off to high
•
High to medium
•
Medium to low
•
Low to off.
In Off, both the display and backlight are off (used for
surveillance operations).
Introduction
Trunked Modes or Conventional Channels
Depending on how your radio is programmed, you can select
conventional channels or trunked talkgroup. Conventional channels
consist of a transmit and receive frequency pair, an associated
squelch code pair, and a time-out timer value. See “Conventional
Radio Features” on page 57.
Trunked modes consist of the system/announcement group/talkgroup
combination and a time-out timer value. See “Trunking Operation” on
page 73.
Field Programming
Other radio features may be slaved to the selected mode by field
programming. This mode slaving means that the radio is
preprogrammed to automatically give you the proper operation for
each mode you select.
You may use the control head to program your own mode names.
The names you assign are clearly shown in the alphanumeric display.
You can see all the key operating information, including the mode
selected or being scanned, and the on/off status of various features.
The operating conditions are shown either by the display or by visual/
audio indicators, or by both.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Introduction
Display Status
The control head display indicates your selected mode, or the
currently active receive mode when scan is on.
Feature Control
You can turn the various radio features on or off, change modes, and
adjust the volume.
To exit a feature, such as phone, press the HOME button or the
feature button (for example, Phon).
Alert Tones
Tone Type
Name
Two highpitched tones
Private
Conversation™
Indicate that a private call has been
received.
Four highpitched tones
every six
seconds
Call Alert
Indicate that a Call Alert page has been
received.
Single, highpitched tone
Central
Acknowledge
Indicates that a Call Alert, emergency
alarm, reprogram request, or status/
message transmission has been
received by the system’s central
controller.
Four highpitched tones
Mobile Unit
Acknowledge
Indicate that a Call Alert page has been
received by the intended unit, or the
emergency alarm, reprogram request, or
status/message transmission has been
acknowledged by the intended
dispatcher.
Description
Introduction
Tone Type
Name
Description
Sound similar
to a telephone
busy signal
System Busy
Indicates, when you press the
microphone push-to-talk (PTT) button,
that you cannot transmit because all
system radio channels are in use.
Release the PTT button and wait for call
back.
A series of
three short,
high-pitched
tones
Automatic Call
Back
Indicate that a channel is now available
for your previously requested
transmission.
A series of
three short,
high-pitched
tones (same
as automatic
call back)
Talk Permit
(optional)
Indicate, when you press the
microphone PTT button, that the system
is accepting your transmission.
Continuous,
low-pitched
tone
Talk-Prohibit/
Out-of-Range
Indicates, when you press the
microphone PTT button, that either you
are out of the range of the trunked radio
system, or the system is out of service,
or the channel is busy with the Smart
PTT feature enabled.
Single, highpitched tone
every ten
seconds
Failsoft
In an unmuted receive condition,
indicates a trunked system central
controller failure. The radio reverts from
trunked operation to a system similar to
conventional radio repeater operation.
Other system users can be heard
sharing the channel.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Introduction
Tone Type
Name
Description
Continuous,
low-pitched
tone
Illegal Mode
Indicates that you have entered a mode
where normal system traffic will be
missed, or you are attempting something
which is not permitted. Examples
include: forgetting to exit the telephone
interconnect mode after a call ends (fleet
and subfleet calls cannot be received),
attempting to transmit on a receive-only
conventional mode, attempting to select
a dynamic mode where no dynamic ID
assignment has been made.
Brief tone
Volume-Set
Tone
Indicate the volume level when you
press the Vol rocker switch on a quiet
channel (W5, W7, and W9 control heads
only).
Brief lowpitched tone
Time-Out Timer
Warning
Indicates that your present transmission
will soon be disabled.
Single, short,
high-pitched
tone
Valid Key
Indicates that you pressed a valid key, or
you entered a feature configuration
state, or you are receiving or
transmitting in the clear mode on secure
models (with TX Clear Alert Tones
enabled).
Single, lowpitched tone
Invalid Key
Indicates that you tried to make an
invalid key press, or that an emergency
alarm, reprogram request, or status/
message was not acknowledged.
Unique
chirping
sound
Dynamic
Reprogramming
Indicates that a dynamic ID is assigned.
10
Basic Operating Procedures
Basic Functions
This chapter shows you how to access the radio’s basic functions and
includes the following topics:
•
Selecting the Zone or Mode (page 12)
•
Selecting the Home Mode (page 14)
•
Transmitting (Conventional Modes Only) (page 15)
•
Transmitting (Trunked Modes Only) (page 15)
•
Selecting the Transmit Power Level (page 16)
•
Monitoring Conventional Mode Activity (page 17)
•
Adjusting the Squelch Level (page 18)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
11
Basic Operating Procedures
Selecting the Zone or Mode
A zone is a grouping of modes. A mode is a group of characteristics
such as transmit/receive frequencies, Private-Line™ codes, radio
parameters, and an alphanumeric name.
Selecting or Changing the Zone
Press the ! (Zone up) button or " (Zone down) button.
12
Basic Operating Procedures
Selecting or Changing a Mode in the Current Zone
To access a mode in the current zone, do one of the following:
•
W4 Control Head: Turn the Mode knob until the display
shows the desired mode name.
•
W5 Control Head: Press the Mode rocker switch until the
display shows the desired mode name.
•
W7 and W9 Control Heads:
Press and hold
HOME .The zone/mode flashes.
Release
Enter the number by the keypad, and press
HOME .
HOME
again.
Selecting or Changing to a Mode Not in the Current
Zone
To access a mode that is not in the current zone, press the
Zone up ! button or Zone down " button to move to the
zone containing the mode.
Note: The Zone up ! and Zone down " buttons are optional
buttons included with the radio when zone/mode is ordered.
Do one of the following:
•
W4 Control Head: Turn the Mode knob to select the desired
mode.
•
W5, W7, and W9 Control Heads: Press the Mode rocker
switch to select the desired mode.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
13
Basic Operating Procedures
Selecting the Home Mode
This feature must first be enabled by a qualified radio
technician.
Press
Home (W4, W9) or HOME (W5, W7) to select the
home mode contained within the home zone, from any other
zone and mode in the radio.
14
Basic Operating Procedures
Transmitting (Conventional Modes Only)
Lift the microphone off-hook, and listen for activity on that mode.
If you hear no activity, press and hold the microphone PTT
button.
Transmitting (Trunked Modes Only)
Lift the microphone off-hook, and press the microphone PTT
button.
Do one of the following:
•
If you hear three quick tones, or if you hear no tone and the
red XMIT (transmit) indicator lights steadily, proceed with
your message.
Release the PTT button to receive.
OR
•
If you hear a continuous low-pitched tone, you are out of the
system's range.
The red XMIT indicator may flash several times as the radio
tries to access the system.
Release the PTT button and try again when the vehicle is
driven within range of the system.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
15
Basic Operating Procedures
Selecting the Transmit Power Level
The L PWR button lets you select (toggle) the transmit power level.
Press L PWR .
The display momentarily shows LOW PWR or HIGH PWR (W4, W5,
W7), or LOW POWER or HIGH POWER (W9) to indicate the transmit
power level selected.
Also, when low-power transmission is selected, the L PWR
indicator lights.
16
Basic Operating Procedures
Monitoring Conventional Mode Activity
This feature allows you to monitor channel traffic on conventional
channels by defeating the coded squelch. This feature must first be
enabled by a qualified radio technician or system administrator.
Do one of the following:
•
Take the microphone off hook (This is the same as monitor
on. You hear all channel traffic.),
OR
•
W4, W5, and W7 Control Heads: Pressing
Mon
momentarily toggles between MON ON and MON OFF.
MON ON shown on the display indicates that the radio is
monitoring.
Pressing
Mon again turns monitor off and you don’t
hear all channel traffic.
•
W9 Control Head: Press
Sql
momentarily.
MONITOR ON shown on the display indicates that the radio is
monitoring.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
17
Basic Operating Procedures
Adjusting the Squelch Level
Choose one of the following:
•
W4, W5, and W7 Control Heads: Press and hold Mon
The display shows SQL XX; where XX is a squelch level
setting of 0 to 15.
•
W9 Control Head: Press and hold
Sql
momentarily.
The dis[play shows SQUELCH XX, where XX is a squelch level
setting of 0 to 15.
Adjust the squelch level by turning the Mode knob (W4) or by
pressing the Mode rocker switch (W5, W7, W9) to reach the
desired squelch level setting.
Press
Home
(W4, W9) or
the selected channel.
18
HOME
(W5, W7) to return to
General Radio Features
Often-Used Features
This chapter shows you how to access the most frequently used
features. The following topics are covered:
•
Emergency Call and Alarm (page 20)
•
Scan Operation (page 26)
•
Optional External Alarms (Horn and Lights) (page 36)
•
Time-Out Timer (page 40)
•
Push-To-Talk Identification (PTT-ID) (page 40)
•
Telephone Interconnect List (Conventional and Trunking)
(page 41)
•
Call Alert Page (Conventional and Trunking—Digital Modes
Only) (page 50)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
19
General Radio Features
Emergency Call and Alarm
The emergency call and alarm features allow you to have priority
channel access and/or send an emergency data transmission to the
dispatcher in an emergency situation.
The desired type of emergency feature—alarm, call, call and alarm,
or silent alarm—can be preprogrammed by a qualified radio
technician.
The radio must be turned on to activate any emergency feature.
Emergency Call
Emergency call gives you priority access to a voice channel for all
subsequent transmissions after you press the emergency button. The
level of priority access is determined by the system manager.
SmartZone Emergency Call Receive Operation
A radio configured for SmartZone® operation displays EMER
RECEIVED whenever it receives an emergency call. The display
alternates with the selected-mode display as long as the radio is
unmuted to the emergency call.
20
General Radio Features
Initiating an Emergency Alarm
The emergency alarm feature sends a data transmission to alert the
dispatcher of your emergency condition and identify your unit ID.
Press the emergency button.
A tone sounds and the display alternates EMERGNCY (W4, W5,
W7) or EMERGENCY (W9) with the current zone/channel.
For trunking modes, a high-pitched tone indicates that the
alarm has been received by the trunked system’s central
controller.
A dispatcher acknowledgment (four high-pitched tones) and an
ACK RCVD display follow.
The radio automatically returns to normal operation. No further
action is required.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
21
General Radio Features
Initiating an Emergency Call
Press the emergency button.
A tone sounds and the display alternates EMERGNCY (W4, W5,
W7) or EMERGENCY (W9) with the current zone/channel.
Press the PTT button and announce your emergency.
After completing the emergency call, press and hold the
emergency button until a tone sounds.
The alternating EMERGNCY (W4, W5, W7) or EMERGENCY (W9)
display disappears, and the radio returns to normal operation.
22
General Radio Features
Initiating an Emergency Call and Alarm
If the radio has both emergency call and alarm features, it
automatically proceeds to the call mode after the alarm is
acknowledged.
Press the emergency button to activate the emergency call/
alarm feature.
The display begins alternating EMERGNCY (W4, W5, W7) or
EMERGENCY (W9) with the current zone/channel.
For trunking modes, a high-pitched tone sounds, indicating
that the alarm has been received by the trunked system’s
central controller.
A dispatcher acknowledgment (four high-pitched tones) follows,
accompanied by an ACK RCVD display.
Press the PTT button and announce your emergency.
To exit from the emergency state altogether, press and hold the
emergency button until a tone sounds.
The alternating EMERGNCY (W4, W5, W7) or EMERGENCY (W9)
display disappears, and the radio returns to normal operation.
Note: Turning the radio off also cancels the emergency state.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
23
General Radio Features
Initiating a Silent Emergency Alarm
Press the emergency button to activate the silent alarm feature.
During a silent emergency alarm, there are no display changes,
and the receiver audio mutes so that no indication is given that
an emergency alarm has been sent.
To exit the silent alarm mode, press and hold the emergency
button until a tone sounds.
Note: If silent emergency alarm is used with emergency call,
pressing the PTT button exits the silent mode and initiates
the emergency call.
24
General Radio Features
Special Considerations for Emergencies
•
If you press the emergency button while in a mode that has no
emergency capability, a low-pitched tone sounds.
•
If the unit is out of the range of the system and/or the emergency
alarm is not acknowledged, a tone sounds and the display shows
NO ACK.
•
If you press the emergency button, then change to a mode that
has no emergency capability, a NO EMERG (W4, W5, W7) or NO
EMERGNCY (W9) display alternates with the mode name display,
and a continuous low-pitched tone sounds until a valid emergency
mode is selected or until the emergency is cancelled.
•
When an emergency is active, changing to another mode where
emergency is enabled (trunked or conventional) causes an
emergency alarm and/or emergency call to be active on the new
mode.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
25
General Radio Features
Scan Operation
The scan feature allows you to monitor activity on different
conventional or trunked modes by scanning a scan list of modes. The
modes to be scanned in a scan list are programmed by a qualified
radio technician. You can select the modes to be scanned in a scan
list if operator-selectable scan is enabled.
