Multiplex USA PROFIROYAL Model Aircraft Radio Control Transmitter User Manual User Man4

Download:
Mirror Download [FCC.gov]
Document ID	82565
Application ID	rhqpexBAZI7yzLMZGvJp+A==
Document Description	User Man4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	196.36kB (2454543 bits)
Date Submitted	2000-01-21 00:00:00
Date Available	2000-03-06 00:00:00
Creation Date	2000-01-21 08:51:47
Producing Software	Acrobat 4.0 Import Plug-in for Windows
Document Lastmod	2000-01-21 08:52:31
Document Title	User Man4
Document Creator	Acrobat 4.0 Import Plug-in for Windows

_Uu|vn owl .
At this point you should set the trensmitter‘s
modulation to match the receiver you will be using.
it your receiver is an Ex 12 DS you don't need to
make any changes. You can move straight on to paint
Enter the menu cycle '
3.4 Changing the control asslgnmenls
Note: the controls will be interchanged! -
For example. if you assign RUDDER to transmitter
control A. AlLEHON will automatically be switched to
control C. This prevents the danger oi assigning two
difierent transmitter controls to one iunction.
_ Open modulation field (flashes)
6/8 or Be Select PPM 7, PPM 9, PPM 12 or
POM/A
_ Open neutral point field (flashes)
El/Ei Select MPX (=MULTIPLEX) = 1,6 ms
or OTHER - 1.5 ms
Bank to the operating screen
3.3 Cheoklng the control assignments
in the Glider Butterfl" base type the transmitter
controls are arranged as foliowe:
If this arrangement suits your normal mode 01 flying,
you can move straight on to point "3.5 Connecting
servos“.
Repeat the next two steps until the control
alTanoement meets your requirements
Open 'CONTROL" field
Select the transmitter control using
iii/El or the Digi-edjustor.
Open the “OPERATES" field
Select the iunotlon with E/El or the
Digi-adiustor.
PROM me 4000
3.5 Connecting servos
Recommendation: luve the servo MM
mixing it you want e quick etartl
Connect the servos to the receiver in the sequence
stated in the bese‘type diagram (n page 77). when
you re-asslgn servos, all the mixer inputs are set to
10036 and all serves to “normal" direction.
For the ‘Glider Butterfl” base type you should connect
the servos in your model as iollows:
v h". we
01 course, you don t need to connect functions which
don't exist in your model.
Serves 10. 11 and 12 can only be connected if you
are using an Fix 12 DS receiver ln PPM 12 mode.
3.5 Checking (matching) mixer Inputs
In the “Adjust servos, travels and switches" menu you
can do the following:
- set mixer Input values,
~ reverse mixer inputs, and
- assign switches to the mixer inputs
This is the procechre:
Quick start
You have to repeat the tolinwing steps iur all servos.
Open “SERVO“ field
Select the serve with El/El or the Digi-
adjusmr.
Open the ‘lNPUT' field
Select the input with ENE] or the Digi-
adjuster.
Open the ediust field
Move the associated control
Reverse the input with the human
Adjust the mixer input with iii/El or
the Dial-adjuster.
Open the Switch field
Select ONIOFF or a switch
The brackets round the buttons indicate that you only
have to make changes here it it is necessary,
Once everything is as you want it:
in) ’
Back to the operating screen
oulck start
4. The first helicopter
me basic preparations are abbreviated slightly here
as they have already been described under the same
section letters In Section 1.) The thirteen-s page 6
on).
4. 1 Basic preparations
Charge mnsmltter and receiver batteries
Prepare the receiver
ll you want to use an Rx 12 DS receiver in the PPMQ
mode with only one receiver battery. iumpers must be
titted in sockets 8 HF and B ”Hz. The battery should
be connected to socket 8 1-6.
Fltthe crystals
For the Rx 12 DS receiver you need a double
superhet crystal with a clear plastic sleeve.
The transmitter and receiver crystals must be on the
same channel.
Schemallcdlegmm aftherotorlveadlorthe
"Trainer 120 “animus type
4.2 Select base type
t,
For our "quick start" we have selected the "Trainer g
120 deg" base type. The assignment oi transmitter
controls, switches and serves Is desuibed in detail 0
page 39
Before you can select the base type you have to
switch to an “empty” memory.
This is the procedure:
Open the Memory" field
Leaf through with El/El or the Digi-
adjustor until Luv—EMPTY -—~--"
3999378
Confirm with the button
If you press any other button, the
memory switch will not take place.
The base type select field is
automatically opened (flashes)
Laal through with Elel or the Digi-
adjustor until "9 Trainer 120 deg"
appears.
The figure 9 in the last line is the running number of
the “Trainer 120 deg“ base type.
confirm with the El button
_ Back to the operating screen

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:01:21 08:52:31-05:00
Create Date                     : 2000:01:21 08:51:47-05:00
Creator                         : Acrobat 4.0 Import Plug-in for Windows
Producer                        : Acrobat 4.0 Import Plug-in for Windows
Page Count                      : 3

EXIF Metadata provided by EXIF.tools