NETIS SYSTEMS DL4304R ADSL2+ MODEM WITH 150MBPS WIRELESS-N ROUTER User Manual 4304d EN Modem Router QIGx

NETIS SYSTEMS CO., LTD. ADSL2+ MODEM WITH 150MBPS WIRELESS-N ROUTER 4304d EN Modem Router QIGx

USERS MANUAL

Download: NETIS SYSTEMS DL4304R ADSL2+ MODEM WITH 150MBPS WIRELESS-N ROUTER User Manual 4304d EN Modem Router QIGx
Mirror Download [FCC.gov]NETIS SYSTEMS DL4304R ADSL2+ MODEM WITH 150MBPS WIRELESS-N ROUTER User Manual 4304d EN Modem Router QIGx
Document ID1878470
Application IDHW8cuKM1tESBO7sPV/UBRQ==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize61.95kB (774410 bits)
Date Submitted2013-01-14 00:00:00
Date Available2013-01-14 00:00:00
Creation Date2013-01-08 10:09:35
Producing SoftwareAcrobat Distiller 9.5.1 (Windows)
Document Lastmod2013-01-08 15:04:34
Document TitleMicrosoft Word - 4304d EN Modem&Router QIG.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: Administrator

DL4304D
ADSL2+ Modem Plus 150Mbps
Wireless-N Router
Quick Installation Guide
1. Hardware Installation
Step 1: Connect the ADSL Line.
Method one: Plug one end of the twisted‐pair ADSL cable into
the ADSL LINE port on the rear panel of the router, and insert
the other end into the wall socket.
Method two: You can use a separate splitter. The external
splitter has three ports:
• Line: Connect to the wall jack
• Phone: Connect to the phone sets
• Modem: Connect to the ADSL LINE port of the router
Step 2: Connect the Ethernet cable. Attach one end of a network
cable to your computer's Ethernet port or a regular hub/switch port,
and the other end to the LAN port on the router.
Step 3: Power on the computers and LAN devices.
Step 4: Attach the power adapter. Connect the power adapter to the
power connector on the rear of the device and plug in the adapter to
a wall outlet or power extension.
Name
PWR
ADSL
Internet
Status
Indication
On
Power is on
Off
Power is off
Flash
The ADSL negotiation is in progress
On
The LINE port is linked up.
Off
The LINE port is linked down.
Flash
Data is being transferred over the Internet.
On
A successful PPP connection has been built.
Off
Router works on Bridge mode.
Flash
There is wireless data being transmitted.
On
The wireless function is enabled but no data is
Off
The wireless function is disabled.
Flash
Data is being transferred over the 1‐4 (LAN) port.
Figure 1
There is no successful PPP connection or the
WLAN
being transmitted.
LAN(1‐4)
There
On
is
successful
connection
on
the
corresponding 1‐4 (LAN) port but no activity.
There is no connection on the corresponding 1‐4
Off
(LAN) port or the connection is abnormal.
2. Configure PC
ForWindows 7 or Windows Vista as below.
Step 1: Click
, then select the Open Network and Sharing
Center.
Figure 4
Step 4: Double click the “Internet Protocol Version 4(TCP/IPv4)”.
Figure 2
Step 2: Click the Change adapter settings.
Figure 3
Step 3: Click Local Area Connection with the right button of your
mouse. Then select Properties.
Figure 5
Step 5: Select the “Obtain an IP address automatically” as below.
Then click “OK”.
Passwordadmin
Figure 8
And then click OK to access to the Wireless Modem Management
Panelscreen.
Figure 6
4. Modem Management
3. Login
This webpage provides you the convenient and simplest way to
configure your Modem to access the internet.
Start your web browser and type the private IP address of the
Firstly. Click and go to “Setup”‐>”WAN” , Page is showing below:
(we are taking PPPoE for example)
Router in the URL field: 192.168.1.1.
Secondly. Enter the VPI and VCI provided by your ISP and select the
Channel mode as PPPoE
Figure 7
Then,enter the default User Name admin and the default
Third: Enter the Fixed IP address which provided by your ISP then
click “ Add”
wireless network parameters required to access the AP of your WLAN
interface.
Fourth: Click “Save” botton to make it effetive.
Go to Setup->WLAN->Basic page, you can configure the wireless
parameters.
Here you may enable or disable the wireless function. You can also
change the wireless parameters, such as Band, SSID, Channel Width,
Control Sideband, Channel Number and Radio Power.
Figure 9
5. Wireless Network&Security
To connect to the Wireless AP, we should have the most basic
configuration of the router at first. In this section, you can set the
Figure 10
Step 2:Go to Setup->WLAN->Security page, you can configure the
