Murata LB1MDIMP004 LCEE5ZZ1MD-011 User Manual SP ZZ1MD J submittedx

Murata Manufacturing Co., Ltd. LCEE5ZZ1MD-011 SP ZZ1MD J submittedx

UserManual.wiki >

LB1MDIMP004 User Manual

user manual

Preliminary Specification Number : SP-ZZ1MD-J Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. WiFi / Bluetooth Module Data Sheet Cypress CYW43438 WLAN / BT + ST Micro STM32F412 MCU for 802.11b/g/n & Bluetooth® 4.1 Electric Imp P/N : imp004m MURATA P/N : LBEE5ZZ1MD-011 This Datasheet is preliminary version, and subject to change without notice.

Preliminary Specification Number : SP-ZZ1MD-J 1 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Revision history Issued Date Revision Code Revision Page Changed Items Change Reason Jul. 6. 2016 First Issue Sep. 9. 2016 A P3 P4 P6 P15 P17 2. Part Number 4.1. Dimensions 4.2. Terminal Configurations 11. Land pattern (Top View) 13. Tape and Reel Packing Oct. 11. 2016 B P3 P4 P6 P10 P12 2. Part Number 4.1. Dimensions (LMK) 42 Terminal Configurations 8. Power up sequence 9. RF Characteristics Oct. 13. 2016 C P6 P8 P9 P10 P11 P16 P17 4.2. Pin configurations 4.3. Pin mux table 5. LED drive 6. Phototransistor 7. SPI flash requirements 9. Operating condition 10. External 32kHz crystal 14. Reference circuit 15. Recommended components Oct. 20. 2016 D P10 6. Phototransistor Correct imp003 reference Oct. 21. 2016 E P3 1. Scope Update cloud information Mar. 14. 2017 F P5 4.1. Dimensions Correct Pin 1 Marking Apr. 13. 2017 G P5 P12 4. Dimensions, Marking and Terminal Configurations 9. Operating Condition Correct Top view design Correct the range of VDD_WLAN, VDDA_MCU and VDD_IO_MCU Apr. 20. 2017 H P5 4.1. Dimensions Correct the marking. Jun. 27. 2017 I P3 1. Scope Wording Jul. 29. 2017 J P1 P15 P16 P23 P17 P24 P34 Part number 7. SPI flash requirements 8. Required wiring for Bluetooth operation 15. Reference circuit 9. Absolute Maximum Rating 16.3 Flash memory 20. Regulatory Requirements Updated from temp to production part number Added SPI commands Added Bluetooth connections Correction Updated part number recommendations Added FCC and IC regulations for modular certification

Preliminary Specification Number : SP-ZZ1MD-J 2 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. TABLE OF CONTENTS 1. Scope ............................................................................................................................... 3!2. Part Number ..................................................................................................................... 4!3. Block Diagram .................................................................................................................. 5!4. Dimensions, Marking and Terminal Configurations .......................................................... 6!4.1. Dimensions ................................................................................................................ 6!4.2. Terminal Configurations ............................................................................................. 9!4.3. Pin Mux table ........................................................................................................... 12!5. LED drive ........................................................................................................................ 13!6. Phototransistor ............................................................................................................... 14!7. SPI flash requirements ................................................................................................... 15!8. Required wiring for Bluetooth operation ......................................................................... 16!9. Absolute Maximum Rating ............................................................................................. 17!10. Operating Condition ..................................................................................................... 17!11. External 32.768 kHz Crystal ......................................................................................... 18!12. Power Up Sequence .................................................................................................... 19!12.1. Without RESET_L control ...................................................................................... 19!12.2. With RESET_L control ........................................................................................... 19!12.3. RESET_L Circuit .................................................................................................... 20!13. Electrical Characteristics .............................................................................................. 21!14. Land pattern (Top View) ............................................................................................... 22!15. Reference Circuit .......................................................................................................... 23!16. Recommended Components ........................................................................................ 23!16.1. Bi-color LED ........................................................................................................... 23!16.2. Phototransistor ....................................................................................................... 24!16.3. SPI Flash ............................................................................................................... 24!17. Tape and Reel Packing ................................................................................................ 25!18. NOTICE ........................................................................................................................ 28!18.1. Storage Conditions: ............................................................................................... 28!18.2. Handling Conditions: .............................................................................................. 28!18.3. Standard PCB Design (Land Pattern and Dimensions): ........................................ 28!18.4. Notice for Chip Placer: ........................................................................................... 29!18.5. Soldering Conditions: ............................................................................................. 30!18.6. Cleaning: ................................................................................................................ 30!18.7. Operational Environment Conditions: .................................................................... 30!18.8. Input Power Capacity: ............................................................................................ 31!19. PRECONDITION TO USE OUR PRODUCTS ............................................................. 32!20. Regulatory requirements .............................................................................................. 33!20.1. FCC Warning Notice .............................................................................................. 33!20.2. IC Warning Notice .................................................................................................. 34! Please be aware that an important notice concerning availability, standard warranty and use in critical applications of Murata products and disclaimers thereto appears at the end of this specification sheet.

