NEO ELECTRONICS NAS-WS02W Smart Device User Manual

SHENZHEN NEO ELECTRONICS CO.,LTD Smart Device

User Manual

Productconfiguration
Mainfunction
Detectionofwaterleakage
Specification
Reset
1.Pressandholdtheresetbuttonfor6s,theindicator
willblinkrapidly.Thedeviceisinsmartwimodeto.
2.Presstheresetbuttonagain,theindicatorwillblink
slowly.ThedeviceisinAPmode.
Parameter
Battery:CR23Vx1
Standbycurrent13uA
Standbytime5years
Usetime1year15times/day);2years7times/day
WirelessType:2.4GHz,1T1R
Protocol:IEEE802.11b/g/n
WirelessRange45m
OperatingTemperature:0℃~40(32°F104°F)
OperatingHumidity:20%85%
StorageTemperature:060(32°F140°F)
StorageHumidity:0%90%
WaterproofgradeIP67
Size:67mmx67mmx24mm
AddDevice
1.RunTuyaSmartfromyousmartphonedesktop.
2.Registerandlogin
3. Choosethedevicethatyouwanttoadd.AddingdevicebysmartwiorAPmode.
configureinternet
SmartWiFi
1. Pressandholdtheresetbuttonfor6s,theindicatorwillblinkrapidly.ThedeviceisinsmartWiFi
mode.
2. ClickConfirmindicatorrapidlyblink
3. ConfiguringnetworkbasedonpromptoftheAPP.
AP Mode
1. Presstheresetbuttonfor6sagain,theLEDwillblinkslowly.ThedeviceisinAPmode.
2. ClicktheAPMode
3.ConfiguringnetworkbasedonpromptoftheAPP.
3.device
4. Reset
Scenes
Bysettingscenelettwodevicesarelinkage.
Sharing
By sharing devicelet other people can control the device without adding.
Pushinformation
Themultiplealarminthreeminuteswillonlybepushedonce
LEDstate
devicestatusLEDstate
SmartWiFiRedLEDwillrapidlyblink
APmodeRedLEDwillslowlyblink
AlarmLEDwillrapidlyblinkfor3timesalarmwillring3
times.thenrapidblinkingcyclicallyafterslowly
blinkfor1timeAlarmringsaccordingly
resetLEDwillbeonfor4sthenOFFanditwillready
forconfigurationafter3s
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
* RF warning for Mobile device:
The antenna(s) used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter Device.

Navigation menu