Motorola Rmu2040 Users Manual RDX Series Two Way Radios

2014-12-11

: Motorola Motorola-Rmu2040-Users-Manual-120687 motorola-rmu2040-users-manual-120687 motorola pdf

Open the PDF directly: View PDF .
Page Count: 70

Download
Open PDF In Browser	View PDF

RM Series/Séries RM TwoWay Radios
Radios bidirectionnelles
User Guide
Guide de l’utilisateur

Models RMU2040, RMM2050 / Modèles RMU2043

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or
registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All
other trademarks are the property of their respective owners. ©2013 Motorola, Inc. All rights
reserved. Printed in Malaysia.
Motorola Solutions, Inc. 1301 East Algonquin Road Schaumburg, Illinois 60196, U.S.A.
800-367-2346 motorolasolutions.com

CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .5
Package Contents . . . . . . . . . . . . . . . . . . . . . .5
FCC Licensing Information . . . . . . . . . . . . .7
Canada Licensing Information . . . . . . . . . .7
General Information. . . . . . . . . . . . . . . . . . . . .7
The License Application . . . . . . . . . . . . . . . . .7
Batteries and Chargers
Safety Information . . . . . . . . . . . . . . . . . . . .8

11
11
11
11
13
13
14

CONTENTS

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Antenna . . . . . . . . . . . . . . . . . . . . . . . . .
LED Indicator . . . . . . . . . . . . . . . . . . . . .
Side Buttons . . . . . . . . . . . . . . . . . . . . .
The Lithium-Ion (Li-Ion) Battery . . . . . . .
Battery Features. . . . . . . . . . . . . . . . . . . . . .
About the Li-Ion Battery . . . . . . . . . . . . .
Battery Recycling and Disposal . . . . . . .
Installing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . . . .
Removing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . . . .

15
15

Power Supply, Adaptor and
Drop-in Tray Charger . . . . . . . . . . . . . . . 17

Operational Safety Guidelines. . . . . . . . . . . . .9

Battery Life Information . . . . . . . . . . . . . 18

Radio Overview . . . . . . . . . . . . . . . . . . . . .10

Charging the Battery . . . . . . . . . . . . . . . 20

Parts of the Radio . . . . . . . . . . . . . . . . . . . . .10
On/Off/Volume Knob. . . . . . . . . . . . . . . .11
Accessory Connector . . . . . . . . . . . . . . .11
Model Label . . . . . . . . . . . . . . . . . . . . . .11
Microphone . . . . . . . . . . . . . . . . . . . . . . .11
1

English

CONTENTS

Getting Started . . . . . . . . . . . . . . . . . . . . . .27
Turning radio ON/OFF. . . . . . . . . . . . . . . . . .27
Adjusting Volume . . . . . . . . . . . . . . . . . . . . .27
Selecting a Channel . . . . . . . . . . . . . . . . . . .27
Talking and Monitoring . . . . . . . . . . . . . . . . .27
Receiving a Call . . . . . . . . . . . . . . . . . . . . . .28
Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .28
Radio LED Indicators . . . . . . . . . . . . . . . . . .30
Hands-Free Use/VOX . . . . . . . . . . . . . . . . . .31
With Compatible VOX Accessories. . . . .31
Setting VOX Sensitivity . . . . . . . . . . . . . .32
Microphone Gain. . . . . . . . . . . . . . . . . . .32
Battery Save . . . . . . . . . . . . . . . . . . . . . .32
Reset to Factory Defaults . . . . . . . . . . . .32
End of Transmission Tone
(Roger Beep Tone) . . . . . . . . . . . . . . . . .33
Programming Features . . . . . . . . . . . . . . .34
Programming Mode. . . . . . . . . . . . . . . . . . . .34
Learning to Read the Values the
Radio Signals You . . . . . . . . . . . . . . . . .34
Entering Programming Mode . . . . . . . . .37
Reading Frequencies Values . . . . . . . . .37
English

Reading CTCSS/DPL Values . . . . . . . .
Reading Auto-Scan Values . . . . . . . . . .
Programming Frequencies, Codes
and Auto-Scan . . . . . . . . . . . . . . . . . . . .
Programming Mode FAQ . . . . . . . . . . . .
Programming Values Example. . . . . . . . . . .
Example of Programming a Frequency .
Example of Programming a Code . . . . .
Example of Programming Auto-Scan . .
Other Programming Features . . . . . . . . . . .
Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Scan List . . . . . . . . . . . . . . . . . .
Nuisance Channel Delete . . . . . . . . . . .
CPS (Computer Programming Software) . . .
Bandwidth Select . . . . . . . . . . . . . . . . . .
Time-Out Timer . . . . . . . . . . . . . . . . . . .
Power Select . . . . . . . . . . . . . . . . . . . . .
Battery Type Setting . . . . . . . . . . . . . . .
Call Tones . . . . . . . . . . . . . . . . . . . . . . .
Scramble . . . . . . . . . . . . . . . . . . . . . . . .
Reverse Burst . . . . . . . . . . . . . . . . . . . .
Cloning Radios. . . . . . . . . . . . . . . . . . . . . . .

38
39
39
40
41
41
42
43
44
44
45
45
46
47
47
47
47
47
48
48
49

Troubleshooting . . . . . . . . . . . . . . . . . . . . .54

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Accessories . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carry Accessories . . . . . . . . . . . . . . . . . . . .
Power Supplies AC Pin Adaptors. . . . . . . . .
Software Applications. . . . . . . . . . . . . . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supplies . . . . . . . . . . . . . . . . . . . . . .

71
71
71
72
72
72
72
72
73

CONTENTS

Cloning with a Multi Unit
Charger (MUC) . . . . . . . . . . . . . . . . . . . .49
Cloning Radio using the Radio
to Radio (R2R) Cloning Cable
(Optional Accessory). . . . . . . . . . . . . . . .51
Cloning using the CPS (Computer
Programming Software) . . . . . . . . . . . . .53

Use and Care . . . . . . . . . . . . . . . . . . . . . . .58
Frequency and Code Charts . . . . . . . . . . .59
RMU2043 - UHF Default
Frequencies Chart. . . . . . . . . . . . . . . . . . . . .59
RMU2040 - UHF Default
Frequencies Chart. . . . . . . . . . . . . . . . . . . . .60
CTCSS and PL/DPL Codes . . . . . . . . . . . . .61
Programming Customized Frequencies
66
Motorola Limited Warranty for
the United States and Canada . . . . . . . . . .67
Accessories . . . . . . . . . . . . . . . . . . . . . . . .71
3

English

SAFETY
PRODUCT SAFETY AND RF
EXPOSURE COMPLIANCE

!
SAFETY

Caution

Before using this product,
read the operating
instructions and RF energy
awareness information
contained in the Product
Safety and RF Exposure
booklet enclosed with your
radio.

ATTENTION!
This radio is restricted to occupational use only
to satisfy FCC RF energy exposure
requirements.

English

This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that
this device does not cause harmful
interference.

INTRODUCTION

Business Radios,
Mailstop 1C15, Motorola

Thank you for purchasing the Motorola® RM
Series Radio. This radio is a product of
Motorola's 80 plus years of experience as a
world leader in the designing and
manufacturing of communications equipment.
The RM Series radios provide cost-effective
communications for businesses such as retail
stores, restaurants, schools, construction sites,
manufacturing, property and hotel
management and more. Motorola professional
two-way radios are the perfect communications
solution for all of today's fast-paced industries.