Preliminary Specification Number : SP-ZZ1MD-J 3 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 1. Scope This specification is for the LBEE5ZZ1MD (imp004m) module that provides connectivity to the internet via WiFi. The fully maintained, secure OS that is part of the Electric Imp cloud service comes pre-loaded. • 802.11 b/g/n 1x1 WiFi 802.11b 17dBm (typ.) 802.11g 13dBm (typ.) 802.11n 12dBm (typ.) [20MHz channels] RX Sensitivity -98dBm (typ.) [@1Mbps] On-board antenna Supports WEP, WPA, WPA2, WPS • Bluetooth 4.1 BTLE support for WiFi configuration using GATT Automatically shares antenna with WiFi Optional: requires 4 MCU pins and stack license fee to enable functionality in commercial products • 32-bit Cortex M4 processor - Robust embedded operating system with fail-safe firmware updates - Virtual machine for customer firmware - 256kB of application bytecode flash - Over 190kB of free application RAM • Electric Imp OS & service - Robust embedded operating system with fail-safe, secure OS & Application updates - Pre-provisioned MAC address & per-device secrets - TLS1.2-RSA-ECDHE (forward secrecy) connection to cloud - Elliptic curve challenge-response to prevent device impersonation - Fully featured cloud VM for every device for easy integration with RESTful APIs - Open source integrations with AWS, Azure, etc services • LED drive for red/green status LEDs • Phototransistor input for Electric imp’s patented BlinkUpTM technology for easy configuration from any smartphone, tablet, or web browser • 18 user selectable I/Os - GPIO, PWM, Analog input, SPI, UART, I2C - Dedicated SPI bus for local storage • Low power 14uA (typ.) sleep mode - Option for coin cell RTC battery backup • Compliant with the RoHS directive

Preliminary Specification Number : SP-ZZ1MD-J 4 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 2. Part Number Sample Part Number LBEE5ZZ1MD-TEMP Production Part Number LBEE5ZZ1MD-011

Preliminary Specification Number : SP-ZZ1MD-J 5 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 3. Block Diagram Note: 32.768KHz outside of module

Preliminary Specification Number : SP-ZZ1MD-J 6 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 4. Dimensions, Marking and Terminal Configurations 4.1. Dimensions < Side View > < Top View > < Top View > XXXXXXXXX (F) imp004m(E) (B) (G) electricimp (C) (A) Model:Type1MDR 001-P01018 FCC:VPYLB1MDIMP004 IC :772C-LB1MDIMP004(H) (J) (I) (D)

Preliminary Specification Number : SP-ZZ1MD-J 8 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. Mounting The module is designed to be mounted on the edge of the board, with the antenna section hanging off in free space. The antenna is tuned for free space operation. Please see the design guide on Electric Imp dev center website at http://www.electricimp.com/docs for more information.

