Motorola Solutions 92FT7089 Mobile 2-Way Portable Radio with Bluetooth, Bluetooth LE and WiFi User Manual Installation Manual 4 of 4

Motorola Solutions, Inc. Mobile 2-Way Portable Radio with Bluetooth, Bluetooth LE and WiFi Installation Manual 4 of 4

Installation Manual 4 of 4

MN003109A01_aaOptions and Accessories Installation Motorola Branded SB9600 Siren Connection to APX 8500 4-114.5 Motorola Branded SB9600 Siren Connection to APX 8500Figure 4-10.  J600 Accessory Connector Y-Cable KT000247A01Figure 4-11.  Pinout for cable KT000247A01 CABLE 2CABLE 1P1P2P3#21 #11 #8 #1#26 #20 #13 #7 #13#1#7 #13 #20 #26#1 #8 #14 #21#25#1434013022 AWG YELLOWSPIRAL22 AWG BROWNSPIRALSPIRAL22 AWG ORANGE22 AWG WHITESPIRAL22 AWG BLACK22 AWG PINK22 AWG PURPLE22 AWG GRAY22 AWG TAN22 AWG DRAIN22 AWG BLUE22 AWG RED22 AWG GREEN18 AWG RED18 AWG YELLOW22 AWG LIGHT BLUE22 AWG LIGHT GREEN18 AWG ORANGE18 AWG BROWN22 AWG  BROWN/WHITE22 AWG BLACK/WHITE18 AWG BLACKP31CUTCUT4567CUTCUT101112131415161718192021222324252622 AWG YELLOWSPIRAL22 AWG BROWNSPIRALSPIRAL22 AWG ORANGE22 AWG WHITESPIRAL22 AWG BLACK22 AWG PINK22 AWG PURPLE22 AWG GRAY22 AWG TAN22 AWG DRAIN22 AWG BLUE22 AWG RED22 AWG GREEN18 AWG RED18 AWG YELLOW22 AWG LIGHT BLUE22 AWG LIGHT GREEN18 AWG ORANGE18 AWG BROWN22 AWG  BROWN/WHITE22 AWG BLACK/WHITE18 AWG BLACKP210/1151423CUTCUT19238/174CUTCUT18/21131CUT15CUT256/9CUT1220/221624P11234567891011121314151617181920212223242526CONNECTIONDr-10.  J600 Accessory Con10.  J600 AccessoDDraftraaarararaaaafafaftaftftftttafafafafafafafafafaffffffSPIRAL22 AWG BROWNSPIRALPIRALAWG O22 AP11234CONNEC
MN003109A01_aa4-12 Options and Accessories Installation Motorola Branded SB9600 Siren Connection to APX 8500Figure 4-12.  Interfacing the Y-cable to the Motorola Branded SB9600 Siren and External Accessories The Y-cable KT000247A01 is primarily designed to allow for simultaneous operation of the Motorola Branded SB9600 siren and still retain duplicate access to all the MAP (J2) connector pins located on the APX 8500 remote TIB. Use of emergency accessories, speakers, programming cables, VIPS, etc are possible via the P3 connector of Y-cable KT000247A01. The 25pin connector P2 does not contain every signal from the legacy DB25 port, called J600 on the APX 7500. Therefore, some legacy functionality (i.e. A+) is reduced with the APX 8500 remote mount configuration compared to the APX 7500 remote mount configuration.NOTE: Only USB 1.5 meter data cable HKN6163_ is approved for use in series with the Y-cable KT000247A01 at connector P3. USB 4 meter data cable HKN6172_ is not approved for use in series with the Y-cable at connector P3.Siren CableDrafto the Motoo the Mot01 is primarily designed t01 is primarily desigd still retaind still  duplicate acceduplicatse of se of emergency accessoremergency accnector of Y-cablf Y-cable KT00024e Kcy DB25 port, calleDB25 port, called J600 ded with the APd with the AX 8500 remoX 850on.N6163_ is aN6163_ ispproved for usepproved for umeter data cable HKN6meter data cable HK
MN003109A01_aaOptions and Accessories Installation Compatibility of Emergency when Attaching a Motorola Branded SB9600 Siren4-4.6 Compatibility of Emergency when Attaching a Motorola Branded SB9600 SirenWhen using emergency footswitch or pushbutton with siren/PA configuration, REMOVE pin 8 (emergency) from the siren connector of the HKN4363_ siren cable as follows:Figure 4-13.  Field adjustment for Emergency Operation with Siren Accessory 1. Remove the knob from the siren/PA cable connector.2. Remove all four screws from the connector in the siren/PA cable.3. Open the connector cap and locate pin 8.4. Using the contact removal tool (6684690C02), remove pin 8 from the connector.5. Put the connector cap in place and proceed to reinstall the four screws and the knob.Figure 4-14.  Location for Pin 8Siren Cable123          4567           89AB29303132 3334 3536  37232425261617181910111213 1415 2021222728Pin 8Drathe sirethe sireews from the cews from the ctor cap and locate pinctor cap and locatct removal tool (6684690Cct removal tool (6cap in place and proceed toap in place and proraftraftaftaftfafafaffftftftftftfttftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftftfttttttffffffafafafafafafafaftttftftftftftftftaftaftaftftaftaftftaftaftaftaftaftaftaftafafaffafaffftafftftftftftafafaaafafafaaaaaaaaaaaftffa124       2416619112
MN003109A01_aa4-14Options and Accessories Installation Compatibility of Emergency when Attaching a Motorola Branded SB9600 Si-NotesDraft
Chapter 5 Motorcycle Radio Installation5.1 Motorcycle Radio DescriptionThe motorcycle model includes all the same components in the standard radio. The following paragraphs describe the unique items provided with the motorcycle models.   A small label is included with the motorcycle radio, which can be placed on the radio to identify it as a motorcycle radio. The label should be placed on a flat and protected area to avoid damage during handling. See Figure 5-1.Figure 5-1.  Identification of a Motorcycle Radio by Using a Label5.1.1 Transceiver EnclosureThe transceiver is mounted in the weather-resistant enclosure that consists of a bottom housing and a hinged top cover. The top cover has a locking latch that requires a key to open. The enclosure is mounted above the rear motorcycle wheel, oriented so that the lock is forward and the hinged cover opens toward the rear of the motorcycle. The bottom housing has a grommeted hole for cable entry and weep holes to permit water drainage.The enclosure is mounted on the motorcycle with a universal mounting plate and shock and vibration isolators. A large, braided ground-strap (installed between the mounting plate bolts and the motorcycle frame) grounds the transceiver.5.1.2 Control/Display UnitAll radio functions, except push-to-talk (PTT), are activated from the control head, which also is weather-resistant. The control head and the external speaker are mounted for easy access near the center of the handlebars. The control head is positioned for unobstructed viewing, and it may be tilted on the horizontal axis for ease of viewing. The microphone cable port on the front of the control head is plugged and is not used. 5.1.3 Control Head CableThe control-head cable connects the control head to the transceiver. The cable is routed along the motorcycle’s frame and has weather-resistant connections at both ends. Excess cable is coiled under the transceiver inside the weather-resistant enclosure.Each end of the cable is strain-relieved with jackscrews at the control head and the transceiver.  The cable is shielded to reduce the effects of radio frequency interference and ignition sense noise.Drafttion of tioa Motorcycle Radioa Motorcycleresistantsista enclosure that cenclosure thatg latch that requiresg latch that requireted edso that the that m 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
MN003109A01_aa5-2 Motorcycle Radio Installation Motorcycle Radio Description5.1.4 MicrophoneA weather-resistant, palm microphone and coiled cord plug into a pigtail connector on the control cable. The microphone attaches to a hang-up bracket located within easy reach of the motorcycle rider. The coiled cord is long enough to be operated by someone standing next to the motorcycle, yet short enough to not interfere with the motorcycle’s steering or operation.5.1.5 External SpeakerA 3.2-ohm, 10-watt-rated-audio-power, external speaker is mounted on the front of the motorcycle. The speaker cable is routed along the motorcycle frame to the transceiver’s rear accessory connector. A sealed, weather-resistant, speaker-muting (toggle) switch is mounted on top of the speaker.The external speaker connects to the rear accessory connector of the transceiver.5.1.6 Headset CapabilityThe motorcycle radio is compatible with various headset accessories that provide hands-free operation of the radio. Motorola does not manufacture headset equipment, but provides the interconnection for headset equipment with the motorcycle radio. Aftermarket headset equipment is available through Motorola (see Appendix A: Replacement Parts Ordering).5.1.7 AntennaThe antenna(s) are mounted on top of the transceiver’s weather-resistant enclosure.  The enclosure’s metal lining acts as the antenna’s ground plane.5.1.8 Ignition Sense (ACC) WireThe ignition sense wire connects to the motorcycle’s fuse box and is routed along the motorcycle frame to the transceiver’s rear accessory connector.The radio is wired so that transmission is inhibited if the motorcycle’s ignition sense switch is off.  If the PTT switch is pressed with the ignition sense off, a low-frequency tone sounds. The receiver is controlled by the control head on/off switch.To avoid loud audio, refer to the CPS help menu for audio settings if the Motorola mobile radio is used with any motorcycle helmet headset.!C a u t i o nraftnsceiver’s weather-resistaceiver’s weather-ress ground plane.ground plane.Dradio, refer to the CPS helpdio, refer to the CDs mement wnt we e Appendix AAppendix Ad with any motorcycle helmd with any motorcyDra
MN003109A01_aaMotorcycle Radio Installation Installation Overview 5-35.2 Installation Overview5.2.1 GeneralAll APX mobile radios are tested and inspected before shipment. It is, however, suggested that the transmitter frequency, deviation, and power output be checked at the time of installation. It is the license holder’s responsibility to ensure that the operating parameters of his station comply with applicable laws governing radio communications equipment. For tests and alignment procedures, refer to the appropriate service manual (refer to “Related Publications”.Generally, the installation of the motorcycle radio takes place in the following parts:• Mounting the universal mounting plate and related hardware at the rear of the motorcycle;• Mounting the control head, speaker, microphone, and related hardware forward on the motorcycle;• Routing the power cable, control-head cable, speaker cable, and ignition sense cable to the weather-resistant enclosure;• Mounting the weather-resistant enclosure and radio chassis, and connecting the cables;• Mounting the antenna(s) to the weather-resistant enclosure.A universal mounting plate, supplied by Motorola, is first mounted to either a motorcycle carrier at the rear of the motorcycle or to the rear frame of the motorcycle itself. The mounting procedures for the universal mounting plate vary from motorcycle to motorcycle. Therefore, the procedures given in this manual for installing the mounting plate may not specifically apply, but are provided for guidance.The control head, speaker, and microphone are mounted forward on the motorcycle, on or near the steering column. There are several possible mounting configurations which use a combination of Motorola and customer-built brackets. These configurations are outlined in this manual. Because of the large number of motorcycle makes and models in existence, the customer-built brackets are necessary to tailor the mounting of the Motorola equipment to the particular motorcycle being used. Suggestions for customer-built brackets are given in this manual.The power cable, control-head cable, speaker cable, and ignition sense cable are routed to the weather-resistant enclosure position. The enclosure and the radio chassis are then mounted. Special care is required when connecting cables to the radio equipment within the enclosure.Drafto to the whe supplied supplby Mby Mto the rear frame ofto the rear frameate vary from motorcycle tte vary from motormounting plate may not smounting plate maand microphone are moand microphone areunveral possible mountipossible mounng cockets. These configurkets. These configuationkes and models and models in existencin existenMotorola equipment to theMotorola equipment to thare given in this manual.are given in this manual.r carcble, and ignition sble, and ignitionsure and the radiure and the radio equipmeequip