wireless security parameters.
Here you can choose the encryption method to prevent any
unauthorized access to your wireless network.
There are three most commonly used encryption method (a total of six
encryption support), including the WEP encryption, WPA-Personal,
WPA2-Personal, etc.
Click “Apply Changes” to make it effective
Figure 12
Step 4: Click
“Wirelesss Network Connection” with the right butto
on
of your mouse.
Then seelect “View Avaailable Wirelesss Networks”.
Figure 13
Step 5: Double
click thee wireless network your product provided.
Figure 11
Step 3: Click “My Network Places” with the right button of your
mouse. Then select “Properties”.
10
11
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
Figure 14
Step 6: Input the key you stetted before if the wireless network you
connecting to requests password.
Certification
FCC CE
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolledenvironment. This transmitter must not be
co‐located or operating in conjunction with any otherantenna or
transmitter. This equipment should be installed and operated with a
minimumdistance of 20 centimeters between the radiator and your
body.
This unit complies with Part 15 & 68 of FCC Rules. Operation is
subject to following two conditions:
1) This device may not cause harmful interference
FCC Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to pro‐vide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
in‐stalled and used in accordance with the instructions, may cause
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
12
13
the equipment.
Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to
operate the equipment.
certain of the number of devices that may be connected to a line (as
determined by the total RENs) contact the local telephone company.
If this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice
isn’t practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary. The telephone
company may make changes to its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If
this happens, the telephone company will provide advance notice so
you can make the necessary modifications to maintain uninterrupted
service. For technical support, contactNetis Systems USA Corp. at
18541 Gale Avenue, City of Industry, CA 91748 or callTEL: 626‐486‐
9208. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the
equipment until the problem is resolved.
INFORMATION TO BE SUPPLIED TO USERS
We confirm that the following information will supplied to the users
of this equipment. This information will be provided with the user’s
manual.
FCC REQUIREMENTS
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the exterior of the cabinet of
this equipment is a label that contains, among other information, the
FCC Registration Number and Ringer Equivalence Number (REN) for
this equipment. A product identifier in the format US:
SX5DL01BDL4304R. If requested, this number must be provided to
the telephone company.
FCC compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the
telephone network or premises wiring using a compatible modular
jack that is Part 68 compliant. See Installation Instructions for details.
The REN is used to determine the quantity of devices that may be
connected to the telephone line. Excessive RENs on the telephone
line may result in the devices not ringing in response to an incoming
call. Typically, the sum of RENs should not exceed five (5.0). To be
14
2)
This device must accept any interference received, including.
Interference that may cause undesired operation.
15

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : 3.1-701
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:01:08 15:04:34+08:00
Create Date                     : 2013:01:08 10:09:35+08:00
Metadata Date                   : 2013:01:08 15:04:34+08:00
Format                          : application/pdf
Title                           : Microsoft Word - 4304d EN Modem&Router QIG.docx
Creator                         : Administrator
Producer                        : Acrobat Distiller 9.5.1 (Windows)
Document ID                     : uuid:2ae55465-1a07-4b97-929c-d3b897ab994c
Instance ID                     : uuid:bf449072-506e-463e-ae04-651aca8d96e1
Page Count                      : 4
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: T58DL4304R

Navigation menu