NETIS SYSTEMS 3GC101R 150Mbps Wireless-N 3G Broadband Router User Manual manual
NETIS SYSTEMS CO., LTD. 150Mbps Wireless-N 3G Broadband Router manual
manual
netis Wireless-N 3G Router
User Manual
V1.1
2011-06-02
Wireless-N 3G Router User Manual
1 / 69
Certification
FCC CE
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance could void the user‟s authority to operate this equipment. (Example- use
only shielded interface cables when connecting to computer or peripheral devices)
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution! The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user authority
to operate the equipment
Wireless-N 3G Router User Manual
2 / 69
Package Contents
The following items should be found in your package:
Wireless-N 3G Router
Power adapter
Quick Installation Guide
Make sure that the package contains above items. If any of the above items is missing or damaged,
please contact the store you bought this product from.
Brand and Copyright Announcement
Copyright © 2010 Netis Corporation.
All rights reserved
is a registered trademark of Netis Corporation. Other trademarks and trade
names may be used in this document to refer to either the entities claiming the marks and
names or their products.
Reproduction in any manner without the permission of Netis Corporation is strictly forbidden
All the information in this document is subject to change without notice.
Wireless-N 3G Router User Manual
3 / 69
Contents
1. INTRODUCTION ................................................................................................................................... 6
1.1. PRODUCT OVERVIEW ......................................................................................................................... 6
1.2. MAIN FEATURES ............................................................................................................................... 6
1.3. SUPPORTING STANDARD AND PROTOCOL ................................................................................................ 7
1.4. WORKING ENVIRONMENT................................................................................................................... 7
2. HARDWARE INSTALLATION .................................................................................................................. 8
2.1. SYSTEM REQUIREMENT ...................................................................................................................... 8
2.2. PANEL ............................................................................................................................................ 8
2.3. RESTORE TO FACTORY CONFIGURATION .................................................................................................. 9
2.4. HARDWARE INSTALLATION PROCEDURES ............................................................................................... 10
3. LOGIN ................................................................................................................................................ 11
3.1. CONFIGURE COMPUTER ................................................................................................................... 11
3.1.1. Windows 98/Me ................................................................................................................ 11
3.1.2. Windows 2000 ................................................................................................................... 12
3.1.3. Windows XP ...................................................................................................................... 15
3.1.4. Windows Vista/7 ............................................................................................................... 18
3.1.5. MAC OS ............................................................................................................................. 22
3.2. CHECKING CONNECTION WITH THE ROUTER .......................................................................................... 24
3.3. LOGIN .......................................................................................................................................... 25
4. SYSTEM CONFIGURATION .................................................................................................................. 27
4.1. CONVENIENT SETUP ........................................................................................................................ 27
4.1.1. DHCP user (Cable Modem) ................................................................................................. 27
4.1.2. PPPoE user (ADSL).............................................................................................................. 28
4.1.3. Static User ......................................................................................................................... 29
4.1.4. PPTP Client + DHCP ............................................................................................................ 30
4.1.5. 3G User ............................................................................................................................. 31
4.1.6. Wireless Configuration....................................................................................................... 31
4.2. SYSTEM INFORMATION ..................................................................................................................... 32
4.2.1. Internet Access .................................................................................................................. 32
4.2.2. LAN Info ............................................................................................................................ 33
4.2.3. Wireless Info ...................................................................................................................... 34
4.2.4. Secondary AP..................................................................................................................... 34
4.2.5. System ............................................................................................................................... 35
4.2.6. Statistics ............................................................................................................................ 35
4.3. SYSTEM LOG .................................................................................................................................. 36
4.3.1. Connection Logs ................................................................................................................ 36
4.3.2. 3G Logs ............................................................................................................................. 36
Wireless-N 3G Router User Manual
4 / 69
4.4. INTERNET SETUP............................................................................................................................. 36
4.4.1. DHCP User (Cable Modem) ................................................................................................ 37
4.4.2. PPPoE user (ADSL).............................................................................................................. 38
4.4.3. Static user ......................................................................................................................... 39
4.4.4. PPTP Client + DHCP ............................................................................................................ 40
4.4.5. 3G User ............................................................................................................................. 41
4.5. WIRELESS MANAGEMENT ................................................................................................................. 42
4.5.1. Wireless Setup ................................................................................................................... 42
4.5.1.1. Basic ........................................................................................................................................... 42
4.5.1.2. Security ....................................................................................................................................... 43
4.5.1.3. WDS............................................................................................................................................ 46
4.5.1.4. Host Filter ................................................................................................................................... 48
4.5.1.5. Host List ...................................................................................................................................... 48
4.5.1.6. WPS ............................................................................................................................................ 49
4.5.1.7. Advanced .................................................................................................................................... 50
4.5.1. Multiple AP Setup .............................................................................................................. 51
4.5.1.1. Basic ........................................................................................................................................... 52
4.5.1.2. Security ....................................................................................................................................... 52
4.5.1.3. Host List ...................................................................................................................................... 52
4.6. SECURITY SETUP ............................................................................................................................. 52
4.6.1. MAC Filter ......................................................................................................................... 53
4.6.2. Internet Access Control ...................................................................................................... 54
4.6.3. DNS Filter .......................................................................................................................... 55
4.7. QOS SETUP .................................................................................................................................. 56
4.8. LAN SETUP ................................................................................................................................... 57
4.8.1. LAN IP Address .................................................................................................................. 57
4.8.2. DHCP Server ...................................................................................................................... 57
4.8.3. DHCP Client Info ................................................................................................................ 58
4.9. APPLICATIONS & GAME.................................................................................................................... 58
4.9.1. Virtual Service ................................................................................................................... 59
4.9.2. DMZ Setting ...................................................................................................................... 60
4.9.3. UPNP ................................................................................................................................. 60
4.9.4. Port Trigger ....................................................................................................................... 61
4.10. APPLICATION GATEWAY .................................................................................................................... 61
4.11. DDNS ......................................................................................................................................... 62
4.12. ROUTING ...................................................................................................................................... 63
4.13. SYSTEM MANAGEMENT ................................................................................................................... 63
4.13.1. Password Setup ................................................................................................................. 64
4.13.2. Web Setup ......................................................................................................................... 64
4.13.3. Upgrade ............................................................................................................................ 64
4.13.4. Reboot............................................................................................................................... 65
4.13.5. Restore .............................................................................................................................. 65
Wireless-N 3G Router User Manual
5 / 69
4.13.6. WOL .................................................................................................................................. 65
4.13.7. System Time ...................................................................................................................... 65
5. TROUBLESHOOTING........................................................................................................................... 67
Wireless-N 3G Router User Manual
6 / 69
1. Introduction
1.1. Product Overview
The Wireless-N 3G Router supplies multiple routers, including 150Mbps router, 150Mbps traveler
router, 300Mbps router etc. The Wireless-N 3G Router is a multi-function wireless broadband router.