Preliminary Specification Number : SP-ZZ1MD-J 9 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 4.2. Terminal Configurations Top view (through package)

Preliminary Specification Number : SP-ZZ1MD-J 10 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. No. Name Type Description 1 GND GND 2 CLK_REQ O Reference clock request. As the clock is internal, this pin does not need to be connected 3 BT_REG_ON I Enable Bluetooth power. Leave NC if Bluetooth is not used (active high) 4 NC - No Connect 5 pinM I/O GPIO, i2cNM SDA, PWM 6 pinN I/O GPIO, i2cNM SCL, PWM 7 pinP I/O GPIO, i2cQP SDA, PWM, IRQ 8 pinW I/O GPIO, uartBCAW CTS, ADC, IRQ & wake from deep sleep (active high) 9 GND GND 10 pinA I/O GPIO, uartBCAW RTS, spiAHSR MOSI, ADC, PWM 11 pinB I/O GPIO, uartBCAW TX, ADC, PWM, IRQ 12 pinC I/O GPIO, uartBCAW RX, ADC, IRQ 13 LPO_IN I Sleep Clock (for both WiFi & Bluetooth). If low power WiFi operation – or Bluetooth operation – is required, this pin should be connected to pinE. Otherwise, ground this pin. 14 pinD I/O GPIO, ADC, PWM, IRQ 15 pinE I/O GPIO, IRQ 16 pinK I/O GPIO, spiGJKL SCLK, ADC, PWM 17 pinL I/O GPIO, spiGJKL NSS, ADC, IRQ 18 GND GND 19 VDD_IO_MCU PWR MCU/WLAN VIO 20 GND GND 21 pinQ I/O GPIO, uartQ TX, i2cQP SCL, IRQ 22 pinR I/O GPIO, spiAHSR NSS, IRQ 23 pinS I/O GPIO, spiAHSR SCLK, IRQ 24 PSU_ENABLE O Active high when WiFi needs 2.7v+ 25 pinF I/O GPIO, uartFGJH TX 26 pinG I/O GPIO, uartFGJH RX, spiGJKL MOSI 27 pinH I/O GPIO, uartFGJH CTS, uartHJ TX, spiAHSR MISO, IRQ 28 pinJ I/O GPIO, uartFGJH RTS, uartHJ RX, spiGJKL MISO, pulse counter 29 GND GND 30 LED_RED O Red LED drive 31 LED_GREEN O Green LED drive 32 OPTO_IN I Phototransistor input 33 OPTO_BIAS O Phototransistor supply 34 FLASH_MOSI O SPI flash connection 35 FLASH_SCLK O SPI flash connection 36 FLASH_CS_L O SPI flash connection

Preliminary Specification Number : SP-ZZ1MD-J 11 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 37 FLASH_MISO I SPI flash connection 38 NC - 39 RESET_L I MCU reset, internally pulled up 40 VSSA/VREF- GND Must be connected to GND 41 OSC32_OUT O 32kHz xtal connection 42 OSC32_IN I 32kHz xtal connection (ground if no xtal fitted) 43 GND GND 44 VBAT_MCU PWR MCU VBAT input 45 VDDA_MCU PWR MCU VDDA input 46 VDD_WLAN PWR WLAN VBAT input 47-70 GND GND 71 BT_UART_TXD O Bluetooth UART transmit. Leave NC if not used 72 BT_UART_RTS O Bluetooth UART ready to send. Leave NC if not used 73 BT_UART_RXD I Bluetooth UART receive. Leave NC if not used 74 BT_UART_CTS I Bluetooth UART clear to send. Leave NC if not used 75-76 GND GND 77 BT_HOST_WAKE O Signal to wake host (from Bluetooth core). Leave NC if not used 78-81 NC - 82 BT_DEV_WAKE I Signal to wake Bluetooth core (from host). Leave NC if not used 83 NC - No Connect 84-103 GND GND 104 NC - Note this pad should not be touching any PCB

Preliminary Specification Number : SP-ZZ1MD-J 12 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 4.3. Pin Mux table Pin Uart BCAW uart FGJH uart HJ uart Q i2c NM i2c QP spi AHSR spi GJKL ADC PWM Pulse count State change pinA RTS MOSI Yes Yes pinB TX Yes Yes Yes pinC RX Yes Yes pinD Yes Yes Yes pinE Yes pinF TX pinG RX MOSI pinH CTS TX MISO Yes pinJ RTS RX MISO Yes pinK SCLK Yes Yes pinL NSS Yes Yes pinM SDA Yes pinN SCL Yes pinP SDA Yes Yes pinQ TX SCL Yes pinR NSS Yes pinS SCLK Yes pinW CTS Yes Yes

Preliminary Specification Number : SP-ZZ1MD-J 13 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 5. LED drive The indicator LED should be bicolor, because red, green and amber (red+green) are used to indicate status. The LED drive pins will auto-detect common anode or common cathode parts. The detection is done by looking to see which way up the LED_RED pin is idling at boot; to ensure this works correctly, please place a 10k resistor in parallel with the red LED. The current drive on these pins is 20mA maximum. Please refer to section 15 for the recommended LEDs. <Common anode diagram> <Common cathode diagram> Two specific LED codes indicate errors when talking to the SPI flash: SPI flash not found SPI flash error If you encounter either of these codes, then this indicates an electrical connection issue or an incompatible flash part.