There are three types of scan lists available:
•
Conventional—Comprises up to 15 different conventional-only
modes
•
Trunked Priority Monitor—Comprises up to 15 modes that are all
from the same trunked system
•
Talkgroup Scan—Comprises up to 10 combined conventional
modes and modes from one trunking system
The radio supports both priority and non-priority scanning. With
priority scanning enabled, a scan list can have one mode assigned as
the first-priority mode and a second as the second-priority mode.
The XTL 5000 Digital Mobile Radio supports automatic scanning
(autoscan), which can be programmed into the radio by a qualified
radio technician. With this feature, the radio begins scanning
whenever you select a mode to which a scan list is assigned.
Note: You cannot turn scan off on a mode that has autoscan
enabled.
If multiple scan types are enabled in the radio, the type of scan that is
activated depends on the personality of the mode selected when
Scan
is pressed. For all types of scan, the selected mode is, by
default, a member of its own scan list.
Scan lists stay in memory when you turn scan off, turn the radio off, or
disconnect the radio from the battery.
26
General Radio Features
Turning On Scan
Press
Scan
scanning.
momentarily on a non-autoscan mode to start
The Scan indicator lights and a list of modes is scanned for
activity.
When a scanned mode becomes active, the display changes to
show the active mode name, the appropriate priority indicator
lights, and the radio unmutes.
The radio will not begin scanning again for a predetermined
hang time after the call ends, giving you time to respond. The
hang time is typically three seconds (by default), but can be
changed by a qualified radio technician.
Note: A lit N PRI (non-priority) indicator means that the active
mode is a non-priority member of the scan list (for all scan
types).
A solidly-lit PRI (priority) indicator means that the active
mode is the priority 2 member of the scan list (Trunking
Priority Monitor and Conventional scan types only).
A blinking PRI indicator means that the active mode is the
priority 1 member of the scan list (Trunking Priority Monitor
and Conventional scan types only).
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
27
General Radio Features
Turning Scan On While Disregarding the Squelch
Code
(Conventional Modes Only)
Choose one of the following:
•
W4, W5, and W7 Control Heads: Press
Mon
momentarily. The brief MON ON display indicates that the
radio is disregarding the squelch code.
•
W9 Control Heads: Press
momentarily. The brief
Sql
MONITOR ON display indicates that the radio is disregarding
the squelch code.
Note: While scanning for activity, you can still receive fleetwide,
system-wide, dynamic regrouping, incoming telephone
interconnect and Private Conversation/Call Alert calls.
Respond to these types of calls as you would normally on
the selected mode. However, when scanning different
modes while in talkgroup scan, incoming Private
Conversation/Call Alert calls may be missed.
28
General Radio Features
Viewing a Scan List
Press and hold
Scan
until the Scan indicator blinks and a
beep is heard.
The radio suspends scanning while a scan list is being
reviewed.
Choose one of the following:
•
W4 and W5 Control Heads: Turn the Mode knob or press
the Mode rocker switch to scroll up or down through the
programmed modes. Those modes that are in the scan list
are indicated by a N PRI, PRI or blinking PRI indicator
(indicating the mode’s assigned priority).
•
W7 and W9 Control Heads: Press the Mode rocker switch
to scroll up or down through the programmed modes. Those
modes that are in the scan list are indicated by a N PRI, PRI
or blinking PRI indicator (indicating the mode’s assigned
priority as previously described). Press
Rcl
only the modes that are already in the scan list.
Press
HOME
or
Scan
to review
Scan momentarily to exit the
scan list and resume scanning.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
29
General Radio Features
Transmitting While Scan Is On
Radio Programmed for Talkback Scan
Press the microphone PTT button to transmit on the mode
indicated by the display.
The radio does not begin scanning again for a predetermined
hang time (programmable by a qualified radio technician) after
you release the PTT button, allowing the other party to respond.
If the other party responds within the hang time, scanning does
not resume until the full hang time expires after they have
finished speaking, allowing the conversation to be completed.
Note: To transmit on the selected channel if another channel is
active, first turn scan off by pressing
Scan
momentarily.
Radio Programmed for Non-Talkback Scan
In selected mode or fixed mode, press the microphone PTT
button at any time to transmit on the selected mode or fixed
mode.
Note: To make a Call Alert page, or Private Conversation call while
scanning, press
Page or
Call . The call is entered
on the selected mode and scanning is halted until the call is
exited by pressing
30
HOME
or
Page
, or
Call
General Radio Features
Temporarily Deleting a Nuisance Mode with Scan On
(W7 and W9 Control Heads Only)
To temporarily delete a mode that you do not wish to hear
(nuisance mode), press
Del
active (indicated by the display).
once while the mode is
You can delete undesired modes.
Note: Priority modes, the selected mode, and the designated
transmit mode cannot be deleted.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
31
General Radio Features
Restoring a Nuisance Mode
(W7 and W9 Control Heads Only)
To restore the original scan list, do one of the following:
•
Press
•
Turn scan off, then on.
•
Change modes.
•
Turn off the radio, and then turn it back on.
Rcl
Note: Nuisance mode delete can be disabled by the system
administrator.
32
General Radio Features
Changing Mode Priorities While Scan Is On
(W7 and W9 Control Heads Only)
When active, this dynamic priority feature allows you to change the
priority of a non-priority mode in the scan list to priority 2.
To change the priority of a non-priority channel in the scan list to
priority 2, press
Sel
You cannot alter the status of the priority 1 member.
Restoring Mode Priorities in a Scan List
(W7 and W9 Control Heads Only)
To restore the original mode priorities in a scan list, do one of
the following:
•
Press
•
Turn scan off, then on.
•
Change modes.
•
Turn off the radio, and then turn it back on.
Rcl
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
33
General Radio Features
Programming a Scan List
To program a scan list, operator-selectable scan list members first
must be enabled in the radio programming by a qualified radio
technician.
Adding a Channel to the Scan List
Press and hold
until the scan indicator blinks and a
Scan
good-key chirp is heard.
Using the Mode knob (W4) or Mode rocker switch (W5, W7,
W9), locate the channel to be added.
Note: If the desired channel resides in a different zone, press the
Zone up ! or Zone " down button to change zones, then
use the mode changer to find the desired channel.
Press
Scroll through of the available priority choices, and press
Sel
Sel
to add the channel.
to choose one.
The new channel becomes a member of the scan list assigned
to the selected channel when scan list programming was
entered.
Note: If a scan list is full, you will hear a bad-key chirp each time
you press
, and the desired channel will not be
Sel
assigned to the list.
Press either
Scan
or
HOME
to exit scan list
programming and return to normal scan operation.
34
General Radio Features
Deleting a Channel from the Scan List
Press and hold
Scan
until the scan indicator blinks and a
good-key chirp is heard.
Using the Mode knob (W4) or the Mode rocker switch (W5, W7,
W9), locate the channel to be deleted.
Note: If the desired channel resides in a different zone, press the
Zone up ! or Zone " down button to change zones, then
use the mode changer to find the desired channel.
Press
Sel
to scroll through the available priority choices
until the priority choice disappears.
This indicates that the channel is no longer a member of the
scan list that was assigned to the selected channel.
OR
Press
Rcl
members.
momentarily to scroll through just the scan list
(Optionally for W7 and W9 Control Heads) Delete a channel
from a scan list by pressing
Del
Note: If you delete all members of a scan list, and scan is
subsequently turned on, you will hear a continuous lowpitched tone, and the display will change to NO LIST (W4,
W5, W7) or EMPTY LIST (W9).
You cannot delete the designated transmit mode, the
selected mode, or the fixed scan list members. The selected
mode, by default, is always scanned when scan is turned
on, regardless of whether or not it is explicitly programmed
as a scan list member.
Press
Scan
or HOME
to exit scan list programming and
return to normal scan operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
35
General Radio Features
Hang Up Box (HUB)
To temporarily suspend Scan Mode operation, remove the
microphone from the Hang Up Box (HUB). You are allowed to use the
microphone while scan is suspended. Priority Member scanning is
not suspended, however. This feature applies to all Scan Lists and
Scan Types. Scan is resumed once the microphone is returned to the
holding clip and the preprogrammed hang time has elapsed.
Note: Priority Scan List members are continuously scanned only
when the Scan List, Designated Tx Member field is set to
“Talkback” in the radio programming. Otherwise, all scan
mode operation is suspended.
Optional External Alarms (Horn and Lights)
All control heads can be equipped for external alarms (horn and
lights) that are activated when a Call Alert page, Private Conversation
call, or phone call is received.
These features are useful when you must leave the vehicle, but need
to receive any incoming messages.
The radio always powers up with the horn and lights feature enabled.
Activating the External Alarm(s)
Non-Permanent Horn and Lights
Press
H/L
momentarily.
The last selected alarm(s) are enabled, and the display
alternately shows the enabled alarm(s), then the selected
mode.
36
Press
H/L
a second time to turn off the alarm(s).
General Radio Features
Permanent Horn and Lights
Press
H/L
momentarily.
The last selected alarm(s) are enabled.
The display briefly shows the enabled alarms, and then reverts
back to the selected mode.
Press
H/L
a second time to turn off the alarm(s).
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
37
General Radio Features
Changing the Selected Alarms
Press and hold
H/L
until a tone sounds and the display
indicates the currently selected alarm.
Turn the Mode knob (W4) or press the Mode rocker switch
(W5, W7, W9) to review the choices until the display shows the
desired alarm:
•
HORN ON
•
LITES ON (W4, W5, W7) or LIGHTS ON (W9)
•
H/L ON (both horn and lights)
Press
HOME
or
H/L
return to normal operation.
38
to select the desired alarm and
General Radio Features
Receiving a Call While Alarms Are Turned On
When a call is received, the vehicle’s horn sounds for four seconds,
and/or the car lights turn on for 60 seconds. The time interval can be
modified by a qualified radio technician.
The display alternates between the type of call received (CALL,
PAGE, or PHONE) and the selected mode name.
Turning Off Non-Rearmable External Alarm
To turn off the external alarm(s), press the PTT button or any
control-head button.
Note: Pressing
Call , Page , or Phon will turn off the
external alarm(s) and place you directly in that feature.
The Vol rocker switch (or knob) and the Dim button have no
effect on the state of the external alarm(s).
To rearm the horn and lights feature, press
H/L
momentarily.
Turning Off Rearmable External Alarms
To turn off the external alarm(s), press the PTT button or any
control head button other than the H/L button.
Pressing
Call , Page , or Phon turns off the
external alarm(s) and places you directly in that feature. When
the external alarm(s) are turned off, they will be automatically
rearmed.
Note: Pressing
turns off the external alarm(s) and exits
H/L
the horn and lights feature. To re-arm the feature, press
H/L
momentarily.
The Vol rocker switch (or knob) and the Dim button have no
effect on the state of the external alarms.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
39
General Radio Features
Time-Out Timer
All ASTRO XTL 5000 Digital Mobile Radios provide a time-out timer
function that prevents locking up a repeater or channel by prolonged
keying of the transmitter. You cannot transmit longer than the preset
timer setting. If you attempt to do so, the radio automatically stops
your transmission, and you hear a talk-prohibit tone.
Note: You will hear a brief, low-pitched, warning tone four seconds
before the transmission times out.
The timer is set for 60 seconds at the factory, but it can be
reprogrammed by a qualified radio technician for between 15 and 465
seconds (7.75 minutes), in 15-second intervals, or it can be disabled
entirely for each radio mode.
Push-To-Talk Identification (PTT-ID)
When you press the PTT button to send a message, your radio ID
number is transmitted as part of each voice message. This PTT-ID
number is then shown on the receiving radio’s display.
For the digital mode, the display shows up to eight right-justified
digits.
Pressing
Call
erases the PTT-ID from the display.
The display conditions of PTT-ID must be programmed by a qualified
radio technician.
40
General Radio Features
Telephone Interconnect List (Conventional
and Trunking)
With any of the control heads, you can initiate and receive telephone
calls if the system is properly equipped. All calls between the mobile
operator and the land line are private, regardless of who initiates the
call.
All control heads feature a phone list capability of up to 100
preprogrammed phone numbers. The radios can be programmed by
a qualified radio technician so that a name can be assigned to each
number in the list.
In addition to the 100 preprogrammed phone numbers, the W7 and
W9 Control Heads feature unlimited dialing capability with their 12button telephone keypad.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
41
General Radio Features
Answering a Phone Call
When a phone call is received, telephone-type ringing sounds
and the display shows PHONE CALL (W9) or PHN CALL (W4,
W5, W7).
Press
Press the PTT button to talk; release it to listen.
When the call is completed, press
Phon
HOME
or
Phon
to
hang up and return to normal operation.
Initiating a Telephone Call from the List
Press
Phon
momentarily to select the phone function.
(All Control Heads) A valid-key chirp is heard.
(W4, W5, and W7 Control Heads Only) The phone indicator
lights.
The display shows the last number dialed or a blank scratchpad
appearing as a series of dashes.
Turn the Mode knob (W4), or press the Mode rocker switch
(W5, W7, W9) to locate the number you want to call.
The display first shows the name, and then the number.
Press
Sel
or the PTT button.
The display shows the number that is automatically dialed.
