NEOSEN ENERGY 3211352HP HP Tri-Mode Wireless Charging Pad User Manual
NEOSEN ENERGY HP Tri-Mode Wireless Charging Pad
User Manual
APPLICATION
REVISIONS
APPROVALS
NEXT ASSY
PROJECT NO.
ECN NO.
REV
DESCRIPTION
DATE
APPROVED
---
1.13
SPECIFICATION RELEASE
5/6/2015
1.14
UPDATE SPECIFICATION
6/30/2015
1.15
UPDATE SPECIFICATION
7/20/2015
1.16
UPDATE SPECIFICATION
8/19/2015
1.17
UPDATE SPECIFICATION
9/4/2015
APPROVALS
DATE
HP RESTRICTED
THIS DOCUMENT AND ANY
ASSOCIATED DATA CONTAIN
RESTRICTED INFORMATION THAT
IS HEWLETT-PACKARD (HP)
PROPERTY. DO NOT DISCLOSE TO
OR DUPLICATE FOR OTHERS
EXCEPT AS AUTHORIZED BY HP.
DRAWN
CHECKED
DSGN ENGR
NAM NGUYEN
2/12/15
ENG
2015 COMMERCIAL WIRELESS CHARGER “BOLT”
MFG
PROCUREME
NT
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES
[MILLIMETERS]. TOLERANCES ARE:
QA
LEGAL
SIZE
A
DRAWING NO.
REV
AGENCY
1.17
FRACTIONS
DECIMALS
ANGLES
1/32
.XX .02
[0.5]
1
DO NOT SCALE DRAWING
SUPPLEMENTS:
EF,PDF
SHEET 1
OF
15
.XXX .010 [0.25]
TABLE OF CONTENTS
1. SCOPE....................................................................................................................................................................................6
2. ORDER OF PRECEDENCE................................................................................................................................................6
3. DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS)................... 6
4. GENERAL EXPECTATIONS.............................................................................................................................................8
5. HP PART NUMBER.............................................................................................................................................................8
6. WIRELESS CHARGE DESIGN REQUIREMENTS....................................................................................................... 9
6.1 WIRELESS DESIGN........................................................................................................................................................................9
7. QUALITY ASSURANCE PROVISIONS......................................................................................................................................12
8. CHANGE NOTICE.............................................................................................................................................................13
9. PACKAGING/SHIPPING..................................................................................................................................................13
APPENDIX A 13
REVISION HISTORY
Revision
Date
Author
Description
1.10
2/13/15
Nam Nguyen
Official release
1.11
4/9/15
Nam Nguyen
Dimension change 167.2mm x 90.2mm
1.12
4/16/15
Nam Nguyen
Add support for AiO Stand base.
Add different support for DC plug for Standalone and AiO
stand base.
1.13
5/5/2015
Nam Nguyen
Add new part number for power adaptor with 1.5M cable
Update GP file
Update material, color for top and bottom cover.
1.14
6/22/2015
Nam Nguyen
Delete Switch
Delete Audible
Change LED from Bi-Color to Single Color
Update LED behavior table
Update GP file (BOLT_GB_DB_15-0618)
Update color and material
1.15
7/20/2015
Nam Nguyen
Add update FW function via Micro USB
LED brightness luminance = 100 nits
Ambient operation temp: 35 deg C and 10 degree C delta
temperature for module (45 degree C Max)
ESD 8KV contact and 15 KV Air
1.16
8/19/2015
Nam Nguyen
Update LED table behavior
Update Pulsing and Flashing duty cycle.
Update Tick mark on the Bolt design
1.17
9/4/2015
Nam Nguyen
Update ID GP file
Update Top and Bottom cover material and color
1. SCOPE
This specification defines the requirements for a tri-mode (Qi, PMA, A4WP class 2) wireless charging module for
charging a single phone or phablet of up to 6 inch diagonal screen length. The OEM need to provide the complete
wireless charging solution and required certifications. This module will be standalone module or integrated to AiO
stand base. The standalone module will have cover around the electronic, coil, and shielding. For AiO stand base,
only the electronic, coil, and shield.
2. ORDER OF PRECEDENCE
In the event of a conflict between this specification and references cited herein, the order of precedence shall be this
specification, then any reference documents, and finally any appendices.
3. DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS)
This section defines requirements that are applicable to all products and product components. Individual
components specifications may amend or append requirements to this base set as part of their component-specific
requirements, but otherwise these requirements are applicable in all cases.
Specifications referenced within this section form a part of this specification to the extent specified herein. Unless
otherwise indicated, the document is of the issue in effect on the date of invitation to bid or request for proposal.
3.1.1 Environmental Design Requirements
3.1.1.1 The following embedded document contains environmental requirements that the product must
incorporate into its design to meet both regulated and HP-voluntary initiatives. Any deviation
from these requirements will cause this product to not be in compliance with the standards that HP
enforces to maintain its responsibility to the environment.