Preliminary Specification Number : SP-ZZ1MD-J 14 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 6. Phototransistor The phototransistor is used to receive BlinkUp configuration data. The bias resistor connected between OPTO_IN and GND may need to be adjusted to ensure adequate sensitivity and response time - in general you need at least 500mV swing on the OPTO_IN pin between black and white states, with the worst (dimmest) BlinkUp sender you can find. More information and sample code to tune blinkup is available on the Electric Imp dev center website. End-user BlinkUp send data at between 30 and 60 bits per second, depending on the user’s device. For factory configuration, data is typically sent at 142 bits per second using red LED(s) in a test fixture. If your application does not require optical configuration, config can be sent electrically at 142 bits per second from another micro using the OPTO_IN pin. Please contact us for more details. It is also recommended to place 0402, 13pF capacitor footprints (Murata GRM1555C1H130JA01) close to the imp004m between OPTO_BIAS and GND, and OPTO_IN and GND. If issues are seen with RF coupling onto the blinkup circuit, then these components will address the issue by presenting a low impedance in the 2.4GHz band. Please refer to paragraph 15 for the recommended phototransistors.

Preliminary Specification Number : SP-ZZ1MD-J 15 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 7. SPI flash requirements An external SPI Flash part is required for operation, which must be pre-loaded with the correct WiFi firmware image before assembly. The required image is available from the Electric Imp dev center website at http://www.electricimp.com/docs The minimum size of the SPI Flash is 8Mbit (1MB), and the maximum size is 128Mbit (16MB). The area below address 0xC2000 (776kB) is the pre-programmed area. The remainder of the flash device is made available to user code programmatically, and may optionally be pre-programmed for user applications before assembly. The imp004m’s SPI flash chip must support both 4KB erases (Command 0x20) and 64KB erases (command 0xD8) and Page Program (command 0x02). You must also ensure that the SPI flash you use is able to run down to the minimum operational voltage of your product to ensure that the SPI flash is operational at all times that the imp is operational. This is critical during upgrades in low battery states. If you are running from a single LiMnO2 cell (eg. CR123), you should use a wide voltage range SPI flash that is operational from 1.7-3.6V such as the Macronix MX25R8035FM2IH0. Minimum Size 8 Mbit (1024 kByte) Reserved for OS (do not pre-program) 0x000000 to 0xC2000 (776 kByte) Summary of required SPI flash commands Required Command Command in Hex 4KB Sector Erase 0x20 64KB Block Erase 0xD8 Page Program 0x02

Preliminary Specification Number : SP-ZZ1MD-J 16 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 8. Required wiring for Bluetooth operation If Bluetooth is not used in the application, leave all Bluetooth pins (3, 71-74, 77, 82) unconnected. To use Bluetooth in an application, you must connect the MCU pins to the Bluetooth device: • BT_UART_TXD should be connected to an MCU UART RX pin (pinC, pinG or pinJ) • BT_UART_RXD should be connected to the same UART’s TX pin (pinB, pinF or pinH) • pinE MUST be connected to the LPO in pin, to supply a 32kHz clock to the Bluetooth radio • BT_REG_ON should be connected to any free MCU pin, to control Bluetooth power • BT_UART_CTS should be grounded (The imp Bluetooth stack uses 2 wire UART) Aside from pinE, which cannot be reassigned, choice of UART and control pin for BT_REG_ON is determined by the application – this allows flexibility in complex IO configurations. Please refer to the Electric Imp dev center for more information on how to configure the Bluetooth stack, which is present from impOS release 40. Note that though use of Bluetooth is free for developers, commercial use incurs an additional licensing fee for the stack. Please contact sales@electricimp.com for more details.