42
General Radio Features
Note: If the number contains a programmed pause, the dialing
pauses briefly when the display shows P. After the brief
pause, the rest of the numbers are dialed.
If you are out of range of the trunked system, the display
shows NO PHONE, and a continuous low-pitched tone
sounds. Press
HOME
or
Phon
to resume normal
operation.
If the trunked phone interconnect is in use or the phone
interconnect is out of service, a telephone-type busy tone
sounds, and the display shows PHON BSY (W4, W5, W7) or
PHONE BUSY (W9). Your number is automatically dialed
when the phone interconnect becomes available. If you
hang up, you lose your place in the queue.
If the display shows PHON BSY (W4, W5, W7) or PHONE
BUSY (W9) with a low-pitched tone rather than a telephonetype busy tone, the call is not queued. You must hang up
and try again.
When your party answers, press the PTT button to talk, and
release it to listen.
When the call is completed, press
HOME
or
Phon
to
hang up and return to normal operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
43
General Radio Features
Unlimited Telephone Interconnect
(W7 and W9 Control Heads Only)
Calling a Phone Number Not in the List
Press
Phon
momentarily to select the phone function.
The Phone indicator lights (W7 only), and the display shows the
last number dialed (W7 and W9).
Enter the desired phone number from the keypad.
The display updates as the numbers are entered.
Note: To include a pause in the dialing sequence, press the *
button followed by the # button. A P appears in the display.
To backspace, press the Mode down rocker switch once, or
# Del
Press
Sel
twice.
or the microphone PTT button to automatically
dial the number in the display.
Note: If the number contains a programmed pause, the dialing
pauses briefly when the display shows P. After the brief
pause, the rest of the numbers are dialed.
44
When your party answers, press the PTT button to talk, and
release it to listen.
General Radio Features
Note: If you are out of range of the trunked system, the display
shows NO PHONE, and a continuous low-pitched tone
sounds. Press
HOME
or
Phon
to resume normal
operation.
If the trunked phone interconnect is in use or the phone
interconnect is out of service, a telephone-type busy tone
sounds, and the display shows PHON BSY (W7) or PHONE
BUSY (W9). Your number is automatically dialed when the
phone interconnect becomes available. If you hang up, you
lose your place in the queue.
If the display shows PHON BSY (W7) or PHONE BUSY (W9)
with a low-pitched tone, rather than a telephone-type busy
tone, the call is not queued. You must hang up and try again.
If your radio is programmed for live overdial, every digit
pressed after the phone call is established is sent to the
telephone system.
If your radio is programmed for buffered overdial, the digits
pressed are entered into the radio’s memory, and they are all
sent together when the PTT button is next pressed. You
cannot send digits and talk on the same PTT button press. If
you press the PTT button to send the digits, you must
release the PTT button and press it again to transmit.
When the call is completed, press
HOME
or
Phon
to
hang up and return to normal operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
45
General Radio Features
Storing a Number in the List
Press and hold
Phon
to select the phone programming
function.
The phone indicator flashes (W7 only).
Do one of the following:
•
Press the Mode rocker switch to locate the number you want
to change.
OR
•
Use the keypad to move directly to the phone number you
want to change.
Press
Enter the new phone number on the keypad.
Sel
to edit the number in the display.
Note: To backspace, press the # button twice or the Mode down
" button once. Enter a pause by pressing the * button,
then the # button.
Press
Do one of the following:
•
Press
Sel
to store the new number.
HOME
to return to normal radio operation.
Phon
to return to normal phone operation.
OR
•
46
Press
General Radio Features
Editing a Name in the List
(W7 and W9 Control Heads Only)
Press and hold
Phon
to enter Phon ID list programming.
The Phon indicator flashes and a high-pitched tone sounds.
Press the Mode rocker switch to locate the list member you
want to change.
OR
Use the numbered keys to go immediately to the location of a
member in the list. For example, press 2 to go to the second
member in the list; press 1 and 0 to go to the tenth member in
the list, and so on.
Change the characters or numbers using any of the numeric
keys (0 through 9) and special function keys
(*, #).
Note: The maximum number of characters permitted in a text line
is 8 for W7 Control Head and 11 for W9 Control Head. If you
try to add too many characters, you will hear a low-pitched
tone.
To edit, do any or all of the following:
•
To enter a character at the blinking cursor, refer to the table
on page 49.
Press the key of the desired character the number of times
shown in the table. For example, to enter the character C,
press the 2 key three times.
•
To leave a space in the text, press the Mode up ! rocker
switch to move the blinking cursor to the next character
position, and then enter the character.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
47
General Radio Features
•
To delete characters, press the Mode down " rocker switch
to move backwards over existing characters.
When the last character on the display has been erased,
press the Mode down " rocker switch again to leave the
name-edit mode, without making any changes, and begin
the procedure again at step 2.
To save the changes, press and hold
Sel
Note: Press
momentarily to confirm changes to a
Sel
number in the list.
Repeat steps 2 through 4 until you have modified all the desired
names,
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
Phon
to return to normal phone operation.
OR
•
48
Press
General Radio Features
Table 1: Entering Characters Using the Keypad
Number of times the key is pressed
Key
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
49
General Radio Features
Call Alert Page (Conventional and Trunking—
Digital Modes Only)
The Call Alert feature allows a radio to selectively alert another radio,
and to determine whether or not that radio received the alert. A Call
Alert page can be initiated after an unsuccessful Private Conversation
call or as a separate feature.
All Control Heads are capable of responding to a Call Alert initiated by
another radio. The following further describes each Control Head’s
capability:
•
All Control Heads: Feature a unique list of up to 100
preprogrammed ID numbers. A name can be assigned to each ID
in the list for your convenience.
•
W7 and W9 Control Heads: In addition to a list of 100 IDs, these
Control Heads feature unlimited Call Alert page capability using a
full, 12-button keypad.
50
General Radio Features
Sending a Call Alert Page
Press
Page
The Page indicator lights and a valid-key chirp sounds.
The display shows the last transmitted/received unit ID number.
Select a radio in one of the following ways:
•
From the ID number list:
–
Do nothing if you want to call the unit ID currently
displayed.
OR
–
Use the prestored list by turning the Mode knob (W4) or
by pressing the Mode rocker switch (W5, W7, W9) to
locate the name/ID you want to call.
OR
–
Press the Mode up !rocker switch once, and then use
the keypad to directly advance to the desired list
member.
OR
–
Enter, using the keypad, the ID of the desired unit.
Note: Using the keypad to enter the ID of another unit can only be
accomplished from the first display shown when Page was
entered. If the list has been entered, scroll to the first display.
Press
Sel
or the microphone PTT button.
The display changes to PLS WAIT (W4, W5, W7) or PLEASE
WAIT (W9).
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
51
General Radio Features
Choose one of the following:
•
When the called radio acknowledges the page, four
additional tones sound and the display changes to ACK
RCVD.
The radio returns to normal operation.
•
If you are out of the range of the system, a low-pitched tone
sounds.
Try again by pressing the PTT button or
Sel
OR
Press
HOME
operation.
•
or
Page
button to return to normal
If, after six seconds, the called unit fails to acknowledge the
alert, a low-pitched tone sounds and the display changes to
NO ACK.
Try again by pressing the PTT button or
Sel
OR
Press
52
HOME
or
Page
button to exit.
General Radio Features
Answering a Call Alert Page
If you are not available when a caller sends you a Call Alert
page, a PAGE RCV message and the caller’s ID are left.
If the page also triggers an external alarm, the display shows
PAGE RCV and four tones repeat every five seconds.
Do one of the following:
•
Make a normal dispatch call. Press the PTT button and ask
about the page.
OR
•
Press
Call
. The display shows the unit ID of the caller.
Press
to initiate an enhanced Private
Sel
Conversation or the PTT button to initiate a Private
Conversation call to the caller.
Note: Pressing any button, the PTT button, changing systems, or
or Page clears the PAGE RCV
Call
display. The original unit ID is retained until another Call
Alert or Private Conversation call is received.
pressing
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
53
General Radio Features
Storing a Unit ID Number in the List
(W7 and W9 Control Heads Only)
The Selective Call and Call Alert page features share the same
prestored list of unit IDs.
Press and hold
Page
to review the list.
The Page indicator flashes and a valid-key chirp sounds.
Press the Mode rocker switch to locate the list member you
want to change.
Press
Enter the new unit ID number on the keypad.
Sel
to select the unit ID store function.
Note: If you make an error, press the Mode down " rocker switch
or
#Del
to erase each incorrect digit.
Press
Sel
Repeat steps 2 through 5 until all the desired IDs have been
entered.
to store the new ID.
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
OR
•
54
Press
Page
to return to normal Call Alert operation.
General Radio Features
Editing a Name in the List
(W7 and W9 Control Heads Only)
The Selective Call and Call Alert page features share the same
prestored list of unit IDs.
Press and hold
Call
Page
, or
2Pge
to enter Call
ID list programming.
The Call indicator flashes and a high-pitched tone sounds.
Press the Mode rocker switch to locate the list member you
want to change.
OR
Use the numbered keys to go immediately to the location of a
member in the list. For example, press 2 to go to the second
member in the list; press 1 and 0 to go to the tenth member in
the list, and so on.
Press and hold
Change the characters or numbers using any of the numeric
keys (0 through 9) and special function keys
(*, #).
Sel
to select the name- editing function.
Note: The maximum number of characters permitted in a text line
is 8 for W7 Control Head and 11 for W9 Control Head. If you
try to add too many characters, you will hear a low-pitched
tone.
To edit, do any or all of the following:
•
To enter a character at the blinking cursor, refer to the table
on page 49.
Press the key of the desired character the number of times
shown in the table. For example, to enter the character C,
press the 2 key three times.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
55
General Radio Features
•
To leave a space in the text, press the Mode up ! rocker
switch to move the blinking cursor to the next character
position, and then enter the next character.
•
To delete characters, press the Mode down " rocker switch
to move backwards over existing characters.
When the last character on the display has been erased,
press the Mode down " rocker switch again to leave the
name-edit mode, without making any changes, and begin
the procedure again at step 2.
To save the changes, press and hold
Sel
Note: Press
momentarily to confirm changes to
Sel
numbers in the list.
Repeat steps 2 through 5 until you have modified all the desired
names,
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
OR
•
56
Press
Page
to return to normal Call Alert operation.
Conventional Radio Features
Features Used in Conventional Operation
This chapter shows you how to access features available in
conventional operation. The following topics are covered:
• Status Calls (Digital Modes Only) (page 58)
• Smart PTT (page 61)
• Conventional Talkgroup Calls (page 62)
• Conventional Talkaround (page 64)
• Selective Calls (Digital Modes Only) (page 65)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
57
Conventional Radio Features
Status Calls (Digital Modes Only)
Radio status calls are used to inform the dispatcher of the present
state of the mobile unit. For example, a status might be ENROUTE or
AT SITE.
Status names are field programmable. Each radio can have up to 8
separate statuses.
Sending a Status Call (W7 and W9 Control Heads
Only)
Press
Sts
, and the display shows the last-acknowledged
status name.
Press the Mode rocker switch to review the list of status names,
or use the keypad to enter the number of the status you wish to
send.
Note: If no button is pressed for a period of time, an inactivity
warning will sound.
The display shows the desired status name or number, press
Sel
or the PTT button to send the transmission.
One of the following conditions occur:
•
The radio display shows PLS WAIT (W7) or PLEASE WAIT
(W9) until the transmission is received and acknowledged.
When the dispatcher acknowledges the status, four highpitched tones sound, and the display shows ACK RCVD.
The radio then returns to normal dispatch operation.
•
58
If the status is not acknowledged after approximately six
seconds, the display alternates between NO ACK and the
associated status name. A low-pitched tone also sounds
continuously.
Conventional Radio Features
•
If there is no acknowledgment, do one of the following:
Press the microphone PTT button or
Sel
to resend the
status transmission.
OR
Press
HOME
to return to normal dispatch operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
59
Conventional Radio Features
Sending a Direct-Entry Keyboard (DEK) Status
(Digital Modes Only)
Press the desired Sts # button on the DEK.
The red indicator flashes while the radio is waiting for an
acknowledgment. The control head momentarily displays the
selected status, then shows PLS WAIT (W7) or PLEASE WAIT
(W9).
One of the following conditions occur:
•
When the dispatcher-acknowledge is received, four highpitched tones sound, and the status indicator lights solid and
remains on to show the last status acknowledged by the
dispatch terminal.
The display also temporarily shows ACK RCVD.
The radio then returns to normal dispatch operation.
•
If the dispatcher-acknowledge is not received, the red
indicator continues to flash, the display temporarily shows
NO ACK, and a low-pitched tone sounds. At the same time,
the indicator above the last-acknowledged status lights.
The radio then returns to normal dispatch operation.
•
60
Resend the last status.
Conventional Radio Features
Smart PTT
Smart PTT is a per-mode feature that gives the system manager
better control of radio operations. When smart PTT is enabled in your
radio, you will not be able to transmit on an active mode. If you try to
transmit (press the PTT button) on a busy or active smart PTT
channel, a continuous tone sounds until you release the PTT button,
and the transmission is inhibited.
