NEC 915MSG 915MHz Wireless Transceiver Module User Manual 915M SG DataSheet
NEC Corporation 915MHz Wireless Transceiver Module 915M SG DataSheet
NEC >
User Manual
Small size 915MHz 915MHz wireless transceiver module 「915M_ 915M_SG」 SG」 The 915M-SG is a 915MHz Low power wireless transceiver module. Product Photo < Features Features> ・ Integrated by MCU, RF circuits, antenna ・ Communicated by the functions of device detect and data transmission ・ 1:1,1:N, and N:N communication style ・ Controlled by UART I/F ・ Low power sleep mode ・ DC3.0V supply voltage ・ FCC certification Document Number IT471-0013-X701 February 2011 (rev.1.0) <Specifications Specifications> Product name Carrier frequency Communication protocol Modulation Wireless bit rate Transmit Power Effective range Interface 915M_SG 903.5MHz~926.5MHz (24 channel) Proprietary protocol GFSK 9.6kbps/100kbps Maximum 8dBm (At the feeding point of the antenna) About 250m (Reference value) ・UART serial communication Data length: 8bit Baud rate : 9.6kbs,19.2kbps,38.4kbps,57.6kbps,115.2kbps Data length: 8bit Parity: no parity Stop: 1stop bit Flow control: none Supply Voltage Current Consumption Operating conditions Weight Dimensions Restrictions Reguration ・DC +3.0±0.3V ・TX: Typ. 34mA ・RX: Typ. 23mA ・Sleep Mode : Typ. 3uA (power-supply voltage DC 3.0V) ・Operating temperature range:-20℃~+75℃ ・Operating humidity range:85%RH or less (No do be dewy) About 3g 37.3mm×18.8mm×5.2mm (D×W×H) RoHS-Compliant (Pb free) FCC certification Document Number IT471-0013-X701 February 2011 (rev.1.0) <FCC statement> statement> This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by NEC Engineering, Ltd. could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure Information: The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. Document Number IT471-0013-X701 February 2011 (rev.1.0) <output I/F connector> connector> connector type product name Signal level : Stacking connector 20pin 0.5mm pitch : JST 20R-JMCS-G-TF(NSA) Receptacle : CMOS Customer : Recommended connector JST 20P3.0-JMCS-G-TF(N) Plug Stacking height 3mm ・Module pin definitions Pin No. Type VCC power Power - GND GND GND - TxD OUT UART data transmit HiZ RxD IN UART data receive HiZ WAKEUP IN WAKEUP input HiZ RESET IN RESET input HiZ GPIO1 - Reserve - n.c TSI IN TSI input HiZ internal Pullup TSO OUT TSO output HiZ 10 GPIO4 Reserve - n.c 11 VCC power power - DC3.0V(Recommend power supply voltage) 12 GND GND GND - 13 GND GND GND - 14 CTS - 15 P_STATE 16 FLMD0 - TEST Pin - n.c 17 TOOL0 - TEST Pin - n.c 18 TOOL1 - TEST Pin - n.c 19 RTS - Reserve 20 GND GND - OUT Definition State of reset Pin name Detail DC3.0V(Recommended power supply voltage) Sleep mode enable = High /disable = Low input Internal Pullup RESET Low input Internal Pullup Reserve n.c Mode output Normal mode = Low / sleep mode =High output GND Document Number IT471-0013-X701 February 2011 (rev.1.0) n.c - <RF connector> connector> RF Connector connects with antenna through cable. connector type product name impedance : Ultra small surface mount coaxial connector : Hirose Electronic U.FL-R-SMT-1 : 50Ω <antenna and cable for antenna connection> connection> ・antenna product name impedance antenna gain : MIDORI ANZEN NMA-01 : 50Ω : less than 3dBi Unit:mm ・cable for antenna connection product name : Hirose Electronic impedance : 50Ω cable length : 300mm HRMBPJ-U.FL-04N1-A-100RS Unit:mm Document Number IT471-0013-X701 February 2011 (rev.1.0) <Dimensions> Dimensions> RF connector cap 20pin Staking connector Staking hight 3mm Top view Side view unit:mm Document Number IT471-0013-X701 February 2011 (rev.1.0) <Installation> Installation> Contact NEC Engineering,Ltd. General inquiries Sales&Marketing Division 4-10-27 Higashishinagawa Shinagawa-ku Tokyo 140-0002 Japan TEL: +81 3 6713 1200 URL http://www.nec-eng.com/ Document Number IT471-0013-X701 February 2011 (rev.1.0)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 7 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : cd18cd1d-4aeb-11e0-0000-850377de93b3 Producer : GPL Ghostscript 9.0 Keywords : () Modify Date : 2011:03:07 16:55:32+09:00 Create Date : 2011:03:07 16:55:32+09:00 Creator Tool : PDFCreator Version 1.1.0 Document ID : cd18cd1d-4aeb-11e0-0000-850377de93b3 Format : application/pdf Title : 915M-SG_DataSheet Creator : 1139701011438 Description : () Author : 1139701011438 Subject :EXIF Metadata provided by EXIF.tools