When connecting a 3G USB card to it, all network (wired/wireless) users can share 3G Internet
connection. The Wireless-N 3G Router can support 3G speeds up to 7.2Mbps and comes with a
built-in Ethernet WAN port for cable modem or xDSL modem. When connected to a xDSL/cable
broadband, it will enable the xDSL/cable broadband connection automatically when 3G Internet
connection is not available.
The Wireless-N 3G Router provides up to 150/300Mbps data transmission rate in 2.4GHz frequency,
complies with IEEE 802.11n, IEEE 802.11g and IEEE802.11b and backwards compatible with all
IEEE 802.11n/g/b devices. And the router also supports wireless LAN up to 128-bit WEP,
WPA/WPA2 encryption security. The Wireless-N 3G Router also provides WEB and Remote
Management and system log so that network administrators can manage and monitor the network in
real time.
The Wireless-N 3G Router also provides a hardware WPS (Wi-Fi protected setup) button, which
helps you setup a secure wireless network in a snap. The button lets you activate the wireless
protection easily
In this User Manual, if there is no specific instruction, we all use 3G-C101 for example
1.2. Main Features
Support 3G network card
Support up to 150Mbps wireless data transmit rate
Fully compliant with IEEE802.3 10 Base-T, IEEE802.3u 100 Base-TX, IEEE802.3ab
Support DHCP Client, PPPoE Client, Static IP
Support MAC filtering, IP access control, DNS filter
Support PPTP 、 L2TP and IPSEC pass through
Support UPNP (universal plug and play)
Wireless-N 3G Router User Manual
7 / 69
Upgradeable firmware for future functions
WPS button can setup a secure network easily
Support data encryption mode: WEP, WPA, WPA2
Support multiple BSSID
Support DMZ
1.3. Supporting Standard and Protocol
IEEE 802.11b/g/n
IEEE 802.11e, IEEE 802.11i
IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,
1.4. Working Environment
Temperature
0° to 40° C (operating)
-40° to 70° C (storage)
Humidity
10% to 90 % non-condensing (operating)
5% to 90% non-condensing (storage)
Power
DC 5V
Wireless-N 3G Router User Manual
8 / 69
2. Hardware Installation
2.1. System Requirement
Minimum Requirements:
Broadband (DSL/Cable) modem and service with Ethernet port
802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer
Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher
2.2. Panel
Front panel
Figure 2-1
LED
Function
PWR
ON
Power on
OFF
Power off
CPU
ON
System Start
Flashing
Normal
OFF
System OFF
USB
ON
USB card connection normal
OFF
USB card connection abnormal
WAN
ON
WAN Connection normal
Flashing
Data transmitting
OFF
WAN Connection abnormal
Wireless-N 3G Router User Manual
9 / 69
LAN1-LAN4
ON
LAN Connection normal
Flashing
Data transmitting
OFF
LAN Connection abnormal
WLAN
Flashing
Wireless data transmitting
OFF
Wireless off
WPS
Flashing
slowly
WPS is running
OFF
WPS is not running
Rear panel
Figure 2-2
Description
Function
PWR port
Connect to Power adapter, please don‟t use the unknown
power adapter, otherwise your device may be damaged.
PWR
Turn on /off the router
USB
3G card is connected to this port
LAN port
Connect with computer NIC or Ethernet device
WAN port
Internet access
WPS
Please refer to WPS
2.3. Restore to Factory Configuration
If the router ever freezes in a setting change process or if you can‟t access it because you can‟t
remember the IP you have given it or other problem, you may have to utilize the reset button on the
back of the router to put it back to factory settings. You have to press and hold this button for a few
seconds (2-6s) with a pencil when it is working, then release and it will restore settings to the factory
configuration.
The other way to restore factory settings is through the same user interface used in setup. Click on
Wireless-N 3G Router User Manual
10 / 69
„System management‟- „Restore‟, and click on the „Restore‟ button.
2.4. Hardware Installation Procedures
Figure 2-3
Attach one end of an Ethernet cable to your computer‟s Ethernet port, and the other end to one of
the LAN ports of your router.
Connect another Ethernet cable from your Cable/DSL modem to the WAN port of your router.
Connect the single DC output connector of the power adapter to the power jack on the back of
the router and plug the Power Adapter into an AC outlet.
Wireless-N 3G Router User Manual
11 / 69
3. Login
You can manage the Wireless-N 3G Router through the Web browser-based configuration utility.
To configure the device via Web browser, at least one properly configured computer must be
connected to the device via Ethernet or wireless network. The Wireless-N 3G Router is configured
with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0 and its DHCP server
is enabled by default. Before setting up the Router, make sure your PCs are configured to obtain an
IP address automatically from the Router by the steps below.
3.1. Configure Computer
3.1.1. Windows 98/Me
1. Go to Start Settings Control Panel.
2. Find and double-click the Network icon. The Network dialog box appears.
3. Click the Configuration label and ensure that you have network card.
4. Select TCP/IP. If TCP/IP appears more than once, please select the item that has an arrow “”
pointing to the network card installed on your computer. DO NOT choose the instance of TCP/IP with
the words “Dial Up Adapter” beside it.
5. Click Properties. The TCP/IP Properties dialog box appears.
6. Ensure the Obtain IP Address Automatically is checked.
7. From the WINS Configuration dialog box, Ensure that Disable WINS Resolution is checked.
8. From the Gateway dialog box, remove all entries from the Installed gateways by selecting them and
clicking Remove.
9. From the DNS Configuration dialog box, remove all entries from the DNS Server Search Order
box by selecting them and clicking Remove. Remove all entries from the Domain Suffix Search
Order box by selecting them and clicking Remove. Click Disable DNS.