The yellow BUSY LED lights when the radio is receiving to indicate
that the mode is busy.
Three radio-wide variations of smart PTT can be enabled on your
radio:
Transmit Inhibit on
Busy Mode with
Carrier
You will not be able to transmit if any
activity is detected on the mode.
Transmit Inhibit on
Busy Mode with
Wrong Squelch Code
You will not be able to transmit on an active
mode that has a squelch code other than
your own.
Quick-Key Override
You can override either of the two previous
transmit-inhibit states by quick-keying the
radio (two quick PTT button presses).
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
61
Conventional Radio Features
Conventional Talkgroup Calls
Digital Modes Only
This feature allows you to define talkgroups for your conventional
system. Talkgroups, combined with selective squelch operation, allow
groups of users to transparently share a conventional channel.
Talkgroups can be slaved to a personality through programming, or
you can select them.
Encryption keys are slaved to talkgroups. When conventional
talkgroups are enabled, encryption keys are changed by changing the
active talkgroup.
Selecting a Conventional Talkgroup
The Talkgroup Select feature allows you to manually select any one
of the available talkgroups.
Press the Tgrp button.
The display changes to show the last-selected talkgroup.
Turn the Mode knob (W4) or the Mode rocker switch (W5, W7,
W9) to choose a different talkgroup.
(W7 and W9 Control Heads) Talkgroups can be accessed by
direct keypad entry.
Press
Sel
to save the talkgroup.
The radio returns to the home display.
62
Conventional Radio Features
Note: To select the default talkgroup, press
Sel
while the
radio displays PRESET.
Selecting PRESET causes the radio to return to its
preprogrammed talkgroup.
To abort the talkgroup menu, press
HOME
or the PTT
button:
–
Pressing HOME exits the talkgroup select menu
without saving the selected talkgroup choice.
–
Pressing the PTT button exits the menu without saving
the selected talkgroup and allows the radio to transmit.
Note: If the encryption key slaved to the new talkgroup is erased,
the display shows KEY FAIL and a momentary tone is
generated. If the encryption key that is slaved to the new
talkgroup is not allowed, the display shows ILLEGAL KEY
and a momentary tone is generated.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
63
Conventional Radio Features
Conventional Talkaround
Talk Direct (Mobile-To-Mobile)
To talk directly to another unit without going through the conventional
repeater system:
Press
Dir
momentarily.
The Dir indicator lights, indicating that the radio is now
transmitting directly to another unit.
To return to repeater operation, press
Dir
again.
The Dir indicator goes out.
Note: A conventional personality can be configured to always
transmit on the direct mobile-to-mobile frequency. In this
case, the Dir indicator is lit continuously while the mode is
selected.
64
Conventional Radio Features
Selective Calls (Digital Modes Only)
The Selective Call feature not only allows you to carry on a
conversation that is heard only by the two parties involved, but also
enables you to determine whether the unit you are calling is in
service.
All Control Heads are capable of responding to a Selective Call
initiated by another radio. The following further describes each
Control Head’s capability:
•
All Control Heads: Feature a unique list of preprogrammed ID
numbers. A name may be assigned to each ID in the list for your
convenience.
•
W7 and W9 Control Heads: In addition to a list of IDs, these
Control Heads feature unlimited enhanced Private Conversation
(see page 74) capability using a full, 12-button keypad to call any
ID in the system.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
65
Conventional Radio Features
Answering a Selective Call
When a Selective Call is received, two high-pitched tones
sound and the display alternates between CALL RCV and the
home display.
Press
Call
within 20 seconds of receiving the call. (This
time is programmable by a qualified radio technician.)
The display shows the ID number of the calling unit.
To respond to the call, press the PTT button and talk.
If 20 seconds pass before you press
Call
, you will not
respond privately to the call just received. Instead, when you
press
Call
, you enter the Selective Call state, as
described in “Selective Calls (Digital Modes Only)” on page 65.
If the system is busy when you attempt to answer the call, a
telephone-type busy tone sounds and your radio’s BUSY
indicator lights. When a channel becomes available, you
receive a call back, and your radio automatically keys up for
three seconds so that you can begin talking.
Note: If you do not press
before pressing the PTT
Call
button, your conversation will be heard by all members of
the talk group.
66
Conventional Radio Features
Initiating a Selective Call
To initiate a Selective Call, select a unit to call, then place the call.
Press
Call
The Call indicator lights, and the display shows the last
transmitted/received unit ID number.
Select a unit in one of the following ways:
•
From the ID number list:
–
Do nothing if you want to call the unit ID currently
displayed.
OR
–
Use the prestored list by turning the Mode knob (W4) or
by pressing the Mode rocker switch (W5, W7, W9) to
locate the name/ID you want to call.
OR
–
Press the Mode up !rocker switch once, and then use
the keypad to directly advance to the desired list
member.
OR
–
Enter, using the keypad, the ID of the desired unit.
Note: Using the keypad to enter the ID of another unit can only be
accomplished from the first display shown when CALL was
entered. If the list has been entered, scroll to the first display.
Press
Sel
or the microphone PTT button.
A telephone-type ringing sounds if the unit you are calling is in
service. The display shows PLS WAIT (W4, W5, W7) or PLEASE
WAIT (W9).
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
67
Conventional Radio Features
Choose one of the following conditions that applies to your
current call:
•
If the receiving unit answers, identify yourself and begin your
Selective Call.
•
If, after a programmable time period, you are not connected,
the display shows NO ACK and a momentary, low-pitched
tone sounds.
Try again, or press
HOME
or
Call
button to return
to normal operation.
•
If you are out of the system’s range, a low-pitched tone
sounds.
Try again, or press
HOME
or
Call
button to return
to normal operation.
•
If the system is busy when you attempt to make a call, the
radio you are calling hears a telephone-type busy tone.
When a channel becomes available, the called radio
receives a call back and automatically keys up for three
seconds so that conversation can begin.
To return to normal operation, press
Note: If you do not press
HOME
or
Call
button to hang
HOME or
Call
up, your unit will remain in the Selective Call state with the
other unit. You will miss all subfleet traffic and incoming
phone calls.
68
Conventional Radio Features
Viewing Your Unit ID Number
Press
Call
momentarily to select the Selective Call
feature.
The Call indicator lights.
Do one of the following:
•
Turn the Mode knob (W4) counterclockwise or press the
Mode down " rocker switch (W5, W7, W9) to locate the MY
ID display.
OR
•
W7 and W9 Control Heads only: When not in the
scratchpad, press the * button.
The display will alternate between MY ID and your ID
number.
To return to normal operation, press
HOME
or
Call
button.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
69
Conventional Radio Features
Storing a Unit ID Number in the List
(W7 and W9 Control Heads Only)
The Selective and Call Alert page features share the same prestored
list of units’ IDs.
Press and hold
Call
Page
, or
to review
2Pge
the Call ID list.
The Call indicator flashes and a high-pitched tone sounds.
Press the Mode rocker switch to locate the list member you
want to change.
Press
Enter the new unit ID number on the keypad.
to select the unit ID store function.
Sel
Note: If you make an error, press the Mode down " rocker switch
or #Del to erase each incorrect digit.
When all the digits of the ID are entered, press
Sel
to
store the new ID.
Repeat steps 2 through 5 until all the desired IDs have been
entered.
OR
Do one of the following:
•
Press the
HOME
to return to normal radio operation.
OR
•
70
Press
Call
to return to normal Call operation.
Conventional Radio Features
Editing a Name in the List
(W7 and W9 Control Heads Only)
The Selective Call and Call Alert page features share the same
prestored list of unit IDs.
Press and hold
Call
Page
, or
2Pge
to enter the
Call ID list.
The Call indicator flashes and a high-pitched tone sounds.
Press the Mode rocker switch to locate the list member you
want to change.
OR
Use the numbered keys to go immediately to the location of a
member in the list. For example, press 2 to go to the second
member in the list; press 1 and 0 to go to the tenth member in
the list, and so on.
Press and hold
Change the characters or numbers using any of the numeric
keys (0 through 9) and special function keys
(*, #).
Sel
to select the name-editing function.
Note: The maximum number of characters permitted in a text line
is 8 for W7 Control Head and 11 for W9 Control Head. If you
try to add too many characters, you will hear a low-pitched
tone.
To edit, do any or all of the following:
•
To enter a character at the blinking cursor, refer to the table
on page 49.
Press the key of the desired character the number of times
shown in the table. For example, to enter the character C,
press the 2 key three times.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
71
Conventional Radio Features
•
To leave a space in the text, press the Mode up ! rocker
switch to move the blinking cursor to the next character
position, and then enter the next character.
•
To delete characters, press the Mode down " rocker switch
to move backwards over existing characters.
When the last character on the display has been erased,
press the Mode down " rocker switch again to leave the
name-edit mode, without making any changes, and begin
the procedure again at step 2.
To save the changes, press and hold
Sel
Note: Press
momentarily to confirm changes to a
Sel
number in the list.
Repeat steps 2 through 5 until you have modified all the desired
names.
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
Call
to return to normal Call operation.
OR
•
72
Press
Trunking Operation
Features Used on Trunking Systems
This chapter shows you how to access features available on trunking
systems. The following topics are covered:
• Enhanced Private Conversation (Digital Modes Only) (page 74)
• Failsoft (page 81)
• Dynamic Regrouping (Digital Modes Only) (page 82)
• SmartZone (W7 and W9 Control Heads Only) (page 85)
• Out-of-Range Indication (page 89)
• Trunked Announcement (page 90)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
73
Trunking Operation
Enhanced Private Conversation (Digital
Modes Only)
The enhanced Private Conversation feature not only allows you to
carry on a conversation that is heard only by the two parties involved,
but also enables you to determine whether the unit you are calling is
in service.
All Control Heads are capable of responding to a Private
Conversation call initiated by another radio. The following further
describes each Control Head’s capability:
•
All Control Heads: Feature a unique list of preprogrammed ID
numbers. A name may be assigned to each ID in the list for your
convenience.
•
W7 and W9 Control Heads: In addition to a list of IDs, these
Control Heads feature unlimited enhanced Private Conversation
capability using a full, 12-button keypad to call any ID in the
system.
74
Trunking Operation
Answering an Enhanced Private Conversation Call
When a Private Conversation Call is received, two high-pitched
tones sound and the display alternates between CALL RCV
and the home display.
Press
Call
within 20 seconds of receiving the call. (This
time is programmable by a qualified radio technician.)
The display shows the ID number of the calling unit.
To respond to the call, press the PTT button and talk.
If 20 seconds pass before you press
Call
, you will not
respond privately to the call just received. Instead, when you
press
Call
, you enter the Private Conversation Call state,
as described in “Initiating an Enhanced Private Conversation
Call” on page 76.
If the system is busy when you attempt to answer the call, a
telephone-type busy tone sounds and your radio’s BUSY
indicator lights. When a channel becomes available, you
receive a call back, and your radio automatically keys up for
three seconds so that you can begin talking.
Note: If you do not press
before pressing the PTT
Call
button, your conversation will be heard by all members of
the talk group.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
75
Trunking Operation
Initiating an Enhanced Private Conversation Call
To initiate an Enhanced Private Conversation Call, select a unit to
call, then place the call.
Press
Call
The Call indicator lights, and the display shows the last
transmitted/received unit ID number.
Select a unit in one of the following ways:
•
From the ID number list:
–
Do nothing if you want to call the unit ID in the display.
OR
–
Use the prestored list by turning the Mode knob (W4) or
by pressing the Mode rocker switch (W5, W7, W9) to
locate the name/ID you want to call.
OR
–
Press the Mode up ! rocker switch once, and then use
the keypad to directly advance to the desired list
member.
OR
–
Enter, using the keypad, the ID of the desired unit.
Note: Using the keypad to enter the ID of another unit can only be
accomplished from the first display shown when CALL was
entered. If the list has been entered, scroll to the first display.
Press
Sel
or the microphone PTT button.
A telephone-type ringing sounds if the unit you are calling is in
service. The display shows PLS WAIT (W4, W5, W7) or PLEASE
WAIT (W9).
76
Trunking Operation
Choose one of the following conditions that applies to your
current call:
•
If the receiving unit answers, identify yourself and begin your
Private Conversation.
•
If, after a programmable time period, you are not connected,
the display shows NO ACK and a momentary, low-pitched
tone sounds.
Try again, or press
HOME
or
Call
button to return
to normal operation.
•
If you are out of the system’s range, a low-pitched tone
sounds.
Try again, or press
HOME
or
Call
button to return
to normal operation.
•
If the system is busy when you attempt to make a call, the
radio you are calling hears a telephone-type busy tone.
When a channel becomes available, the called radio
receives a call back and automatically keys up for three
seconds so that conversation can begin.
To return to normal operation, press
HOME
or
Call
Note: If you do not press
button to hang
HOME or
Call
up, your unit will remain in the Private Conversation state
with the other unit. You will miss all subfleet traffic and
incoming phone calls.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
77
Trunking Operation
Storing a Unit ID Number in the
Private Conversation List
(W7 and W9 Control Heads Only)
The Private Conversation and Call Alert page features share the
same prestored list of unit IDs.
