NEOSEN ENERGY 3211352HP HP Tri-Mode Wireless Charging Pad User Manual

NEOSEN ENERGY HP Tri-Mode Wireless Charging Pad

User Manual

APPLICATIONREVISIONSAPPROVALSNEXT ASSYPROJECT NO.ECN NO.REVDESCRIPTIONDATEAPPROVED---1.13SPECIFICATION RELEASE5/6/20151.14UPDATE SPECIFICATION6/30/20151.15UPDATE SPECIFICATION7/20/20151.16UPDATE SPECIFICATION8/19/20151.17UPDATE SPECIFICATION9/4/2015APPROVALSDATEHP RESTRICTEDTHIS DOCUMENT AND ANYASSOCIATED DATA CONTAINRESTRICTED INFORMATION THATIS HEWLETT-PACKARD (HP)PROPERTY. DO NOT DISCLOSE TOOR DUPLICATE FOR OTHERSEXCEPT AS AUTHORIZED BY HP.DRAWNCHECKEDDSGN ENGRNAM NGUYEN2/12/15ENG2015 COMMERCIAL WIRELESS CHARGER “BOLT”MFGPROCUREMENTUNLESS OTHERWISE SPECIFIED,DIMENSIONS ARE IN INCHES[MILLIMETERS]. TOLERANCES ARE:QALEGALSIZEADRAWING NO.REVAGENCY1.17FRACTIONSDECIMALSANGLES1/32.XX .02[0.5]1DO NOT SCALE DRAWINGSUPPLEMENTS:EF,PDFSHEET 1OF15.XXX .010 [0.25]
TABLE OF CONTENTS1. SCOPE....................................................................................................................................................................................62. ORDER OF PRECEDENCE................................................................................................................................................63. DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS)................... 64. GENERAL EXPECTATIONS.............................................................................................................................................85. HP PART NUMBER.............................................................................................................................................................86. WIRELESS CHARGE DESIGN REQUIREMENTS....................................................................................................... 96.1 WIRELESS DESIGN........................................................................................................................................................................97. QUALITY ASSURANCE PROVISIONS......................................................................................................................................128. CHANGE NOTICE.............................................................................................................................................................139. PACKAGING/SHIPPING..................................................................................................................................................13APPENDIX A 13
REVISION HISTORYRevisionDateAuthorDescription1.102/13/15Nam NguyenOfficial release1.114/9/15Nam NguyenDimension change 167.2mm x 90.2mm1.124/16/15Nam NguyenAdd support for AiO Stand base.Add different support for DC plug for Standalone and AiOstand base.
1.135/5/2015Nam NguyenAdd new part number for power adaptor with 1.5M cableUpdate GP fileUpdate material, color for top and bottom cover.1.146/22/2015Nam NguyenDelete SwitchDelete AudibleChange LED from Bi-Color to Single ColorUpdate LED behavior tableUpdate GP file (BOLT_GB_DB_15-0618)Update color and material1.157/20/2015Nam NguyenAdd update FW function via Micro USBLED brightness luminance = 100 nitsAmbient operation temp: 35 deg C and 10 degree C deltatemperature for module (45 degree C Max)ESD 8KV contact and 15 KV Air1.168/19/2015Nam NguyenUpdate LED table behaviorUpdate Pulsing and Flashing duty cycle.Update Tick mark on the Bolt design1.179/4/2015Nam NguyenUpdate ID GP fileUpdate Top and Bottom cover material and color
1. SCOPEThis specification defines the requirements for a tri-mode (Qi, PMA, A4WP class 2) wireless charging module forcharging a single phone or phablet of up to 6 inch diagonal screen length. The OEM need to provide the completewireless charging solution and required certifications. This module will be standalone module or integrated to AiOstand base. The standalone module will have cover around the electronic, coil, and shielding. For AiO stand base,only the electronic, coil, and shield.2. ORDER OF PRECEDENCEIn the event of a conflict between this specification and references cited herein, the order of precedence shall be thisspecification, then any reference documents, and finally any appendices.3. DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS)This section defines requirements that are applicable to all products and product components. Individualcomponents specifications may amend or append requirements to this base set as part of their component-specificrequirements, but otherwise these requirements are applicable in all cases.Specifications referenced within this section form a part of this specification to the extent specified herein. Unlessotherwise indicated, the document is of the issue in effect on the date of invitation to bid or request for proposal.