10. Click OK, back to Network Configuration dialog box
11. Click OK, if prompted to restart, click YES.
Wireless-N 3G Router User Manual
12 / 69
3.1.2. Windows 2000
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
Figure 3-1
2. Double click the icon Network and Dial-up Connections
3. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Wireless-N 3G Router User Manual
13 / 69
Figure 3-2
4. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-3
5. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then
press OK to close the Internet Protocol (TCP/IP) Properties window
Wireless-N 3G Router User Manual
14 / 69
Figure 3-4
6. Press OK to close the Local Area Connection Properties window
Figure 3-5
Wireless-N 3G Router User Manual
15 / 69
3.1.3. Windows XP
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
2. Click Network and Internet Connections
Figure 3-6
3. Click Network Connections
Figure 3-7
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Wireless-N 3G Router User Manual
16 / 69
Figure 3-8
5. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-9
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then
press OK to close the Internet Protocol (TCP/IP) Properties window
Wireless-N 3G Router User Manual
17 / 69
Figure 3-10
7. Press OK to close the Local Area Connection Properties window
Figure 3-11
Wireless-N 3G Router User Manual
18 / 69
3.1.4. Windows Vista/7
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
2. Click Network and Sharing Center
Figure 3-12
3. Click Manage Network Connections
Figure 3-13
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Wireless-N 3G Router User Manual
19 / 69
Figure 3-14
5. Highlight Internet Protocol Version 4 (TCP/IP) and then press Properties button
Wireless-N 3G Router User Manual
20 / 69
Figure 3-15
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and then
press OK to close the Internet Protocol (TCP/IP) Properties window
Wireless-N 3G Router User Manual
21 / 69
Figure 3-16
7. Press OK to close the Local Area Connection Properties window
Wireless-N 3G Router User Manual
22 / 69
Figure 3-17
3.1.5. MAC OS
Please follow the steps blow to setup your computer:
1. Go to Start→ System preference Settings→ Network.
Wireless-N 3G Router User Manual
23 / 69
Figure 3-18
2. Click Network, Select Use DHCP at the Configuration bar, the system will get the IP address
automatically.
Figure 3-19
Wireless-N 3G Router User Manual
24 / 69
3. Press Apply to complete this operation and close the window.
3.2. Checking Connection with the Router
After configuring the TCP/IP protocol, use the ping command to verify if the computer can
communicate with the Router. To execute the ping command, open the DOS window and Ping the IP
address of the Wireless-N 3G Broadband Router at the DOS prompt:
For Windows 98/Me: Start -> Run. Type command and click OK.
For Windows 2000/XP: Start -> Run. Type cmd and click OK.
For Windows Vista/7:Start→ Type cmd at the start search bar and press the Enter.
For MAC OS→ The system will complete this operation automatically.
At the DOS prompt, type the following command:
The Command window should return something similar to the following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 1ms, Average = 1ms
If the computer fails to connect to the router, the Command window will return the following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Wireless-N 3G Router User Manual
25 / 69
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Verify your computer's network settings are correct and check the cable connection between the
router and the computer.
3.3. Login
Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just connected to
the router, type http://192.168.1.1 in the address bar, and press enter
Figure 3-20
In the pop-up window, enter the user name guest and password guest and then click OK
Wireless-N 3G Router User Manual
26 / 69
Figure 3-21
Login successfully and the home page appears, the left navigation bar shows the main options to
configure the system, the right screen is the summary information for viewing the configurations.
Figure 3-22
Wireless-N 3G Router User Manual
27 / 69
4. System Configuration
4.1. Convenient Setup
Providing you the convenient and simplest method for configure the router, the purpose of this item is
to provide an easy way for you to use it and configure your router to access the Internet quickly;
including „DHCP‟, „PPPoE‟, „Static IP‟, „PPTP Client + DHCP‟, „3G user‟ and „Wireless
Configuration‟. This is the most convenient tool for you to configure router.
4.1.1. DHCP user (Cable Modem)
Figure 4-1
After select this item, you will obtain an IP address from your ISP automatically, those ISP who
supply Cable modem always use DHCP technology.
Wireless-N 3G Router User Manual
28 / 69
4.1.2. PPPoE user (ADSL)
Figure 4-2
If your ISP provides you the PPPoE service (all ISP with DSL transaction will supply this service,
such as the most popular ADSL technique), please select this item. In the “Convenient configuration”
You can input your PPPoE username and password to access the Internet.
PPPoE username: Input PPPoE username provided by ISP
PPPoE Password: Input PPPoE password provided by ISP.
Wireless-N 3G Router User Manual
29 / 69
4.1.3. Static User
Figure 4-3
This item should only be used when users use a static IP address to access Internet, you should input
your “WAN IP address”, ”subnet mask”,” default gateway” and “DNS server (domain name server)
IP address” according to the information provided by your ISP. And every IP address should be input
in appropriate IP field, a IP address only divided into four IP octets by sign”.” is acceptable.
WAN IP address: The IP address that your Internet access into
Subnet mask: Specify a Subnet Mask for your WAN segment
Default gateway: It is provided by your ISP
Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you with at
least one DNS IP address, input IP address of your DNS server in this field
Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank.
Wireless-N 3G Router User Manual
30 / 69
4.1.4. PPTP Client + DHCP
Figure 4-4
This item should be used when users use a PPTP client as well as a DHCP to access Internet, you
should input the information that you get from your ISP
Wireless-N 3G Router User Manual
31 / 69
4.1.5. 3G User
Figure 4-5
ISP: Select ISP of your 3G card
3G card type: Select your 3G card type
4.1.6. Wireless Configuration
Figure 4-6
You can choose “Enable” or “Disable” to enable or disable the wireless function. The default setting
is “enable”. If you chose the “Disable” status, the router will become a wired broadband router
without wireless function, so be careful when you choose this status.
SSID: SSID (Service Set Identifier) is your wireless network's name shared among all points in a
Wireless-N 3G Router User Manual
32 / 69
wireless network. The SSID must be identical for all devices in the wireless network. It is
case-sensitive and must not exceed 32 characters.
4.2. System Information
This page indicate current status of the router, including „Internet Access‟, „LAN Info‟, „Wireless
Info‟, „Secondary AP‟, „System‟ and „Statistics‟ about the bits router send and received .This item is
used for monitor the current status of router for administrator, and also supplies help information
about judge working situation of router
4.2.1. Internet Access
Figure 4-7
This feature provides running status information of the WAN port (the port connect to the Internet)
Connection Type: Display router‟s current connection type, it depends on what kind of
connection type your ISP provides.
Physical Address: The physical address of WAN port, this is a unique address assigned by
manufacturer.
