NEAT Electronics 1123001 Wireless Wall Push and Pear Button User Manual WALL Family

NEAT Electronics AB Wireless Wall Push and Pear Button WALL Family

WALL Family (3PUSH+PEAR) - User Manual

Wall mounted I/O unitUser manualWALL FamilyNE41 12005-02 v2.0
2 WALL Family User manual NE41 12005- 02 v2.0Informaon in this User manual is subject to change without noce.NEAT Electronics AB reserves the right to change or improve their products and to make changes to the content without obligaon to nofy any person or organizaon of such changes or improvements.NEAT Electronics AB is not responsible for any loss of data, income or any consequenal damage whatsoever caused.For more informaon, details and descripons, visit our web site:www. neat-group.com© NEAT Electronics AB 2015All rights reserved.Document number: NE41 12005-02 v2.0Revision date: 2016-03-03NEAT Electronics AB Varuvägen 2 SE-24642 Löddeköpinge SwedenPhone:+46 (0)46 707065Fax: +46 (0)46 707087EU NotesNEAT Electronics declares that this mobile device, type WALL Family, is in compliance with the essenal requirements and other relevant provisions:Direcve: 1999/5/CE (RTTE), 2004/108/EC (EMC), 2006/95/EC (LVD)Standards: EMC: EN 301 489-1 V1.8.1 (2008) EN 301 489-3 V1.4.1 (2002)Radio: EN 300 220-2 V2.3.1 Category IIILow Voltage: EN 60950-1:2006+A11:2010US NotesFCC ID: 2AGLF1123001Changes or modicaons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increasetheseparaonbetweentheequipmentand receiver.• Connecttheequipmentintoanoutletonacircuit dierentfromthattowhichthereceiverisconnected.• Consult the dealer or an experienced radio/TV technician forhelp.Ulrik Lundberg Managing director
3WALL Family User manual NE41 12005- 02 v2.0About WALL Family products 3Product variants 4Hardware overview 4Front overview 4Back overview 4The screw connector 5Power 5Inputs IN1 and IN2 5Outputs OUT1 and OUT2 5Jumpers J1 and J2 6Buons and LEDs 6Ports 1 and 2 6Manual conguraon 7Remove a transmier 9WALL family Programmer 9More informaon 9Important! 9Care and maintenance 9Safety Notes 9Disposal 10Technical data 11About WALL Family productsThe WALL Family consist of 11 prod-ucts divided into two categories, WIOR and ROOM categories, each with a dierent hardware setup to accomodate special needs and requests. The terms WALL, WALL units and WALL family all refer to a common denominaon for all 11 products.The products are equipped with dierent connectors for dierent funcons:• A key cylinder to lock/unlock the unit from operaon.• Pull cord to trig alarms by pulling the aached string• Push buon(s) to trig alarms• 6.35 mm tele jack for e.g. a pear buonContents
4 WALL Family User manual NE41 12005- 02 v2.0Product variantsProduct Buon ConnectorWIOR Category productsWIOR - -KEY - Key cylinderPULL - Pull cordPEAR - 6.35 mm tele jackPUSH x 1 -PUSH+PEAR x 1 6.35 mm tele jackPUSH+PULL x 1 Pull cord3PUSH x 33PUSH+PEAR x 3 6.35 mm tele jackROOM Category productsROOM x 3 -ROOM+PEAR x 3 6.35 mm tele jackHardware overviewFront overviewThe front basically consist of a plasc cover with one or three LEDs and a combinaon of buons and connec-tors (examples below).The unit is designed to t in an inset coupling box with cc 60 mm. To mount directly on a wall, an oponal mounng frame must be ed.PUSH+PEAR ROOM+PEAR/ 3PUSH+PEARBack overviewOn the back are the connectors and contacts.1452 36
5WALL Family User manual NE41 12005- 02 v2.0Item Denominaon①Place for 6.35 mm tele jack connector/Pull cord/Key cylinder② Jumper J2③ Jumper J1④ AAA-baery connectors⑤ Screw connector⑥ Product (data) labelThe screw connectorThe screw connector allows for con-necng external power, inputs and outputs by cable to the WALL unit.10-28 VDCPowerThe unit can be powered either by 10-28VDC or 2 x AAA baeries.Inputs IN1 and IN2In the screw connector there are two wired inputs, IN1 (pin 6) and IN2 (pin 5). Both inputs have a common ground (pin 7) and must be con-nected to potenal free contacts.Input acvaon is ignored during the rst 10 seconds aer start up.Outputs OUT1 and OUT2The outputs are galvanically sepa-rated from the wired inputs and each other and works according to below.ROOM and ROOM+PEARThe relay outputs acts according to the sengs in the builn aconplan or by a superior system (by radio).
