NEC Platforms 241 Small size 2.4GHz wireless transceiver module User Manual TY24FM E2024 DataSheet080306

NEC Engineering, Ltd. Small size 2.4GHz wireless transceiver module TY24FM E2024 DataSheet080306

User Manual

Document Number DS170-L0704-02 January 2008 （rev.1.0） Small size 2.4GHz wireless transceiver module 「TY24FM-E2024-01」 The TY24FM-E2024-01 is a 2.4GHz Low power wireless transceiver module. The module contains all required hardware and software to evaluate and develop wireless communication based on IEEE 802.15.4 PHY. Product Photo ＜ Feature＞ ・ Integrated by MCU, RF circuits, antenna ・ Communicated by the functions of device detect and data transmission ・ Based on IEEE802.15.4.PHY ・ 1:N communication style ・ Controlled by UART I/F ・ Low power sleep mode ・ DC3.0V supply voltage ・ Certified CE, and FCC, Japan Radio Law E2022 E2024
Document Number DS170-L0704-02 January 2008 （rev.1.0） ＜Specification＞ Product name TY24FM-E2024-01 Carrier frequency 2400ＭＨｚ～2483.5ＭＨｚ （16 channel） Communication protocol Original protocol Modulation DS-SS (Direct Sequence Spectrum Spread) Wireless bit rate Maximum 250Kbps （Subject to the communication environment） Transmit Power Maximum 1mW (At the feeding point of the antenna) Transmit Distance About 40m （Reference value） Interface ・Serial communication Baud rate : Maximum 38.4kbps Data length: 8bit Parity: no parity Stop: 1stop bit Flow control: no flow control Supply Voltage ・DC 3.0V (Recommended) Current Consumption ・TX: Typ. 41mA ・RX: Typ. 43mA ・Sleep Mode : Typ. 3uA (power-supply voltage DC 3.0Ｖ) Operating conditions ・Operating temperature range：-15℃～+70℃ ・Operating humidity range：85%RH or less （No do be dewy） Weight About 2g Dimensions 27.8mm×16.2mm×3.9mm （D×W×H） Restrictions RoHS-Compliant (Pb free) Radio Law Japan Radio Law, CE, and FCC certification
Document Number DS170-L0704-02 January 2008 （rev.1.0） ＜FCC statement＞ This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by NEC Engineering, Ltd. could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure Information: The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.
Document Number DS170-L0704-02 January 2008 （rev.1.0） ＜output I/F connector＞ connector type ： Stacking connector 20pin 0.5mm pitch product name ： JST 20R-JMCS-G-TF(NSA) Receptacle Signal level ：CMOS Customer ： Recommended connector JST 20P3.0-JMCS-G-TF(N) Plug Stacking height 3mm ・Module pin definitions Pin No. Pin name Type Definition State of reset Detail 1 VCC power Power － DC3.0Ｖ(Recommend power supply voltage) 2 GND GND GND － 3 TxD OUT UART data transmit HiZ 4 RxD IN UART data receive HiZ Internal Pullup 5 WAKEUP IN WAKEUP input － Sleep mode enable = High /disable = Low input 6 RESET IN RESET input － RESET Low input 7 Reserve － Reserve － n.c 8 Reserve － Reserve － n.c 9 Reserve － Reserve － n.c 10 Reserve － Reserve － n.c 11 VCC power power － DC3.0Ｖ(Recommend power supply voltage) 12 GND GND GND － 13 GND GND GND － 14 Reserve － Reserve － n.c 15 Reserve － Reserve － n.c 16 Reserve － Reserve － n.c 17 Reserve － Reserve － n.c 18 Reserve － Reserve － n.c 19 MODE OUT Mode output － Normal mode = Low / sleep mode =High output 20 GND GND GND －
Document Number DS170-L0704-02 January 2008 （rev.1.0） ＜Dimensions＞ unit：mm
Document Number DS170-L0704-02 January 2008 （rev.1.0） ＜Installation＞ ＮＥＣ Ｅｎｇｉｎｅｅｒｉｎｇ，Ｌｔｄ. General inquiries Sales&Marketing Division 4-10-27 Higashishinagawa Shinagawa-ku Tokyo 140-0002 Japan TEL: +81 3 6713 1230 URL http://www.nec-eng.com/ Contact

Navigation menu