Mustek Systems MBTH120 BT-DH User Manual BT Headset En indd

Mustek Systems Inc BT-DH BT Headset En indd

Users Manual

Quick GuideHeadsetEN FIRUGRPLTUDKSWPTNLESITFRDE TC
Model No.: MBT-H120FCC ID: HWF-MBTH120This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifi cations not expressly approved by the party responsible for com-pliance could void the authority to operate equipment.Tested To Comply With FCC StandardsFOR HOME OR OFFICE USEBLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED
3BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED EN12345678Identifying the Parts1. Volume Up / Pairing Button 2. Power / Talking Button3. Volume Down 4. Indicator LED Red : Power Off Blue : Power On Red+Blue : Pairing mode5. Earhook6. Earphone7. Microphone8. DC-IN jack
BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED 4Charging the BatteryFirst time use:Please charge the built-in Li-ion bat-tery for 24 hours before the initial use. Low battery:When the battery is low, the indicator LED will fl ash red. Please charge the battery for approximately 2.5 hours. How to charge:1. Connect one end of the supplied AC Adapter (5V/0.5A) to the DC IN jack on the headset and the other end to the wall outlet. The indicator LED will light red when charging. After fully charging the battery, the indicator LED will light out.Remove the AC Adapter from the DC IN jack of the headset and the wall outlet.
Wearing the HeadsetTo wear on your right ear: Reverse the earhook to change its direction, and then follow the steps above to wear it on your right ear. (Figure 1) (Figure 2)5BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED Wearing the HeadsetENYou can wear the headset on either ear with the reversible earhook.To wear on your left ear: Wear the headset vertically on your left ear. (Please refer to Figure 1) Rotate the headset toward the rear of your ear and point the microphone toward your mouth. (Please refer to Figure 2)
6BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED To power your headset on:Press the Power button for approxi-mately 2 seconds until the indicator LED starts to fl ash blue. Then you can start to operate your headset.To power your headset off:Press the Power button for approxi-mately 2 seconds until the indicator LED starts to fl ash red. Once the indicator LED stops fl ashing, the power is OFF.Powering the Headset On or Off
7BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED ENPairing with a Bluetooth Phone and blue alternately, and enters the pairing mode.3. Search for Bluetooth devices by following the phone’s operating instruction.4. Select “MBT-H120” from the searched devices list and confi rm it.Enter the passkey “1234” and confi rm it.After fi nishing the pairing process, the indicator LED will fl ash blue.( Notes: 1) The operable range without obstructions is up to 10 meters (approximately 33 feet) between your headset and the Bluetooth devices.2) Your headset can save the pairing infor- mation of up to 8 phones, but connect to only one phone at a time. Before operating your headset with a Bluetooth phone, you must execute “Pairing” process to create a link between the devices. To pair with a Bluetooth phone, please follow the instruction below:Ensure the headset is ON and enters the standby mode with fl ashing blue LED once rapidly every 3 seconds. ( Note: When powered on, the headset will attempt to connect to an available Bluetooth device. Please press the Power button to switch to the standby mode. )2. Press the Volume Up button for approximately 4 seconds until the indicator LED starts to fl ash red
8BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED If you have entered the passkey without previously pairing with another phone, the phone will be the “default phone” for your headset. If you want to use another Bluetooth phone with your headset, please switch the headset off, then disconnect it from the previous phone. Next, pair with another phone once restarted as described in page 7. )Pairing with a Bluetooth Phone-continue
9BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED ENCall Functions the voice tag through your headset’s microphone.4) After recognizing the correct voice tag, the phone number will be dialed automatically.( Note: This feature is only available with a phone that supports the ‘Voice Dialing’ function. For details, please refer to your phone’s user guide. )To redial the last call:1. Press the Volume Down button for approximately 2 seconds when no call is in progress.To reject a call:1. Press the Power button for approximately 2 seconds to reject an incoming call.To answer or end a call:When receiving a call, you will hear a ring tone through the headset’s ear-phone. Press the Power/Talk button to answer or end a call. To make a call:There are two ways to make a call:1. Using your phone’s keypad: Press the Number button you want to call in your phone’s keypad to make a call.2. Using the “Voice Dialing” function through your headset:1) Record “Voice Tags” in your phone address book in advance.2) Ensure this function is ON.3) Press the Talk button, then say
1010BLUETOOTH HEADSET GETTING STARTEDBLUETOOTH HEADSET GETTING STARTED While plugging in the charger:Headset Indicator LEDIndicator LED Headset Light Red ChargingLight Out Full ChargeWhile unplugging the charger:Indicator LED HeadsetFlash Red Low BatteryFlash Red Light Out Power OffFlash Blue Power OnFlash Red and Blue Alternately Pairing ModeFlash Blue LED once rapidly every 3 seconds Signal Available(Standby Mode)Flash Blue LED twice rapidly every 3 seconds ConnectingFlash Blue LED 3 times rapidly every 3 seconds ConnectedFlash Blue LED 4 times rapidly every 3 seconds Connected (On a Call)

Navigation menu