8000 West Sunrise Boulevard

Note:

PACKAGE CONTENTS
•

Radio

•

Holster

•

Lithium-Ion Battery

•

Power Supply

•

Quick Reference Guide

•

Warranty Card

•

Drop-in Tray Charger

•

Product Safety & RF Exposure Booklet

INTRODUCTION

Read this user guide carefully to ensure you
know how to properly operate the radio
before use

Plantation, Florida 33322

English

This User Guide can be downloaded from
www.motorolasolutions.com/RMSeries.
Product-related questions, contact:
1-800-448-6686 (US and Canada)
1-888-390-6456 on your TTY (Text

INTRODUCTION

Telephone)

English

(FCC). To transmit on these frequencies, you

FCC LICENSING
INFORMATION

are required to have a license issued by the
FCC. Application is made available on FCC

INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC

Form 601 and Schedules D, H, and Remittance
Form 159.
To obtain these FCC forms, request document

this device does not cause harmful

000601 which includes all forms and

interference.

instructions. If you wish to have the document

RM Series Business two-way radios operate
on radio frequencies that are regulated by the

faxed, mailed or have questions, use the
following contact information.

Federal Communications Commission
Faxed contact the
Fax-On- Demand
system at:
1-202-418-0177

Mailed call the FCC forms hotline at:
1-800-418-FORM
1-800-418-3676

Questions regarding FCC
license contact the FCC at:

FCC LICENSING
INFORMATION

Rules. Operation is subject to the condition that

1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov

English

Before filling out your application, you must

Replacement of any transmitter component

decide which frequency(ies) you can operate

(crystal, semiconductor, etc.) not authorized by

on. See “Frequencies and Code Charts”. For

the FCC equipment authorization for this radio

questions on determining the radio frequency,

could violate FCC rules.

FCC LICENSING
INFORMATION

call Motorola Product Services at:

was intended to be distributed is subject to

Changes or modifications not expressly

government regulations and may be prohibited

approved by Motorola may void the user’s
authority granted by the FCC to operate this
radio and should not be made. To comply with
FCC requirements, transmitter adjustments
should be made only by or under the
supervision of a person certified as technically
qualified to perform transmitter maintenance
and repairs in the private land mobile and fixed
services as certified by an organization
representative of the user of those services.

English

Use of this radio outside the country where it

1-800-448-6686

GENERAL INFORMATION
The operation of your Motorola radio is subject
to the Radiocommunications Act and must
comply with rules and regulations of the
Federal Government’s department of Industry
Canada. Industry Canada requires that all
operators using Private Land Mobile
frequencies obtain a radio license before
operating their equipment.
An application for your Industry Canada license
is made on the form included with your radio.
Additional forms and latest license application
versions can be obtained from the nearest
Industry Canada District office. A list of these
offices is included for your information.

THE LICENSE APPLICATION

CANADA LICENSING

CANADA LICENSING
INFORMATION

General Instructions
1.

Fill in the items as per the instructions. If you
need additional space for any item use the
reverse side of the application.

Be sure to use a typewriter or print legibly.

Make a copy for your files.

Prepare a cheque or money order made out to
the “Receiver General for Canada”, for an
amount, which is on the following schedule, for
each radio purchased. (License is valid until
April 1st of each year, and the renewed.

Mail your completed application, along with your
cheque or money order to the closest Industry
Canada District office, according to the list on
pages

To obtain the latest Canadian License
Application form, please go to:
www.ic.gc.ca

English

BATTERIES AND CHARGERS
SAFETY INFORMATION

BATTERIES AND
CHARGERS SAFETY
INFORMATION

and cord, pull by the plug rather than the cord
when disconnecting the charger.
4.

An extension cord should not be used unless
absolutely necessary. Use of an improper

This document contains important safety and
operating instructions. Read these instructions
carefully and save them for future reference.

extension cord could result in risk of fire and
electric shock. If an extension cord must be
used, make sure that the cord size is 18AWG

Before using the battery charger, read all the
instructions and cautionary markings on

for lengths up to 6.5 feet (2.0 m), and 16AWG
for lengths up to 9.8 feet (3.0 m).

•

The charger,

•

The battery, and

not operate the charger if it has been broken or

•

The radio using the battery

damaged in any way. Take it to a qualified

To reduce risk of injury, charge only the
rechargeable Motorola-authorized batteries.

Use of accessories not recommended by
Motorola may result in risk of fire, electric
shock, or injury.

Do not disassemble the charger; it is not
repairable and replacement parts are not

Other batteries may explode, causing personal
2.

To reduce risk of fire, electric shock, or injury, do

Motorola service representative.

available. Disassembly of the charger may

injury and damage.

English

To reduce risk of damage to the electric plug

result in risk of electrical shock or fire.
7.

To reduce risk of electric shock, unplug the
charger from the AC outlet before attempting
any maintenance or cleaning

OPERATIONAL SAFETY
GUIDELINES
•

Turn the radio OFF when charging battery.

•

The charger is not suitable for outdoor use. Use
only in dry locations/conditions.

•

comply with the type and rating specified in the
equipment instructions.
•

Maximum ambient temperature around the power

•

Power output from the power supply unit must not

supply equipment must not exceed 40°C (104°F).

Connect charger only to an appropriately fused

exceed the ratings stated on the product label

and wired supply of the correct voltage (as

located at the bottom of the charger.

specified on the product).
•

In equipment using fuses, replacements must

•

Make sure that the cord is located where it will

Disconnect charger from line voltage by removing

not be stepped on, tripped over, or subjected to

main plug.

water, damage, or stress.

The outlet to which this equipment is connected
should be nearby and easily accessible.

BATTERIES AND CHARGERS
SAFETY INFORMATION

•

English

RADIO OVERVIEW
PARTS OF THE RADIO

Antenna
On/Off/Volume
knob
Microphone

PTT Button

Accessory
Connector

RADIO OVERVIEW
English

LED Indicator

Model Label

SB1-Monitor
Button
Lithium-Ion
battery

SB2- Scan/Nuisance
Channel delete

On/Off/Volume Knob
Used to turn the radio ON or OFF and to adjust
the radio’s volume.
Accessory Connector
Used to connect compatible audio accessories.
Model Label
Indicates the model of the radio.
Microphone
Speak clearly into the microphone when sending
a message.
Antenna On all RM Series radios, the antenna is
non-removable

Push-to-Talk (PTT) Button
• Press and hold down this button to talk,
release to leasten it
Side Button 1 (SB1)
• The Side Button 1 is a general button
that can be configured by the Computer
Programming Software - CPS. The
default setting of SB1 is ‘Monitor’.
Side Button 2 (SB2)
• The Side Button 2 is a general button
that can be configured by the CPS. The
SB2 default setting is set to scroll until
the desired channel is selected.
RM Series provides a Li-Ion battery. For more
information, see “Battery Feature on Pg.13.

RADIO OVERVIEW

LED Indicator
Used to give battery status, power-up status,
radio call information and scan status.

Side Buttons

English

RADIO OVERVIEW

This User Guide covers multiple RM Series
models, and may detail some features your
radio does not have. The radio’s model is
shown on the bottom of the radio and provides
you the following information:

English

Model

Frequency
Band

Transmit
Power
(Watts)

Number of
Channels

Antenna

RMU2043

UHF

Non-Removable

RMM2050

VHF- MURS

Non-Removable

RMU2043

UHF

Non-Removable

BATTERY FEATURES

About the Li-Ion Battery
The RM Series radio comes equipped with a
rechargeable Li-Ion battery. This battery
should be charged before initial use to ensure
optimum capacity and performance.