MN003109A01_aa5-4 Motorcycle Radio Installation Installation Overview5.2.2 Important Motorcycle Installation HintsConsider the following when mounting the radio components:• Excess lengths of control-head, power, ignition sense, and speaker cables must be routed in the enclosure as shown in Figure 5-19.• All components must be mounted securely in order to withstand the constant and sometimes severe vibration experienced on a motorcycle.• No cantilever action, which could cause severe vibration, should be generated in the mounting hardware.• The control head and microphone must be placed for ease of accessibility by the motorcycle operator.• Forward components (control head, microphone, and speaker) should not interfere with visual or physical access to controls and instruments.• Forward components should not interfere with the handling of the motorcycle.• Cabling between the control head and the radio chassis should be run to minimize interference with operator movements.• The weather-resistant enclosure should be placed to avoid any interference with the motorcycle operator.• Electrical continuity must be present through the enclosure shock mounts to the motorcycle frame for proper electrical and RF grounding.• The antenna(s) are designed for mounting on the top of the weather-resistant enclosure and an adequate metal ground plane.• Only the supplied microphone mounting clip should be used to ensure secure mounting of the microphone. This clip has a very strong spring to ensure positive retention of the microphone over rough terrain. Also, there must be electrical continuity from this clip to the motorcycle frame for DC grounding.• Direct access to the microphone should be provided from both sides of the motorcycle.• Sufficient slack in the microphone coiled cord should be allowed so as not to impede steering.• Mounting hardware must be stainless steel to prevent corrosion.• If an extra length of cable is used to extend the microphone, ensure that the added capacitance does not interfere with the operation of the radio.• A suitable covering should be applied to the DB-9 receptacle when the water resistant microphone (HMN1079) is not connected.Draftosure shoosure shomust be present througmust be present thctrical and RF grounding.ctrical and RF grousigned for mountingsigned for mounting on thelane.anee mounting clip should be mounting clip shouy strong springy strong spri to ensure pto est be electrical continuity fre electrical continuity frbe eprovided from both sidprovided from both d should be alloweshould be allowevent corroent cophoph
MN003109A01_aaMotorcycle Radio Installation Installation Overview 5-55.2.3 Parts IdentificationThe following installation procedures refer to Figure 5-2 through Figure 5-20. Detailed descriptions of the mounting hardware used in each procedure are provided in parts lists located in the exploded views located in the APX Mobile Basic Service Manual (see related documentation). Those parts supplied by Motorola are contained in one of the following kits:• Motorcycle Weather-Resistant Microphone• Motorcycle Weather-Resistant Speaker with Mute Switch• Motorcycle Hardware Kit SECURENET or Motorcycle Hardware Kit• Motorcycle Power Cable Kit• Motorcycle Mounting Kit• Weather-Resistant Enclosure• Antenna5.2.4 Order of InstallationBefore starting the installation, familiarize yourself with the mounting hardware (see Figure 5-2 through Figure 5-20). Perform the installation procedures in the order that follows.1. Install the universal mounting plate on the motorcycle.2. Install the control head and speaker.3. Install the microphone hang-up clip.4. Install antenna base and cable onto enclosure.5. Install the cables.6. Install the weather-resistant enclosure on the universal mounting plate.7. Route the cables inside the weather-resistant enclosure.8. Install the transceiver in the weather-resistant enclosure.9. Install the antenna(s) on the enclosure.Draftamiliamilm the instam the instaal mounting plate oal mounting platrol head and speaker.rol head and speakhone hang-up clip.hone hang-up clip.and cable onto enclosureand cable onto encenclososure on the universaure on the uather-resistant enclosure.her-resistant enclosure.er-resistant enclosure.r-resistant enclosure.
MN003109A01_aa5-6 Motorcycle Radio Installation Installing the Universal Mounting Plate5.3 Installing the Universal Mounting PlateThe universal mounting plate, supplied with the motorcycle radio, must be mounted on the motorcycle first. It provides the base on which the weather-resistant enclosure is to be mounted.  The method used for mounting the plate depends on the make and model of the motorcycle and whether the plate is mounted to a carrier or to the motorcycle chassis. After the plate has been securely mounted to the motorcycle, mounting the weather-resistant enclosure onto the plate is straightforward.Figure 5-2 illustrates the universal mounting plate mounted to a motorcycle carrier. Since there are so many makes and models of motorcycles and motorcycle carriers, it is impossible to give specific step-by-step instructions for mounting the universal mounting plate. However, noting the following considerations will aid in the installation procedure.• A minimum of holes are predrilled into this plate as supplied. Mounting holes must be drilled as required for the particular motorcycle on which the plate is being mounted.• The universal mounting plate should be mounted on the motorcycle in such a manner that the later mounting of the weather-resistant enclosure will not interfere with the motorcycle seat back, with any other obstacles, or with the motorcycle operator. The enclosure may be temporarily bolted to the universal mounting plate and the unit positioned on the motorcycle to ensure the above criteria are met.• To ensure a good grounding path from the universal mounting plate to the motorcycle carrier or frame, stainless steel lock washers must be used with the mounting hardware in two areas to score through the paint on the universal mounting plate and on the carrier or frame, thereby, providing good electrical contact with the underside of the motorcycle carrier or motorcycle frame.Figure 5-2.  Universal Mounting Plate Installation (Part of Radio Enclosure Kit)Follow the procedures below to mount the universal mounting plate to the motorcycle  (see Figure 5-2).1. Determine the mounting position for the mounting plate.2. Determine whether stainless steel spacers are required for clearance in mounting the plate.3. Drill four 9/32-inch holes in the mounting plate and the corresponding motorcycle carrier or chassis for mounting the plate.4. Attach the universal mounting plate to the motorcycle using four machine screws, eight lock washers, and four nuts. Tighten screws securely. The lock washers must cut through the paint on the plate and motorcycle carrier or frame to ensure a good ground path.Drafversal versal are met.are met.nding path from thending path from el lock washers must beel lock washers muaint on the universal mountint on the universal contact with the undersidal contact with the u
MN003109A01_aaMotorcycle Radio Installation Installing the Speaker and Control Head 5-75.4 Installing the Speaker and Control HeadNOTE: To disable the internal speaker of the O2 Control Head, please refer to Section 2.5.1: “Internal Speaker Disassembly” .The control head mounting location and configuration is determined largely by the make and model of motorcycle. Two different mounting configurations are described below. One involves mounting the speaker and control head together as a unit using the combination speaker/control-head bracket (shown in Figure 5-4) supplied by Motorola. Alternately, the control head may be mounted by itself using a smaller control-head bracket supplied by Motorola. In this case, the speaker is mounted elsewhere. This section outlines installation procedures for each configuration mentioned above. The customer (or installer) is in the best position to determine the most appropriate mounting configuration for the control head and speaker based on the particular motorcycle on which the equipment is to be mounted. Figure 5-3.  Motorcycle Control Head Cabling (3075217A01)When determining its location, position the control head so that it is clearly visible and within easy reach of the motorcycle operator.!C a u t i o nDraftababDraftDrafraraDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDttttttttttftftftfftftftftftfftfttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttftttttttftttttfttttfttftttftfttftttftttftfttttftftttftfttttttftftftftftftftttftftftftftftftftftffftftftttttttttttttttttttttttftttttttfttttftttttfttftttfttfttfaftaftaftfttfttttfttfttttftfttftttftftftftftfftafafafafafafafafafafafafftfttftftftftttttttttttttftftttttttftfttttttttftftftftttttttfttttttfttttttftafftaftaftaftaftaftaftaftftfttttttaftftfttttttatttttfttttttftfttttttaftftfttttttaftttttftftttttftftfttttaftftfttttafttttfttttftaftfttttftfttttftftftttftttftftftftttftftaftftaftftaaftaftaftaftaftaftraaaafrararaaraarararaararaarararaararaarararaaafafafaaaafffafaffaaaafraftftaaaaaaaaafraaafraafraraafafafafafafraraararararararaftftftftftftftftftftftftttftttftftttttftfttttttttttftfttttttttttttttttttttttttttttttttttfttafafaaararaaaaraafafaaaraafafafafafafrararaaaraafftafafftftaaft
MN003109A01_aa5-8 Motorcycle Radio Installation Installing the Speaker and Control Head5.4.1 Handlebar Installation with Speaker and Control Head Mounted TogetherFigure 5-4 illustrates the combination speaker/control head bracket. This combination bracket is used only when the control head and speaker are to be mounted as a unit. Also illustrated in Figure 5-4 is a handlebar-mounting bracket which may be required if the combination speaker/control-head bracket cannot be easily mounted to the motorcycle. In this case the  handlebar-mounting bracket is mounted to the motorcycle, and the combination bracket is then mounted to the handlebar-mounting bracket.Figure 5-4.  Handlebar Installation with Speaker and Control Head Mounted Together