Preliminary Specification Number : SP-ZZ1MD-J 17 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 9. Absolute Maximum Rating min. max. unit Storage Temperature -40 85 deg.C Supply Voltage VBAT_MCU -0.3 4 V VDDA_MCU -0.3 4 VDD_WLAN -0.5 6 VDD_IO_MCU -0.3 3.63 Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters is set within operating condition. 10. Operating Condition min. typ. max. unit Operating Temperature Range -30 25 70 deg.C Specification Temperature Range -20 25 55 deg.C Supply Voltage VBAT_MCU 1.65 3.3 3.6 V VDDA_MCU 1.8 3.3 3.6 VDD_WLAN 3.0 3.3 3.6 VDD_IO_MCU 1.8 3.3 3.6 Notes : n All RF characteristics in this datasheet are defined by Specification Temperature Range. Specifications require derating at extreme temperatures. n VDDA_MCU and VDD_IO_MCU must be the same potential.

Preliminary Specification Number : SP-ZZ1MD-J 18 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 11. External 32.768 kHz Crystal If the application requires the imp004m to enter deep sleep mode, a 32kHz crystal should be attached to the OSC32_IN and OSC32_OUT pins. Please refer to the STM32F412 datasheet and application note AN2867 by STMicroelectronics NV for detailed crystal requirements. If deep sleep mode is not required, OSC32_IN should be connected to GND and OSC32_OUT left floating. The imp004m will detect this state and disable the sleep APIs.

Preliminary Specification Number : SP-ZZ1MD-J 19 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12. Power Up Sequence 12.1. Without RESET_L control Following timing diagram explain module power up sequence. *Power down sequence is opposite sequence of power up. 12.2. With RESET_L control *Power down sequence is opposite sequence of power up. *RESET_L pin must be controlled by Open Drain. VBAT_MCU Ramp time 90% > 40µs VDD_WLAN VDDA_MCU Timing same as VBAT_MCU VDD_IO_MCU VBAT_MCU Ramp time 90% > 40µs VDD_WLAN VDDA_MCU Timing same as VBAT_MCU VDD_IO_MCU RESET_L Timing of deassertioRESET_L signal same as VDD_IO Timing same as VBAT_MCU Timing same as VBAT_MCU Timing same as VBAT_MCU Timing same as VBAT_MCU

Preliminary Specification Number : SP-ZZ1MD-J 20 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 12.3. RESET_L Circuit (1) The reset network protects the device against parasitic resets. (2) The use must ensure that the level on the RESET_L pin can go below the VIL(NRST) max level specified in below table. Otherwise the reset is not taken into account by the device. (3) RESET_L pin must be controlled by Open Drain. High signal must not input to this pin. Symbol Parameter Min Typ Max Unit VIL RESET_L I/O input low level voltage - - 0.1xVDD_IO_MCU+0.1 V Filter Internal Reset V DD_IO_MCU (3) 40kΩ RESET_L (2 ) External Reset circuit (1) Murata Module 0.1uF

Preliminary Specification Number : SP-ZZ1MD-J 21 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 13. Electrical Characteristics - DC Characteristics - min. typ. max. unit 1. DC current 1) Tx mode1) 300 370 mA 2) Rx mode 45 100 mA 1) Conditions: 25deg.C, VDD_WLAN=3.3V, VDD_IO_MCU=3.3V (1Mbps mode unless otherwise specified.) Note: The above mentioned values have been obtained according to our own measuring methods and may very depend on the circuit, in which the component is actually incorporated. Therefore, you are kindly requested to test the performance of the component actually in your set.

Preliminary Specification Number : SP-ZZ1MD-J 22 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 14. Land pattern (Top View) Unit : mm

Preliminary Specification Number : SP-ZZ1MD-J 23 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 15. Reference Circuit 16. Recommended Components 16.1. Bi-color LED Manufacturer Manufacturer’s part number Surface mount top-view SunLED XZMDKVG59W-1 Liteon LTST-C195KGJRKT side-view SunLED XZMDKVG88W Bivar SM1204BC Through-hole 3mm SunLED XLMDKVG34M Liteon LTL1BEKVJNN