Motorola batteries are designed specifically to
be used with a Motorola charger and vice
versa. Charging in non-Motorola equipment
may lead to battery damage and void the
battery warranty. The battery should be at
about 77°F (25°C) (room temperature),
whenever possible. Charging a cold battery
(below 50° F [10°C]) may result in leakage of
electrolyte and ultimately in failure of the
battery. Charging a hot battery (above 95°F
[35°C]) results in reduced discharge capacity,
affecting the performance of the radio.
Motorola rapid-rate battery chargers contain a
temperature-sensing circuit to ensure that
batteries are charged within the temperature
limits stated above.

RADIO OVERVIEW

Battery life is determined by several factors.
Among the more critical are the regular
overcharge of batteries and the average depth
of discharge with each cycle. Typically, the
greater the overcharge and the deeper the
average discharge, the fewer cycles a battery
will last. For example, a battery which is
overcharged and discharged 100% several
times a day, lasts fewer cycles than a battery
that receives less of an overcharge and is
discharged to 50% per day. Further, a battery

which receives minimal overcharging and
averages only 25% discharge, lasts even
longer.

English

RADIO OVERVIEW

Battery Recycling and Disposal

English

Li-Ion rechargeable batteries can be recycled.
However, recycling facilities may not be
available in all areas. Under various U.S. state
laws and the laws of several other countries,
batteries must be recycled and cannot be
disposed of in landfills or incinerators. Contact
your local waste management agency for
specific requirements and information in your
area. Motorola fully endorses and encourages
the recycling of Li-Ion batteries. In the U.S. and
Canada, Motorola participates in the
nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for Li-Ion battery
collection and recycling.

Many retailers and dealers participate in this
program. For the location of the drop-off facility
closest to you, access RBRC's Internet web
site at:
www.rbrc.com
or call:
1-800-8-BATTERY
This internet site and telephone number also
provides other useful information concerning
recycling options for consumers, businesses
and governmental agencies.

Installing the Lithium-Ion (Li-Ion) Battery

Removing the Lithium-Ion (Li-Ion) Battery
1.

Turn OFF the radio.

Push down the battery latch and hold it

Pull the battery away from the radio.

depressed while removing the battery.

Turn OFF the radio.

With the Motorola logo side up on the battery

RADIO OVERVIEW

pack, fit the tabs at the bottom of the battery
into the slots at the bottom of the radio’s body.
3.

Press the top part of the battery towards the
radio until a click is heard.

Note:

To learn about the Li-Ion Battery Life
features, refer to “About the Li-Ion Battery”
on page 13
15

English

Power Supply and Drop-in Tray Charger

The radio is equipped with one Drop-in Tray
Charger and one Power Supply with Adaptor.
For details, see “Chargers” on page 72.

Slide the radio into the base of the holster and
then press the radio against the back of the
holster until the top clips are inserted in the
top latches of the battery.

To remove, detach the top clips of the holster
from the top latches of the battery and then
slide the radio up from the holster pocket.

RADIO OVERVIEW

Holster

English

Battery Life Information

RADIO OVERVIEW

When the Battery Save feature is ON (enabled by default) the battery life will be longer. The
following chart summarizes battery life estimations:

English

Note:

Battery life is estimated based on 5% transmit/ 5% receive/ 90% standby
standard duty cycle

Charging the Battery
The RM series radios offers two types

Charging with the Drop-in Tray
Single Unit Charger (SUC)

of power supplies:
•

Standard Power Supply and,

•

Rapid Power Supply.

Note:
The radio comes equipped with a
Standard Power Supply

RADIO OVERVIEW

To charge the battery (with the radio
attached), place it in a Motorola-approved
Drop-in Tray Single Unit Charger or Drop-in
Tray Multi Unit Charger.

English

Note: When acquiring additional chargers or
power supplies, make sure you have similar
drop-in tray chargers and power supplies
sets (all “rapid” or all “standard”). For part
number details, refer to “Chargers” on
page 72

Place the drop-in tray charger on a flat surface.

Insert the connector of the power supply into the
port on the side of the drop-in tray charger.

Plug the AC adaptor into a power outlet.

Insert the radio into the tray with the front of the
radio facing the front of the charger, as shown.

Note:

When charging a battery attached to a radio,
turn the radio OFF to ensure a full charge.
See “Operational Safety Guidelines” on
page 9 for more information

RADIO OVERVIEW

To charge only the battery - at step 4, insert the
battery into the tray, with the inside surface of
the battery facing the front of the charger, as
shown. Ensure the slots in the battery correctly
engage in the charger

English

Drop-in Tray Charger LED Indicators

RADIO OVERVIEW

English

Estimated Charging Time
The following table provides the estimated charging time of the battery. For further details, see
“Battery” on page 71.

RADIO OVERVIEW

English

Charging a Radio and Battery using
a Multi Unit Charger- MUC (Optional
Accessory)

Notes:
•

This Multi Unit Charger also allows you to
clone up to 2 radios (2 Source radios and 2
Target radios). Refer to page 51 for details.

•

Further details on MUC’s operation are explained
in the Instructions Sheet provided with the MUC.
For part number details, refer to the Accessories

RADIO OVERVIEW

section.

English

The Multi Unit Charger (MUC) allows drop-in
charging of up to 6 radios or batteries. Batteries
can be charged with the radios or removed and
placed in the MUC separately. Each of the 6
charging pockets can hold a radio (with or
without holster) or battery, but not both.
1.

Insert the power cord plug into the MUC’s jack.

Place the charger on a flat surface.

Plug the cord into an AC outlet.

Turn the radio OFF.

Insert the radio or battery into the charging
pocket.

For the following explanations, refer to “Parts of
the Radio” on page 10.
TURNING RADIO ON/OFF
To turn ON the radio, rotate the On/Off/Volume
Knob clockwise. The radio will chirp and the
LED Indicator will briefly blink red.
To turn the radio OFF, rotate the On/Off/Volume
Knob counterclockwise until you hear a ‘click’
and the radio LED Indicator turns OFF.
ADJUSTING VOLUME
Turn the On/Off/Volume Knob clockwise to
increase the volume, or counterclockwise to
decrease the volume.
Note:

Do not hold the radio too close to the ear
when the volume is high or when
adjusting the volume.

SELECTING A CHANNEL
To select a channel, press SB2 side button until
you reach the desired channel.Voice
announcement will indicate the channel selected.
2 channels are active with factory default setting.
Refer to "Advanced Radio Configuration" on
Page 34 to active more channels. The radio can
operate up to 4 channels.

GETTING STARTED

Each channel has its own Frequency,
Interference Eliminator Code and Scan Settings.
TALKING AND MONITORING
It is important to monitor for traffic before
transmitting to avoid ‘talking over’ someone
who is already transmitting.
To monitor, long press and hold the SB1(*)
button to access channel traffic. If no activity is
present, you will hear ‘static’. To release, press
SB1 again. Once channel traffic has cleared,
proceed with your call by pressing the PTT
button. When transmitting, the LED Indicator will
be On solid red during transmission.
27

English

GETTING STARTED

TALK RANGE

Notes:
•

To listen to all activity on a current channel, short
press the SB1 to set the CTCSS/DPL code to 0.
This feature is called ‘CTCSS/DPL Defeat
(Squelch set to SILENT)’.

•

(*) This assumes SB1 is not being programmed
for a different mode.

RECEIVING A CALL
1.

To select a channel, press SB2 side button
until you reach the desired channel, Voice
announcement will indicate the channel
selected

Make sure the PTT button is released and listen

The LED Indicator will be solid red while the

for voice activity.

radio is receiving a call.
4.

To respond, hold the radio vertically 1 to 2
inches (2.5 to 5cm) from mouth. Press the PTT
button to talk; release it to listen.