MN003109A01_aaMotorcycle Radio Installation Installing the Speaker and Control Head 5-9Provision has been made on the combination speaker/control-head bracket for mounting the microphone hang-up clip. If that mounting is desired, the hang-up clip must be attached to the bracket before installing the control head and speaker. See Section 5.6: “Installing the Microphone Hang-Up Clip”  for the hang-up clip procedure. Install the speaker and control head as described below.1. Determine the location where the speaker/control head is to be mounted. Consider how the speaker/control-head bracket may be mounted, and whether or not a handlebar-mounting bracket is needed. Take care to select a location that is not only mechanically convenient, but is located for ease of operation.NOTE: The angle at which the handlebar-mounting bracket or the speaker/control-head bracket is mounted to the motorcycle determines the firing angle of the speaker.2. If the handlebar-mounting bracket is needed, install it first.3. Mount the speaker/control-head bracket, either directly to the motorcycle, or, if used, to the handlebar-mounting bracket, using four stainless-steel machine screws, lock washers, and nuts. 4. Mount the 9-pin D-connector end of the motorcycle control-head cable to the speaker/control head bracket, using two machine screws, flat washers, and nuts. (Cable routing directions appear later in this section.) 5. Mount the speaker on the speaker/control-head bracket, using two machine screws and lock washers. Torque these screws to 20 in-lbs. 6. Attach the control-head cable to the control head and tighten the locking screws on the connector. This connection must be made before you mount the control head in the bracket. (Cable routing directions appear later in this section.) 7. Mount the control head to the bracket, using two machine screws, lock washers, and flat washers. 8. Adjust the control head viewing angle by loosening its mounting screws and rotating the control head to the desired angle. Then, retighten screws to 20 in-lbs torque. This concludes the speaker/control-head installation.5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted TogetherSome motorcycles provide a console for mounting radio equipment. This console is attached to the top of the fuel tank. With the use of a mounting bracket, screws, nuts, and lock washers, the combination speaker/control-head bracket can be mounted to this console. Figure 5-5 illustrates this type of mounting.The console attachment screws must be removed, and the console must be lifted slightly from the fuel tank to gain access in order to attach mounting hardware, and to route cables later.In this installation, the microphone (mic), mic hang-up bracket, and mic extension bracket will interfere with handlebar travel. Installation using this method is the same as in Section 5.4.1: “Handlebar Installation with Speaker and Control Head Mounted Together” .Drafttortoo machino machiection.) ectioner on the speaer on ker/cokee these e thescrews to 20 in-l to -head cable to the contro-head cable to the l nection must be made beection must be mafons apppear later in this sectiear later in ththe bracket, using he bracket, using two mactwangle by longle by loosening its mouosening its mohen, retighten screws to 2en, retighten screws taker anker
MN003109A01_aa5-10 Motorcycle Radio Installation Installing the Speaker and Control HeadFigure 5-5.  Fuel Tank Console Installation with Speaker and Control Head Mounted Togetherf
MN003109A01_aaMotorcycle Radio Installation Installing the Speaker and Control Head 5-115.4.3 Handlebar Installation with Speaker and Control Head Mounted SeparatelyIt may be necessary to use the smaller control head bracket (part number 07-80127N02) and mount the speaker and microphone hang-up clip in another location on the motorcycle.Before installing the control head using the bracket described above, the control-head end of the control-head cable should be temporarily fastened to the control head, and the control head fastened to its bracket. Motorola-supplied spacers and the mic-cable bracket are required to mount the control head to the handlebar. This mic-cable bracket has holes to mount the microphone-cable connector.Follow these procedures when mounting the smaller control-head bracket:1. Determine the location at which the control head is to be mounted. Take care to choose a location that is not only mechanically convenient, but is located for ease of operation.2. Securely mount the Motorola-supplied spacers, mic-cable bracket, and small control-head bracket to the handlebars.3. Mount the 9-pin D-connector end of the motorcycle control-head cable to the mic-cable bracket, using two machine screws, flat washers, and nuts. (Cable routing directions appear later in this section.)4. Attach the control-head end of the cable to the control head and tighten the locking screws on the connector.5. Mount the control head to the small control-head bracket, at the proper viewing angle, using two wing screws. Tighten firmly. This concludes the control-head installation.end end ofofhead to the small chead to the smaws. Tighten firmly. This s. Tighten firmly. Tco
MN003109A01_aa5-12 Motorcycle Radio Installation Installing the Speaker and Control HeadFigure 5-6.  Handlebar Installation with Speaker and Control Head Mounted Separately5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted SeparatelyThe control head may be mounted to the fuel tank console using the smaller control-head bracket and spacers/hardware. In this configuration, the microphone cable connector may be attached directly to the console, eliminating the need for a custom bracket.
MN003109A01_aaMotorcycle Radio Installation Installing the Speaker and Control Head 5-13Figure 5-7.  Fuel Tank Console Installation with Speaker and Control Head Mounted SeparatelyInstallation is the same as detailed in Section 5.4.2: “Fuel Tank Console Installation with Speaker and Control Head Mounted Together”  and Section 5.4.3: “Handlebar Installation with Speaker and Control Head Mounted Separately” .
MN003109A01_aa5-14 Motorcycle Radio Installation Installing the Speaker5.5 Installing the SpeakerNOTE: To disable the internal speaker of the O2 Control Head, please refer to Section 2.5.1: “Internal Speaker Disassembly” .Use the following procedure when the speaker is mounted separate from the control head. The speaker bracket supplied with the speaker may be used alone if a suitable location can be found, or if necessary, a customer-supplied bracket may be fabricated for mounting the speaker.1. Determine the location in which the speaker is to be mounted and whether there is a requirement for a customer-supplied bracket.2. Fabricate a bracket if required. Use the Motorola-supplied speaker bracket as a template for drilling mounting holes. Also drill holes in the fabricated bracket for mounting to the motorcycle.3. Mount the fabricated bracket to the motorcycle chassis.4. Mount the Motorola-supplied bracket to the fabricated bracket using two machine screws, flat washers, lock washers, and nuts.5. Mount the speaker to the speaker bracket using two wing screws. Directions for speaker cable routing appear later in this section. Speaker mounting is now complete.5.6 Installing the Microphone Hang-Up ClipInstall the hang-up clip either on the supplied microphone extension bracket or on the side of the speaker/control head bracket. Both methods are shown in Figure 5-4. Determine the mounting location and install as described in the following paragraphs.NOTE: Wherever the hang-up clip is mounted, it must be DC grounded for proper operation. After mounting the clip, be sure there is electrical continuity between the clip and the motorcycle chassis.5.6.1 Extension Bracket MountingUsing this method, you can mount the clip so that it faces the operator. 1. Attach the bracket to the speaker/control-head bracket using two machine screws, four lock washers, and two nuts as shown in Figure 5-4.2. Torque nuts to 20 in-lbs torque.3. Fasten the hang-up clip to the extension bracket using two machine screws, lock washers, and nuts as shown in Figure 5-4.4. Torque nuts to 20 in-lbs torque.5.6.2 Speaker/Control Head Bracket Side MountingAttach the hang-up clip to the left side of the speaker/control-head bracket using two machine screws, lock washers, and nuts as shown in Figure 5-4. Torque nuts to 20 in-lbs. torque.Drafteain this sin this ophone Hangophone Hather on the supplied mither on the suppliecroket. Both methods are showet. Both methods aed in the following paragraed in the following pp is mounted, it must be Dmounted, it musere is electrical ere is electriccontinuity bconit faces the operat faces the opera bracket uacke
MN003109A01_aaMotorcycle Radio Installation Installing Antenna Base, Cables and Multiplexer 5-155.6.3 Other Hang-Up Clip MountingTo mount the microphone hang-up clip in another location, a customer-supplied bracket may be used. Suggested locations include the handlebars, fuel-tank console, or any location which provides easy access to the microphone without blocking controls and indicators and without interfering with motorcycle handling. See Figure 5-5, Figure 5-6, and Figure 5-7 for alternative microphone hang-up clip mounting methods.1. Fabricate a bracket, then secure it to the motorcycle.2. Use two machine screws, lock washers, and nuts to secure the hang-up clip to the customer-supplied bracket. Ensure that the microphone clip is DC grounded to the motorcycle chassis (a grounding lug and strap are provided in the hang-up clip kit for this purpose) – this is essential for proper radio operation.5.7 Installing Antenna Base, Cables and MultiplexerNOTE: Antenna hole placement and cable routing in 700/800, VHF and UHF antenna manuals are not applicable for the APX Series.  The GPS antenna assembly must be done after the removal of the metal liner but before reinstalling the APX Series liner.Figure 5-8.  Antenna Band Identification1. Open the top cover of the weather-resistant enclosure.2. Uninstall the metal liner that is shipped attached to the weather-resistant enclosure. This liner has one depressed area at the top of the enclosure liner just toward the rear of the enclosure. This metal liner is not used with APX Series products.3. Place the metal liner with two round, depressed areas toward the enclosure hinge and 1 inch hole near the front of the housing, inside the top cover, and align the six slots in the metal liner with the screw holes in the top housing.4. The metal liner of the enclosure’s top cover acts as a ground plane for the antenna.5. Locate the two round, depressed areas about 3 inches in diameter in the metal liner near the enclosure hinge. Referring to Figure 5-9, these areas are either VHF or UHF depending on the antenna port locations. For the GPS antenna, use the 1 inch hole near the front of the housing near the lock.GPSLMR all-band PortWi-FiDraftembly membly mX Series liner.X Series liner.DraftraftraftDraDDrrraDraararaaafaffftfffftftftaftaftfffaftaftaftaftftffffaftaftaftftftftaaftftfftftftftftftftfftffftffftfffffffaftaftaftaftaftftfttfttfttfttftftftftftfffffffffffffffafttttttttftftftrarfrarfrarrraraftDraDraDrDrDraaftftftftftafafaftfftaftaftaftftftftftftftftftftftftftftftftftftftftftftftftftftfttftttftftftfttftfttftttfttfttftftftfttaaaaaaaaarafafraafrafaraaaaararaaaarrarrarrrararrarrarrrarrarrrarararrararararararararararaftftftfttftftafaaftaftafaaaaftftfttraraaafrarararararffffffftftftftftftftftftftftftftfttftftftfttttttftftftftfftfaftffaftfaftfaffftfffftftftftfffffffftffffftftftftftftftftftftfrarararararararaaaaaaaaafffffaftfaftaftaftffaftaftaftaaDrDrDraftftftftaffaftaftaftaftftftaaftfffaftaftfaftfrrrararaaraaaaarraaarraaaaarararaararrrarararrrraaarrararrraaaararaaaraaraaraarararararararaararararaaaararaaaaararaaararaaararaaraaraaraarararaaraaarrarraaraararaaaraararaaaraaraarrararraaaaraaraaaaaaaaaaaaaarararararararrararararararrararaaraaararaaaraaaraaaraaraaararaaaaaaaaararaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaftftftftftft
MN003109A01_aa5-16 Motorcycle Radio Installation Installing Antenna Base, Cables and MultiplexerFigure 5-9.  Antenna Port Locations6. These holes in the metal liner is used as a template to mark the position of the hole(s) to be drilled at the top cover. Follow the below guidelines for the various options.7. Remove the metal liner from the top cover.8. For LMR all-band antenna, use the Motorola RPX-4378A Hole-Cutting Saw or equivalent, and carefully drill a 3/4-inch hole at the marked location from the inside of the cover until the saw bottoms out. For the GPS/WiFi carefully drill a 1 1/16-inch hole at the marked location from the inside of the cover until the saw bottoms out. The saw should clean a neat circle to assure good contact between the antenna and the housing.IMPORTANT: For proper seating of the antennas, deburr and scrape any foreign matter from both sides of the hole, being careful not to mar the finish of the shell.9. Clean the mounting surface around the hole to remove dirt and wax.10. Refer to the Motorcycle GPS Instruction Manual for further installation instruction for the GPS. GPS must be mounted before the APX metal liner is installed.11. Reinstall the APX metal liner with the cable clamps provided in the weather-resistant housing. 12. Attach the 700/800, VHF or UHF antenna base per Antenna Installation Manual.IMPORTANT: Antenna Placement and Cable Routing in the Antenna Installation Manual is not applicable for the APX series.Top Cover for APX Radios700/800AntennaUHFAntennaGPS/Wi-FiVHFAntennaDraft.  Antenna Port Locationstenna Port Locationsas a template to mark thea template to mark tguidelines for the vaguidelines for the vX-437X-43DrDrDrDrDrDrDrDDDDDDDDDDrDD
MN003109A01_aaMotorcycle Radio Installation Installing Antenna Base, Cables and Multiplexer 5-1713. Route the coaxial cable for the 700/800, VHF or UHF antenna(s) through the cable clamps per Figure 5-11 for VHF hole, Figure 5-12 for 700/800 hole and Figure 5-13 for UHF hole.14. After routing cable, allow enough of the cable to reach the radio’s antenna connector and cut off any excess length of the cable.15. Install the connector per Antenna Installation Manual.Figure 5-10.  Routing the GPS/Wi-Fi CableBe sure to observe the correct routing of the antenna cable. Failure to do so can damage the cable.!C a u t i o nCable routes underneath radio mounting plate and connects to multiplexer mounted underneath radio on the radio mounting plate Cable Clamps need to be included and routing to be through cable clampsGPS/Wi-Fi cables connect to radio directlyNOTE: Do not cut the antenna cableaftftftftftftftftftttftDraftDraftDDDDrarafrararaDDDrararaDDDDDDraDDraafDraDDDDDDDDDDDfDrDrDDrftrrararaafafaffrrarararafafafafffffraftftaftaftaaftaftaftftaftftftftaftftaftftDrafafafaft
MN003109A01_aa5-18 Motorcycle Radio Installation Installing Antenna Base, Cables and MultiplexerFigure 5-11.  Routing the VHF Antenna CableFigure 5-12.  Routing the 700/800 Antenna CableCable Clamps need to be included and routing to be through cable clampsCable routes underneath radio mounting plate and connects to multiplexer mounted underneath radio on the radio mounting plate NOTE: Do not cut the antenna cableCable Clamps need to be included and routing to be through cable clampsCable routes underneath radio mounting plate and connects to multiplexer mounted underneath radio on the radio mounting plate NOTE: Do not cut the antenna cableDraRouting the VHF Antenna CRouting the VHF AnDraDraraDraDrDDDDDDDrrDrDrDDDDDDDrrrDrDrDDrraftaftaafaaafafftftftftftaftftaftftaftftaftftaftafaftaaftaftaftaftafaftaftftftftftftftftftftftftftftftftftaftaftftaftaftftftftft
MN003109A01_aaMotorcycle Radio Installation Installing Antenna Base, Cables and Multiplexer 5-19Figure 5-13.  Routing the UHF Antenna CableFigure 5-14.  Multiplexer and Trunnion MountingCable Clamps need to be included and routing to be through cable clampsCable routes underneath radio mounting plate and connects to multiplexer mounted underneath radio on the radio mounting plate NOTE: Do not cut the antenna cable  Routing the UHF Antenn Routing the UHF DraDraraDraDrDDDDDDDDDDDrDDDDDDDrDrDrDraft
MN003109A01_aa5-20 Motorcycle Radio Installation Installing Antenna Base, Cables and MultiplexerFigure 5-15.  Cable RoutingFigure 5-16.  Cable from Radio to MultiplexerNOTE: Radio has to be mounted with the TIB facing the front of the enclosureNOTE: Do not cut the antenna cablerafte 5-15.  Cable Routing5.  Cable RouDraft
MN003109A01_aaMotorcycle Radio Installation Installing the Antenna 5-215.8 Installing the AntennaIMPORTANT: Antenna Placement and Cable Routing as described inside the Antenna Installation Manual is not applicable for the APX radio series. Refer to information listed below.• Connect the appropriate antenna connectors to the antenna receptacles on the radio. Tighten the coupling until fully engaged.5.9 Cable RoutingFive cables must be installed to interconnect the components of the radio system as shown in Figure 5-17. The antenna cable is routed away from the other cables inside the enclosure’s hinged cover (see Section 5.7). The four remaining cables, routed along the motorcycle frame, are described in the following paragraphs.NOTE: Antenna Hole Placement and Cable Routing information in the Antenna Installation Manual is not applicable to the APX series.  Removal of the fuel tank and seat from the motorcycle will facilitate routing the cables along the frame. Motorcycles with consoles attached to fuel tanks require routing cables between console and fuel tank. In this case the tank is not removed.Figure 5-17.  Cable Routing1. Speaker Cable – runs from the speaker to the accessory-cable connector inside the weather-resistant enclosure.CONTROL HEADCABLESPEAKER/CONTROL HEADSPEAKERCABLEMICROPHONEIGNITIONCABLECHASSIS GROUNDFUSED POWERCABLESPEAKERCABLEANTENNACABLEACCESSORYCABLEPOWERCABLECONTROL HEADCABLEBATTERYFUSEBLOCKandanes with cones with conk. In this nk. In this casecasDraftSPEATROL ERBLECONTROL HEACABLERYtrD
MN003109A01_aa5-22 Motorcycle Radio Installation Cable Routing2. Control Cable – runs from the rear of the control head to the front of the transceiver inside the enclosure.3. Ignition Sense (Red) Wire Portion of Accessory Cable – runs from the ignition sense fuse terminal of the fuse box to the rear area inside the enclosure. The lug for attaching the ignition sense wire is contained on the accessory cable.4. Power Cable – The red, unterminated end runs from the positive terminal of the battery to the power connector that plugs in the rear of the transceiver. Lugs for attaching the red and black leads are contained in the motorcycle power-cable kit. The black, unterminated end runs from a suitable motorcycle chassis ground to the power connector. DO NOT connect the black lead directly to the negative battery post.You may route the cables in any order. As you route each cable, temporarily fasten it at both ends. When all cables have been run, permanently fasten the cables with appropriate cable tie wraps. Observe the following during routing and hook-up:1. Route the cables so that none interfere with motorcycle operation.2. Fasten the cables with supplied nylon tie wraps. The wraps should be firmly installed at frequent intervals along the cable length in such a manner that motorcycle vibration will not cause metal fatigue and subsequent breakage of the cable wires. 3. Take care to position cables away from parts of the motorcycle that get hot.Bundle excess cable length inside the weather-resistant enclosure as discussed later in Section 5.11: “Transceiver, Cabling and Multiplexer Installation” . The fifth cable is the microphone with coiled cord. Plug the 9-pin D-connector end of the coiled cord into its mating connector, which was attached near the control head discussed in an earlier paragraph. Tighten the coiled-cord-retention screws. Insert the S-hook strain relief (terminated to the coiled cord) into the hole in the mounting bracket. Slide the microphone into the microphone hang-up bracket.Draftubsequubsequn cables away fromn cables away frogth inside the weather-gth inside the weatresanand Multiplexer Installatiod Multiplexer Insne with coiled cord. e with coiled cord.Plug thas attached near the contattached near thetention screws. Intention screws. Insert the sg bracket. Slide the micropracket. Slide the microp
MN003109A01_aaMotorcycle Radio Installation Installing the Weather-Resistant Enclosure 5-235.10 Installing the Weather-Resistant EnclosureFigure 5-18.  Weather-Resistant Enclosure Installation1. Remove the radio-mounting plate by removing four screws, lock washers, and flat washers.2. The weather-resistant enclosure is mounted to the universal mounting plate using shock mounts. Assemble the shock-mount components exactly as shown in Figure 5-18. Be sure to install ground straps between the shock-mount and the transceiver trunnion mount, and install one 7-1/2-inch ground strap between the right rear mount and the enclosure lid’s antenna ground plane 0 (shown in Figure 5-18 and in Figure 5-20).3. The order of assembly is important to ensure proper shock mount operation. All components are supplied with the mounting kit. The five 7- 1/2-inch straps are used on the rear and front shock mounts – four from shock mount to trunnion, and one from the shock mount to the lid’s antenna ground plane. NOTE: Grounding through the power-supply cable is NOT sufficient. Whether the radio transceiver is mounted to a carrier or the chassis itself, the transceiver MUST be properly grounded to the motorcycle chassis. The ground strap supplied with the installation kit may have to be used to ensure a good RF ground path from the radio transceiver to the motorcycle chassis.   4. Install the 3-foot ground strap on one of the front shock mounts. Route it through the cable-routing hole and connect the other end to the motorcycle frame (see Figure 5-18).DO NOT connect the ground strap directly to the negative battery post.71723 4856TO MOTORCYCLECHASSIS GROUNDItem No. Description Item No. Description1 Universal Mounting Plate 5 Flat Rubber Washer2 Machine Screw 6 Shouldered Rubber Washer3 Lockwasher 7 7-1/2-inch Ground Strap4 Flat Washer 8 Ground Strap!W A R N I N G!Draft8.  Weather-Resistant Enc Weather-Resisng plate by removing g plate by removinfoursure is mounted is mounted to the univto the univount untcomponents exactly amponents exactly shock-mount and the transshock-mount and the traetween the right rear motween the right rearre 5-185-18 and in d in FiguFige proper sprope1/2-1/2-inrDDDDr