Preliminary Specification Number : SP-ZZ1MD-J 24 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 16.2. Phototransistor Manufacturer Manufacturer’s part number Surface mount top-view Everlight PT17-21C/L41/TR8 Fairchild KDT00030TR side-view SunLED XZRNI56W-1 Everlight PT12-21C/TR8 Through-hole 3mm SunLED XRNI30W-1 LiteOn LTR-4206 16.3. SPI Flash Size Manufacturer Manufacturer’s part number 8 Mbit Adesto Technologies Macronix International AT25SF081 MX25R8035F(1) 16 Mbit Adesto Technologies Cypress Semiconductor Corp AT25SF161 S25FL116K(2) 32 Mbit Adesto Technologies Cypress Semiconductor Corp AT25SF321 S25FL132K(2) 64 Mbit Cypress Semiconductor Corp Cypress Semiconductor Corp S25FL064L S25FL164K(2) (1) This device offers a wide operating voltage range (2) This part is EOL, though inventory may still be available through distributors

Preliminary Specification Number : SP-ZZ1MD-J 25 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 17. Tape and Reel Packing (1) Dimensions of Tape (Plastic tape) *1 Cumulative tolerance of max. ± 0.3 every 10 pitches *2 Reference value  (Unit : mm) (2) Dimensions of Reel (Unit: mm) 2.0± 0.15 0.3± 0.05 24.0± 0.1 1.5+0.1/-0.0 2.0+0.1/-0.0 4 .0± 0.1*1 22.00±0.10*2 . 18.00± 0.10 2.55±0.1 44.0±0.3 40.4±0.1 20.2±0.1 1.75±0.1 (f 100)f 21±0.82.0±0.545.5(f 330)50.5max

Preliminary Specification Number : SP-ZZ1MD-J 26 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. (3) Taping Diagrams [1] Feeding Hole : As specified in (1) [2] Hole for chip : As specified in (1) [3] Cover tape : 62μm in thickness [4] Base tape : As specified in (1) (4) Leader and Tail tape Tail tape (No components) Components No components 200mm min. Leader tape (Cover tape alone) Feeding direction Chip Feeding Direction

Preliminary Specification Number : SP-ZZ1MD-J 27 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. (5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled toward the user. (6) The cover tape and the base tape are not adhered at no components area for 250mm min. (7) Tear off strength against pulling of cover tape : 5N min. (8) Packaging unit: 500pcs./ reel (9) Material: Base tape : Plastic Reel : Plastic Cover tape, cavity tape and reel are made the anti-static processing. (10) Peeling of force: 1.1N max. in the direction of peeling as shown below. (11) Packaging (Humidity proof Packing) Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant and the humidity indicator. 165 to 180 °1.1 N max.Base tape Cover tape 　湿度インジケ－タ乾燥剤表示ラべル防湿梱包袋表示ラベルLabel Label Desiccant Humidity Indicator Anti-humidity Plastic Bag

Preliminary Specification Number : SP-ZZ1MD-J 28 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 18. NOTICE 18.1. Storage Conditions: Please use this product within 6month after receipt. - The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperature over 40deg.C.) - The product left more than 6months after reception, it needs to be confirmed the solderability before used. - The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.). - Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp object and dropping the product, shall not be applied in order not to damage the packing materials. This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020) - After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be used within 168hours. - When the color of the indicator in the packing changed, the product shall be baked before soldering. Baking condition: 125+5/-0deg.C, 24hours, 1time The products shall be baked on the heat-resistant tray because the material (Base Tape, Reel Tape and Cover Tape) are not heat-resistant. 18.2. Handling Conditions: Be careful in handling or transporting products because excessive stress or mechanical shock may break products. Handle with care if products may have cracks or damages on their terminals, the characteristics of products may change. Do not touch products with bear hands that may result in poor solder ability and destroy by static electrical charge. 18.3. Standard PCB Design (Land Pattern and Dimensions): All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Murata beforehand.

Preliminary Specification Number : SP-ZZ1MD-J 29 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 18.4. Notice for Chip Placer: When placing products on the PCB, products may be stressed and broken by uneven forces from a worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to follow the specifications for the maintenance of the chip placer being used. For the positioning of products on the PCB, be aware that mechanical chucking may damage products.