English

Channel: Current channel that the radio is
using, depending on radio model.

Frequency: The frequency the radio uses to
transmit/receive.

Interference Eliminator Code: These codes

Scramble Code: Codes that make the
transmissions sound garbled to anyone
listening who is not set to that specific code.

Bandwidth: Some frequencies have selectable
channel spacing, which must match other
radios for optimum audio quality (only
available for RMU2043).

For details on how to set up frequencies and
CTCSS/DPL codes in the channels, refer to
“Programming Selection Mode” in page 36.

GETTING STARTED

To establish a proper two-way communication,
the channel, frequency, and interference
eliminator codes must be the same on both
radios. This depends on the stored profile that
has been preprogrammed on the radio:

help minimize interference by providing a
choice of code combinations.

English

GETTING STARTED

RADIO LED INDICATORS
RADIO STATUS
Red heartbeat

Channel Busy

Solid orange

Cloning Mode

Two orange heartbeats

Cloning In Progress

Solid orange

Fatal Error at Power up

One green blink, one orange blink, one green blink, then repeat for 4
seconds

Low Battery

Orange blink

Low Battery Shutdown

Orange heartbeat

Monitor

LED is OFF

Power-Up

Solid red for 2 seconds

‘Idle’ Programming Mode /
Channel Mode

Green heartbeat

Scan Mode

Red Blink

Transmit (Tx)/Receive (RX)

Solid red

Transmit in Low Power Select

Solid Orange

Note:

English

LED INDICATION

Channel Alias Edit

Channel Alias Edit only applies to Display Models

HANDS-FREE USE/VOX

Turn the radio OFF.

Open accessory cover.

Insert the audio accessory’s plug firmly into

GETTING STARTED

accessory port.
4.

Turn radio ON. The LED Indicator will
blink double red.

Lower radio volume BEFORE placing
accessory near ear.

VOX
Accessory
Accessory
Port/
Connector

Motorola RM Series radios can operate
hands-free (VOX) when used with compatible
VOX accessories.
With Compatible VOX Accessories

To transmit, speak into accessory microphone
and to receive, stop talking.

VOX can be temporarily disabled by pressing
the PTT button or by removing the audio
accessory.

Note:

To order accessories, refer to:
www.motorolasolutions.com/RMseries or
call 1 (800) 448-6686, or contact your
Motorola point of purchase

The default factory setting for VOX sensitivity
level is OFF. Before using VOX, set VOX
level to a setting different from ‘OFF’ via the
CPS (Customer Programming Software).
Then, perform the following steps:
31

English

GETTING STARTED

Setting VOX Sensitivity

Battery Save

The sensitivity of the radio's accessory or
microphone can be adjusted to suit different
operating environments. VOX sensitivity can
be programmed via the CPS.

Battery Save feature extends battery life as
your radio goes into ‘Idle’ state. To enable/
disable press SB1 and SB2 buttons
simultaneously for 2 or 3 seconds while
powering up the radio until you hear a quick
series of beeps. To have a slightly better attack
time, set Battery Save feature to OFF so that
the radio is always ready to transmit or receive
without any delays.

Default value is OFF. If you want to use the
VOX feature, VOX level should be set at a
value different from OFF.
•

1 = Low audio input levels will trigger the Tx

•

2 = Medium sensitivity

•

3 = High audio input levels will trigger the Tx

Microphone Gain
The sensitivity of the microphone can be
adjusted to fit different users or operating
environments.
This feature can be adjusted only through the
CPS. Microphone default setting is set to 2 =
Medium Gain.

English

Note:

Battery Save feature is set to ON by default

Reset to Factory Defaults
Reset to Factory Defaults will set back all radio
features to the original factory default settings.
To do so, press PTT, SB2 and SB1
simultaneously while turning ON the radio until
you hear a high tone chirp.

GETTING STARTED

End of Transmission Tone (Roger Beep
Tone)
Short press the SB1 button while turning ON
the radio to enable/disable End of
Transmission Tone.
Note:

This setting is set to OFF by default

English

PROGRAMMING
FEATURES

To easily program all the features in your radio,
it is recommended to use the Costumer
Programming Software (CPS) and
programming cable.
CPS software download is available for free
at www.motorolasolutions.com/RMseries
Advanced Configuration
Advanced Configuration is a configuration
mode that allows the customization of
additional features via the front panel.
The non-display models don't have a display
to show programmed values, then
navigation is guided via voice prompt.

When the radio is set to Advanced
Configuration, you are able to read and modify
four features:
•

Frequency Selection

•

CTCSS/DPL Codes

•

Auto-Scan.

•

Active Channels

The Frequency Select feature allows you to
choose frequencies from a pre-defined list.
The Interference Eliminator Code (CTCSS/
DPL) helps minimize interference by providing
you with a choice of code combinations that
filter out static, noise, and unwanted
messages.
The Auto-Scan feature allows you to set a
particular channel to automatically enable Scan
each time you switch to that channel.
The Active Channels feature allows you to
increase or decrease the amount of channels
active (In the range of maximum channels).

English

Entering Advanced Configuration Mode
Note:

Before programming the features, make
sure your radio is set to the channel you
wish to program. You can do so before
entering Advanced Configuration Mode
or at any time during the Advanced
Configuration Mode by pressing SB2
until reaching the desired channel.

Note:

'Idle' Programming Mode is the stage of
the Programming Mode in which the
radio is waiting for the user to start the
radio programming cycle.

Entering Frequencies Values
RM Series radios have 89 frequencies for UHF.
Once in ‘Idle’ Programming Mode, the first
value available to change is Channel number,
you can change the channel by pressing SB2
button until you reach desired Channel, voice
announcement will indicate channel selected.
Using SB1 and SB2 you can change values.
The value selected is announced by voice
prompt.

PROGRAMMING
FEATURES

To read or modify Frequencies, Codes,
Auto-Scan or Active Channels, set the radio
to 'Advanced Configuration Mode' by
pressing and holding the PTT and SB1
buttons simultaneously for 3 to 5 seconds
while powering up the radio and until you
hear a voice prompt saying "Programming
Mode" and "Channel #".

Once you are in the 'Idle' Programming Mode,
you will be able to hear the Frequencies,
Codes, Auto-Scan and active channels
settings by short pressing the PTT button to
move along the different programmable
features.

English

PROGRAMMING
FEATURES

Reading CTCSS/DPL Values
If you continue short pressing the PTT button
the radio will move forward to programming
CTCSS/PL Codes.
After hearing the current value for CTCSS/PL
Code you can scroll to a new code value
using the SB1 or SB2 button.
RM Series have up to 122 codes available
(refer to “Frequencies and Codes Charts”
Section).
Reading Auto-Scan Values
After hearing the CTCSS/DPL codes, short
press the PTT button and the radio will move
forward to programming Auto-Scan.
Auto-Scan only has two values:
- Enabled
- Disabled
Note: While in Auto-Scan Mode, if you short press

PTT button, the radio will move forward to
programming the "Active Channels" feature, so
you can modify the amount of channels
available for your unit using the SB1 or SB2
button.

English

Saving Settings
If you are satisfied with the setting, you
can either:
•
•
•

short press PTT to continue
programming,
long press PTT to save and return to
'Idle' Programming Mode, or
long press the PTT button twice to exit
'Idle' Programming Mode and return to
the normal radio operation.

Note:

•

If you do not wish to save the value you just
programmed, turn the radio OFF.

•

If you ‘roll-over’ to the beginning of ‘Idle’
Programming Mode you will hear "Channel #"
and the LED Indicator will start blinking green
again. All values that were changed will be
automatically saved.