3.1.1 Environmental Design Requirements3.1.1.1 The following embedded document contains environmental requirements that the product mustincorporate into its design to meet both regulated and HP-voluntary initiatives. Any deviationfrom these requirements will cause this product to not be in compliance with the standards that HPenforces to maintain its responsibility to the environment.Environmental System Specification for 2016 CMIT Acessories - 012914.docx3.1.2 Accessibility3.1.2.1 SECTION 508 ACCESSIBILITY - US• The system must comply with the section 508 Accessibility - US requirements. Please reference:http://www.section508.gov/index.cfm?FuseAction=content&ID=123.1.2.2 CVAA• The system (modules) must comply with the Twenty-First Century Communications and VideoAccessibility Act (CVAA) via completion of the HP CVAA worksheet available from theAccessibility & Aging Program Office at ability@hp.com for each module that includesaccessibility considerations. (ie. keyboards, VOIP software, electronic messaging, videoconferencing (ACS))
4. GENERAL EXPECTATIONSa) All documents shall be provided in electronic form in industry standard formats such as Adobe Acrobat PDF,Microsoft Excel, etc. unless otherwise indicated. Adobe Acrobat documents should be searchable and generatedfrom an electronic document–not from a document which was scanned.b) Any performance related discussions shall be between HP/wireless charge suppliers only.c) Measurement/simulation data shall be provided to HP only.d) Mechanical related information (e.g. 3D drawing, cable/connector definition/type, etc) shall be provided byODM.e) ODM supplier’s SOP documentations shall be available upon request.f) Schedule/sample quantity shall be provided by ODM.g) Additional expectations are described in the HPPA documents.5. HP PART NUMBERHP’s 6-3 part number for webcam = TBD.
6. WIRELESS CHARGE DESIGN REQUIREMENTSHP reserves the right to modify the design requirements with advance notice.6.1 WIRELESS DESIGNTechnology: Tri Mode (Qi, PMA, and A4WP Class 2)Power: Qi & PMA 5W delivered to receiving device;A4WP Class 2 10W delivered to receiving device.X-Y Dimension: 167.2mm x 90.2mm (of charging surface and electronic)Thickness: As thin as possible.Cable routing for standalone: Cable recess plug under the body of the moduleCable routing for AiO stand: Cable will plug to the DC plug at the side of the AiO stand base.Firmware update: To maintain the up to date interoperability of the wireless deviceUnit need to be able to update FW via Micro USB port.LED Status: Need to provide LED to show status. Bi-Color (White and Amber)Input Power: 12VHeader for LED: 2 or 3 pin header for single color (White)DC Plug DC Plug down for (Standalone Module)DC plug with extension cable to the edge of the AiO base.Operation temperature: 35 degree C ambient and 10 degree C delta temperature for themodule means 45 degree C max.ESD: 8 kV contact and 15 kV Air.
Certification: ODM need to obtain all applicable regulatory certifications forA4WP and PAM standards body certificationsLocation of Certification Logo: TBDIcon/Logo: Top icon location for centering the device (Final icon TBD)6.1.1 Power AdaptorSee spec 794797-A-WAE009-022G2 => 1.5 mm DC cable6.1.2 LED Behavior (preliminary)LED luminance: 100 nits.Flashing: 50% duty cyclePulsing: 10% duty cycle at 1HzLED StatusLEDUnplugged/OffOffOn/Ready (=Charge complete)Solid WhiteChargingSolid AmberError conditionFlash AmberFW Update in processPulsing White6.1.3 MechanicalTop Cover:oMaterial = Plastic – PC/ABS + 15% talcoPlastic Color = Jack BlackoFinish = MT11000oSurface = PaintoPaint Base Coat = Sparkling Black UVoPaint Top Coat = Soft touch clear UVBottom
oRubber feetProcess = Die cast aluminumMaterial = AluminumFinish = SmoothSurface = PaintPaint Primer = TBDPaint Base Coat = HP Blue (PM285c) PUPaint Top Coat = PU Soft touch Clear6.1.4 GP (Graphic Plan) FileBOLT_GP_SI_15-0827
7. QUALITY ASSURANCE PROVISIONS
Unless otherwise specified in the contract or purchase order, the supplier shall be responsible for the quality of thepart as it is delivered to HP. The supplier shall be responsible for having controlled processes to ensure product is intotal compliance with this specification. Failing lots shall be subject to return or other supplier-corrective action.In addition to visual inspections, the following minimal tests shall be performed on every finished goods (100%)before shipping to HP/ODM sites/factories.8. CHANGE NOTICEDuring development or after tooling release, any design or process changes initiated by ODM supplier shall becommunicated to HP through email and approved by HP prior to implementation. The supplier must provideadequate samples and reports to allow HP to verify the change.9. PACKAGING/SHIPPINGPackaging shall sufficient to protect against damage or loss during shipment from the supplier to destinationspecified in the purchase order. Packaging, identification, and palletization shall be in accordance with HPDocument 109893 (Appendix A).It shall be clearly marked with Supplier part number, HP part number, and a Revision number.APPENDIX AHP SUPPLIER PACKAGING/MATERIAL HANDLING SPECIFICATION
109893_AC_001.pdfNOTE: The USB port is just only for engineering purposes in the factory and cannot not be used by the end-user.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipmentshould be installed and operated with minimum distance of 20 cm between the radiator and your body.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to thisequipment. Such modifications could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferenceby one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu