NEOSEN ENERGY NEO-0002 ChargeSpot User Manual 15 NEO 0002 UserMan

Download:
Mirror Download [FCC.gov]
Document ID	3224220
Application ID	2juPUBCgu2Pf7e92d1X1Zg==
Document Description	15_NEO-0002 UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	121.86kB (1523206 bits)
Date Submitted	2016-12-11 00:00:00
Date Available	2016-12-11 00:00:00
Creation Date	2016-12-02 08:48:17
Producing Software	Mac OS X 10.12.1 Quartz PDFContext
Document Lastmod	2016-12-02 16:55:15
Document Title	Microsoft Word - ChargeSpot installation guide 2016.docx
Document Creator	Word

ChargeSpot - Quick Start Guide
Review safety information in manual before installation!
Step 1/7
Mill a recessed hole that is 3½” in diameter from the underside of the substrate to
within 1/8” of the surface.
Step 2/7
Attach the three appropriate no.8 screws to the bottom of the charger as seen. Ensure
that the screws are not tightly fastened to leave room for depth adjustment.
All rights reserved by Neosen Energy LLC, 2016
Step 3/7
With the no.8 screws attached, place the charger on top of the mounting plate so that
the screws are aligned with the sockets on the mounting plate.
Step 4/7
Connect the provided power supply to the socket at the terminal point circled below.
Step 5/7
From the underside of the substrate, place the charger with the attached mounting
plate into the recessed hole. If the mounting plate is not flush against the underside, use
a Philips head screwdriver to loosen the no.8 screws until flush. Note that the
transmitter MUST sit flush against the underside to operate properly.
All rights reserved by Neosen Energy LLC, 2016
Step 6/7
Secure the mounting plate to the substrate with three no.6 screws (provided). Ensure
that the screws do not penetrate the substrate surface.
Step 7/7
Place the decal directly on top of where the charger was installed to mark the
designated charging area.
Optional
Zip ties can be applied at three (3) points on the mounting plate to tether excess cable
to the device (see arrows above).
All rights reserved by Neosen Energy LLC, 2016
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
PDF Version                     : 1.4
XMP Toolkit                     : 3.1-701
Create Date                     : 2016:12:02 08:48:17Z
Creator Tool                    : Word
Modify Date                     : 2016:12:02 16:55:15+08:00
Metadata Date                   : 2016:12:02 16:55:15+08:00
Keywords                        : 
Producer                        : Mac OS X 10.12.1 Quartz PDFContext
Format                          : application/pdf
Title                           : Microsoft Word - ChargeSpot installation guide 2016.docx
Document ID                     : uuid:90c64216-c9b7-4927-a57f-ce45a194fefe
Instance ID                     : uuid:a8bea80d-cece-4af8-85e0-9223ea06ee75
Page Count                      : 4
Creator                         : Word

EXIF Metadata provided by EXIF.tools