Programming Mode FAQ
1.

Return to 'Idle' Programming Mode and start
over.

PROGRAMMING
FEATURES

•

Long press the PTT button. The radio will return

•

Turn OFF the radio and enter Programming

to the 'Idle' Programming Mode or,
Mode again (see instructions in the beginning of
this section)

I am trying to program a frequency (or
code) value but the radio would not do it.

I got distracted while programming and
forgot which feature I was
programming. What should I do?

It rolled over and took me back to value
‘0’.
The radio will not allow you to program any
values that are not available in the frequencies
and codes pool. For example, if you try to
program code 128, the radio would not accept
it, as the maximum value allowed is 122. Same
thing will happen with frequencies. Check the
Frequencies and Codes Charts section to
make sure you are programming a valid
number.
3.

I am trying to enter the Programming
Mode but the radio would not do it.

The radio might be locked using the CPS to not
allow Front Panel Programming. To re-enable,
use the CPS.

English

4. When I was programming I made a
mistake and programmed the wrong

this channel and want to program another

value. How can I erase it or re-program
it?
If you make a mistake while programming a
value you have two choices:
•

The radio settings will roll-over each time
Keep increasing (short press SB1) or
decreasing (short pressing SB2) until you get

channel.
Press short PTT several times until you hear
"Channel #", then switch channel using
Channel Selector Knob. If you wish to save
the changes, make sure you are in the ‘Idle’
Programming Mode before switching the
channel as otherwise you will lose the changes
made.

the desired value or,

PROGRAMMING VALUES EXAMPLE

•

Turn OFF the radio and start-over.

I just programmed the value I wanted.

Example of Programming a Frequency

How do I exit Programming Mode?
•

If you are in Programming Mode you can exit by
long pressing the PTT button twice.

•

If you are already in the ‘Idle’ Programming
Mode, long press the PTT button once.

Assuming current frequency value is set to
Channel 1, with the UHF default frequency ‘02’
(equivalent to 464.5500 MHz), and you want to
change it to Frequency Number = ‘13’ (which is
mapped to 461.1375 MHz), follow this
sequence:
•

PROGRAMMING
FEATURES

they reach a maximum or minimum value.

I am done programming the features in

Enter Programming Mode

English

•

Short press the PTT button to enter Frequency

Example of Programming a Code

Programming Selection Mode. Radio will
•

Press SB1 button eleven times to scroll up the
frequency list and you will hear frequency "13"

Assuming current code value is set to factory
default ‘001’, and you want to change it to
CTCSS/DPL Code = 103 follow the sequence
below:

•

Long press the PTT button. LED Indicator will

•

Enter into Advanced Configuration Mode

•

Short press the PTT button twice and you will

announce current value ‘2’

PROGRAMMING
FEATURES

show a green heartbeat to indicate 'Idle' state.
•

Long press the PTT button to exit Programming

hear "Code #" (Entering CTCSS/DPL

Mode or turn radio OFF.

Programming Selection Mode).
•

Press and hold SB1 or SB2, selections shall
fast forward/rewind starting at the nearest 10's,
when released the radio starts playing the first,
second and third digit in full, keep pressing SB1/
SB2 several times until you hear "103"

•

Long press the PTT button. LED Indicator will
show a green heartbeat to indicate 'Idle' state.

•

Long press the PTT button to exit Programming
Mode or turn radio OFF.

English

Example of Programming Auto-Scan

Example of Programming Active Channels

Auto-Scan is the third Programming Mode
and can be set to either ON or OFF on a
particular channel.

Active Channels is the last Programming Mode and
It allows you to modify the number of active channels
the radio will be programmed to support.

To set Auto-Scan to ON:

To set Active Channels:

•

Enter into advanced Configuration Mode and
Short press the PTT button three times to enter
Auto-Scan Programming Selection Mode. The
radio will announce "Auto-Scan" and current

•

Active Channels Programming Selection Mode.
•

Short press the SB1 or SB2 buttons to

•

Long press the PTT button. LED Indicator will

•

Long press the PTT button to exit

show a green heartbeat to indicate “Idle” state.

Long press the PTT button. LED Indicator will
show a green heartbeat to indicate “Idle” state.
Long press the PTT button to exit

Short press the SB1 or SB2 buttons until you
hear the number of channels desired.

toggle Enabled/Disabled for the Auto-Scan
feature on the selected channel.

The radio will announce "Active Channels" and
current value.

setting (Enabled or Disabled).
•

Short press the PTT button Four times to enter

PROGRAMMING
FEATURES

•

Enter Programming Mode and select the
desired channel

select the desired channel.

Programming Mode or turn radio OFF.

English

OTHER PROGRAMMING FEATURES

PROGRAMMING
FEATURES

Scan
Scan allows you to monitor other channels to detect
conversations. When the radio detects a
transmission, it will stop scanning and will receive on
the active channel. This will allow you to listen and
talk to people on that channel without having to
change channel. If there is are transmissions on
another channel once the radio has stopped
scanning then you will not hear that activity. After
activity has ceased on the channel which the radio
has stopped, scanning will resume again after 5
seconds of no activity on that channel.
•

To start scanning, press the SBx (x=1 or 2)
button (Scan has to be programmed to either
SB1 or SB2 via CPS). SB2 default is Scan/
Nuisance delete,

English

•

To stop scanning, short press the SBx
button again.

•

By pressing the PTT button while the radio is
scanning, the radio will transmit on the channel
which was selected before Scan was activated.
If no transmission occurs within five seconds,
scanning will resume.

•

If you want to scan a channel without
Interference Eliminator Codes (CTCSS/DPL),
set the code settings for the channels to ‘0’ in the
CTCSS/DPL Programming Selection Mode.

Whenever the radio is set up in Scan, the LED
Indicator will signal a Red blink.

Editing Scan List

To delete a channel from the Scan List:

Scan Lists can be edited by using the CPS
(refer to CPS section on page 46)

•

Nuisance Channel Delete

•

Wait until the radio stops on the channel
•

you wish to eliminate, then long press the
SBx button to delete it.
The channel will not be scanned again
until you exit Scan by short pressing the
SBx button again or by turning the radio
OFF and back ON.

PROGRAMMING
FEATURES

Nuisance Channel Delete allows you to
temporarily remove channels from the Scan
List. This feature is useful when frequent,
irrelevant conversations on a channel tie up
the scanning feature, becoming a nuisance
to the user.

To start scanning, press the SBx (x=1 or
2) button (Scan has to be programmed to
either SB1 or SB2 via CPS). SB2 default
is Scan/Nuisance delete,

English

CPS (COMPUTER PROGRAMMING
SOFTWARE)

To program, connect the RM Series radio
via the Drop-in Charger Tray and CPS

PROGRAMMING
FEATURES

Programming Cable as shown in the picture
above.

The easiest way to program or change features
in your radio is by using the Computer
Programming Software (CPS) and the CPS
Programming Cable(*). CPS Software is
available for free as web based downloadable
software at:
www.motorolasolutions.com/RMseries

English

CPS allows the user to program frequencies,
PL/DPL codes, as well as other features such
as: Bandwidth Select, Time-out Timer, Power
Select, Scan List, Call Tones, Scramble,
Reverse Burst, etc. CPS is a very useful tool
as it can also lock the Front-Panel Radio
Programming to avoid accidentally erasing the
current radio settings. It also provides security
by giving the option to set up a password for
radio profile management. Please refer to
Features Summary Chart Section at the end
of the user guide for more details.
Note:

(*) CPS Programming Cable P/N HKKN4027A
is an accessory sold separately. Please
contact your Motorola point of purchase for
more information.