Press and hold
Page
to review the list.
The Page indicator flashes and a valid-key chirp sounds.
Press the Mode rocker switch to locate the list member you
want to change.
Press
Enter the new unit ID number on the keypad.
Sel
to select the unit ID store function.
Note: If you make an error, press the Mode down " rocker switch
or
#Del
to erase each incorrect digit.
Press
Sel
Repeat steps 2 through 5 until all the desired IDs have been
entered.
to store the new ID.
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
OR
•
78
Press
Page
to return to normal Call Alert operation.
Trunking Operation
Editing a Name in the
Private Conversation List
(W7 and W9 Control Heads Only)
The Private Conversation and Call Alert page features share the
same prestored list of unit IDs.
Press and hold
Call
Page
, or
2Pge
to enter
Call ID list programming.
The Call indicator flashes and a high-pitched tone sounds.
Press the Mode rocker switch to locate the list member you
want to change.
Press and hold
Change the characters or numbers using any of the numeric
keys (0 through 9) and special function keys
(*, #).
Sel
to select the name- editing function.
Note: The maximum number of characters permitted in a text line
is 8 for W7 Control Head and 11 for W9 Control Head. If you
try to add too many characters, you will hear a low-pitched
tone.
To edit, do any or all of the following:
•
To enter a character at the blinking cursor, refer to the table
on page 49.
Press the key of the desired character the number of times
shown in the table. For example, to enter the character C,
press the 2 key three times.
•
To leave a space in the text, press the Mode up ! rocker
switch to move the blinking cursor to the next character
position, and then enter the next character.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
79
Trunking Operation
•
To delete characters, press the Mode down " rocker switch
to move backwards over existing characters.
When the last character on the display has been erased,
press the Mode down " rocker switch again to leave the
name-edit mode, without making any changes, and begin
the procedure again at step 2.
To save the changes, press and hold
Repeat steps 2 through 5 until you have modified all the desired
names,
Sel
OR
Do one of the following:
•
Press
HOME
to return to normal radio operation.
OR
•
80
Press
Page
to return to normal Call Alert operation.
Trunking Operation
Failsoft
If the trunked system’s central controller fails for any reason, the radio
indicates failsoft. In this condition, the radio transmits and receives on
a pre-determined frequency in a conventional mode.
Failsoft ensures that you will have communications capability at all
times. Radios can be programmed by the system administrator so
units that normally communicate on the same trunked mode will be
assigned to the same failsoft repeater frequency.
Since the normal trunking features do not operate during failsoft,
much of the privacy of trunked systems is lost. You must share the
channel with other users until the failure is corrected.
To continue, in Failsoft, to communicate with other talkgroups:
1 Rotate the Mode knob (W4) or press the Mode (W5, W7, W9)
rocker switch to change to a different repeater frequency.
The failsoft condition is indicated by a faint beeping tone every
ten seconds (radio unsquelched).
When the trunking system returns to normal operation, the
beeping tone stops.
Press the PTT button to talk, and release the button to listen.
Failsoft:
If a system that is in failsoft is accessed while in scan, the radio
freezes scan and remains on the failsoft frequency for a period of six
seconds. This time period can be changed by a qualified radio
technician. This allows the operator to monitor the failsoft frequency
for activity before resuming scanning.
On W7 and W9 Control Heads, the nuisance-delete feature can be
used to temporarily delete the system in failsoft from the scan list, if
desired.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
81
Trunking Operation
Dynamic Regrouping (Digital Modes Only)
The dynamic regrouping feature allows the dispatcher to temporarily
reassign selected individuals, operating in separate trunked
talkgroups, into a single group so that they can communicate.
Receiving a Dynamic Regrouping ID Assignment
(W7 and W9 Control Heads Only)
When your unit receives a dynamic regrouping ID assignment, a
unique chirp sounds to alert you that your unit has been dynamically
regrouped. The display shows the new dynamic mode name
assignment. Examples of the field-programmable dynamic mode
names include 16 DYNMC, 8 TACTCL.
•
Press the PTT button. The radio makes a chirp and transmits
on the dynamically assigned mode.
After the dispatcher releases your mobile from the dynamic
ID assignment, your radio returns to the last selected, nondynamic regrouping mode.
•
82
If no dynamic regrouping assignment has been made, a lowpitched tone sounds if you attempt to select a dynamic
mode.
Trunking Operation
Selecting Enable and Disable (Digital Modes Only)
The dispatcher may classify regrouped units into one of two
categories: select-enabled or select-disabled.
Select-enabled
Units are free to make mode changes to any of
the available talkgroups, including the dynamic
group.
Select-disabled
Units cannot change modes because the
dispatcher has specifically chosen to force the
unit to remain in the dynamic mode.
Requesting a Dynamic Regrouping
(W7 and W9 Control Heads Only) (Digital Modes Only)
Press
Rpg
(W7) or
Rpgm
(W9) to request regrouping.
A high-pitched tone sounds, indicating your request was received by
the system’s central controller.
The display changes to RPGM (W7) or RPGM RQST (W9) while the
request is being processed.
If the regrouping request is acknowledged, a dispatcheracknowledge signal sounds (four high-pitched tones), and the
display shows ACK RCVD.
The radio then returns to normal operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
83
Trunking Operation
If the regrouping request is not acknowledged within six to eight
seconds, the display alternates between showing NO ACK and RPGM
or (W9 Control Head) RPGM RQST, and a low-pitched tone sounds.
At this time, do one of the following:
•
Press the microphone PTT button or
Sel
regroup request.
OR
•
84
Press
HOME
to return to normal operation.
to resend the
Trunking Operation
SmartZone (W7 and W9 Control Heads Only)
The SmartZone® feature extends communications beyond the reach
of a single-trunked site (antenna location) when operating in a
SmartZone system. SmartZone units provide expanded wide-area
coverage.
SmartZone automatically switches the radio to a different site when
the current site signal becomes unacceptable. This usually happens
when the vehicle in which the radio is located is driven out of the
range of one site, and into the range of another.
Under normal conditions, a SmartZone-enabled radio functions
invisibly to the operator. However, the operator does have some
manual controls on the W7 and W9 Control Heads: the Site and Lock
buttons. These buttons can be used to check, or change, the
SmartZone operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
85
Trunking Operation
Site-Button Operation
To check which site the radio has currently selected:
Press
Ste
(W7) or
Site
(W9) momentarily.
The display momentarily shows the current site name and RSSI
(received signal strength indicator).
One of the following conditions can also occur:
•
If the radio is not locked onto a site, but is scanning for a new
site, the display shows SCANNING.
•
If the radio has not yet received site ID information for the
current site, the radio displays SITE XX.
Note: You can also initiate scanning to another site by holding
down
86
Ste
until the display shows SCANNING.
Trunking Operation
Locking onto a Site
In areas that commonly have weak signals, use the SmartZone lock
function to prevent the radio from automatically scanning for a new
site.
Press
Lck
(W7) or
Lock
(W9) momentarily to display
the current lock status.
W7 Control Head: Either the display shows LOCKED or
UNLOCKED.
W9 Control Head: Either the display shows SITE LOCKED or
SITE UNLCKD.
To change the locked or unlocked condition, press and hold
Lck
(W7) or
Lock
(W9) until a tone sounds and the
display changes.
After temporarily displaying the new condition, the radio returns
to normal operation.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
87
Trunking Operation
Site Trunking
In a SmartZone system, if the zone controller for a particular site fails,
the site enters into a site-trunking operational mode. In this mode of
operation, the user can only communicate with other units at the
same site.
Radios in a SmartZone system can be programmed by a qualified
radio technician to display STE TRNK (W7) or STE TRUNK (W9) when
site trunking becomes active. The display alternates with the current
mode display as long as the radio remains in site trunking. The radio
also sounds a valid-key chirp when it first detects site trunking.
88
Trunking Operation
Out-of-Range Indication
The out-of-range display/audible indication feature can be enabled by
a qualified radio technician. The display alternately shows OUT OF
RANGE and the current selected mode, and a low-pitched tone sounds
every six seconds:
•
When the radio is out of range of the system and can no longer
lock onto the control channel
OR
•
When the radio is in failsoft and cannot lock onto the failsoft
channel.
The out-of-range indication remains in effect until one of the following
conditions occur:
•
The radio locks on a control channel
•
The radio locks on a failsoft channel
•
The radio is turned off
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
89
Trunking Operation
Trunked Announcement
The announcement capability allows a user to make announcements
to the entire user group, as well as monitor talkgroup calls and other
announcements.
Announcement calls are handled in two different ways, depending on
the trunked central controller configuration. The two types are called
ruthless and non-ruthless preemption.
•
Ruthless Preemption: When a ruthless preemption
announcement call is initiated, the requesting radio begins
transmitting immediately. All associated talkgroup calls taking
place on other channels are immediately halted, and the radios
are steered to the announcement call.
Transmitting radios continue to transmit until the PTT button is
released, at which time they also unmute for the announcement
call. Individual calls (Private Conversation and telephone
interconnect) are not affected.
•
Non-Ruthless Preemption: When a non-ruthless preemption
announcement is initiated, the initiating unit receives a telephonetype busy tone, followed by a call back when all associated
talkgroup conversations end.
Once an announcement call is pending, any attempts by other
users to initiate a talkgroup call will result in a telephone-type busy
tone. These users will not receive a call back until the
announcement call is complete.
90
Trunking Operation
Initiating an Announcement
If your radio has been programmed to allow announcement calls:
Turn the Mode knob (W4) or press the Mode rocker switch (W5,
W7, W9) to locate the announcement-group mode.
Press the microphone PTT button to initiate the announcement.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
91
Trunking Operation
Notes
92
Secure Operation
Features Available on Secure XTL 5000
This chapter covers features available on XTL 5000 Digital Mobile
Radios with secure encryption. The following topics are covered:
• Receiving a Private Message (page 94)
• Transmitting a Private Message (page 94)
• System Considerations (page 95)
• Loss Indication (page 96)
• Selecting an Encryption Key (Conventional Only) (page 97)
• Selecting an Encryption Index (Conventional Only) (page 99)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
93
Secure Operation
Receiving a Private Message
Select a mode by turning the Mode knob (W4) or pressing the
Mode rocker switch (W5, W7, W9).
Using the Volume knob (W4) or the Vol rocker switch (W5, W7,
W9), adjust the volume to a comfortable listening level.
In conventional modes and, if enabled, in trunking modes, the
BUSY light blinks and the radio unmutes when the radio is
receiving a private message.
Note: The secure on/off state does not affect received messages.
The radio automatically receives coded or clear messages.
Transmitting a Private Message
Press
to turn on the coded mode.
Some radio modes may have secure automatically set on or off
if the mode-strapped Secure feature is enabled.
The display shows the current key if multi-key has been
enabled.
Note: If the coded mode is selected, the D is on. If the standard
(clear) mode is selected, the D indicator is off.
Monitor the mode to be sure it is not in use.
Press and hold the PTT button to transmit.
The XMIT indicator lights, and the display shows the current key
selected when transmitting in the coded mode, if multikey and
Display on PTT are enabled.
94
Secure Operation
System Considerations
•
Trunked Systems only: If you press the PTT button when no
secure-voice channel is available, the display shows NO SEC (W4,
W5, W7) or NO SECURE (W9), and a continuous talk-prohibit tone
sounds until you release the PTT button.
•
Analog trunking systems: You are not allowed to change from
a secure transmission to a clear transmission during a secure
trunked call. If you attempt to change from a secure to a clear
transmission during a call, the radio generates a talk-prohibit tone,
and the display will show SEC ONLY or SECURE ONLY.
•
Digital trunking systems: You are allowed to change from a
secure transmission to a clear transmission during a secure
trunked call.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
95
Secure Operation
Loss Indication
When you press the PTT button while in the coded mode and without
the encryption module containing a valid key, the speaker generates
bursts of alert tones, and the display shows KEY FAIL until you
release the PTT button.
When the radio is first turned on, six medium-pitched tones sound
and the display momentarily shows KEY FAIL to indicate that the
encryption module does not contain a valid key for the current mode.
If the periodic keyfail tone feature is enabled, six medium-pitched
tones are generated every five to ten seconds while the radio is not
transmitting or receiving to remind you that the radio does not have a
valid key for the current mode. The keyfail reminder will not sound
when the radio is in clear mode.
96
Secure Operation
Selecting an Encryption Key (Conventional
Only)
The Select Key feature allows you to manually select any one of the
16 encryption keys.
If the current mode is programmed with key selection being strapped
to force the current mode to use a predetermined key, the Select Key
menu will not appear as a Secure menu item.
Press and hold down
until a tone sounds, which
indicates entry into the Advanced Secure menu.
Turn the Mode knob (W4) or press the Mode rocker switch
(W5, W7, W9) to locate the KEY SEL option.
Press
Sel
to enter the Key Selection menu.
The display changes to show the last user-selected key.