IP Address: The IP address you obtained after connect to the Internet, if you haven‟t connected
to the Internet yet, this field is 0.0.0.0.
Subnet Mask: The Subnet mask you obtained after connect to the Internet, if you haven‟t
connected to Internet yet, this field is 0.0.0.0
Default Gateway: The IP address of Default gateway you obtained after connect to the Internet,
Wireless-N 3G Router User Manual
33 / 69
if you haven‟t connected to Internet yet, this field is 0.0.0.0.
Primary DNS: The DNS server translates domain or website names into IP address, input the
most common DNS server address you used or provided by your ISP.
Secondary DNS: Input IP address of a backup DNS server or you can leave this field blank
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is
not in accord with the value ISP provide, it may causes some problems, such as fail to send Email,
or fail to browse website. So if that happen, you can contact your ISP for more information and
correct your router‟s MTU value
Current version: The version information of your current firmware
4.2.2. LAN Info
Figure 4-8
This item provides information about router‟s LAN port, display LAN port‟s physical address, IP
address and current situation of DHCP server.
Wireless-N 3G Router User Manual
34 / 69
4.2.3. Wireless Info
Figure 4-9
This item provides current running information of wireless.
Wireless status: Display wireless interface status is enabled or not
Wireless Mode: Current wireless mode of wireless router
Channel: Display current channel of your wireless router.
SSID: SSID (Service Set Identifier) is your wireless network's name shared among all points in a
wireless network.
Wireless Interface MAC Address: The MAC address is used for wireless communication
SSID Broadcasting: You can select “enable” or “disable” to enable or disable the broadcast
SSID function, If the setting of this field is disable, wireless client can‟t obtain this SSID to login
in, then user have to input the SSID value manually
Security Mode: Display whether your security wireless function have been applied.
4.2.4. Secondary AP
Figure 4-10
Wireless-N 3G Router User Manual
35 / 69
This item provides current running information of Secondary AP
Wireless status: Display wireless interface status is enabled or not
Wireless Mode: Current wireless mode of wireless router
Channel: Display current channel of your wireless router.
SSID: SSID (Service Set Identifier) is your wireless network's name shared among all points in a
wireless network.
Wireless Interface MAC Address: The MAC address is used for wireless communication
SSID Broadcasting: You can select “enable” or “disable” to enable or disable the broadcast
SSID function, If the setting of this field is disable, wireless client can‟t obtain this SSID to login
in, then user have to input the SSID value manually
Security Mode: Display whether your security wireless function have been applied.
4.2.5. System
Figure 4-11
This item provides current running information of System
4.2.6. Statistics
Figure 4-12
This item provides statistics information about the bits router sends and received
Wireless-N 3G Router User Manual
36 / 69
4.3. System Log
4.3.1. Connection Logs
Figure 4-13
Examine system log, there are most ten logs can be showed in one Page
4.3.2. 3G Logs
Figure 4-14
Display 3G connection logs. You can configure items show in every single page
4.4. Internet Setup
The purpose of this item is to provide an easy way for you to use it and configure your router to access
the Internet quickly
Wireless-N 3G Router User Manual
37 / 69
4.4.1. DHCP User (Cable Modem)
After select this item, you will obtain an IP address from your ISP automatically, those ISP who
supply Cable modem always use DHCP
Figure 4-15
Clone MAC address: The WAN port of router has a unique MAC address assigned by
manufacturer; it called as “Default MAC”. The “Clone MAC” is used for some special situations;
For example, ISP only allows certain MAC address to access the Internet, thus you can modify
your WAN port‟s MAC address in accord with the requirement of ISP, avoiding ISP‟s detection
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is
not in accord with the value ISP provide, it may causes some problems, such as fail to send Email,
or fail to browse website. So if that happened, you can contact your ISP for more information and
correct your router‟s MTU value
Primary DNS: DNS server is used for resolve domain name. Your ISP will provide you with at
least one DNS IP address, input IP address of your DNS server in this field
Secondary DNS: Input IP address of backup DNS server or you can leave this field blank
Wireless-N 3G Router User Manual
38 / 69
4.4.2. PPPoE user (ADSL)
Figure 4-16
If your ISP provides you the PPPoE service (all ISP with DSL transaction will supply this service,
such as the most popular ADSL technique), please select this item. In the “Convenient Setup” You
can input your PPPoE username and password to access the Internet
PPPoE username: Input PPPoE username provided by ISP
PPPoE Password: Input PPPoE password provided by ISP
Default MAC Address: The MAC address of WAN port, this is a fixed, unique address assigned
by manufacturer
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is
not in accord with the value ISP provide, it may causes some problems, such as fail to send Email,
or fail to browse website. So if that happened, you can contact your ISP for more information and
correct your router‟s MTU value
Primary DNS: DNS server is used for resolve domain name. Your ISP will provide you with at
least one DNS IP address, input IP address of your DNS server in this field
Wireless-N 3G Router User Manual
39 / 69
Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank
You can select three modes: connect to Internet automatically (Default), auto disconnect when idle or
time out, connect to Internet manually
4.4.3. Static user
Figure 4-17
This should be used only you are connecting through a static IP address. You should input your
“WAN IP address”, ”subnet mask”,” default gateway” and “DNS server (domain name server) IP
address” according to the information provided by your ISP. And IP address input should be filled in
appropriate IP field, a IP address only divided into four IP octets by sign”.” is acceptable
WAN IP address: The IP address that your Internet access into
Subnet mask: Specify a Subnet Mask for your WAN segment
Default gateway: It is provided by your ISP
Clone MAC address: The WAN port of router has a unique MAC address assigned by
manufacturer; it called as “Default MAC”. The “Clone MAC” is used for some special situations;
For example, ISP only allows certain MAC address to access the Internet, thus you can modify
your WAN port‟s MAC address in accord with the requirement of ISP, avoiding ISP‟s detection
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
Wireless-N 3G Router User Manual
40 / 69
MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is
not in accord with the value ISP provide, it may causes some problems, such as fail to send Email,
or fail to browse website. So if that happened, you can contact your ISP for more information and
correct your router‟s MTU value
Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you with at
least one DNS IP address, input IP address of your DNS server in this field
Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank.