Bandwidth Select (Only Canada models)

Power Select

All US models are compliants with the
narrowbandwith FCC regulation.

Power Select allows you to select between
high and low transmission power per channel.
The power levels for RM Series toggle
between 2W and 1W.

Default setting for Bandwidth Select depends
on the specific frequency and channel. Some
frequencies have selectable channel spacing,
which must match with other radios for
optimum audio quality.

Time-Out Timer
When pressing the PTT button, transmissions
will be terminated after a preset time of
continuous transmitting. The default setting
is 60 sec and can be changed using the CPS.
Scramble
The Scramble feature makes transmissions
sound garbled to anyone listening without the
same code. Scramble default value is OFF.
The Scramble feature must be programmed
to SB1 or SB2.

Call Tones feature allows you to transmit an
audible tone to other radios on the same
channel and alerting them that you are about
to talk or alerting them
without speaking. The call tones feature must
be programmed to SB1 or SB2 and 1 of 3 prerecorded tones selected
Reverse Burst
Reverse Burst eliminates unwanted noise
(squelch tail) during loss of carrier detection.
You can select values of either 180 or 240 to
be compatible with other radios. Default is
180.

PROGRAMMING
FEATURES

For details, refer to Frequency and Code
Charts section.

Call Tones

Notes: Some of the features available with the CPS
software may vary depending on the radio
model.
47

English

CLONING RADIOS
You can clone RM Series radio profiles from
one Source radio to a Target radio by using any
one of these 3 methods:
•
•

Using a Multi Unit Charger (MUC - optional
accessory),
Two Single Unit Chargers (SUC) and a Radio-toRadio cloning cable (optional accessory),
the CPS (free software download) and CPS
programming cable ((optional accessory).

a Target radio (the radio which profile will be
cloned from the source radio.)

The Source radio has to be in Pocket 1 or 4
while the Target radio has to be in Pocket 2 or
5, matching in the MUCs pockets by pairs as
follows:
•

1 and 2 or,

•

4 and 5

Cloning with a Multi Unit Charger (MUC)
When cloning, the MUC does not need to be
plugged into a power source, but ALL radios
require charged batteries.
1.

Turn ON the Target radio and place it into one of

Power the Source radio following the sequence

PROGRAMMING
FEATURES

•

or copied from) and
•

the MUC Target Pockets
below:

To clone radios using the MUC, there must be
at least two radios:
•

•

Long press the PTT button and SB2
simultaneously while turning the radio ON.

a Source radio (radio which profiles will be cloned

English

PROGRAMMING
FEATURES

•

Wait for 3 seconds before releasing the
buttons until a distinctive audible tone is
heard and ‘Cloning’ is announced.

Place the Source radio in the source pocket
that pairs with the target pocket you chose in
step 1. ress ̀ and release SB1 on Source
radio.

After cloning is completed, the Source radio will a
nnounce either ‘Successful’ (cloning wa
successful) or ‘failed’ (cloning process has failed).

Once you have completed the cloning
process, turn the radios OFF and ON to exit
the ‘cloning’ mode.

•

English

If cloning fails please refer to “What To Do
if Cloning Fails” on page 54.

When ordering the MUC, please refer
to P/N PMLN6384A.
Notes:
•

Paired Target radios and Source radios must
be of the same band type in order for the
cloning to run successfully.

•

MUC pockets numbers should be read from
left to right with the Motorola logo facing front.

CPS and Cloning Cables (Optionals)
•

CPS Cable

Both CPS and Cloning cables are made to
work either with RM Series radios or RDX
series. Cloning cable also can work with a
mix of RDX and RM radios.

•

The CPS cable is made to program RM

Cloning Cable

series radio when the switch is in "Flash"

PROGRAMMING
FEATURES

position. If you want to use the CPS cable
to program an RDX radio, make sure the
switch is in "CPS" position and attach a
USB convertor provided as part of the CPS
cable kit.
•

Cloning cable allows you to clone:

Micro-to-Mini USB Convertor
USB Converter

- RM Series, make sure the switch is in
"Cloning" position.
- RDX radios, make sure the switch is in
"Legacy" position there is one USB
converter attached on each side.
- RM and RDX radios, make sure the switch
is in "Legacy" position and use a USB
converter to connect to the RDX SUC.
Cloning cable kit provides 1 USB convertor.
51

English

Cloning Radio using the Radio to Radio
(R2R) Cloning Cable (Optional Accessory)

Unplug any cables (power supply or USB
cables) from the SUCs.

Plug one side of the cloning cable mini
connector to one SUC. Plug the other end to
the second SUC.

Note:

Turn ON the Target radio and place it into one of

On the Source radio, power the radio following

the SUCs.
the sequence below:

Operating Instructions
1.

• Long press the PTT button and SB2

Before beginning the cloning process, make

simultaneously while turning the radio

sure you have:

ON.

• A fully charged battery on each one of

• Wait for 3 seconds before releasing the

the radios.
• Two Single Unit Chargers (SUC).
Either 2 SUC for RM Series or 1 SUC
for RM Series and 1 SUC for RDX
Series
• Turn OFF the radios and,

PROGRAMMING
FEATURES

During the cloning process no power is
being applied to the SUC. The batteries will
not be charged. A data communication is
being established between the two radios.

buttons until you hear a distinctive
audible tone and the word "Cloning"
6.

Place the Source radio in its SUC, press and
release SB1.

English

After cloning is completed, the Source radio will

announce either ‘pass’ (cloning was
successful) or ‘fail’ (cloning process has

to the radio.
4.

failed). If the Source radio is a display model, it
will either show ‘Pass’ or ‘Fail’ on the display (a

PROGRAMMING
FEATURES

tone will be heard within 5 seconds).

The radio will emit "Fail" indicating that the
cloning process has failed. In the event that
cloning fails, try performing each of the
following before trying to start the cloning
process again:
1.

Ensure that the batteries on both radios are fully

Check the cloning cable connection on both

charged.
SUCs.

English

Ensure that the Target radio is turned ON.

Ensure that the Source radio is in cloning mode.

Ensure that radios are both from the same
frequency band, same region and same
transmission power.

turn the radios OFF and ON to exit ‘clone’

What To Do if Cloning Fails

Ensure that there is no debris in the charging
tray or on the radio contacts.

Once you have completed the cloning process,
mode.

Ensure that the battery is engaged properly on

Note:

This cloning cable is designed to operate
only with compatible Motorola SUC
RLN6175 and PMLN6394A

When ordering Cloning Cable please refer to
P/N HKKN4028A. For details about
accessories refer to Accessories section.

Cloning using the CPS (Computer
Programming Software)
When cloning using this method, you will need
to have the CPS software, a Drop-in Tray
Charger and the CPS Programming Cable.
To order the CPS Programming
Cable, please refer to HKKN4028A

•

PROGRAMMING
FEATURES

Information on how to clone using the CPS is
available either in:
the CPS Help File --> Content and Index -->
Cloning Radios, or
•

in the CPS Programming Cable Accessory
Leaflet.

English

TROUBLESHOOTING
Try This... Recharge

Symptom
or replace the Li-Ion battery.
No Power

Extreme operating temperatures may affect battery life.
Refer to See “About the Li-Ion Battery” on page 14.
Confirm Interference Eliminator Code is set.

Hearing other noises or
conversation on a channel

Frequency or Interference Eliminator Code may be in use.
Change settings: either change frequencies or codes on all radios.
Make sure radio is at the right frequency and code when transmitting.