Do one of the following:
•
Turn the Mode knob (W4) or press the Mode rocker switch
(W5, W7, W9) to review the encryption keys,
OR
•
Use direct keypad entry to access the encryption keys.
Choose one of the following:
•
To save a key, press
Sel
The radio returns to the home display.
•
To select the default encryption keys on a radio-wide basis,
press
Sel
while the radio displays PRESET.
Selecting preset causes the radio to return to its
preprogrammed keys on a per-zone/-mode basis.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
97
Secure Operation
Note: When you scroll to an erased key, the display alternates
between the key name and ERASED.
To abort this menu, press
Pressing
HOME
HOME
or the PTT button.
exits the key-select menu without saving
the selected key choice.
Pressing the PTT button exits the menu without saving the
selected key choice and allows the radio to transmit.
When you abort the key-select menu, the radio uses the key
that was selected prior to entry into the menu.
98
Secure Operation
Selecting an Encryption Index (Conventional
Only)
The Select an Index feature allows you to select one or more groups
of several encryption keys from among the available keys stored in
the radio. For example, you could have a group of three keys
structured to one index, and another group of three different keys
structured to another index. By changing indices, you would
automatically switch from one set of keys to the other.
If the mobile does not support indexing, the index menu will not
appear as a Secure menu item.
Press and hold down
until a tone sounds, which
indicates entry into the Advanced Secure menu.
Turn the Mode knob (W4) or press the Mode rocker switch
(W5, W7, W9) to locate the INDX SEL option.
Press
Sel
to enter the Index Selection menu.
The display changes to show the last index that was selected
and stored after the Index Selection menu was entered.
Turn the Mode knob (W4) or press the Mode rocker switch
(W5, W7, W9) to locate the desired key index.
Choose one of the following:
•
To save an index key, press
. The radio will save
Sel
the index and return to normal operation,
•
To abort from the Index Selection menu, press
HOME or
the PTT button. (Pressing the PTT button allows the radio to
transmit.)
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
99
Troubleshooting
Troubleshooting
The following are suggestions to assist you in troubleshooting
possible operating problems.
CAUTION
The cables that connect to the rear of
the radio could have live voltage on
some of their pins. Do not remove or
reconnect these cables. Only a
qualified radio technician should
perform this task. Service performed
by unauthorized personnel may cause
the radio to transmit an emergency
alarm even if the unit is turned off.
If your radio is locked up or the display shows FL 01/90 (W4, W5,
W7) or FAIL 01/90 (W9), turn the radio off and then back on. If this
does not correct the condition, take the radio to a qualified radio
technician for service.
If radio operation is intermittent, check with other persons using the
system for similar problems before taking the radio in for service.
Similar problems indicate a system malfunction rather than a radio
failure.
If symptoms persist or, if your unit exhibits other problems, contact a
qualified radio technician.
100
Glossary
ACK
Acknowledgment of communication.
Channel
A group of characteristics, such as transmit/
receive frequency pairs, radio parameters, and
encryption encoding.
Coded Squelch
Tone Private-Line™ or Digital Private-Line.
Used on conventional channels to make sure
you hear only the communication meant for
you.
Control Channel
In a trunking system, one of the channels that
is used to provide a continuous, two-way/data
communications path between the central
controller and all radios on the system.
Conventional
Typically refers to radio-to-radio
communications, sometimes through a
repeater. You share a frequency, or
frequencies, with other users without the aid of
a central controller to assign communication
channels. Therefore, you should monitor each
channel before transmitting to avoid interfering
with another user who may be transmitting.
Cursor
A visual tracking marker (a blinking line) that
indicates a location on the display.
Digital PrivateLine (DPL) Coded
Squelch
A continuous, sub-audible data signal,
transmitted with the carrier.
Dispatcher
An individual who has radio system
management duties.
Failsoft
A back-up system allowing you to
communicate in a non-trunked, conventional
mode should the trunked system fail.
FCC
Federal Communications Commission.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
101
Glossary
Hang Up
Disconnect.
Home Display
The first display information after the radio
completes its self test.
LCD
Liquid-Crystal Display.
Mode
A programmed combination of operating
parameters; for example, a channel or
talkgroup.
Mode-Slaving
Radio programmed to automatically give the
proper operation for a given mode you have
selected.
Monitoring
(Conventional
Operation)
Press a programmed monitor button to listen to
another user active on the channel. This way,
you may be prevented from talking over
someone else’s conversation.
Page
A one-way alert, with audio and/or display
messages.
Push-To-Talk
(PTT) button
The PTT button engages the transmitter and
puts the radio in transmit (send) operation
when pressed. Press this button to transmit;
release it to receive.
Repeater
A conventional radio feature, in which you talk
through a receive/transmit facility (repeater)
that re-transmits received signals in order to
improve communications range and coverage.
RF
Radio Frequency. A part of the general
frequency spectrum between the audio and
infrared light regions (about 10 kHz to
10,000,000 MHz).
RSSI
Received Signal Strength Indicator.
102
Glossary
Squelch
The muting of audio circuits when received
signal levels fall below a pre-determined
threshold. With carrier squelch, you hear all
channel activity which exceeds the radio’s
preset squelch level.
Standby
An operating condition whereby the radio’s
speaker is muted but still continues to receive
data.
Talkgroup
An organization (or group) of radio users who
communicate with each other, using the same
communication path.
Tone Private-Line
(PL) Coded
Squelch
A continuous sub-audible tone transmitted with
the carrier.
Trunking
The automatic sharing of communications
paths between a large number of users (see
Conventional). Allows radio users to share a
smaller number of frequencies because a
repeater, or communications path, is assigned
to a talkgroup for the length of a conversation.
Zone
A grouping of channels or talkgroups.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
103
Glossary
Notes
104
Patent Disclosure
This product is covered by one or more of the following United States patents:
4,512,035 4,551,856 4,653,117 4,816,774 4,829,594 4,837,853 4,864,252
4,885,550 4,914,321 4,918,403 4,959,617 4,975,650 4,994,768 5,006,730
5,021,754 5,079,526
Commercial Warranty (Standard)
Motorola radio communications products are warranted to be free from
defects in material and workmanship for a period of ONE (1) YEAR, (except
for crystals and channel elements which are warranted for a period of ten [10]
years) from the date of shipment. Parts, including crystals and channel
elements, will be replaced free of charge for the full warranty period, but the
labor to replace defective parts will only be provided for one-hundred-twenty
(120) days from the date of shipment. Thereafter, purchaser must pay for the
labor involved in repairing the product or replacing the parts at the prevailing
rates together with any transportation charges to or from the place where
warranty service is provided. This express warranty is extended by Motorola
Communications and Electronics, Inc., 1301 E. Algonquin Road,
Schaumburg, Illinois 60196, to the original purchaser only, and only to those
purchasing for purpose of leasing or solely for commercial, industrial, or
governmental use.
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES
EXPRESS OR IMPLIED WHICH ARE SPECIFICALLY EXCLUDED,
INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL MOTOROLA BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO THE FULL
EXTENT SUCH MAY BE DISCLAIMED BY LAW.
In the event of a defect, malfunction, or failure to conform to specifications
established by seller, or if appropriate, to specifications accepted by seller in
writing, during the period shown, Motorola, at its option, will either repair or
replace the product or refund the purchase price thereof, and such action on
the part of Motorola shall be the full extent of Motorola’s liability hereunder.
This warranty is void if:
a. the product is used in other than its normal and customary manner;
b. the product has been subject to misuse, accident, neglect, or
damage;
c. unauthorized alterations or repairs have been made, or unapproved
parts used in the equipment.
This warranty extends only to individual products, batteries are excluded, but
carry their own separate limited warranty. Because each radio system is
unique, Motorola disclaims liability for range, coverage, or operation of the
system as a whole under this warranty except by a separate written
agreement signed by an officer of Motorola.
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
105
Non-Motorola manufactured products are excluded from this warranty, but
subject to the warranty provided by their manufacturers, a copy of which will
be supplied to you on specific written request.
In order to obtain performance of this warranty, purchaser must contact a
Motorola salesperson or Motorola at the address shown above, Attention
Quality Assurance Department.
This warranty applies only within the United States.
106
Index
Symbols
800 MHz frequencies ....................2
add scan list channel ..................34
adjust
display brightness .....................6
squelch level ...........................18
volume .......................................6
alarms
activate non-permanent ..........36
activate permanent ..................37
change selected ......................38
horn and lights .........................36
initiate
emergency ...........................21
emergency call and alarm ....23
silent emergency .................24
non-permanent horn
and lights activation ..............36
non-rearmable external ...........39
optional external ......................36
permanent horn and lights
activation ................................37
rearmable external ..................39
receiving call when on .............39
alert tones .....................................8
analog
mode .........................................3
trunking system considerations 95
answer
Call Alert page .........................53
Enhanced Private Conversation
call ...................................66, 75
phone call ................................42
ASTRO mode ...............................3
automatic scanning .....................26
autoscan .....................................26
basic operation ...........................11
box, hang up (HUB) ....................36
buffered overdial ......................... 45
button
Del .......................................... 31
Dim ......................................... 39
PTT ......................................... 30
Zone up or down ..................... 34
call
answer phone ......................... 42
conventional talkgroup ............ 62
emergency .............................. 20
Enhanced Private
Conversation .................. 67, 76
initiate
emergency .......................... 22
Enhanced Private
Conversation ................ 67, 76
from phone list ..................... 42
phone number not in list ......... 44
receiving when alarms
turned on .............................. 39
Call Alert page
answering ............................... 53
description .............................. 50
placing .................................... 51
selecting unit to call ................ 51
sending ................................... 51
calls, status ................................. 58
change
mode ....................................... 12
mode in current zone .............. 13
mode not in current zone ........ 13
mode priorities ........................ 33
selected alarms ....................... 38
zone ........................................ 12
channels, conventional ................. 7
control head
operation ................................... 5
status display ............................ 8
conventional
channel ..................................... 7
mode ....................................... 15
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
107
Index
scan list ...................................26
selecting talkgroup ...................62
talkaround ................................64
talkgroup calls ..........................62
conventional mode, monitoring
activity ........................................17
current zone
change mode ...........................13
select mode .............................13
select unit to call ................ 67, 76
entering keypad characters ........ 49
external alarms ........................... 36
activate non-permanent horn
and lights .............................. 36
activate permanent horn
and lights .............................. 37
non-rearmable ......................... 39
rearmable ................................ 39
Del button ....................................31
delete
nuisance mode ........................31
scan list channel ......................35
digital trunking system
considerations ..........................95
Dim (dimmer) button ...................39
direct-entry keyboard,
send status ...............................60
display, brightness adjustment ......6
dynamic regrouping
receiving an ID assignment .....82
requesting ................................83
failsoft ......................................... 81
FLASHport technology .................. 3
frequency ranges
800 MHz .................................... 2
edit name in list ...............47, 55, 79
embedded signaling ......................2
emergencies, special
considerations ..........................25
emergency call
initiating ...................................22
trunking ....................................20
emergency call and alarm
description ...............................20
initiating ...................................23
encryption key
index selection .........................99
selecting ..................................97
Enhanced Private Conversation
answer a call ......................66, 75
description ...............................74
initiate call ..........................67, 76
108
glossary .................................... 101
hang time .................................... 27
hang up box (HUB) ..................... 36
Home
mode, selecting ....................... 14
horn and lights alarms ................ 36
HUB (hang up box) ..................... 36
identification, radio ........................ 4
indicator
N PRI (non-priority) ................. 27
Phone ...................................... 44
PRI (priority) ............................ 27
scan ........................................ 27
initiate
emergency alarm .................... 21
emergency call and alarm ....... 23
Enhanced Private Conversation
call .................................. 67, 76
phone call from list .................. 42
silent emergency alarm ........... 24
trunked announcement ........... 91
Index
interconnect, unlimited telephone 44
introduction to radios ....................1
key, encryption
index selection ........................99
selecting ..................................97
keypad
character selection sequence ..49
entering characters .................49
knob
Mode ...................................4, 29
Volume ......................................4
list
edit name ................................47
editing a name ...................55, 79
phone, place call .....................42
scan .........................................26