4.4.4. PPTP Client + DHCP
Figure 4-18
Server: Enter server IP address
User ID: Input user ID
Password: Input: password
Clone MAC address: The WAN port of router has a unique MAC address assigned by
manufacturer; it called as “Default MAC”. The “Clone MAC” is used for some special situations;
Wireless-N 3G Router User Manual
41 / 69
For example, ISP only allows certain MAC address to access the Internet, thus you can modify
your WAN port‟s MAC address in accord with the requirement of ISP, avoiding ISP‟s detection
MTU: The MTU (Maximum Transmission Unit) setting specifies the largest packet size
permitted for network transmission. Most DSL users should use the value 1492.You can set
MTU manually, and you should leave this value in the 1200 to 1500 range. If the value you set is
not in accord with the value ISP provide, it may causes some problems, such as fail to send Email,
or fail to browse website. So if that happened, you can contact your ISP for more information and
correct your router‟s MTU value
Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you with at
least one DNS IP address, input IP address of your DNS server in this field
Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank.
4.4.5. 3G User
Figure 4-19`
ISP: Select ISP of your 3G card
3G card type: Select the 3G card type that you are using
Wireless-N 3G Router User Manual
42 / 69
User name & password: Input username and password
Primary DNS: DNS server is used for resolve domain name. Your ISP will provides you with at
least one DNS IP address, input IP address of your DNS server in this field
Secondary DNS: Input IP address of backup DNS server, or you can leave this field blank.
4.5. Wireless Management
4.5.1. Wireless Setup
It contains the following parts: Basic, Security, WDS, Host Filter, Host List, WPS and Advanced
4.5.1.1. Basic
Providing basic configuration items for wireless router users, including ”wireless network
status”, ”Radio Band”, ”Radio Mode”, ”SSID”, ”SSID broadcasting”, ”Channel width”, “Region”
and ”Channel” basic configuration items.
Figure 4-20
Wireless network status: You can choose “enable” or “disable” to enable or disable the “Wireless
Network Status”, if what you choose is “Disable”, the AP function of wireless router will be
turned off
Radio band: You can select the wireless standards running on your network, if you have
Wireless-N, and Wireless-B/G devices in your network, keep the default setting, 802.11b+g+n
Wireless-N 3G Router User Manual
43 / 69
Radio mode: You can select radio mode of wireless router, the default setting is AP mode
SSID: The default is default
SSID Broadcasting: You can select “enable” or “disable” to enable or disable the broadcast SSID
function, If the setting of this field is disable, wireless client can‟t obtain this SSID to login in,
then user have to input the SSID value manually
Channel width: This switch allows you to set Router's wireless bandwidth. 20MHz: In this mode
you can get low bandwidth, little interference and slow rate. 40MHz: In this mode you can get
high bandwidth, high interference and rapid rate. Use only when you have a pure router, draft
802.11n wireless network
Channel sideband: It controls your wireless router use higher or lower channel when working on
40MHz
Region: You can select the region where you live in
Channel: In 20MHz, you can select one channel from 1 to 14 manually, and in 40MHz, you can
select one channel from 1 to 9 or 5 to 13, which provides a choice of avoiding interference
4.5.1.2. Security
The item allows you to encrypt your wireless communication, and you can also protect your wireless
network from unauthorized user access. It supplies “None”, “WEP”, “WPA-PSK”, “WPA2-PSK”
and “WPA/WPA2-PSK” five different encryption modes.
None
“None”means do not encrypt wireless data
Figure 4-21
WEP
Wireless-N 3G Router User Manual
44 / 69
Figure 4-22
Key Length: There are two basic levels of WEP encryption, 64 bits and 128 bits, the more bits
password have, the better security wireless network is, at the same time the speed of wireless is
more slower.
Key Mode: If you select WEP to encrypt your data, choose the bits of password, it should be
64 bits or 128 bits. Then choose the format of password; it should be HEX or ASCII. The valid
character for HEX format should be numbers from 0 to 9 and letters from A to F. HEX support
mixed letter and number mode. And ASCII supports all characters that in keyboard.
Key Length description: When you select 64bits, you need to input 10 chars for HEX and 5
chars for ASCII, and when you select 128bits, you need to input 26 chars for HEX and 13
chars for ASCII.
Note: When the WPS is enabled, please not use WEP.
WPA-PSK
Figure 4-23
Encryption type: You can select the algorithm you want to use, TKIP, AES or TKIP&AES.
Wireless-N 3G Router User Manual
45 / 69
TKIP means “Temporal Key Integrity Protocol”, which incorporates Message Integrity Code
(MIC) to provide protection against hackers. AES, means “Advanced Encryption System”,
which utilizes a symmetric 128-Bit block data.
Key Renewal: you can configure the renewal time between 60 to 86400 seconds.
Key Length description: you need to input 8 to 63 ASCII characters no matter which type you
select.
WPA2-PSK
Figure 4-24
The WPA2-PSK is similar to WPA-PSK and with stronger encryption method than WPA-PSK, using
WPA2-PSK; you should input password (leave this value in the range of 8 to 63 characters) and key
renewal time (leave this value in the range of 60 to 86400 seconds).
WPA/WPA2-PSK
Figure 4-25
This item mixed WPA-PSK and WPA2-PSK mode, which provides higher security level; you can
Wireless-N 3G Router User Manual
46 / 69
configure it according with WPA-PSK or WPA2-PSK
4.5.1.3. WDS
Figure 4-26
If you have selected WDS or AP+WDS mode in Wireless Basic-Radio Mode, please do the following
configurations
WDS Name: Give a description of your wireless bridge to tell apart
WDS MAC Address: If the current working mode is “WDS” or “AP+WDS”, then you need to
configure wireless bridge configuration. Enter MAC address of remote access point, at the
same time the remote access point also need to configure to “WDS” or ”AP+WDS” mode
Current WDS Information: It illustrates basic information of all wireless bridge that in
connection status, you may delete unnecessary bridge.
AP1:
Wireless-N 3G Router User Manual
47 / 69
Select radio mode is WDS or AP+WDS in wireless management-basic of AP1.
Click on „Wireless Management‟- „AP Setup‟- „Security‟ and select and save None as
authentication type.
Click on „Wireless Management‟- „AP Setup‟- „Security‟ and select and save None as WDS
authentication type or select a WDS security type, enter key and save.
Input WDS name (e.g.: default), input MAC address of AP2 (00-22-4f-bc-af-5d), click add,
then the record named default will appears in WDS list.
Select Channel is „Channel 6‟in wireless management-basic of AP2.
AP2:
Select radio mode is WDS or AP+WDS in wireless management-basic of AP2.
The IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).
