Murata LB1PR Bluetooth mesh node User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3877217
Application ID	wRlnDSnYtyqTfpVj5sj/MQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.01kB (287631 bits)
Date Submitted	2018-06-05 00:00:00
Date Available	2018-06-11 00:00:00
Creation Date	2018-05-17 13:05:46
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-05-17 13:06:22
Document Title	User Manual
Document Creator	Word 用 Acrobat PDFMaker 18
Document Author:	Eigo Shimakura

Murata Bluetooth mesh Node
Installation Guide
Shipped Components

Murata Bluetooth mesh Node (LBCC2ZZ1PR)

Locknut
Page 1
1PR-IG Rev. 1
Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
Caution
Installation and maintenance must be done in accordance with local, state and national electrical codes
(NEC) and requirements.
Bluetooth mesh Node Installation
Step
Description
Make sure the luminaire is de-energized.
Determine the location for the Bluetooth mesh Node in
Figure
the luminaire and make a 7/8 inch (23 mm) diameter hole
in the luminaire.
Insert the Bluetooth mesh Node through the hole.
Use the locknut from the rear of the sensor to fix the
Bluetooth mesh Node.
Connect the Bluetooth mesh Node with a compatible LED
driver in accordance with Wiring Diagram and Terminal
Assignment.
Install the luminaire on the ceiling and energize it.
Page 2
1PR-IG Rev. 1
Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
Wiring Diagram
Auxiliary 12 VDC supply from LED Driver
DC+
DC-
Non-AUX
LED Driver
(To LEDs)
Dim+
Dim-
……
DC+
DC-
Non-AUX
LED Driver
(To LEDs)
Dim+
Dim-
DC+
DC-
AUX
LED Driver
(To LEDs)
Dim+
Dim-
AWG 24-18
(strip 7-9mm)
12V
GND
External Power Supply
DC+
DC-
Non-AUX
LED Driver
(To LEDs)
Dim+
Dim-
External
Power Supply
12V
GND
AWG 24-18
(strip 7-9mm)
Page 3
1PR-IG Rev. 1
Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
Terminal Assignment
DIM-
DIM+
12VDC
GND
DIM +
12VDC
DIM -
GND
LED Indicators
Green LED (Network Status)
Fast blink (300ms cycle)
Unprovisioned
Slow blink (2000ms cycle)
Provisioned
Blink twice
Mesh packet received
Long blink
Factory reset
Red LED (Motion Sensor Status)
Blink once
Motion detected
General Information
Model No.
LBCC2ZZ1PR
FCC ID
VPYLB1PR
IC
772C-LB1PR
Page 4
1PR-IG Rev. 1
Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
FCC and Industry Canada Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Please note that changes or
modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following
two conditions: (1) This device may not cause interference; and (2) This device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire
de brouillage; (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
Page 5
1PR-IG Rev. 1
Copyright © Murata Manufacturing Co., Ltd. All rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Eigo Shimakura
Company                         : 株式会社　村田製作所
Create Date                     : 2018:05:17 13:05:46+09:00
Modify Date                     : 2018:05:17 13:06:22+09:00
Source Modified                 : D:20180517040511
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2018:05:17 13:06:22+09:00
Creator Tool                    : Word 用 Acrobat PDFMaker 18
Document ID                     : uuid:72ba842f-4984-4472-81a9-8317a50bdee8
Instance ID                     : uuid:af0a970f-43ea-49d3-bfd5-c57cd5dc40b7
Subject                         : 4
Format                          : application/pdf
Creator                         : Eigo Shimakura
Producer                        : Adobe PDF Library 15.0
Page Layout                     : OneColumn
Page Count                      : 5

EXIF Metadata provided by EXIF.tools