TROUBLESHOOTING

Refer to “Talking and Monitoring” on page 27

English

Message Scrambled

Audio quality not good enough

Scramble Code might be ON, and/or setting does not match the other radios'
settings.

Radio settings might not be matching up correctly. Double check frequencies,
codes and bandwidths to make sure they are identical in all radios

Try This...

Symptom

Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease
range. Check for clear line of sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt decreases range.
Change location of radio. To increase range and coverage, you can reduce
Limited talk range

obstructions, increase power. UHF radios provides greater coverage in
industrial and commercial buildings. Increasing power provides greater signal
range and increased penetration through obstructions.
Refer to See “Talking and Monitoring” on page 27.
Make sure the PTT button is completely pressed when transmitting.
Confirm that the radios have the same Channel, Frequency, Interference
Eliminator Code and Scramble Code settings. Refer to “Talking and Monitoring”
section on page 27 for further information.
Recharge, replace and/or reposition batteries. Refer to “About your Li-Ion

received

Battery” section on page 14.
Obstructions and operating indoors, or in vehicles, may interfere. Change
location. Refer to “Talking and Monitoring” Section on page 27.
Verify that the radio is not in Scan. Refer to “Scan” on page 44 and “Nuisance
Channel Delete” on page 45.

TROUBLESHOOTING

Message not transmitted or

English

Try This...

Symptom

Radios are too close; they must be at least five feet apart.
Heavy static or interference

Radios are too far apart or obstacles are interfering with transmission.
Refer to “Talking and Monitoring” on page 27.
Recharge or replace Li-Ion battery. Extreme operating

Low batteries

temperatures affect battery life. Refer to “About the LiIon Battery” on page 14.
Check that the radio/battery is properly inserted and check the battery/charger

Drop-in Charger LED light
does not blink

contacts to ensure that they are clean and charging pin is inserted correctly.
Refer to “Charging the Battery” section on page 21, “Drop-in Tray Charger LED
Indicators” section on page 24 and “Installing the Lithium-Ion Battery” section

TROUBLESHOOTING

on page 16.

English

Low battery indicator is
blinking although new
batteries are inserted

Refer to “Installing the Li-Ion Battery” section on page 16 and “About your
Li-Ion Battery” section on page 14.

Try This...

Symptom

VOX feature might be set to OFF.
Cannot activate VOX

Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’.
Accessory not working or not compatible.
Refer to “Hands-Free Use/VOX” section on page 31.
Check drop-in tray charger is properly connected and correspond to a
compatible power supply.

Battery does not charge
although it has been placed in
the drop-in charger for a while

Ensure that you have the drop-in tray charger adjustable piece placed on the
right position.
Refer to “Charging with the Drop-In Tray Single Unit Charger” section on
page 21 and “Charging a Standalone Battery” section on page 22.
Check the charger’s LEDs indicators to see if the battery has a problem. Refer
to “Drop-in Tray Charger LED Indicators” section on page 24.

Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check
to see if the radio has been programmed using the CPS with a customized profile.

TROUBLESHOOTING

Note:

English

USE AND CARE

Use a soft damp cloth
to clean the exterior

Do not immerse
in water

Do not use alcohol or
cleaning solutions

If the radio is submerged in water...

Turn radio OFF and
remove batteries

English

Dry with soft cloth

Do not use radio until
completely dry

FREQUENCY AND CODE CHARTS
RMU2043 - UHF DEFAULT FREQUENCIES CHART
RM UHF 4CH Radios Default Frequencies - RMU2043
Frequency #

Frequency
(MHz)

Code #

Code

Bandwidth

458.6625

67.0 Hz

12.5 kHz

469.2625

67.0 Hz

12.5 kHz

FREQUENCY AND CODE

Channel

English

RMU2040 - UHF DEFAULT FREQUENCIES CHART

FREQUENCY AND CODE

RM UHF 4 CH Radios Default Frequencies - RMU2040

English

FREQUENCY AND CODE

RMM2050 - MURS DEFAULT FREQUENCIES CHART

English

CTCSS AND PL/DPL CODES
CTCSS Codes
CTCSS

CTCSS

67.0

107.2

167.9

71.9

110.9

173.8
179.9

74.4

114.8

77.0

118.8

186.2

79.7

123

192.8

82.5

127.3

203.5

85.4

131.8

210.7

88.5

136.5

218.1

91.5

141.3

225.7
233.6

94.8

146.2

97.4

151.4

241.8

100.0

156.7

250.3

103.5

162.2

122 (*)

69.3

13
Note:

FREQUENCY AND CODE

3
4

(*) New CTCSS code.

English

PL/DPL Codes
Code

DPL

Code

DPL

Code

116

243

125

244

131

245

132

251

134

261

143

263

152

265

FREQUENCY AND CODE

DPL

English

155

271

156

306

162

311

165

315

172

331

174

343

205

346

114

223

351

115

226

364

PL/DPL Codes (Continued)
DPL

Code

DPL

Code

DPL

Code

365

104

565

121

754

371

105

606

123

645

411

106

612

124

Customized PL

412

107

624

125

Customized PL

413

108

627

126

Customized PL

423

109

631

127

Customized PL

431

110

632

128

Customized PL

432

111

654

129

Customized PL

445

112

662

130

Inverted DPL 39

464

113

664

131

Inverted DPL 40

465

114

703

132

Inverted DPL 41

466

115

712

133

Inverted DPL 42

503

116

723

134

Inverted DPL 43

100

506

117

731

135

Inverted DPL 44

101

516

118

732

136

Inverted DPL 45

102

532

119

734

137

Inverted DPL 46

103

546

120

743

138

Inverted DPL 47

FREQUENCY AND CODE

88
89

English

FREQUENCY AND CODE

PL/DPL Codes (Continued)

English

DPL

Code

DPL

Code

DPL

Code

139

Inverted DPL 48

156

Inverted DPL 65

173

Inverted DPL 82

140

Inverted DPL 49

157

Inverted DPL 66

174

Inverted DPL 83

141

Inverted DPL 50

158

Inverted DPL 67

175

Inverted DPL 84

142

Inverted DPL 51

159

Inverted DPL 68

176

Inverted DPL 85

143

Inverted DPL 52

160

Inverted DPL 69

177

Inverted DPL 86

144

Inverted DPL 53

161

Inverted DPL 70

178

Inverted DPL 87

145

Inverted DPL 54

162

Inverted DPL 71

179

Inverted DPL 88

146

Inverted DPL 55

163

Inverted DPL 72

180

Inverted DPL 89

147

Inverted DPL 56

164

Inverted DPL 73

181

Inverted DPL 90

148

Inverted DPL 57

165

Inverted DPL 74

182

Inverted DPL 91

149

Inverted DPL 58

166

Inverted DPL 75

183

Inverted DPL 92

150

Inverted DPL 59

167

Inverted DPL 76

184

Inverted DPL 93

151

Inverted DPL 60

168

Inverted DPL 77

185

Inverted DPL 94

152

Inverted DPL 61

169

Inverted DPL 78

186

Inverted DPL 95

153

Inverted DPL 62

170

Inverted DPL 79

187

Inverted DPL 96

154

Inverted DPL 63

171

Inverted DPL 80

188

Inverted DPL 97

155

Inverted DPL 64

172

Inverted DPL 81

189

Inverted DPL 98

PL/DPL Codes (Continued)
Code

DPL

Code

DPL

Code

190

Inverted DPL 99

200

Inverted DPL 109

210

Inverted DPL 119

191

Inverted DPL 100

201

Inverted DPL 110

211

Inverted DPL 120

192

Inverted DPL 101

202

Inverted DPL 111

212

Inverted DPL 121

193

Inverted DPL 102

203

Inverted DPL 112

213

Inverted DPL 123

194

Inverted DPL 103

204

Inverted DPL 113

214

Customized DPL

195

Inverted DPL 104

205

Inverted DPL 114

215

Customized DPL

196

Inverted DPL 105

206

Inverted DPL 115

216

Customized DPL

197

Inverted DPL 106

207

Inverted DPL 116

217

Customized DPL

198

Inverted DPL 107

208

Inverted DPL 117

218

Customized DPL

199

Inverted DPL 108

209

Inverted DPL 118

219

Customized DPL

FREQUENCY AND CODE

DPL

English

MOTOROLA LIMITED
WARRANTY FOR THE
UNITED STATES AND
CANADA
What Does this Warranty Cover?