MN003109A01_aa5-24 Motorcycle Radio Installation Transceiver, Cabling and Multiplexer Installation5. The diagram of the shock mount is shown loosely assembled. After the hex screws are tightened, the rubber washers are compressed to fasten the weather- resistant enclosure securely to the universal mounting plate.6. Figure 5-20 is an exploded view of the enclosure; it shows details that will help to understand how the enclosure is mounted. After the enclosure is completely mounted, check for proper ground connection–continuity between the antenna ground plane and the motorcycle frame.5.11 Transceiver,  Cabling and Multiplexer InstallationAfter the weather-resistant enclosure has been installed, the radio chassis (transceiver) is installed in the enclosure and then appropriate cables are connected. However, before the transceiver can be installed, the cabling must be properly positioned in the enclosure. 5.11.1 Installing Cabling in the Enclosure Position the cabling in the weather-resistant enclosure as follows:1. Run the speaker, power, control-head, and ignition sense cables into the enclosure.2. Lay the excess cable length between the radio mounting bosses in an S configuration as shown in Figure 5-19. Do not coil any excess cable. Use the supplied tie wraps to bundle cable as shown.NOTE: If the extra cable length is not sufficient to match the illustrated cable routing, then match the illustration as closely as possible.3. Connect the speaker cable to the accessory cable connector.NOTE: The accessory-cable emergency connector is shipped with a shorting plug installed. The headset connector is also shipped with a shorting plug installed. The plugs must remain in if an emergency switch and/or headset is not used. If an emergency switch and/or headset is used, remove the shorting plug(s) and discard.4. Install the mounting plate in position on top of the cables installed above. Take care not to damage or pinch the cables when securing the mounting plate in position.NOTE: At this point, the control-head cable plug should be located at the forward end of the enclosure, and the power-cable, speaker-cable, and accessory-cable plugs should be located at the rear of the enclosure.bebenot coil not coilength is not ength sufficient ficisely as possible.sely as possible.cable to cable to the accessory cabthe accessoergency connector is shippncy connector hipped with a shorting ipped with a shortinplugeadset is not used.set is not used If an emn em and discard.and discard.n top of the cables installeop of the cables instng the mounting platthe mounting plauld be locatbe loand aand
MN003109A01_aaMotorcycle Radio Installation Transceiver, Cabling and Multiplexer Installation 5-25Figure 5-19.  Installing Cables5.11.2 Installing the TransceiverInstall the transceiver in the weather-resistant enclosure as follows (see Figure 5-20).NOTE: For new or existing installations, use only the APX mobile trunnion (kit number: HLN7002_).1. Install the mounting trunnion and loose ends of the four ground straps to the radio-mounting plate, using four screws, flat washers, and external-tooth lock washers (see Figure 5-20). The ground straps must be sandwiched between the flat washers and lock washers. The lock washer must be against the trunnion. The flat washer must be under the screw head.2. Attach the transceiver to the mounting trunnion and secure with the two screws provided.3. Connect the control cable to the front of the transceiver. Ensure the control-cable connector screws are tightened.4. Attach the accessory connector to the transceiver. Plug in the power connector.5. Install the grommet around the cables and push the grommet into the cable-routing hole of the weather-resistant enclosure.ACCESSORYCABLETRANSCEIVERPOWER CABLEACCESSORY CABLEEMERGENCY ANDEXTERNAL ALARMCONNETORACCESSORYCABLE HEADSETCONNECTORHEADSETSPORTING PLUGEMERGENCYCABLE SHORTINGPLUGIGNITION SENSE(ACC)CONTROL HEADGROUND (BLACK)CONTROL HEADPOWER FUSECONTROL CABLE(CAN)CONTROL HEADPOWER (RED)Draft19.  Installing Cables19.  Installing Cablescclosure as follolosure as e APX APXfDraDrDrDrDrDraDDDDDrDDDDDrDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDCONTROL HCONPOWER FUSPOWROL HEADOL (RED)D)aDraD
MN003109A01_aa5-26 Motorcycle Radio Installation Transceiver, Cabling and Multiplexer InstallationFigure 5-20.  Installing the Transceiver   1111015736812134291716141826DraftDaftaftaftaftaftftaftaftaftafaftaftaftftftftftftftftftftftfttffaftafaftaftDrafraraafffffDDrDDDrrarDrDrDrDrDrDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD
MN003109A01_aaMotorcycle Radio Installation Installing the Emergency Switch Option 5-275.12 Installing the Emergency Switch OptionUse the two-conductor, green/black cable which has as one end terminated with two contacts (part number 3080221P02) and which is supplied with this W688 Motorcycle Emergency Push Button. Disconnect the emergency switch shorting plug from the accessory cable. Replace the shorting wire of the shorting plug with the terminated end of the green/black emergency cable. Reconnect the plug to the accessory cable.5.13 Installing the External Alarm Relay OptionThe motorcycle radio is offered with only one optional relay connection. If both horn and lights are required, wire a second relay coil parallel to the first relay. Use the two-conductor green/black cable which has one end terminated with two contacts (part number 3080221P02) and which is supplied with this W116 Motorcycle Alarm Relay Option. Insert the contacts into positions 3 and 4 of the emergency shorting plug of the accessory cable. Refer to Figure 5-26.5.14 Installing the Headset AccessoryA six-position connector on the accessory cable has been made available for connecting a headset accessory. Headset manufacturers should be consulted for compatibility with the motorcycle radio prior to purchase and installation of the headset. To install, disconnect the headset shorting plug. Remove the headset shorting wire from the headset shorting plug. Terminate the contacts provided to the applicable wires of the headset cable. Insert the terminated wires into the headset shorting plug per the contact positions illustrated in the typical headset schematic found in this manual. Reconnect the terminated headset shorting plug to the accessory cable.When upgrading from an APX mobile radio, the existing headset cable HLN6890 requires these two pins to be swapped (see Figure 5-21). The other motorcycle headset cable with this pin change already performed is called cable 3080010R04.Table 5-1.  Transceiver Installation Parts ListItem No. Description Item No. Description1Lock washer 10 Ground shield plane2Flat washer (8 used) 11 Top cover3Screw 12 Gasket4Screw 13 Hinge5Grommet 14 Enclosure mounts6Screw 15 Transceiver7Lock catch 16 Screw8Radio mounting plate 17 Trunnion9Bottom housing 18 External tooth lock washer (8 used)Draftmminateinatexternal Alarm Rexternal Alarmoffered with only one optiooffered with only onay coil parallel to the first ray coil parallel to thed with two contacts (part nutwo contactm Relay Option. InseRelay Option. Insert the ccessory cable. Refer to ry cable. RefeFigessoryessoryble hable has been made avs been made onsulted for comnsulted for como install, disstallshortinhor
MN003109A01_aa5-28 Motorcycle Radio InstallationFigure 5-21.  Motorcycle Wiring Harness ReworkJ2, BACK OF RADIO Insert into Pin 22 (Monitor) Remove from Pin 1 (VI P  OU T  1 ) 1 7 8 14 13 20 21 26 Rework for Handlebar HUB operation when upgrading existing cable HLN6890. (Female-Pins) 1 3 5  6 4 2 SPK - VIP OUT 1 AUX_MIC SPK + GND AUX_PTT Draft
MN003109A01_aaMotorcycle Radio Installation Installing the O5 Control Head Sunshield 5-295.15 Installing the O5 Control Head SunshieldInstall the sunshield (part number NNTN7279_) to the O5 control head as follows.1. Assemble the sunshield to the remote mount trunnion as shown in Figure 5-22. The same process can be used for the motorcycle trunnion.Figure 5-22.  Remote Mount Trunnion with Sunshield2. Position the sunshield as shown in Figure 5-23 and remove the Velcro adhesive backing.Figure 5-23.  Position the SunshieldVelcro Adhesive Backinge 5-22.  Remote Mount True 5-22.  Remote Mod as shown in d as shown in Figure 5-23FiguDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDraftrarararararattttttttttaaraftftftttftaraaftftftraraftraftafttttttfttttttttftftftftftftftftftraraafttttaftAdVelcro A
MN003109A01_aa5-30 Motorcycle Radio Installation3. Slide the control head onto the trunnion while aligning the edge of the control head with the edge of the sunshield as shown in Figure 5-24. Make sure the Velcro properly adheres to the control head.Figure 5-24.  Slide the Control Head onto Trunnion4. Position control head as desired and install screws as shown in Figure 5-25.Figure 5-25.  Position Control Head as DesiredDraft5-24.  Slide the Co5-24.  Slide the Cead as desired and instaead as desired andDDDDraftDraftDDDDrrDraDrarararrarararararaaaraaaarafaafafaftafafaafafafafafaaftfftftftftftftfftftaffftfftftfffftfttfDraDraDraaffftftftffftaftfffrftftfftftftftftftfffffftffftftftftftftftaaftftftftftftftftftftftftftftraDraftftftftftfttafafftftftftftftftftftftftftraDrafDrDrDraraafDrarafafftafftftftftttftftftftftftftftftftftftraDrDrDrDrff
MN003109A01_aaMotorcycle Radio Installation Horn/Lights Wiring 5-315.16 Horn/Lights WiringFigure 5-26.  Horn/Lights Wiring Diagram5.17 Emergency Switch WiringFigure 5-27.  Emergency Switch Wiring DiagramMotorcycle products must have pins 1 and 2 connected together to allow the radio to power down. Opening this connection by REMOVING the emergency shorting plug, or pressing the emergency switch, will turn on the radio. Failure to maintain a normally-closed path could drain the vehicle battery if left unchecked.EMERGENCY-equipped radios are capable of TRANSMITTING without warning.!W A R N I N G!DraftWiringWiringWiWi
MN003109A01_aa5-32 Motorcycle Radio Installation Emergency Switch WiringDraft
Chapter 6 Finishing the Installation6.1 Cable Connection6.1.1 O2 Control HeadPerform the following if it has not been previously done:1. Remove the control head from its mounting trunnion. Plug the radio’s CAN cable into the proper location on the back of the control head (see Figure 2-21 and Figure 2-23 in Chapter 2). The connectors “click” when snapped into place. The control head model can have the microphone plugged into the lower left corner of the control head front panel.2. Connect the plug from the speaker lead to the mating connector coming out of the power cable.3. Plug the VIP connector into the correct location on the back of the control head.4. Connect the CAN cable to the proper location on the transceiver.NOTE: Connector-protective covers are provided with the radio. They should be used for added environmental robustness.  Be sure the control head and microphone PTT switches are OFF. Install the 15-amp fuse in the radio power cable fuseholder and the 3- or 4-amp fuse(s) in the ignition sense cable fuseholder(s).  Turn the radio ON at the control head and verify proper operation of all controls and indicators. Radio operation in some installations require turning on the ignition sense. Perform a complete operational check of the radio.  Dress the control and power cables out of the way to prevent damage (pull any excess cable into the trunk area) securing with clamps and tie wraps where necessary.6.1.2 O3 Control HeadPerform the following if it has not been previously done:1. Unplug the CAN coiled cable connector on the Transceiver Interface. Plug in the connector again. A “click” sound should be heard. Ensure location of CAN connector is correct  (i.e. J800L or J800R) on the transceiver interface.Connect the plug from the speaker lead to the mating connector of J2.6.1.3 O5 Control HeadPerform the following if it has not been previously done:1. Remove the control head from its mounting trunnion. Plug the radio's CAN cable into the proper location on the back of the control head (see Figure 2-21 and Figure 2-23 in Chapter 2). The connectors “click” when snapped into place. The control head model can have the microphone plugged into the lower left corner of the control head front panel.2. Connect the plug from the speaker lead to the mating connector coming out of the power cable.Draftto tto e to the pe to the ptive covers are prtive covers are robustness.robusol head and microphone PTol head and microphe fuseholder and the 3- or older and tol head and verify proper ohead and verify proper opptions require turning on thetions require turning on thadio.dio.the way to pthe way td tie wrtie w