Environmental
System Specification for 2016 CMIT Acessories - 012914.docx
3.1.2 Accessibility
3.1.2.1 SECTION 508 ACCESSIBILITY - US
• The system must comply with the section 508 Accessibility - US requirements. Please reference:
http://www.section508.gov/index.cfm?FuseAction=content&ID=12
3.1.2.2 CVAA
• The system (modules) must comply with the Twenty-First Century Communications and Video
Accessibility Act (CVAA) via completion of the HP CVAA worksheet available from the
Accessibility & Aging Program Office at ability@hp.com for each module that includes
accessibility considerations. (ie. keyboards, VOIP software, electronic messaging, video
conferencing (ACS))
4. GENERAL EXPECTATIONS
a) All documents shall be provided in electronic form in industry standard formats such as Adobe Acrobat PDF,
Microsoft Excel, etc. unless otherwise indicated. Adobe Acrobat documents should be searchable and generated
from an electronic document–not from a document which was scanned.
b) Any performance related discussions shall be between HP/wireless charge suppliers only.
c) Measurement/simulation data shall be provided to HP only.
d) Mechanical related information (e.g. 3D drawing, cable/connector definition/type, etc) shall be provided by
ODM.
e) ODM supplier’s SOP documentations shall be available upon request.
f) Schedule/sample quantity shall be provided by ODM.
g) Additional expectations are described in the HPPA documents.
5. HP PART NUMBER
HP’s 6-3 part number for webcam = TBD.
6. WIRELESS CHARGE DESIGN REQUIREMENTS
HP reserves the right to modify the design requirements with advance notice.
6.1 WIRELESS DESIGN
Technology: Tri Mode (Qi, PMA, and A4WP Class 2)
Power: Qi & PMA 5W delivered to receiving device;
A4WP Class 2 10W delivered to receiving device.
X-Y Dimension: 167.2mm x 90.2mm (of charging surface and electronic)
Thickness: As thin as possible.
Cable routing for standalone: Cable recess plug under the body of the module
Cable routing for AiO stand: Cable will plug to the DC plug at the side of the AiO stand base.
Firmware update: To maintain the up to date interoperability of the wireless device
Unit need to be able to update FW via Micro USB port.
LED Status: Need to provide LED to show status. Bi-Color (White and Amber)
Input Power: 12V
Header for LED: 2 or 3 pin header for single color (White)
DC Plug DC Plug down for (Standalone Module)
DC plug with extension cable to the edge of the AiO base.
Operation temperature: 35 degree C ambient and 10 degree C delta temperature for the
module means 45 degree C max.
ESD: 8 kV contact and 15 kV Air.
Certification: ODM need to obtain all applicable regulatory certifications for
A4WP and PAM standards body certifications
Location of Certification Logo: TBD
Icon/Logo: Top icon location for centering the device (Final icon TBD)
6.1.1 Power Adaptor
See spec 794797-A
-WAE009-022G2 => 1.5 mm DC cable
6.1.2 LED Behavior (preliminary)
LED luminance: 100 nits.
Flashing: 50% duty cycle
Pulsing: 10% duty cycle at 1Hz
LED Status
LED
Unplugged/Off
Off
On/Ready (=Charge complete)
Solid White
Charging
Solid Amber
Error condition
Flash Amber
FW Update in process
Pulsing White
6.1.3 Mechanical
Top Cover:
oMaterial = Plastic – PC/ABS + 15% talc
oPlastic Color = Jack Black
oFinish = MT11000
oSurface = Paint
oPaint Base Coat = Sparkling Black UV
oPaint Top Coat = Soft touch clear UV
Bottom
oRubber feet
Process = Die cast aluminum
Material = Aluminum
Finish = Smooth
Surface = Paint
Paint Primer = TBD
Paint Base Coat = HP Blue (PM285c) PU
Paint Top Coat = PU Soft touch Clear
6.1.4 GP (Graphic Plan) File
BOLT_GP_SI_15-0827
7. QUALITY ASSURANCE PROVISIONS
Unless otherwise specified in the contract or purchase order, the supplier shall be responsible for the quality of the
part as it is delivered to HP. The supplier shall be responsible for having controlled processes to ensure product is in
total compliance with this specification. Failing lots shall be subject to return or other supplier-corrective action.
In addition to visual inspections, the following minimal tests shall be performed on every finished goods (100%)
before shipping to HP/ODM sites/factories.
8. CHANGE NOTICE
During development or after tooling release, any design or process changes initiated by ODM supplier shall be
communicated to HP through email and approved by HP prior to implementation. The supplier must provide
adequate samples and reports to allow HP to verify the change.
9. PACKAGING/SHIPPING
Packaging shall sufficient to protect against damage or loss during shipment from the supplier to destination
specified in the purchase order. Packaging, identification, and palletization shall be in accordance with HP
Document 109893 (Appendix A).
It shall be clearly marked with Supplier part number, HP part number, and a Revision number.
APPENDIX A
HP SUPPLIER PACKAGING/MATERIAL HANDLING SPECIFICATION
109893_AC_001.pdf
NOTE: The USB port is just only for engineering purposes in the factory and cannot not be used by the end-user.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.