Products Covered

Length of Coverage

Products and
Accessories as defined
above, unless otherwise
provided for below.

One (1) year from the date
of purchase by the first
consumer purchaser of the
product unless otherwise
provided for below.

Decorative
Accessories and
Cases.
Decorative covers,
bezels, PhoneWrap™
covers and cases.

Limited lifetime warranty
for the lifetime of ownership
by the first consumer
purchaser of the product.

Business Two-way
Radio Accessories

One (1) year from the date
of purchase by the first
consumer purchaser of the
product.

Products and
Accessories that are
Repaired or Replaced.

The balance of the original
warranty or for ninety (90)
days from the date returned
to the consumer, whichever
is longer.

WARRANTY

Subject to the exclusions contained below,
Motorola, Inc. warrants its telephones, pagers, and
consumer and business two-way radios (excluding
commercial, government or industrial radios) that
operate via Family Radio Service or General
Mobile Radio Service, Motorola-branded or
certified accessories sold for use with these
Products (“Accessories”) and Motorola software
contained on CD-ROMs or other tangible media
and sold for use with these Products (“Software”)
to be free from defects in materials and
workmanship under normal consumer usage for
the period(s) outlined below.
This limited warranty is a consumer's exclusive
remedy, and applies as follows to new Motorola
Products, Accessories and Software purchased by
consumers in the United States, which are
accompanied by this written warranty.

Products and Accessories

English

WARRANTY

Exclusions

English

Normal Wear and Tear. Periodic maintenance,
repair and replacement of parts due to normal
wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged
capacity falls below 80% of their rated capacity
and batteries that leak are covered by this limited
warranty.
Abuse & Misuse. Defects or damage that result
from: (a) improper operation, storage, misuse or
abuse, accident or neglect, such as physical
damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with
liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (d)
other acts which are not the fault of Motorola, are
excluded from coverage.

Use of Non-Motorola Products and
Accessories. Defects or damage that result from
the use of Non-Motorola branded or certified
Products, Accessories, Software or other
peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects
or damages resulting from service, testing,
adjustment, installation, maintenance, alteration,
or modification in any way by someone other than
Motorola, or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with
(a) serial numbers or date tags that have been
removed, altered or obliterated; (b) broken seals
or that show evidence of tampering; (c)
mismatched board serial numbers; or (d)
nonconforming or non-Motorola housings, or
parts, are excluded form coverage.

Communication Services. Defects, damages, or
the failure of Products, Accessories or Software
due to any communication service or signal you
may subscribe to or use with the Products
Accessories or Software is excluded from
coverage.

Software. Applies only
to physical defects in
the media that
embodies the copy of
the software (e.g. CDROM, or floppy disk).

WHO IS COVERED?
This warranty extends only to the first consumer
purchaser, and is not transferable.

Software
Products Covered

Software NOT Embodied in Physical Media.
Software that is not embodied in physical media
(e.g. software that is downloaded from the
internet), is provided “as is” and without warranty.

Length of Coverage

HOW TO OBTAIN WARRANTY SERVICE OR
OTHER INFORMATION?
Contact your Motorola point of purchase.

Ninety (90) days from the
date of purchase.

Exclusions

The Motorola products described in this manual
may include copyrighted Motorola and third party
software stored in semiconductor memories or
other media. Laws in the United States and other
countries preserve for Motorola and third party
software providers certain exclusive rights for
copyrighted software, such as the exclusive rights
to distribute or reproduce the copyrighted
software. Accordingly, any copyrighted software
contained in the Motorola products may not be
modified, reverse-engineered, distributed, or
reproduced in any manner to the extent allowed by
law.
69

WARRANTY

Software Embodied in Physical Media. No
warranty is made that the software will meet your
requirements or will work in combination with any
hardware or software applications provided by
third parties, that the operation of the software
products will be uninterrupted or error free, or that
all defects in the software products will be
corrected.

SOFTWARE COPYRIGHT NOTICE

English

Furthermore, the purchase of the Motorola
products shall not be deemed to grant either
directly or by implication, estoppel, or otherwise,
any license under the copyrights, patents, or
patent applications of Motorola or any third party
software provider, except for the normal, nonexclusive, royalty-free license to use that arises by
operation of law in the sale of a product.

PATENT NOTICE

WARRANTY

This product is covered by one or more of the
following United States patents.
5896277 5894292 5864752 5699006 5742484
D408396 D399821 D387758 D389158 5894592
5893027 5789098 5734975 5861850 D395882
D383745 D389827 D389139 5929825 5926514
5953640 6071640 D413022 D416252 D416893
D433001

English

EXPORT LAW ASSURANCES
This product is controlled under the export
regulations of the United States of America. The
Governments of the United States of America may
restrict the exportation or re-exportation of this
product to certain destinations. For further
information contact the U.S. Department of
Commerce.

ACCESSORIES

Part No.

Description

53815

Headset w/Boom Mic BR

HMN9026ER

Remote Speaker Mic BR

HKLN4477

Surveillance Earpiece BR

Part No.

ACCESSORIES

BATTERY

AUDIO ACCESSORIES

Description

53865

Headset w/Swivel Boom Mic

53866

Earbud w/Clip PTT Mic BR

56517

Earpiece w/Inline Mic

RLN6423

Swivel Earpiece BR

English

Carrying

ACCESSORIES

CABLES
Part No.

Description

HKKN4028A

Radio to Radio Cloning Cable

HKKN4027A

CPS Programming Cable

CHARGERS
Part No.

English

Description

PMLN6394A

Standard Charging Solution

PMLN6392A

Rapid Charging Solution

Part No.
HKLN4510A

Description

RM Swivel Holster

m
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks
or registered trademarks of Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their respective owners. ©2013 Motorola,
Inc. All rights reserved. Printed in Malaysia.

Motorola Solutions, Inc. 1301 East Algonquin Road Schaumburg, Illinois 60196,
U.S.A. 800-367-2346 motorolasolutions.com

68012009071

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Motorola Solutions GCD Penang
Create Date                     : 2012:01:05 14:13:29Z
Modify Date                     : 2014:12:07 14:27:53+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : FrameMaker 8.0
Metadata Date                   : 2014:12:07 14:27:53+08:00
Format                          : application/pdf
Title                           : RDX Series Two Way Radios
Creator                         : Motorola Solutions GCD Penang
Document ID                     : uuid:42027014-e4d6-4487-9654-b1efed0698b0
Instance ID                     : uuid:3c8a5dd6-fd7c-5c42-9139-05f3c99bc827
Page Mode                       : UseOutlines
Page Count                      : 70

EXIF Metadata provided by EXIF.tools

Motorola Rmu2040 Users Manual RDX Series Two Way Radios

Navigation menu

Versions of this User Manual:

Views

Navigation