6 WALL Family User manual NE41 12005- 02 v2.0The builn aconplan acvates the outputs as below.Mode OUT1 OUT2Standby - -Alarm Acve -Presence - AcveAssistance Acve AcveAll other productsThe relay outputs acts according to sengs made by manual congura-on or by a superior system (by radio).Jumpers J1 and J2As default the jumpers J1 and J2 has the funcons as described below.Mounted Not mountedJ1 Receiver on, 24V mode1Receiver o, baery modeJ2 Inputs (IN1 and IN2) normally closed2Inputs (IN 1 and IN2) normally open21If Jumper J1 is mounted the unit must be externally powered.2IN1 for ROOM and ROOM+PEAR is always normally open.However, jumper J2 can be overrided by using WALL family Programmer (except for ROOM and ROOM+PEAR).Buons and LEDsThe buons are used to trig alarms. For ROOM and ROOM+PEAR it will also change the unit’s mode.The dierent modes are:• Standby mode• Alarm mode• Presence mode• Assistance modeThe LEDs indicate acon and/or the unit’s state and can either blink or light steady depending on how the units is congured and/or used.Ports 1 and 2The tele jack connector provides two ports when a stereo tele plug is used or one port if a mono teleplug is used .The ports are of type Normally Open.
7WALL Family User manual NE41 12005- 02 v2.0Both ports have a common ground and must be connected to potenal free contacts (see below).Port 1Port 1Port 2If an inserted tele plug is removed, the unit sends a Tamper alarm. If the plug is inserted again the unit sends a Tamper OK alarm.Manual conguraon(not valid for ROOM and ROOM+PEAR)Any unit can be manually congured regarding adding transmiers and how the two relay outputs should act when the added transier is acvated.The procedure is in short:• Determine what posion to acvate• Add the radio transmier• Determine the acon when the added transmier is acvatedPlease read the following instrucon carefully before aempng to manually congure a radio transmier.1. Power o the unit (both 24VDC and baeries must be removed)2. Remove J23. Power on the unit and replace the J2 within 5 seconds from power on.4. The LED blinks green 3 mes.
8 WALL Family User manual NE41 12005- 02 v2.05. Aer the inial “three green blink”, the unit now starts to blink red. The number of blinks indicates the current radio posi-on, i.e. 3 red blinks equals radio posion 3.12345678126. To select radio posion, press any buon, port or input.7. The unit will conrm the selecon by lighng green for 2 second.8. Now acvate the radio transmit-ter (e.g. press the red buon on an ATOM).9. The unit will conrm the succes-ful recepon of the radio ID code by lighng green for 2 seconds.10. The unit now starts blinking green, allowing the seng the acon for relay 1.12345612The number of blinks indicates what acon to set.1 blink Pulse2 blinks On3 blinks O4 blinks Toggle5 blinks No acon6 blinks Stop pulse11. Press any port, buon or input at the appropriate acon blink.12. The unit now starts blinking red, allowing the seng the acon for relay 2 (see #10).1234561213. Acvate any port, buon or input at the appropriate acon blink.14. If successful, the LED rapidly blinks green for 2 seconds.At any stage during the manual conguraon, if there is an unsuccessful conguraon, the LED will blink rapidly for 2 seconds. When this happens the manual conguraon is cancelled and it is necessary to restart the procedure.