Select „LAN setup‟ -„DHCP‟ server‟ , select disable DHCP server.
4. Input WDS name (e.g.: Default), input MAC address of AP1 (00-22-4f-cc-ae-f5), click add,
then the record named Default will appears in WDS list.
Select Channel is „Channel 6‟in wireless management-basic of AP2.
Note: Before you setup WDS connection, please make sure that AP1 and AP2 is in the same network,
that is if the IP address of AP1 is 192.168.1.1, then the IP address of AP2 should be 192.168.1.x
(1<x<255,e.g.: x=8).
Wireless-N 3G Router User Manual
48 / 69
4.5.1.4. Host Filter
Figure 4-27
Wireless Access Control Status: the default is disable. To disable “Wireless Access Control
Status”, keep the default setting “Disable”
Please select “enable” if you want to configure Wireless Access Control, then you can follow the
following steps to set:
1. Add MAC address you want to control in the “MAC address” field (the format is
**-**-**-**-**-**), then click “Add” button, and you will see the MAC address has displayed in the
MAC list.
2. There are two items supplied, “Permit wireless connection for MAC address listed (others are
Denied)” and “Deny wireless connection for MAC address listed (others are Permitted)”, Select the
item you want, and click “Save” button
4.5.1.5. Host List
Figure 4-28
Display current status of the wireless client associate with AP
Wireless-N 3G Router User Manual
49 / 69
4.5.1.6. WPS
Wi-Fi Protect Setup (WPS) function can let you create a safety network easily. You can through „PIN
Input Config (PIN)‟ or ‟Push Button (PBC)‟to encrypt your network. This router also provides WPS
button, you only need to push the WPS button in this router and the wireless network card which
support WPS function, then the router will be encrypted to WPA2-AES mode automatically.
Note:
If you have configured encryption mode in your router, then when you use this WPS function, please
configure the authentication type to None, then it will be encrypted to WPA2-AES mode
automatically. If you don‟t want to change your authentication type, then when you use this function,
the router will be encrypted to the mode that you have configured.
Figure 4-29
WPS Status: you can use this function to setup the wireless connection between this router and
wireless network card. The default is enable.
AP PIN Code: this code can mark a wireless product
Wireless Host PIN Code: input the PIN of wireless network card that support WPS function.
Click connect, when it connect successfully, it will be encrypted to WPA2-PSK
WPS PBC settings: Click connect, when it connect successfully, it will be encrypted to
WPA2-PSK
WPS can connect the wireless adapter and the router in a safe way. If you have a wireless network
card which has WPS button, you may set up a safe network via the following methods
Method 1: Button
Wireless-N 3G Router User Manual
50 / 69
Push and hold WPS button on back of Router until WPS LED flashes or for about 3seconds
Push WPS button on wireless network adapter and hold for about 3-5 seconds
A safe connection will be established automatically in a moment
The reverse – pushing and holding WPS button on adapter briefly, then pushing and holding
WPS button on router briefly – may also be utilized
Method 2: PIN
Select this router for connection in your OS network connections or wireless adapter
software settings
Choose to enter the WPS PIN of the router and provide default router WPS PIN printed on
label on bottom of router. This PIN may be changed though, and you may do so/confirm
current PIN in the router's user interface – click „Wireless Management‟- „Wireless Setup‟ -
„WPS‟ and you will be able to see the AP PIN as well as generate a new one and save it
Alternatively, you may choose to utilize a WPS PIN provided by your wireless adapter and
enter it in the router in the same part of the user interface - click „Wireless Management‟-
„Wireless Setup‟ - „WPS‟ and enter adapter PIN for „AP PIN Code‟.
4.5.1.7. Advanced
Figure 4-30
Wireless-N 3G Router User Manual
51 / 69
These settings are only for more technically advanced users who have a sufficient knowledge about
wireless LAN. These settings should not be changed unless you know what effect the change will
have on your AP
Authentications type: The default is set to “Auto”, which allows “Open System” or “Shared Key”
authentication to be used. Select “Shared Key” if you only want to use “Shared Key”
authentication (the sender and recipient use a WEP key for authentication)
Beacon Interval: The interval time of this Wireless-N 3G Router broadcast a beacon. Beacon is
used to synchronize the wireless network. The valid interval is 20-1000, the default is 100
RTS Threshold: You can set RTS Threshold value in this field, the valid range should be
256-2347 and default value is 2347. If a network packet is smaller than the preset RTS threshold
size, the RTS/CTS mechanism will not be enabled
Aggregation: You can accelerate the wireless transmission speed by enabling the aggregation
function. The default is AMPDU＋AMSDU
Fragmentation Threshold: It specifies the maximum size of packet during the fragmentation of
data to be transmitted
Transmission Rate: Transmit rate indicates the transmission speed of wireless LAN access .The
default setting is “Auto” and you can set this value between 1-54Mbps range
ShortGi: You can select “Enable” or “disable” for shortgi
Protection: Using 802.11b and 802.11g mixed mode may result in poor network performance.
By enabling 802.11 protection, it will ameliorate performance of 802.11g devices in your
wireless network
Preamble Type: "Short Preamble" is suitable for heavy traffic wireless network. "Long
Preamble" provides much communication reliability; the default setting is "Long Preamble”
WLAN Partition: You could choose “Enable” or “Disable”
RF Output Power:You could choose the suited power. The higher power ,the wider override
4.5.1. Multiple AP Setup
Because of the privilege, the secondary AP only can setup SSID and Security.
Wireless-N 3G Router User Manual
52 / 69
4.5.1.1. Basic
Figure 4-31
The default status of secondary AP is disable, you can select enable to enable the secondary AP.
Please refer to Basic for details
4.5.1.2. Security
Figure 4-32
Please refer to Security for details
4.5.1.3. Host List
Figure 4-33
Display current status of the wireless client associate with the secondary AP
4.6. Security Setup
This feature provides security and network protection by using “MAC Filter”, “Internet access
Wireless-N 3G Router User Manual
53 / 69
control” and “DNS Filter”
4.6.1. MAC Filter
Figure 4-34
MAC Filter Status: the default is disable. You can filter wired users by enabling this function;
thus unauthorized users can not access the network
Description: describe MAC Filter list to tell from different MAC Filter lists
Rule: you can select permit or deny. The default is permit. If you select deny ,and you can‟t
connect the router in the corresponding time
MAC address: Input the MAC address that you want to control. The default format is
**-**-**-**-**-**（e.g.: 00-22-33-da-cc-bb）
Follow the following steps to set MAC filter:
1. Enable MAC Filter, then select save.
2. Add MAC address you want to control in the “MAC address” field (the format is
**-**-**-**-**-**), then click “Add” button, and you will see the MAC address has displayed in
the MAC list.