Preliminary Specification Number : SP-ZZ1MD-J 30 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 18.5. Soldering Conditions: The recommendation conditions of soldering are as in the following figure. When products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 °C. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 °C. Contact Murata before use if concerning other soldering conditions. Reflow soldering standard conditions(Example) Please use the reflow within 2 times. Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less. 18.6. Cleaning: Since this Product is Moisture Sensitive, any cleaning is not permitted. 18.7. Operational Environment Conditions: Products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur. - In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx etc.). - In an atmosphere containing combustible and volatile gases. - Dusty place. - Direct sunlight place. - Water splashing place. - Humid place where water condenses. - Freezing place. If there are possibilities for products to be used under the preceding clause, consult with Murata before actual use. As it might be a cause of degradation or destruction to apply static electricity to products, do not apply static electricity or excessive voltage while assembling and measuring. Within 120s Pre-heating time(s) 220 deg.C Within 60s Cooling down Slowly 180 deg.C 150 deg.C 240to 250 deg.C Within 3s

Preliminary Specification Number : SP-ZZ1MD-J 31 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 18.8. Input Power Capacity: Products shall be used in the input power capacity as specified in this specifications. Inform Murata beforehand, in case that the components are used beyond such input power capacity range.

Preliminary Specification Number : SP-ZZ1MD-J 32 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 19. PRECONDITION TO USE OUR PRODUCTS PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS. Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications of our product when our product is mounted to your product. All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment specified in this specification. You are requested not to use our product deviating from the condition and the environment specified in this specification. Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this specification. WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. The product shall not be used in any application listed below which requires especially high reliability for the prevention of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements. Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS, DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS. - Aircraft equipment.- Aerospace equipment- Undersea equipment. - Power plant control equipment- Medical equipment. - Transportation equipment (vehicles, trains, ships, elevator, etc.). - Traffic signal equipment. - Disaster prevention / crime prevention equipment. -Burning / explosion control equipment - Application of similar complexity and/ or reliability requirements to the applications listed in the above. We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the regulations and laws in the world. We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in which our products or services are used. Information provided by us regarding third-party products or services does not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from us under our patents or other intellectual property. Please do not use our products, our technical information and other data provided by us for the purpose of developing of mass-destruction weapons and the purpose of military use. Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations", etc. Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials and/or components from our suppliers. By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your company and that you understand and accept the validity of the contents herein. When you are not able to return the signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to their development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability for damages caused by - the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the product to be sold by you, -deviation or lapse in function of engineering sample, -improper use of engineering samples. We disclaim any liability for consequential and incidental damages. If you can’t agree the above contents, you should inquire our sales.

Preliminary Specification Number : SP-ZZ1MD-J 33 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 20. Regulatory requirements If the OEM or system integrator incorporates the 1MD module into their final product and wishes to reuse the 1MD module’s FCC certification, it is the OEM/system integrator’s responsibility to ensure compliance is met on production units. 20.1. FCC Warning Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Information to Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with “Contains FCC ID: VPYLB1MDIMP004. This imp004m module is to be used only for mobile and fixed application. In order to re-use the imp004m module FCC approvals, the antenna must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located with any other antenna or transmitter. If the module is installed with a separation distance of less than 20cm from all person or is co-located or operating in conjunction with any other antenna or transmitter then additional FCC testing and certification may be required. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. OEM integrators must ensure that the end user has no manual instructions to remove or install the imp004m module.

Preliminary Specification Number : SP-ZZ1MD-J 34 / 34 Preliminary < Specification may be changed by Murata without notice > Murata Manufacturing Co., Ltd. 20.2. IC Warning Notice This device complies with Industry Canada license-exempt RSS standard(s). a. Common information Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme à la norme(normes) RSS exempte de licence d'Industrie Canada a. Informations communes Son fonctionnement est soumis aux deux conditions suivantes: 1. Ce dispositive ne peut causer des interferences, et 2. Ce dispositive doit accepter toute interference, y compris les interferences qui peuvent causer un mauvais fonctionnement du dispositive. Information to Be Supplied to the End User by the OEM or Integrator Modular information form OEM Information to be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with “Contains IC: 772C-LB1MDIMP004” This imp004m module is to be used only for mobile and fixed application. In order to re-use the imp004m module IC approvals, the antenna(s) used in this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. If antenna is installed with a separation distance of less than 20cm from all person or is co-located or operating in conjunction with any other antenna or transmitter then additional IC testing and certification may be required. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. OEM integrators must ensure that the end user has no manual instructions to remove or install the imp004m module.

Navigation menu