NEO ELECTRONICS NAS-WS02W Smart Device User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3837637
Application ID	P8/O+XHdC0o5I9kl1hSxkA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.05kB (238139 bits)
Date Submitted	2018-05-03 00:00:00
Date Available	2018-05-03 00:00:00
Creation Date	2018-04-26 17:10:08
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2018-04-26 17:10:08
Document Title	Microsoft Word - wifi溢水器说明书.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

Product configuration
Main function
Detection of water leakage
Specification
Reset：
1.Press and hold the reset button for 6s, the indicator
will blink rapidly. The device is in smart wi mode to.
2.Press the reset button again, the indicator will blink
slowly. The device is in AP mode.
Parameter
Battery: CR2‐3V x 1
Standby current：13uA
Standby time：5 years
Use time：1 year（15 times/day）；2 years（7 times/day）
Wireless Type:2.4GHz, 1T1R
Protocol:IEEE 802.11b/g/n
Wireless Range：45m
Operating Temperature:0℃～ 40℃ (32°F～104°F)
Operating Humidity: 20% ～ 85%
Storage Temperature:0℃ ～ 60℃ (32°F ～140°F)
Storage Humidity:0% ～ 90%
Waterproof grade：IP67
Size:67mm x 67mm x 24mm
Add Device
1.Run “TuyaSmart”from you smartphone desktop.
2.Register and login
3. Choose the device that you want to add. Adding device by smart wi or AP mode.
configure internet：
Smart Wi‐Fi
1. Press and hold the reset button for 6s, the indicator will blink rapidly. The device is in smart Wi‐Fi
mode .
2. Click “Confirm indicator rapidly blink”
3. Configuring network based on prompt of the APP.
AP Mode
1. Press the reset button for 6s again, the LED will blink slowly. The device is in AP mode.
2. Click the “AP Mode”
3.Configuring network based on prompt of the APP.
3.device
4. Reset
Scenes
By setting scene ，let two devices are linkage.
Sharing
By sharing device，let other people can control the device without adding.
Push information
The multiple alarm in three minutes will only be pushed once
LED state
device status
LED state
Smart Wi‐Fi
Red LED will rapidly blink
AP mode
Red LED will slowly blink
Alarm
LED will rapidly blink for 3 times（alarm will ring 3
times）. then rapid blinking cyclically after slowly
blink for 1 time（Alarm rings accordingly）
reset
LED will be on for 4s then OFF，and it will ready
for configuration after 3s
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
* RF warning for Mobile device:
The antenna(s) used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter Device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2018:04:26 17:10:08+08:00
Modify Date                     : 2018:04:26 17:10:08+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Title                           : Microsoft Word - wifi溢水器说明书.doc
Creator                         : Administrator
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:a8f090db-495c-4ac5-b8a0-867844cd923a
Instance ID                     : uuid:d9fa3310-3d66-45b0-9b46-b1888f7bdeb6
Page Count                      : 7

EXIF Metadata provided by EXIF.tools