3. There are two items supplied, “Permit wireless connection for MAC address listed (others are
Denied)” and “Deny wireless connection for MAC address listed (others are Permitted)”, Select the
item you want, and click “Save” button.
Wireless-N 3G Router User Manual
54 / 69
4.6.2. Internet Access Control
Figure 4-35
IP Firewall Status: The default is disable. The rules of “Internet access control” based on
source IP, port number and protocol
Description: Describe IP Firewall list to tell from different IP Firewall lists
Rule: You can select permit or deny. The default is permit. If you select deny ,and you can‟t
connect the internet in the corresponding time
Source IP address: Input the source IP address that you want to control. The default format is
***.***.***.***(e.g: 192.168.2.3)
Protocol and Port: If the rule has already existed in “Protocol Template”. You can select
appropriate item and apply it. Or you can input protocol type and port number manually, click
“add” button, then the item will displayed in the list.
Follow the following steps to set Internet Access Control:
1. You can select “enable” and click “Save” to enable “IP Firewall” function. This is only the first
step , you should continued to create appropriate rules for “IP Firewall”.
2. Input description information for current access control rule in the “Description” field. Input IP
address of host you want to restrict
Wireless-N 3G Router User Manual
55 / 69
3. There are two items supplied, “Permit through the router for IP address listed, others are denied”
and “Deny through the router for IP address listed, others are permitted”, Select the item you want,
and click “Save” button
4. If you want to delete certain item on the list, select appropriate item on the list, click “delete” to
delete it
4.6.3. DNS Filter
Figure 4-36
DNS Filter Status: The default is disable. “DNS filter” is able to filter certain domain name such
as www.sina.com
Rule: You can select permit or deny. The default is permit. If you select deny ,and you can‟t
connect the web in the corresponding time
DNS Filter Key words: Input website name or Domain name in the “DNS Key Words” field,
such as www.163.com.
Follow these steps to set DNS filter:
1. You can select “enable” and click “Save” to enable “DNS Filter” function. This is only the first step,
you should continued to create appropriate rules for “DNS Filter”, permit or deny.
2. Input DNS Filter Key words, such as www.sina.com
Wireless-N 3G Router User Manual
56 / 69
3. There are two items supplied, “Permit through the router for DNS Key words listed, others are
denied” and “Deny through the router for DNS Key words listed, others are permitted”, Select the
item you want, and click “Save” button
4. If you want to delete certain item on the list, select appropriate item on the list, click “delete” to
delete it
4.7. QOS Setup
Figure 4-37
Status: You could select “Enable” or “Disable”
Automatic Uplink Speed: Router adjust uplink bandwidth automatically
Manual Uplink Speed (Kbps): User configure uplink bandwidth manually
IP Address: Set the IP address range for restricted hosts
Minimum bandwidth: setup the minimum speed of uplink and downlink bandwidth
Maximum bandwidth: setup the maximum speed of uplink and downlink bandwidth
Wireless-N 3G Router User Manual
57 / 69
4.8. LAN Setup
It includes LAN IP address, DHCP Server and DHCP Client Info. You can change the default IP
address of LAN port by using this item, after changing IP address of LAN port, the router will
restarted automatically. You can also choose enable or disable of the DHCP server, set the range of
DHCP address pools
4.8.1. LAN IP Address
Figure 4-38
The IP address of LAN port is used for access router itself by computers that connect to the router
directly; here you can set IP address you need. The IP address format is like 192.168.*.***, and
default IP address is 192.168.1.1, the default subnet mask is 255.255.255.0.
4.8.2. DHCP Server
Figure 4-39
Wireless-N 3G Router User Manual
58 / 69
DHCP Server Status: Keep the default setting “Enable”, so router is able to use DHCP function.
If a router‟s DHCP server has already existed in the network, please select “Disable”.
IP Address Pool: The IP Address pool is used for allocate IP address by DHCP server; The IP
Address pool range is also changeable
DHCP IP Address Reserving: Reserve IP address for designed physical address host. If you
want to configure a fixed IP address for some host, please input physical address and IP
address, then click add
4.8.3. DHCP Client Info
Figure 4-40
Display the state of assigned IP by DHCP Server
4.9. Applications & Game
This item provides configuration items and related templates about optimize games and applications,
including “Virtual service”, “DMZ setting”, “UPNP” and “Port Trigger”.
Wireless-N 3G Router User Manual
59 / 69
4.9.1. Virtual Service
Figure 4-41
Some games, servers, and applications (such as BT, QQ video, Edunkey, Web server) are no longer
effect when behind the NAT router, so this item provides function of port mapping from LAN to
WAN.
Description: Describe current virtual server item
Internal Host IP Address: The “Internal Host IP Address” indicates IP address of the internal
host using virtual server
Protocol: The protocol item supplies several protocols. For example, if you have web server
within LAN, you can select the HTTP template then the router will input port number 80
automatically
External Port: Input an extranet port number (the users in Internet can see these ports)
Internal Port: Input an intranet port number
Wireless-N 3G Router User Manual
60 / 69
4.9.2. DMZ Setting
Figure 4-42
DMZ opens all the ports of one computer, exposing the computer to the Internet. So it should only be
used for some special-purpose, especial for Internet online games. Using this function you can select
„DMZ‟ item and input IP address of DMZ host, then click „Save‟. For the purpose of security, we
suggested that using „Virtual service‟ instead of „DMZ setting‟
4.9.3. UPNP
Figure 4-43
The UPnP function supports load Application‟s port forward record automatically. Select “Enable” to
enable this function
Wireless-N 3G Router User Manual
61 / 69
4.9.4. Port Trigger
Figure 4-44
Port trigger module dynamically registers virtual server rules when any IP host generates the packet
from the specified trigger protocol and port. Port trigger module use forward protocol type and port
number and use the IP address of host that generates the trigger packet when it registers a rule.