store phone number ................46
storing unit ID number .......54, 78
telephone interconnect ............41
live overdial .................................45
lock on a site, SmartZone ...........87
loss indication, secure operation .96
Mode
knob ....................................4, 29
rocker button ...........................29
mode
analog .......................................3
ASTRO ......................................3
changing ..................................13
changing outside current zone 13
priorities, changing ..................33
selecting ..................................13
selecting Home .......................14
selecting outside current zone .13
selection ..................................12
slaving .......................................7
transmitting (conventional) ...... 15
transmitting (trunked) .............. 15
trunked ...................................... 7
monitoring
conventional mode activity ...... 17
N PRI (non-priority) indicator ...... 27
non-priority scanning .................. 26
non-rearmable external alarms ... 39
non-ruthless preemption ............. 90
non-talkback scan ...................... 30
nuisance mode
deleting ................................... 31
restoring .................................. 32
operation
basic ....................................... 11
control head .............................. 5
scan ........................................ 26
secure ..................................... 93
SmartZone site-button ............ 86
trunking ................................... 73
operator-selectable scan ............ 26
out-of-range indication ................ 89
overdial
buffered ................................... 45
live .......................................... 45
patent disclosure ...................... 105
Phone indicator .......................... 44
phone numbers, preprogrammed 41
place phone call from list ............ 42
placing Call Alert page ................ 51
power level selection .................. 16
powering on radio ......................... 5
preemption
non-ruthless ............................ 90
ruthless ................................... 90
preprogrammed phone numbers 41
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
109
Index
PRI (priority) indicator .................27
priority scanning ..........................26
private message
receive .....................................94
transmit ....................................94
programming scan list .................34
PTT button ..................................30
PTT-ID (Push-to-Talk
identification) ............................40
Push-to-Talk
identification (PTT-ID) ...............40
radio identification .........................4
rearmable external alarms ..........39
receive
call with alarms turned on ........39
private message ......................94
requesting a dynamic regrouping 83
restore
mode priorities .........................33
nuisance mode ........................32
rocker button
Mode .......................................29
Vol (volume) ............................39
ruthless preemption .....................90
scan
autoscan ..................................26
indicator ...................................27
non-priority ...............................26
non-talkback ............................30
operation .................................26
operator-selectable ..................26
priority ......................................26
talkback ...................................30
transmit while on ......................30
turning on ................................27
scan list
add a channel ..........................34
conventional ............................26
delete a channel ......................35
110
modes ..................................... 26
programming ........................... 34
restore mode priorities ............ 33
talkgroup scan ......................... 26
trunked priority ........................ 26
viewing .................................... 29
secure operation ......................... 93
select
Call Alert page unit .................. 51
conventional talkgroup ............ 62
encryption key ......................... 97
encryption key index ............... 99
Home mode ............................. 14
mode ....................................... 12
mode in current zone .............. 13
mode not in current zone ........ 13
power level .............................. 16
volume level .............................. 6
zone ........................................ 12
selected-disabled units ............... 83
selected-enabled units ................ 83
send
Call Alert page ......................... 51
status call ................................ 58
site trunking
SmartZone .............................. 88
site-button operation, SmartZone 86
slaved programming ..................... 7
slaving, mode ................................ 7
smart PTT ................................... 61
SmartZone
description ............................... 85
lock on a site ........................... 87
site trunking ............................. 88
site-button operation ............... 86
squelch, adjusting level ............... 18
status calls
description ............................... 58
sending ................................... 58
status display, control head .......... 8
store phone number in list .......... 46
Index
talk direct (mobile-to-mobile) .......64
talkback scan ..............................30
talkgroup scan list .......................26
telephone interconnect list ..........41
time-out timer ..............................40
tones, alert ....................................8
transmit
conventional modes ................15
private message ......................94
trunked modes ........................15
with scan on ............................30
transmitting .................................15
troubleshooting .........................100
trunked
announcement
capability ..............................90
initiate ..................................91
Call Alert page .........................50
mode ...................................7, 15
priority scan list ........................26
system considerations .............95
trunking
answer phone call ...................42
emergency call ........................20
Enhanced Private
Conversation .........................74
failsoft ......................................81
initiating emergency call ..........22
operation .................................73
status calls ..............................58
telephone interconnect list ......41
unlimited telephone
interconnect ..........................44
turn on
radio ..........................................5
scan .........................................27
troubleshooting ..................... 100
unlimited telephone
interconnect ............................. 44
viewing scan list .......................... 29
Vol (volume) rocker button ......... 39
Volume knob ................................ 4
volume, adjusting ......................... 6
W4 Control Head Foldout ..............ii
W5 Control Head Foldout ..............ii
W7 Control Head Foldout ........... 113
W9 Control Head Foldout ...........113
warranty, commercial ............... 105
Zone button, up or down ............ 34
zone selection ............................ 12
unit ID number, store in list ...54, 78
units
select-disabled ........................83
select-enabled .........................83
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
111
Index
112
W7 and W9 Control Heads Foldout Page
W7 Control Head
EMERGENCY
or
SECURE
Emer
POWER
ON/OFF
or
2Pge
PHONE
MODE
CALL
SCAN
SITE PAGE
SELECT
LOCK
PWR
Phon
Mode
Scan
Call
Sel
Vol
1Ste
3Lck
4Sts
5Rpg
6Msg
7H/L
8Mon
9Dir
#Del
XMIT
DIM
BUSY
HOME
Mic
REPROGRAM
MESSAGE
HORN/LIGHTS
DIRECT
HOME
VOLUME
Rcl
PRIORITY/
NON-PRIORITY
INDICATORS
DIRECT
INDICATOR
RECALL
DELETE
MONITOR
STATUS
MAEPF-23213-A
W9 Control Head
EMERGENCY
SCAN
DIRECT
SEARCH
SECURE
PRIORITY
INDICATOR
CALL
PAGE
XMIT BUSY
DIM
Emer
Dir
Scan
Srch
Call
Pri
Non
Pri
Page Rpgm
Site
Phon
H/L
Lock
Sts
Msg
Mode
Vol
Sel
Home
Rcl
MODE
VOLUME
SELECT
HOME
RECALL
NON-PRIORITY
INDICATOR
ASTRO XTL 5000 Digital Mobile Radio with W4, W5, W7, and W9
Sql
REPROGRAM
SITE
PHONE
LOCK
HORN/LIGHTS
MESSAGE
STATUS
Del
DELETE
SQUELCH
113
PWR
Mic
POWER
ON/OFF
HOME
DIM
HOME
VOLUME
Vol
Mode
MODE
Emer
Phon
Call
or
2Pge
DELETE
#Del
MAEPF-23213-A
MONITOR
RECALL
Rcl
9Dir
6Msg
8Mon
5Rpg
4Sts
7H/L
3Lck
1Ste
LOCK
SITE PAGE
STATUS
BUSY
XMIT
Sel
SELECT
CALL
DIRECT
INDICATOR
Scan
SCAN
PHONE
PRIORITY/
NON-PRIORITY
INDICATORS
EMERGENCY
or
SECURE
REPROGRAM
MESSAGE
HORN/LIGHTS
DIRECT
Quick Reference Card
ASTRO® XTL™ 5000 Digital
Mobile Radio with W7
Control Head
3 State your FCC call sign at the beginning of each
transmission.
2 When the transmit light comes on solid and no alert
tones sound (or a talk-permit tone or ID sidetone
sounds), speak into the microphone in a normal voice.
1 Press and hold the microphone PTT button.
Transmitting
Press HOME to access the preprogrammed Home
mode.
OR
Press the Mode rocker switch to select the desired
mode
Changing Modes
6 Press HOME.
5 Press the Mode rocker switch to select squelch level.
4 To adjust squelch level, hold Mon until a tone sounds.
3 Press Mon again, or replace the microphone on the
hang-up clip to return to coded-squelch operation.
2 On conventional modes with Private-Line or Digital
Private-Line, press Mon or remove the microphone
from the hang-up clip to defeat the coded squelch.
1 Hold the Vol rocker switch down to increase or
decrease volume as desired, then release.
The display shows volume levels from 0 to 15.
Setting the Volume and Squelch
Mode
Non-Priority
Second Priority
First Priority
Delete from List
Press Sel
One time
Two times
Three times
Four times
5 Press HOME or Scan to exit.
No indicator
PRI blinks
PRI lit
NPRI lit
Indicator
4 Repeat the previous steps to continue editing the list.
3 Press the Sel button as indicated in the table below to
add or remove the displayed mode from the scan list.
Press the Rcl button to scroll through the modes
currently in the scan list.
OR
2 Press the Mode rocker switch to select the mode you
want to program.
1 Hold Scan until a tone sounds and the scan indicator
blinks.
Programming a Scan List
2 Press Scan again to stop scanning.
1 Press Scan to start a scan. If no activity exists, the
display shows your selected mode. When a scanned
channel or talkgroup becomes active, the display
shows the active mode name. The PRI and NPRI
indicators show priority.
Activating Scan
2 Press Dir again to return to repeater operation.
1 Press Dir (Direct). The Dir indicator lights.
Turning the Radio On and Off
Press the PWR button once.
Transmitting (Conventional Modes)
BASIC OPERATION
A tone sounds and the display flashes
EMERGNCY. When acknowledged, four
more tones sound and the display
shows ACK RCVD, then the radio
returns to normal operation.
The audio is muted and no display
changes take place during the alarm.
Non-Silent
Silent
Press the PTT button, or press and
hold the emergency button to stop the
emergency condition and unmute the
radio.
Indications/Actions
Alarm Type
Depending on your radio's programming, one of the
emergency sequences described in the table below
occur.
For trunked modes, emergency call (priority access to
a voice channel), silent or non-silent emergency
alarm, or emergency alarm and call is entered.
For conventional modes, a silent or non-silent
emergency alarm data transmission is sent.
Press the emergency actuator (Emer button,
footswitch, hidden pushbutton) to begin an emergency
transmission.
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Press the PTT button and talk.
After the display shows ACK RCVD (see
Non-Silent Alarm above), the radio has
priority voice-channel access.
Press the appropriate Sts # button that you wish to
send. The associated indicator blinks until an
acknowledgment is received, then it lights steadily.
Sending a Direct-Entry Keyboard Status
Transmission
To send a Call Alert page following an Enhanced
Private Conversation attempt, follow the instructions
for sending a direct-entry Enhanced Private
Conversation call.
OR
3 Press Sel or the PTT button to send a Call Alert page
to the displayed ID,
2 Press the Mode rocker switch to select other
statuses.
3 Press Sel to send the transmission. The display
flashes the selected status name until the dispatcher
acknowledges, at which time alert tones sound and
the display shows ACK RCVD. The radio then returns
to normal operation.
2 Follow the instructions for initiating a Private
Conversation to select a unit ID.
1 Press the Page button.
Initiating a Call Alert Page
If the called unit does not respond, press Sel or the
PTT button again to leave a Call Alert page message
and your ID.
A single tone followed by four tones sounds if the
called unit acknowledges the page.
OR
2 If the receiving unit answers, press the PTT button to
identify yourself and proceed with your call.
1 Press Sel or the PTT button. A single tone sounds
and the display changes to PLS WAIT, followed by
telephone-type ringing if the receiving unit is in
service.
Sending a Direct-Entry Enhanced Private
Conversation Call
1 Press Sts. The display shows the last acknowledged
status or first status name.
Sending a Status Transmission
Alarm and Call
After completing the call, press and
hold the emergency actuator until a
tone sounds to return to normal
operation.
Sending an Emergency Alarm or Call
Call (Trunked
Modes only)
Press the PTT button and talk.
Indications/Actions
A tone sounds and the display flashes
EMERGNCY.
Alarm Type
2 Press HOME or Scan to end scan list selection.
1 Press the Sel button as indicated in the table above
to designate up to two modes as priorities.
Selecting Scan Mode Priority
Press Ste momentarily. If the radio is scanning for a
new site, the display shows SCANNING.
View the Current Site
Automatic Multiple Site Selection (AMSS)
Press Rpg. A central acknowledgement tone sounds
and the display shows RPGM RQST while the request
is being processed.
When the dispatcher acknowledges, four additional
tones sound, the display shows ACK RCVD, and your
radio returns to normal operation.
Requesting Dynamic Regrouping
Press the HOME button.
Selecting a Home Zone/Home Mode
2 Press the Mode rocker switch to select the mode.
1 Press the Zone Up ! button or Zone Down "
button to scroll to the desired zone.
6 Press HOME or the PTT button to quit.
5 Press Sel to select the key.
4 Press the Mode rocker switch to select the desired
key.
3 Press Sel to enter the Key Selection Menu.
2 Press the Mode rocker switch to scroll to KEY SEL.
1 Press and hold the D button until a tone sounds.
Selecting an Encryption Key
Press and release the D button. The D indicator lights
up.
Selecting Secure Mode
To toggle to the opposite condition, press and hold
Lck until a beep sounds and the display changes to
the other condition.
The radio then returns to normal operation.
OR
2 To view its condition (locked or unlocked), press Lck
momentarily. The display shows LOCKED or
UNLOCKED.
Initiate an Enhanced Private Conversation call to the
caller.
Selecting a Zone/Mode (Optional)
1 Press Lck to lock the radio onto the current site.
Locking on a Site
Press and hold Ste until a tone sounds and the
display shows SCANNING.
Initiating a Site Scan
OR
1 Press the PTT button,
Four tones sound and PAGE RCV flashes on the
display. The tone and display repeat every five
seconds.
Answering a Call Alert Page
6 Press HOME or the PTT button to quit.
5 Press Sel to select the index.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Key Erase Menu.
2 Press the Mode rocker switch to scroll to ERASE KY.
1 Press and hold the D button until a tone sounds.
Erasing an Encryption Key
6 Press HOME or the PTT button to quit.
5 Press Sel to select the index.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Index Selection Menu.
2 Press the Mode rocker switch to scroll to INDX SEL.
1 Press and hold the D button until a tone sounds.
Selecting a Key Index
Meaning
Indicates you are transmitting.