MN003109A01_aa6-2 Finishing the Installation Cable Connection3. Plug the VIP connector into the correct location on the back of the control head.4. Connect the CAN cable to the proper location on the transceiver.6.1.4 O7 Control HeadPerform the following if it has not been previously done:1. Remove the control head from its mounting trunnion. Plug the radio's CAN cable into the proper location on the back of the control head (see Figure 2-21 and Figure 2-23 in Chapter 2). The connectors “click” when snapped into place. The control head model can have the microphone plugged into the lower left corner of the control head front panel.2. Connect the plug from the speaker lead to the mating connector coming out of the power cable.3. Plug the VIP connector into the correct location on the back of the control head.4. Connect the CAN cable to the proper location on the transceiver.6.1.5 O9 Control HeadPerform the following if it has not been previously done:1. Remove the control head from its mounting trunnion. Plug the radio's CAN cable into the proper location on the back of the control head (see Figure 2-22 and Figure 2-23 in Chapter 2). The connectors “click” when snapped into place. The control head model can have the microphone plugged into the MMP connection on the control head back panel.2. Connect the plug from the speaker lead to the mating connector coming out of the power cable.3. Plug the VIP connector into the correct location on the back of the control head.4. Connect the CAN cable to the proper location on the transceiver.Draftbeen been ad from its moad from its me back of the contre back of the coonnectors “click” when sonnectors “click” wone plugged into the MMP ne plugged into tm the speaker lead to the mthe speaker lead tothe correct lohe correct location on thecation roper location on the transer location on the trans
MN003109A01_aaFinishing the Installation Dust Cover Installation 6-36.2 Dust Cover InstallationTo help protect and ensure debris does not effect or damage your unused connectors, please use the provided dust covers. Refer to Figure 6-1 to determine which cover is for which connector.Figure 6-1.  Dust Cover Installation LocationsNOTE: Parts B and E require inserting then turning approximately 1/3 turn using a coin as a tool until it contacts the stop.  Part C shall be installed onto DB25 accessory cable assembly when the corresponding cable assembly connection is not in use.  Table 6-1 Dust Cover Kit NumberKit Number DescriptionKT000245A01 Dash MountKT000246A01 Remote MountA: 1515047C01 B: 1515048C01 C: 7575262A01 D:SL000319A01  E: 1515327H02Control HeadAPX 8500 Rear (with no TIB)BCAEAControl Head (Rear)APX 8500 Rear (with TIB)BADDCDDCDraftDraDraDrDrrararaDDDrDrDrDrDrrarararaDrDrDrDrDrDDDDrDDDDDDDrDrDrDrDDDrDrDrDrDrDDDDDDDDDrDrDrDrDrDrDrDDrDrDrDDrDrDrDrDrDrDrDrDrDDraDDDDDDrDrDDrDrDrDraDrDrrarDrDrDrraDrarararrrrararrarararararrrrrrDrDrDrDrDDrDDrDrDrDrDrDrDrDrDrDrDrDDDrDDrDrDDrDrDrDrDrDrDrDrDrDrDrDrDDrDrDrDrDrDrDraDDrDrDrDrDrDrDrDrDDDDDDrDrDrDDDraDDrDDDraDraDrDDDDDDDDDDDrDrDrDrDrDrDrDrrraDrDrDrDrDrDrDrDrDrDrDrDDrDrDrDrDrDrDrDrDrDDDDDDDDDrDrDrDrDrDrDrDrDrDDDDDDDDDrDDDrDDDDDDDrDDrDDrDrDDrDrDrDrDrDrDrDrDrDrDrDrDrDrDrDrDrDrDrrarraDraDDDrDrDrDrDraDDrDDrDDDrDrDrDrraDrDrraDrDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDraDrarrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrDrrafafafafaaaaafaaaaaaaafafaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaafaaafafafaaafafaaaaaaftftftftBftftft
MN003109A01_aa6-4 Finishing the Installation Dust Cover InstallationDraft
Chapter 7 Best Practices: Installation & TroubleshootingIn this section are Motorola recommended vehicle installation practices that can address or prevent many issues, including:• Radio circuit damage due to over voltage condition• Radio/Accessories "lock up"• Radio/Accessories change state/lock-up when radio PTT is depressed• Radio powers up in the FL 01/90 state (general communication error code)• Radio intermittently resets• Radio loses secure key• Transmit audio distortion on motorcycle radio when engine is running• Keypad buttons become inoperative for motorcycle radios when engine is running• Alternator whine present when transmitting with engine running• Radio/Accessories turn themselves on/off7.1 Check Wiring of Ignition and Radio Ignition Sensing• If it is required to turn the radio on and off via the ignition sense switch, in addition to the control head’s on/off switch, connect the ignition sense lead to the accessory terminal from the ignition switch (usually in the vehicle’s fuse panel under accessory or radio).NOTE: Motorola Solutions recommends protecting or isolating the radio’s ignition sense input from voltage spikes in excess of +/- 40VDC. Such spikes can be hundreds of volts in amplitude and are common in larger vehicles (utility trucks, buses and etc.), especially when the source is common to a solenoid coil. A triggerable oscilloscope is required to determine the existence of such spikes as most voltmeters cannot measure in short duration (< 1 msec). If the condition of the intended ignition sense source is unknown, Motorola Solutions recommends isolating the source from the radio with a relay or the use of a suppression diode wired between the source and ground. Any high current suppression diode (i.e. MR2535) with a breakdown voltage of between 18 and 40 volts will suffice. A suitable diode kit is available from Motorola Solutions parts, kit number HLN6325_.• If it is required to have the radio power up only via the control head’s on/off switch, then connect the ignition sense lead directly to the positive terminal of the battery. This will mean the ignition sense will always be ignored and a re-wiring will be necessary in the future if the operator chooses any ignition sense CPS setting. Draftnonoent when ent when  turn themselves turn themselvof Ignitionof Ignition and Rad anurn the radio on and off viarn the radio on and connect the ignition sense t the ignitiohicle’s fuse panel under accle’s fuse panel unends protecting or isols protecting oratingating40VDC. Such spikes can b0VDC. Such spikes canlity trucks, buses and etc.)lity trucks, buses and etble oscilloscope isble oscilloscope is req rmeasure measure in shorin shorown, Moton, Mof a sf a
MN003109A01_aa7-2 Best Practices: Installation & TroubleshootingCheck Physical Installation of Radio Ground and Radio Accessory Wiring7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring• Take care to scrape away paint on the chassis at the place where the ground connection is to be made, and try to keep the ground lead as short as possible. NOTE: Some vehicles have dedicated ground points. If available, use the ground points for the radio ground connection.• Verify that the A+ lead (red) is connected directly to the positive terminal of the battery and the ground lead (black) is connected to the vehicle’s chassis using as short of a length of wire as is practical.• For vehicles that have other types of electronic equipment installed (lights, flashers, computers siren/PA and etc.), use a separate ground for the mobile radio equipment.• Make sure that the mobile radio antenna is the minimum required distance (three feet) from the mobile radio equipment to prevent radio frequency interference (RFI) from interfering with the radio and/or accessories.NOTE:  If multiple radios/antennas are installed, ensure that the minimum antenna separation requirements are met.• Do not coil up any excess length of the A+ (red) lead. Doing this may cause a large transient voltage to be produced when there is a high current drain (e.g. during transmit). This could cause the radio to reset when the push-to-talk (PTT) is depressed.• For motorcycle mounted radios, make sure that the antenna ground connection is solid. An intermittent ground connection can cause the transmission to be distorted when the motorcycle’s engine is running.• Do not coil up any excessive length of antenna cable, if possible. It may affect the radio’s receive performance.• If an extra length of cable is used to extend the microphone, make sure the added capacitance does not interfere with the operation of the radio.7.3 Improve the Electrical Quality of the Power and Ignition Lines• Use a relay to isolate the vehicle’s ignition switch point (ACC) from the radio’s ignition sense point. Control this relay from the vehicle’s ignition switch point (ACC). Supply a cleaner voltage from the positive terminal of the battery into the relay, which will now be attached to the radio’s ignition sense point. Now the ACC line toggles the relay, instead of directly toggling the radios ignition sense line.• Install a Power Line Filter between the A+ lead and the positive terminal of the battery. This is intended to filter the battery power applied to the transmitter power amplifiers. Pay extra caution to this because the series filter will introduce a negative spike when the radio transmits that may cause problems with radio operation. • For vehicles that use electromechanical relays to control external devices (lights, motors, switch boxes and etc.), these relay circuits should be isolated as best as possible from the mobile radio equipment. Also, diode suppression should be used across the relay contacts to minimize the noise produced by the collapsing magnetic field.• If the ignition sense switch is to be used, make sure that there is not a large voltage drop between the A+ point (usually the positive terminal of the battery) and the ignition sense point. In general, the voltage difference between these two points, should not be greater than 1.5 volts when all accessories/air-conditioner, etc. are turned on. Refer to the Basic Service Manual for specifications for minimum and maximum voltage levels. Typical battery voltage levels are 13.6V +/- 20%.Draftarcess length of thcess length of uced when there is a uced when there io reset when the push-to-o reset when the pnted radios, make sure thanted radios, make nection can cause the nection can cause tranning.g.length of antenna length of antenna cable, ifco extend the microphone, m extend the microphone, e operation of the radio.operation of the radiohe Power he Poweh poinpo