9WALL Family User manual NE41 12005- 02 v2.0In the event of inacvity during man-ual conguraon (e.g. a transmier is not acvated aer #8 or a port/buon is not pressed aer #11) the unit waits for 60 seconds and then returns to normal mode. The manual conguraton must then be restarted.Remove a transmierTo remove a transmier, follow steps #1 trough #7 above. Aer step #7, remove jumper J2. The device will conrm the deleon by rapidly blink green for 2 seconds.WALL family ProgrammerAll WALL units can be congured with a Neat Programming Unit (NPU) and the soware WALL Family Programmer.The NPU can be purchased from NEAT Electronics and the soware can be downloaded from our home-page: www.neat-group.com/se/enMore informaonFor more informaon, please refer to WALL Family - Technical Handbook, NE41 11014-02.Important!Care and maintenance• Do not expose to direct sunlight.• Keepawayfromdust,moistanddirt.• Donotdrop,knock,twistorshakethedevice.• Donotwarmupthedeviceoruseitnearre. • Cleanthedevicewithasocloth,damp-enedslightlywithmildsoapywater.Donotcleanthedevicewithharshchemicals,solventsorothercorrosivesubstances.Safety Notes• Readinstruconspriortouse.• Alwaystestthesystemperinstruconsprior to use.• Thisproductmaynotbesuitableforallpersons.
10 WALL Family User manual NE41 12005- 02 v2.0• OurunitsareNOTintendedforanylifesupportdevice,thusintendingadevicewhosemalfunconmayresultin damagetoalife.DisposalAttheendoftheproduct’suselife,pleasedisposeofitatappropriatecolleconpointsprovided in your country. For disposal or recyclinginformaon,pleasecontactyourlocalauthoriesortheElectronicIndustriesAlliance(EIA,www.eiae.org).IntheEuropeanUnion,thebinlabelindicatesthatthisproductshouldnotbedisposedofwithhouseholdwaste.Itshouldbedepositedatanappropriatefacilitytoenablerecoveryand recycling or returned to NEAT Electronics AB.• Thisproductshouldnotbeasubstutefortherounevisualmonitoring protocolbycaregiver.• Mustnotbeusedinsituaonswhereadelayinthearrivalofappropriatemedicalcare,couldleadtoapotenallylife-threateningsituaon.• Checkdeviceregularlyandreplacewhennecessary.• Do not integrate to other systems other thanthosespeciedinthisdocument.• Alwayskeepthedevicedry.Exposuretoexcessivemoistcancausemalfuncon.• TheproductfullstherequirementsoftheEMC-Direcve2004/108/EC.• Itdoesnotcauseelectromagnecdistur-bancesundernormalworkingcondions.• Theproductcanbeplacednearotherproducts or devices as long as mechanical vibraonisnotpresent.• Alwayscheckthefunconofthe productaermakingadjustments.• Pleaseremovebaeriesiftheunitistobeoutofuseorstoredforanextendedperiodofme.
11WALL Family User manual NE41 12005-02 v2.0Technical dataData ValueDimension (incl. wallframe)(mm) 86 x 86 x 26 mmWeight (incl. baeries) 125 gFrequencytransmit EU US868.7, 869.2 MHz 916.2, 916.4 MHzFrequencyreceive EU US868.7, 869.2, 869.4 MHz 916.2, 916.4 MHzSupply voltagemin 10 VDCSupply powermax 28 VDC, 100 VABaery type GP Ultra Alkaline AAA or GP Super Alkaline AAARelay output, switchingmax 30 VDC, 250 mABaery life 5 years3Buon push memin 150 msWired input open/closemin 150 msJumper change delay 3 sTamper remove/insert delay 3 s3Radio test alarm + 4 alarms every day (when baery powered)The frequencies for each market is programmed during producon and not changeable by the user.
www.neatelectronics.se

Navigation menu