Radio is in direct (mobile-tomobile) operation.
The display shows a mode in the
scan list with the indicated priority
level.
Telephone dialing pause. Press
Sel to continue the dialing.
Unit being called with the
Enhanced Private Conversation or
Call Alert Page feature is not in
service, or emergency alarm or
status/message transmission is
not acknowledged by dispatcher.
Unit being called with Enhanced
Private Conversation or Call Alert
Page does not respond, but is
operational.
Radio is in emergency alarm or
call state.
A mode incapable of emergency
transmission has been selected.
Radio is out of range of the
trunking system.
XMIT light on
Dir indicator lit
PRI, NPRI
indicators lit
P displayed
NO ACK displayed
NO ANSWR
displayed
EMERGNCY
displayed
NO EMERG
displayed
OUT RNG displayed
The display shows a conventional
mode with activity on it, or selected
trunked system is currently busy.
Wait for callback.
BUSY light on
Display/Light
DISPLAY AND LIGHT INDICATORS
Name
Explanation
Call Alert page has
been received.
Channel is available
for previously
requested
transmission.
System is accepting
your transmission.
Automatic Call
Back or Talk
Permit
3 Short HighTones (after
requesting a
busy channel)
(upon pressing
the PTT button)
You have an
incoming call. Press
Call, then the PTT
button, then talk.
The above two
acknowledge tones,
heard in tandem.
Dispatcher is
acknowledging your
emergency
transmission. Mobile
unit has received
your Call Alert.
Central controller
has received request
for Call Alert or
emergency alarm
transmission.
You pressed a valid
key.
Feature button
pressed is not valid
in selected mode, or
a Call Alert or
emergency alarm
was not
acknowledged.
Call Alert Page
Private
Conversation
Dispatcher or
Mobile Unit
Acknowledge
Central
Acknowledge
or Valid Key
Invalid Key
Alert
4 High-Pitched
Tones every 6
seconds
2 High-Pitched
Tones
5 High-Pitched
Tones
4 High-Pitched
Tones
1 High-Pitched
Tone
1 Low-Pitched
Tone
Type of Tone
ALERT TONES
Name
Talk Prohibit/
Out-of-Range,
or Time-Out
Timer, or Illegal
Mode
Explanation
System central
controller failure. The
radio reverts from
trunked operation to
operation similar to a
conventional
repeater.
Others may share
the channel.
Out of trunked radio
system range or
system is out of
service.
Present transmission
will soon be disabled.
You have entered a
mode where normal
system traffic will be
missed, or you
attempted something
that is not allowed.
(See examples
below.)
Examples: Not exiting phone mode after a call (radio
cannot receive fleet or subfleet calls), transmitting in
receive-only conventional mode, trying to select a dynamic
mode when no dynamic ID assignment has been made.
High-Pitched
Failsoft
Tone every 10
seconds in
unmuted receive
condition
Low-Pitched
Tone (upon
pressing the
PTT button
during Transmit)
(Operation
Error)
Type of Tone
ALERT TONES (Continued)
BUSY
Dir
MODE
Mode
Emer
XMIT
Vol
Scan
SCAN
SELECT
Sel
Srch
NON-PRIORITY
INDICATOR
HOME
Home
Pri
Non
Pri
Call
CALL
PRIORITY
INDICATOR
Sql
SQUELCH
RECALL
Rcl
Sts
H/L
Phon
Page Rpgm
PHONE
DELETE
Del
Msg
Lock
Site
DIM
Quick Reference Card
ASTRO® XTL™ 5000 Digital
Mobile Radio with W9
Control Head
3 State your FCC call sign at the beginning of each
transmission.
2 When the transmit light comes on solid and no alert
tones sound (or a talk-permit tone or ID sidetone
sounds), speak into the microphone in a normal voice.
1 Press and hold the microphone PTT button.
Transmitting
Press Home to access the preprogrammed Home
mode.
OR
Press the Mode rocker switch to scroll to the desired
mode
Changing Modes
6 Press Home.
5 Press the Mode rocker switch to select squelch level.
4 To adjust squelch level, hold Sql until a tone sounds.
3 Press Sql again to return to coded-squelch operation.
2 On conventional modes with Private-Line or Digital
Private-Line, press Sql or remove the microphone
from the hang-up clip to defeat the coded squelch.
1 Hold the Vol rocker switch down to increase or
decrease volume as desired, then release.
The display shows volume levels from 0 to 15.
Setting the Volume and Squelch
3 Press Sel or the PTT button again to dial the number
in the display.
2 Press Sel or the PTT button, and wait for dial tone.
1 Using the keypad, enter the telephone number.
Dialling or Direct Dialling a New Number
3 Press Sel or the PTT button again to dial the number
in the display.
2 Press Sel or the PTT button, and wait for dial tone.
1 Press the Mode rocker switch to scroll to the number
or name you want to call.
Dialling a Number from the Pre-Stored List
2 Press Sel or the PTT button again to dial the number
in the display.
1 Press Sel or the PTT button, and wait for dial tone.
Dialling the Number in the Display
Press Phon to select the phone function. The display
shows the last phone number dialed or a series of
dashes.
Making a Phone Call
TELEPHONE OPERATION
2 Press Dir again to return to repeater operation.
1 Press Dir (Direct). The Dir indicator lights.
Turning the Radio On and Off
Slide the power switch on the bottom of the control
unit to the left.
Transmitting (Conventional Modes)
BASIC OPERATION
2 Press the Mode rocker switch or use the keypad to
select other statuses.
1 Press Sts. The display shows the last acknowledged
status or first status name.
Sending a Status Transmission
2 After completing the call, press and hold the
emergency actuator until a tone sounds to return to
normal operation.
1 Press the PTT button and talk.
After the display shows ACK RCVD, your radio has
priority voice-channel access.
Alarm and Call
2 After completing the call, press and hold the
emergency actuator until a tone sounds to return to
normal operation.
1 Press the PTT button and talk.
A tone sounds and the display alternates between
EMERGENCY and the zone/channel.
Making a Call (Trunked Modes Only)
2 Press Home to hang up.
1 Press PHON and begin your conversation.
When a call is received, ringing tones are heard from
the speaker, and the display shows PHONE.
Answering a Phone Call in Trunked Modes
3 Press Home or Call to hang up.
2 Pause for a second, then begin the conversation.
1 Press the PTT button to initiate a Private
Conversation I or II call.
Initiating a Private Conversation II
If the called unit does not respond, press Sel or the
PTT button again to leave a Call Alert page message
and your ID.
A single tone followed by four tones sounds if the
called unit acknowledges the page.
OR
2 If the receiving unit answers, press the PTT button to
identify yourself and proceed with your call.
1 Press Sel or the PTT button. A single tone sounds
and the display changes to PLEASE WAIT, followed
by telephone-type ringing if the receiving unit is in
service.
Initiating an Enhanced Private Conversation Call
Press the appropriate Sts # button that you wish to
send. The associated indicator blinks until an
acknowledgment is received, then it lights steadily.
Sending a Direct-Entry Keyboard Status
Transmission
3 Press Sel or the PTT button to send the
transmission. The display flashes the PLEASE WAIT
until the dispatcher acknowledges, at which time alert
tones sound and the display shows ACK RCVD. The
radio then returns to normal operation.
3 Press Home or Call to hang up.
2 Press the microphone PTT button, and speak into
the microphone.
1 Press the Call button.
Two tones sound and CALL RCV flashes on the
display.
Answering a Private Conversation Call
1 Press either the microphone PTT button or the Call
button to clear the Call Alert state.
Four tones sound and PAGE RCV flashes on the
display.
Answering a Call Alert Page
To send a Call Alert page following an Enhanced
Private Conversation attempt, follow the instructions
for sending an Enhanced Private Conversation call.
OR
3 Press Sel or the PTT button to send a Call Alert page
to the ID in the display,
2 Follow the instructions for initiating an Enhanced
Private Conversation to select a unit ID.
1 Press the Page button.
Initiating a Call Alert Page
5 Press Sel to select the index.
6 Press HOME or the PTT button to quit.
To toggle to the opposite condition, press and hold
Lock until a tone sounds and the display changes to
the other condition.
The radio then returns to normal operation.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Index Selection Menu.
2 Press the Mode rocker switch to scroll to INDX SEL.
1 Press and hold the D button until a tone sounds.
Selecting a Key Index
6 Press HOME or the PTT button to quit.
OR
2 To view its condition (locked or unlocked), press
Lock momentarily. The display shows SITE LOCKED
or SITE UNLCKD.
1 Press Lock to lock the radio onto the current site.
Locking on a Site
Press and hold Site until a tone sounds and the
display shows SCANNING.
Initiating a Site Scan
5 Press Sel to select the key.
4 Press the Mode rocker switch to select the desired
key.
3 Press Sel to enter the Key Selection Menu.
Viewing the Current Site
Press Site momentarily. If the radio is scanning for a
new site, the display shows SCANNING.
2 Press the Mode rocker switch to scroll to KEY SEL.
1 Press and hold the D button until a tone sounds.
Selecting an Encryption Key
Press and release the D button. The D indicator lights
up.
Selecting Secure Mode
Automatic Multiple Site Selection (AMSS)
Press Rpgm. A central acknowledgement tone
sounds and the display shows RPGM RQST while the
request is being processed.
When the dispatcher acknowledges, four additional
tones sound, the display shows ACK RCVD, and your
radio returns to normal operation.
Requesting Dynamic Regrouping
6 Press HOME or the PTT button to quit.
5 Press Sel to select the index.
4 Press the Mode rocker switch to select the desired
index.
3 Press Sel to enter the Key Erase Menu.
2 Press the Mode rocker switch to scroll to ERASE KY.
1 Press and hold the D button until a tone sounds.
Erasing an Encryption Key
3 Press HOME or the PTT button to quit.
2 Press Sel to erase the key.
1 Press and hold the D button until a tone sounds. The
display changes to ERASE KY.
Erasing an Encryption Key (Single-Key Option
Only)
Mode displayed is second priority.
Mode displayed is non-priority.
Telephone dialing pause. Press
Sel to continue the dialing.
Unit being called with the
Enhanced Private Conversation or
Call Alert Page feature is not in
service, or emergency alarm or
status/message transmission is
not acknowledged by dispatcher.
Scan list full. Delete a mode
before adding another.
Trunked phone interconnect is
busy.
Unit being called with Enhanced
Private Conversation or Call Alert
Page does not respond, but is
operational.
Radio is in emergency alarm or
call state.
A mode incapable of emergency
transmission has been selected.
Radio is out of range of the
trunking system.
Non Pri lit
P displayed
NO ACK displayed
LIST FULL
displayed
PHON BSY displayed
NO ANSWER
displayed
EMERGENCY
displayed
NO EMERGNCY
displayed
OUT OF RNGE
displayed
Mode displayed is first priority.
Pri indicator blinks
Pri indicator lit
Indicates you are transmitting.
XMIT light on
Meaning
Displayed conventional mode has
activity on it, or selected trunked
system is currently busy. Wait for
callback.
BUSY light on
Message
DISPLAY AND LIGHT INDICATORS
Name
Explanation
Phone-Type
Busy Tone
(when pressing
the PTT button)
4 High-Pitched
Tones every 6
seconds
Call Alert page has
been received.
All system radio
channels in use.
Release the PTT
button, and wait for
callback.
Call Alert Page
System Busy
You have an
incoming call. Press
Call, then the PTT
button and talk.
2 High-Pitched
Tones
Dispatcher is
acknowledging your
emergency
transmission. Mobile
unit has received
your Call Alert.
Central controller
has received request
for Call Alert,
emergency alarm,
reprogram request,
or status/message
transmission.
You pressed a valid
key.
Feature button
pressed is not valid
in selected mode, or
a Call emergency
alarm was not
acknowledged.
The above two
acknowledge tones,
heard in tandem.
Private
Conversation
Dispatcher or
Mobile Unit
Acknowledge
Central
Acknowledge
or Valid Key
Invalid Key
Alert
5 High-Pitched
Tones
4 High-Pitched
Tones
1 High-Pitched
Tone
1 Low-Pitched
Tone
Type of Tone
ALERT TONES
Motorola, Inc.
8000 West Sunrise Boulevard
Ft. Lauderdale, FL 33322
MOTOROLA, the Stylized M Logo, and ASTRO are registered
in the U.S. Patent and Trademark Office. All other product or
service names are the property of their respective owners.
© Motorola, Inc. 2003, 2004.
All rights reserved. Printed in U.S.A.
*6881096C68*
6881096C68-B

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2004:02:19 13:06:48-05:00
Create Date                     : 2004:01:30 11:51:33Z
Page Count                      : 144
Creation Date                   : 2004:01:30 11:51:33Z
Mod Date                        : 2004:02:19 13:06:48-05:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : csd099
Metadata Date                   : 2004:02:19 13:06:48-05:00
Creator                         : csd099
Title                           : 96C68_B.book
Page Mode                       : UseOutlines
Has XFA                         : No

EXIF Metadata provided by EXIF.tools