User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2122169 |
| Application ID | 1FFdxegfLlpU0q7PUUKdyg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 479.9kB (5998780 bits) |
| Date Submitted | 2013-11-19 00:00:00 |
| Date Available | 2013-11-19 00:00:00 |
| Creation Date | 2013-07-25 12:27:41 |
| Producing Software | PDF Architect |
| Document Lastmod | 2013-07-30 12:52:01 |
| Document Title | User Manual |
| Document Creator | PDF Architect |
| Document Author: | Ronya |
MDB Peripheral Cables P/N: 3108 MDB Peripheral Adaptor Cable P/N: 3113 MDB Peripheral Adaptor Cable P/N: 3111 MDB Peripheral Adaptor Cable P/N: 3109 MDB Peripheral Adaptor Cable For MEI CF690 Coin Mechanism For CoinCo - Global 2 Coin Mechanism For MEI CF7xxx Series Coin Mechanism For MEI CF694 Coin Mechanism DEX Adaptor Cables P/N: 3118 DEX Adaptor Cable P/N: 3110 DEX Adaptor Cable For Jofemar Machines For MEI CF690/CF694 Coin Mechanism Additional Adaptors P/N: 3105 Cashless Adaptor Cable P/N: 3116 Adaptor Cable For : For Jofemar Machines Pulse / Door Switch / Temperature Probe P/N: 3107 Dual Reader Adaptor Cable P/N: 3107 Dual Reader Adaptor www.nayaxvend.com Installation Guide Prior to installation make sure you perform the following: 1. Check machine model and protocol: - With MDB Protocol the connection is between the VMC and the coinmech - Executive Protocol requires MDB Peripheral cable (see separate installation instructions) - Mechanical Protocol requires MDB Peripheral cable and 12v DC Power Adaptor (see separate installation instructions) 2. Check that the machine software supports card readers 3. Make sure the cable length is sufficient when choosing the installation position 4. Check for DEX plug or DDCMP connector 5. Check that all parts of cashless unit are present (Wireless module, Bezel, MDB Cable, Antenna) 6. Make sure machine power is off Card Reader – internal installation (Bill acceptor window): - Locate and remove window cover - Place the Card Reader from within the vending machin - Fasten it with nuts - Remove the back plate of the Card Reader by unscrewing the 4 bolts - Locate a place on the external wall for the Card Reader - Make sure the reader’s location will allow a successful card swipe - Use back plate as a stencil to mark the 5 holes for drilling - Use #4 drill bit to drill the 5 marked holes - Use a cone shaped drill to widen the center hole P/N: 2103 - Thread cables in the center hole - Fasten Card Reader to machine with the 4 bolts that held the back plate Must be placed in a visible location with clear access to the buttons, Make sure that the module position will not interfere with normal operation of the machine: - Do NOT place module in a damp or refrigerated area - Do NOT place module in a hot area (engine etc.) - Do NOT expose module to outside moisture (e.g. rain) - Place module with easy access to it in case part replacement is necessary. Antenna (Magnetic mount) P/N: 3103 1. Connect Bezel cables to Wireless module: - LCD RJ45 connector #10 to LCD RJ45 Plug #1 - Card Reader white Molex #9 to Card Reader 5 pin Molex Connector #2 - Speaker 3.5mm Jack #11 to 3.5mm Audio Plug #3 2. Connect Antenna to Wireless module: - SMA Screw on Connector #18 to SMA Screw on Connector #4 3. Connect MDB Cable to Vending Machine Controller*(VMC) and Coin Mech. : - Connect DB15 Comm. & Power Male Connector #17 to DB15 Comm. & Power Female Connector #5 - Sever Connection Between VMC and Coin Mech. - MDB Male Molex #12 to VMCs MDB female Molex - Coin Mech. MDB Male Molex to MDB female Molex #13 - DEX 1/4 inch male Jack #15 to VMCs DEX 1/4 female plug Connect to VMC MDB cable Connect to Coinmech MDB cable DEX cable male jack Connect to Machine DEX port 18 19 9 10 11 12 13 14 15 16 17 19 8 Pin Molex for Connection of the Pulse / Door Switch / Temperature Probe Adaptor cable Wireless Module MDB Cable - Gray Comm & Power P/N: 2101 Card Reader – External Installation (Bill acceptor present or no acceptor window): - Locate internally avoid vandalism - Locate externally to increase signal strength - Make sure antenna is not surrounded by metal (reception loss) - Make sure the antenna cord is not damaged or pinched when the door is closed Cable Connections P/N: 3101 P/N: 3102 Operating and Testing 1. Turn machine On - Make sure products are present before the vend test - Make sure prices are setup before the vend test - Make sure door switch does not inhibit the machine's work state 2. Once Machine is powered up, a system Self-Test is automatically initiated, performing: - SIM Card check - GPRS Communication check - Server Connectivity check 3. Once the LCD displays "Swipe Card / Dial" - Swipe card for testing purposes. "Sound" and "Communication" check is performed. 4. Carry out trial purchases using the following methods: - A Cash Purchase – check that charge price was correct - A Credit Card Purchase - check that charge price was correct - A Card Vend Cancel – check that credit is not retained on transaction cancel Once all purchases are successfully completed the unit is fully installed and ready for use!
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:07:25 12:27:41+03:00 Creator Tool : PDF Architect Modify Date : 2013:07:30 12:52:01+03:00 Metadata Date : 2013:07:30 12:52:01+03:00 Format : application/pdf Creator : Ronya Producer : PDF Architect Document ID : uuid:6ad3896e-4cce-463a-865d-baf1f2dd8a62 Instance ID : uuid:5139f5be-8d77-4e47-bdbb-1ae34ee29bdb Page Count : 3 Author : RonyaEXIF Metadata provided by EXIF.tools