MN003109A01_aaBest Practices: Installation & Troubleshooting Minimize the Effect of Poorly Grounded Antennas 7-37.4 Minimize the Effect of Poorly Grounded Antennas• For vehicles with high power radios that use glass mount antennas, care must be taken to keep the radio and antenna cable as far as possible from the radiating element of the antenna. If a sufficient distance is not maintained, the glass mount antenna’s lack of a proper ground plane may cause the radio’s transmit signal to interfere with itself and cause a reset. To minimize this effect, it may be necessary to install ferrite beads on the antenna cable to protect the radio from this interference.7.5 Jump-Start the VehicleJump-starting a motorcycle can crank 300+ volts through the vehicle’s charging system and these transients can damage electrical equipment.The state of your radio prior to needing a jump-start may be unknown, and the radio may attempt to return to its last state (radio ON), when doing a jump-start. Therefore, Motorola recommends the following steps be taken before jump-starting any vehicle containing a radio.1. Locate the ignition sense line (thin yellow wire or thin red wire, depending on dash mount or remote mount installation) and the main power leads (thick red wire) near the battery positive terminal.NOTE: These lines are fused. In the event these lines are not fused (add the appropriate fuse in line) use whatever tools necessary to physically disconnect the ignition sense and power lines from the battery terminal.  Make sure that the disconnected lines are not in the way of moving motorcycle parts or interfering with the motorcycle operation in any way.2. Open up the fuse holders and remove the fuses out of the kits.3. Re-tighten the fuse holders but without the fuses to insure that ignition sense and power lines do not interfere with moving motorcycle parts.4. Proceed with the jump-start routine as described by your vehicle owner’s manual.5. Once the jump-start process is complete, re-install the fuses into their holders.7.6 Eliminate Noise/Howling from PA Speaker1. Refer to Section 2.1.1 for recommended methods of installation available for the mobile  two-way radio, with accessories placed on or inside the vehicle.2. Refer to Section 2.1.2 for the wiring diagrams for the recommended configurations.3. Refer to the Siren/PA User Manual for further details on lowering the wattage.Do not jump-start vehicle with radio power or ignition sense cables connected. Damage to the radio and/or accessories may result.!C a u t i o nDraftal equial equr to needing a r to needing adio ON), when doindio ON), when dgen before jump-starting aen before jump-starn sense line (thin yellow wn sense line (thin yeation) and the main poweration) and the mainhe event these lines are noe event these linesy to physically o physically disconnect tdisconnect tare not in the way ore not in the wayn any way.n any wayes ous o
MN003109A01_aaNotes7-4 Best Practices: Installation & TroubleshootingDraft
Appendix A Replacement Parts OrderingA.1 Basic Ordering InformationWhen ordering replacement parts or equipment information, the complete identification number should be included. This applies to all components, kits, and chassis. If the component part number is not known, the order should include the number of the chassis or kit of which it is a part, and sufficient description of the desired component to identify it.The ASTRO APX Mobile Radio Basic Service Manual includes complete parts lists and part numbers.Refer to Table of Content for applicable manual numbers.A.2 Motorola Online Service and SupportFor general support, users can access • http://www.motorolasolutions.com/en_us/support.html• http://www.motorolasolutions.com/en_us/contact-us.html• http://www.motorolasolutions.com/en_us/products/two-way-radios/project-25-radios/mobile-radios/apx8500.html• Motorola Online Website: https://businessonline.motorolasolutions.com/To register for online access:• Domestic customers: please call 800-814-0601 (U.S. and Canada).• International customers: please go to https://businessonline.motorolasolutions.com/ and click on “Sign Up Now.”Drs.cs.ctionstions.com/.com/solutions.com/en_solutions.com/etmltmlWebsite: https://busWebsite: https://buinesson
MN003109A01_aaA-2 Replacement Parts Ordering Accessories Aftermarket Division (AAD)•ECATAs a registered user, you have access to the electronic catalogue for purchasing accessories and radios.A.3 Accessories Aftermarket Division (AAD)The Accessories Aftermarket Division is able to provide Motorola Solutions Branded accessories for all your radio needs. Contact Motorola Solutions after you have a KIT number, identified from the Motorola Online website and/or the ECAT catalog. You can contact them at: 800-422-4210.Draftcess to the elss to tectronic cataectronion (AAD)on (AADovide Motorola Svide Motorola Sryou have u hacan coan c
Index IndexAaccessoriesconnector assembly  .......................................4-1, 4-9assembly ......................................................... 4-10disassembly ....................................................... 4-9exploded view  .................................................. 4-10connector pins  ....................................................... 4-8headset ........................................................5-2, 5-27installingdash mount  ........................................................ 4-1horn relay  ........................................................... 4-3light relay  ........................................................... 4-3remote mount  .................................................... 4-9antenna ..................................................................... 5-5cable, see Cables, antennainstalling ..................................................... 2-32, 5-21motorcycle ............................................................. 5-2mounting ............................................................. 2-32site ....................................................................... 2-32Bbase stations  ........................................................... 1-11black lead  ..............................................2-30, 5-22, 5-27Ccables  ................................................5-3, 5-4, 5-5, 5-24accessory  .....................................4-1, 4-2, 5-22, 5-27antenna ............................................................... 2-18battery ................................................................... 4-9connection ......................................................6-1, 7-1diagrams  ...........................................2-22, 5-21, 5-25emergency .......................................................... 5-27excess ................................................................. 5-24ignition ................................................................... 4-9microphone ..................................................5-2, 5-12motorcycle control head  ...............5-1, 5-9, 5-11, 5-22motorcycle control head, installing  ...................... 5-21motorcycle transceiver  ........................................ 5-24power .........................................................2-30, 5-22remote mount  ...................................................... 2-21routing ................................................................. 5-22speaker  ...............................................5-2, 5-14, 5-21configurationsdash mount  ........................................................... 1-6motorcycle ........................................................... 1-11multi control  ......................................................... 1-11remote mount  ........................................................ 1-8control head  ..............................................2-26, 4-6, 4-8cabling ................................................................. 2-21diagrams ....................................................2-22, 2-23multi ..................................................................... 1-11remote mount  ........................................................ 1-8control stations  ........................................................ 1-11Ddash mountaccessories installations  ....................................... 4-1configuration ......................................................... 1-6installation examples  ............................................. 2-2radio dimensions  ..............................1-1, 1-2, 1-3, 1-4trunnion ............................................................... 2-19Eemergency footswitch  ............................................... 4-1emergency pushbutton  ............................................. 4-1emergency switchinstalling .............................................................. 5-27wiring ................................................................... 5-31external alarminstalling .............................................................. 5-27see also Horn relay or Light relayFfootswitch, emergency  .............................................. 4-1Hhorn relay  .........................................4-2, 4-3, 5-27, 5-31Iignitioncable ..................................................................... 4-9wire ..................................................................... 5-22wire, for motorcycle  ............................................... 5-2installationexamples ............................................................... 2-2important hints  ...................................................... 5-4order of  .................................................................. 5-5JJ2 ....................................................................... 4-7, 4-8Lleadsblack  .................................................. 2-30, 5-22, 5-27light relay  .........................................4-2, 4-3, 5-27, 5-31locking kit, installing  ................................................ 2-29Mmicrophone ........................................................ 5-2, 5-4hang-up clip, installing  ........................................ 5-14hang-up clip, standard  ................. 2-38, 5-5, 5-9, 5-11mounting ............................................................... 5-4motorcycleantenna ................................................................. 5-2configuration ........................................................1-11control head cable  ................................................. 5-1Draft......................................................... 2-3................. 2-..................... 1-11..................... 1-112-30, 5-22, 5-27-30, 5-22, 5-275-242477Hhorn reIIignitionignitioncable .................cable ................wire .......................wire .....................wire, for motorcycle e, for motorcyclinstallationinstallatiexamples .........examples ....portant hintstant hr of  ....of .