Predefined Trigger Rules: select one of the Predefined Rules
Rule Name: describe one Predefined Trigger that you will configure
Trigger Protocol: you can select TCP/UDP
Trigger Port: you can select a part of ports
Forward Protocol: you can select TCP/UDP
Forward Port: you can select a part of ports
4.10. Application Gateway
VPN is commonly used for encapsulate and encrypt data across the public network. For VPN tunnel,
the router supports IPSEC pass-through, PPTP pass-through and L2TP pass-through
Wireless-N 3G Router User Manual
62 / 69
Figure 4-45
PPTP Pass-through: PPTP means the “Point to Point Tunneling Protocol”, you can select “enable”
to allow PPTP pass-through the router
L2TP Pass-through: L2TP means the “Layer 2 Tunneling Protocol”, you can select “enable” to
allow L2TP pass-through the router
IPSEC Pass-through: IPSEC (Internet Protocol Security) is a suite of protocols used to
implement secure exchange; you can select “enable” to allow IPSEC pass-through the router
4.11. DDNS
The DDNS feature allows you using domain name (not IP address) to access Internet. Before you can
use this feature, you need to register an account for DDNS service at DDNS service providers. For
more information, you can visit http://www.oray.net/Help
Figure 4-46
DDNS Status: Current status of DDNS server
DDNS Server Provider: For example, if you want to use service of “dyndns.org”, you have to
first register and accounts for it. Other DDNS service providers as the same
Username, Password, Dynamic Domain Name: After register an DDNS account from DDNS
service providers, you will get “User Name”, “Password”, ”Dynamic Domain Name”, Input
Wireless-N 3G Router User Manual
63 / 69
information in appropriate field
4.12. Routing
Most of broadband router and wireless router are using NAT mode, so this feature is designed for
most common network environment
Figure 4-47
Destination Network or IP Address: Specify a certain destination Network or IP address which
static route forward to
Subnet Mask: Subnet mask is used for distinguish Network portion and Host portion for an IP
address
Next-hop IP Address: This is an IP address of the next-hop device (and also is the gateway
address for local host) that allows forwarding data between router and remote network or host
Routing Table: You can check out all current route items, click “delete” button to delete an route
item existed in routing table
4.13. System Management
System management includes password setup, web Setup, upgrade, reboot, restore, WOL and
System time
Wireless-N 3G Router User Manual
64 / 69
4.13.1. Password Setup
Figure 4-48
The default username/password is guest/guest. To ensure the Router‟s security, it is suggested that
you change the default password to one of your choice, here enter a new password and then Re-enter
it again to confirm your new password. Click “Save” button to save settings
4.13.2. Web Setup
Figure 4-49
WEB Management Status: the default is disable. Router can be accessed on the remote site using
“Web setup”. Check the “Management Port” and enter the port number and then press “save” button
to enable web management
4.13.3. Upgrade
Figure 4-50
Click "Browse..."button and select a File to upgrade, after you have selected the appropriate file, click
"Upgrade" button to execute upgrade procedure. Do not cut off the power supply during the process
of upgrading
Wireless-N 3G Router User Manual
65 / 69
4.13.4. Reboot
Figure 4-51
Click “Restart” button to restart the router
4.13.5. Restore
Figure 4-52
Click "Restore" button, the Router will erase all of your settings and replace them with the factory
defaults, make sure you have backup current settings before click this button
4.13.6. WOL
Figure 4-53
Input host MAC address, and then click button of "Wake up" to wake up the target host which in the
LAN
4.13.7. System Time
Figure 4-54
Wireless-N 3G Router User Manual
66 / 69
You can choose the time server and the time zone for the system time
Wireless-N 3G Router User Manual
67 / 69
5. Troubleshooting
1. I cannot access the Web-based Configuration Utility from the Ethernet computer used to
configure the router.
Check that the LAN LED is on. If the LED is not on, verify that the cable for the LAN
connection is firmly connected.
Check whether the computer resides on the same subnet with the router‟s LAN IP address.
If the computer acts as a DHCP client, check whether the computer has been assigned an IP
address from the DHCP server. If not, you will need to renew the IP address.
Use the ping command to ping the router‟s LAN IP address to verify the connection.
Make sure your browser is not configured to use a proxy server.
Check that the IP address you entered is correct. If the router‟s LAN IP address has been changed,
you should enter the reassigned IP address instead.
2. I forget Password (Reset the Router without Login)
Use a pencil to press the button for about 2-6 seconds when it is working, then leave your hands,
it will restore settings to the factory configuration. The default password is guest.
3. I have some problems related to Connection with Cable Modem
Please follow the following steps to check the problems:
Check whether the DSL modem works well or the signal is stable. Normally there will be some
indicator lights on the modem, users can check whether the signal is ok or the modem works well
from those lights. If not, please contact the ISP.
Check the front panel of the Router, there are also some indicator lights there. When the physical
connection is correct, the Power light and the CPU light should be solid; the WAN light should
be blinking. If you use your computer, the corresponding LAN port light should be blinking too.
If not, please check whether the cables work or not.
Repeat the steps in WAN Setup Connect with Internet through DSL Modem.
4. I can browse the router’s Web-based Configuration Utility but cannot access the Internet.
Check if the WAN LED is ON. If not, verify that the physical connection between the router and
the DSL/Cable modem is firmly connected. Also ensure the DSL/Cable modem is working
properly.
If WAN LED is ON, open the System Overview page of the Web configuration utility and check
the status group to see if the router‟ s WAN port has successfully obtained an IP address.
Make sure you are using the correction method (Dynamic IP Address, PPPoE, or Static IP)
as required by the ISP. Also ensure you have entered the correct settings provided by the ISP.
For cable users, if your ISP requires a registered Ethernet card MAC address, make sure you
have cloned the network adapter‟ s MAC address to the WAN port of the router. (See the MAC
Address field in WAN Setup.)
5. My wireless client cannot communicate with another Ethernet computer.
Ensure the wireless adapter functions properly. You may open the Device Manager in Windows
Wireless-N 3G Router User Manual
68 / 69
to see if the adapter is properly installed.
Make sure the wireless client uses the same SSID and security settings (if enabled) as the
150Mbps Wireless-N Broadband Router.
Ensure that the wireless adapter‟s TCP/IP settings are correct as required by your network
administrator.
If you are using a 802.11b wireless adapter, and check that the 802.11G Mode item in Wireless
Basic Setting page, is not configured to use 802.11G Performance.
Use the ping command to verify that the wireless client is able to communicate with the router‟s
LAN port and with the remote computer. If the wireless client can successfully ping the router‟ s
LAN port but fails to ping the remote computer, then verify the TCP/IP settings of the remote
computer.