Index-2MN003109A01display unit  ............................................................ 5-1external speaker  .................................................... 5-2headset ................................................................. 5-2ignition wire  ........................................................... 5-2installation ............................................................. 5-3antenna ............................................................ 5-21cables .............................................................. 5-21cabling ............................................................. 5-24control head  ....................................................... 5-7emergency switch  ...................................5-27, 5-31external alarm  .................................................. 5-27fuel tank console  ..............................5-9, 5-10, 5-12handlebar .................................................. 5-8, 5-11headset ............................................................ 5-27horn/lights wiring  .............................................. 5-31microphone hang-up clip  ................................. 5-14speaker ..................................................... 5-7, 5-14transceiver .............................................. 5-24, 5-26universal mounting plate  .................................... 5-6weather-resistant enclosure  ............................. 5-23microphone ........................................................... 5-2transceiver ............................................................. 5-1mounting configurations  .......................................... 2-18dash ............................................................. 1-6, 2-19motorcycle ........................................................... 1-11multi control  ......................................................... 1-11remote ..........................................................1-8, 2-21mounting plate, universal  ............................5-1, 5-3, 5-5installing ................................................................ 5-6mounting, antennarestrictions ........................................................... 2-32roof top  ................................................................ 2-32trunk lid  ................................................................ 2-32multi controlconfiguration ........................................................ 1-11Oordering replacement parts  .......................................A-1Pparts, ordering replacement  ......................................A-1pinSW B+  .....................................................4-3, 4-7, 4-8VIP in  ..................................................................... 4-8VIP out  ............................................................ 4-3, 4-7pushbutton, emergency  ............................................ 4-1Rrelayshorn  ..............................................4-2, 4-3, 5-27, 5-31light  ...............................................4-2, 4-3, 5-27, 5-31remote mountaccessory installations  .......................................... 4-9cabling ................................................................. 2-21configuration .......................................................... 1-8control cable installation  ...................................... 2-26installation examples  ............................................. 2-2trunnion ............................................................... 2-21replacement parts, ordering  ......................................A-1Sspeaker ..................................................................... 5-5cable, see Cables, speakerexternal ................................................................. 5-2fuel tank console installation  ............... 5-9, 5-10, 5-12handlebar installation  .......................... 5-8, 5-11, 5-12installing ................................................ 5-7, 5-9, 5-14mounting ............................................................. 2-35Ttrunnion ................................................................... 2-22bracket for speaker  ............................................. 2-35dash mount  ......................................................... 2-19diagrams ............................................................. 2-22locking kit  ............................................................ 2-29motorcycle installation  ......................................... 5-25mounting bracket  ................................................ 2-19remote mount  ............................................... 1-8, 2-21transmission hump mounting  .............................. 2-20Uuniversal mounting plate  ............................. 5-1, 5-3, 5-5installing ................................................................ 5-6VVIPconnector ....................................................... 4-2, 6-2input connections  .................................................. 4-8output connections  ................................................ 4-7Wwiring diagrams  ........................................................ 2-3Draft.......................................1-6, 2-.........1-6, 2-..................... 1-11..................... 1-1........................ 1-11........................ 1-1.................... 1-8, 2-21.................... 1-8, 2-2................5-1, 5-3, 5-5.....5-1, 5-3, 5....................... 5-6....................... 5-6............. 2-32.... 2-3......... 2-32............ 2-32..... 2-32-1111VVVIPVIPconnector ....onneinput connectionsinput connectionoutput connections output connectionWWg diagrams agra
Glossary GlossaryThis glossary contains an alphabetical listing of terms and their definitions that are applicable to the ASTRO radio.Term Definitionband Frequencies allowed for a specific purpose.CPS See Customer Programming Software.Customer Programming SoftwareSoftware with a graphical user interface containing the feature set of an ASTRO radio. default A pre-defined set of parameters.D.E.K Direct Entry Keyboard.digital Refers to data that is stored or transmitted as a sequence of discrete symbols from a finite set; most commonly this means binary data represented using electronic or electromagnetic signals.FCC Federal Communications Commission.firmware Code executed by an embedded processor such as the Host or DSP in a subscriber radio. This type of code is typically resident in non-volatile memory and as such is more difficult to change than code executed from RAM.frequency Number of times a complete electromagnetic-wave cycle occurs in a fixed unit of time (usually one second).GLONASS GLObalnaya NAvigatsionnaya Sputnikovaya Sistema: The Russian Global Navigation satellite system, consisting of at least 24 operational satellites which fly in medium Earth orbit at an altitude of approximately 19,130 km. Each satellite circles the Earth slightly faster than twice a day. GLONASS provides Time and Location to anywhere on Earth, where there is an unobstructed line of sight to four or more GPS satellites. A GLONASS receiver triangulates its position using these satellites.GNSS Global Navigation Satellite System: Standard generic term for satellite navigation systems that provide geo-spatial positioning with global coverage. This term includes GPS, GLONASS, Galileo, Beidou and other regional systems. GNSS is a term used worldwide The advantage to having access to multiple satellites is accuracy, redundancy and availability at all times.Draftned setned sect Entry Keyboardct Entry Keyboaefers to data that is storefers to data that bols from a finite set; mobols from a finite sented using electronic ented using electrormmunications Commissmmunications Coby an embedded procesan embedded proces. This type of code This type of codeis typs tyis more difficult to chais more difficult to che electromectrsecoeco
MN003109A01_aaGlossary-2GPS Global Positioning System: U.S.A.’s Satellite based radio navigation system developed by the U.S. Department of Defense and operated by the U.S. Air Force, which consists of at least 24 operational satellites which fly in medium Earth orbit at an altitude of approximately 20,180 km. Each satellite circles the Earth twice a day. GPS provides Time and Location to anywhere on Earth, where there is an unobstructed line of sight to four or more GPS satellites. A GPS receiver triangulates its position using these satellites.kHz See kilohertz.kilohertz One thousand cycles per second. Used especially as a radio-frequency unit.MCU See microcontroller unit.MHz See Megahertz.Megahertz One million cycles per second. Used especially as a radio-frequency unit. microcontroller unit Also written as μC. A microprocessor that contains RAM and ROM components, as well as communications and programming components and peripherals.PA Power amplifier.paging One-way communication that alerts the receiver to retrieve a message.PTT See Push-to-Talk.Publication Manual RevisionA publication that provides supplemental information for its parentpublication before it is revised and reissued.Push-to-Talk The switch or button that causes the radio to transmit when pressed. When the PTT switch or button is released, the unit returns to standby or receive operation.radio frequency The portion of the electromagnetic spectrum between audio sound and infrared light (approximately 10 kHz to 10 GHz).receiver Electronic device that amplifies RF signals. A receiver separates the audio signal from the RF carrier, amplifies it, and converts it back to the original sound waves.registers Short-term data-storage circuits within the microcontroller unit or programmable logic IC.RESET Reset line: an input to the microcontroller that restarts execution.RF See radio frequency.RX Receive.Term DefinitionDraftertz.ertz.lion cycles per slion cycles pewritten as μC. A microproritten as μC. A micnts, as well as communints, as well as comrals.ation that alerts the receation that alerts the recpplementalemennd reisd re
MN003109A01_aaGlossary-3signal An electrically transmitted electromagnetic wave.software Computer programs, procedures, rules, documentation, and data pertaining to the operation of a system.time-out timer A timer that limits the length of a transmission.TOT See time-out timer.transceiver Transmitter-receiver. A device that both transmits and receives analog or digital signals. Also abbreviated as XCVR.transmitter Electronic equipment that generates and amplifies an RF carrier signal, modulates the signal, and then radiates it into space.Triangulation A method of determining the relative positions of points in space by measuring the distances, and sometimes angles, between those points and other reference points whose positions are known. Triangulation involves the use of trigonometry. It is commonly used in the navigation of vehicles, aircraft and boats, and is the method used in the Global Positioning System, in which the reference points are satellites.TX Transmit.UHF Ultra-High Frequency.Universal Serial Bus An external bus standard that supports data transfer rates of 12 Mbps.USB See Universal Serial Bus.VHF Very-High Frequency.Waypoint Geographic Coordinates of a specific location. It can also be an Intermediate point on a route or line of travel.Wi-Fi Wireless Data Transmission protocol 802.11.XCVR See transceiver.Term DefinitionDraftthe ther referenr referenes the use of tes the use ofehicles, aircraft andehicles, aircraft ositioning System, in whositioning Systemmit.mit. Frequency.eques standard that supporandard that supportsial Bus.al Bus.a specific lpecifor liner lin
MN003109A01_aaGlossary-4Draft
Draft
Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196 U.S.A.MOTOROLA, MOTO, MOTOROLA SOLUTIONS and  the Stylized M logo are trademarks or registered trademarks  of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.  © 2016 Motorola Solutions, Inc. All rights reserved. Oct 2016*MN003109A01*MN003109A01_AA

Navigation menu