NETIS SYSTEMS E1PR 300Mbps Wireless N Range Extender User Manual PKUM05672 E1 QIG r1
NETIS SYSTEMS CO., LTD. 300Mbps Wireless N Range Extender PKUM05672 E1 QIG r1
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2523767 |
| Application ID | BlUJzWV4O7MhMKfXA0jMIg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 37.23kB (465406 bits) |
| Date Submitted | 2015-02-04 00:00:00 |
| Date Available | 2015-02-04 00:00:00 |
| Creation Date | 2015-01-23 18:36:10 |
| Producing Software | Adobe PDF library 10.01 |
| Document Lastmod | 2015-01-23 18:36:10 |
| Document Title | PKUM05672 E1+ -QIG_r1 |
| Document Creator | Adobe Illustrator CS6 (Windows) |
| Document Author: | Administrator |
netis Wireless N Range Extender Quick Installation Guide netis Wireless N Range Extender Quick Installation Guide 3. Typical Applications and Installation 1.Package Contents Please check the correct application according to your network environment, and follow the corresponding steps for the selected application. Application 1: Range Extender (Default mode) netis WirelessN Range Extender Quick InstallationGuide WPS Ethernet Cable E1+ netis Wireless N Range Extender Quick Installation Guide The E1+ can be used to repeat signal from the existing wireless network. It is suitable to extend wireless coverage for the places where the existing wireless network signal is too weak to maintain a stable wireless connection. Quick Installation Guide netis Wireless N Range Extender Quick Installation Guide netis Wireless N Range Extender Quick Installation Guide Method B: Range Extender setup via Web Management Page Step 1. Press the WPS Button on your main router. Installation for Application 1: Range Extender Mode You can setup E1+ in two ways: pressing WPS Button or via Web Management Page. Model No.:E1+ Firmware Version:V1.2.31730 WPS Step 2. Press WPS Button on E1+ for 1～2 seconds. LAN/WAN Port WIFI403 WIFI-410 WIFI-407 Connect (Take Windows 8 as an example) WPS Quick Installation Guide Tablet Smartphone 2.1 LED Range Extender mode Solid Blue Solid Orange WPS Travel Router mode The connection between E1+ and main router is stable. Normal signal The connection between E1+ and main router is unstable. Please check the main router status and put E1+ closer to it. Enhanced signal Flashing Blue/Orange E1+ is not connected to the front device (Main router, xDSL/Cable /Fiber modem). Purple The device is initializing. Laptop Application 2: Travel Router The E1+ can be used to receive Internet access from an Internet Service Provider (ISP) and share that access with local devices wirelessly. WPS Button Description Range Extender mode Model No. E1+ Quick extender setup: Press button for 1~2 seconds to activate the WPS function. Connect to a wired device like desktop, set-top box, printer, for network sharing. Signal strength switch: Press the button for 1~2 seconds, the signal strength can be switched between normal signal and enhanced signal. Note: Please place the E1+ closely to your main router when you setup extender. Also after you are successfully connected, you can move your E1+ to other areas. Note: If the login page cannot pop up, please check your computer is set to obtain IP address automatically. Step 3. You are successfully connected! Smartphone E1+ Laptop E1+ netis Wireless N Range Extender Quick Installation Guide Step 3. Click on the “Travel Router” icon in the upper-right corner. E1+ netis Wireless N Range Extender Quick Installation Guide Tr av el Router netis Wireless N Range Extender Quick Installation Guide Step1 W ireless Optim izat ion Successfully Connected! Checking Your Wi-Fi Environment... netis Wireless N Range Extender Quick Installation Guide How do I restore my Extender configuration to its default settings? Method 1. With E1+ powered on, press and hold the WPS button for 5 seconds until the LED is flashing. Method 2. In the main page of web management page, click “Advanced” “Factory Default” to reset E1+ to factory default. >New Password: Password Model No.:E1+ Firmware Version:V1.2.31730 Range Extender mode Http:// www.netis-systems.com E-mail: support@netis-systems.com Start Model No.:E1+ Firmware Version:V1.2.31730 Select the Wireless Network to Extend netis vpn On Roaming: Wi-Fi: Password: Off netis-1 Step1 W ireless Optim izat ion V1.2.31730 Hotel netis password US Auto Sav e Automatically set the best Channel! Tr av el Router Automatically set the best Radio Band! Http:// www.netis-systems.com E-mail: support@netis-systems.com Automatically set enhanced Signal Strength! Starting to detect your Internet Connection Type... A dvanced Travel Router mode Start Step 5. Select “Start Now”. Note: In default, the Auto-Config system can help you to finish the configuration automatically. If you want to set E1+ manually, please select “Manually Set”. Other people might be able to see info you send over this network In default, the Auto-Config system will set E1+ to work under enhanced signal mode automatically. There're two methods to change it. Method 1. With E1+ powered on, press the WPS button for 1~2 seconds, the signal strength can be switched between normal signal and enhanced signal. (Blue for normal signal, Orange for enhanced signal.) Method 2. In the main page of web management page, set “Manually Set” to change the signal strength. Step 6. Wait for 1 minute until the configuration is saved and takes effect. Http:// www.netis-systems.com E-mail: support@netis-systems.com (Take Windows 8 as an example) Step 2. Open your browser and type “http://netisext.cc” in the address field to visit E1+'s web management page. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The netis Auto-Config system is going to start... 4 Model No.:E1+ Firmware Version:V1.2.31730 H om e Network Configuration Succeeded Your have successfully configured network! Normal Enhanced Wi-Fi Name: netis password: password OK Save Technical Support: USA/ Canada Toll Free: +1 866 71 network (+1 866 716 3896) E-mail: usa_support@netis-systems.com Http:// www.netis-systems.com E-mail: support@netis-systems.com H om e Step2 Internet Connection Auto-Detect Your Internet Connection Type is: DHCP DHCP Static IP PPPoE Other Regions: E-mail: support@netis-systems.com Tip : Default Login Address: http://netisext.cc Default SSID: netis NETIS SYSTEMS CO., LTD. www.netis-systems.com MADE IN CHINA Manually Set Start Now Next Http:// www.netis-systems.com E-mail: support@netis-systems.com Http:// www.netis-systems.com E-mail: support@netis-systems.com 10 11 12 PKUM05672 Note: If the login page cannot pop up, please check your computer is set to obtain IP address automatically. H om e Your netis router has not been configured yet. 2) Internet Connection The system will automatically detect your Internet Connection Type then please manually fill in the needed network parameters from your ISP (Internet Service Provider). If the Internet Connection Type isn't detected successfully or shows wrong, please manually select the type and fill in the needed network parameters from your ISP. Model No.:E1+ Firmware Version:V1.2.31730 Model No.:E1+ Firmware Version:V1.2.31730 http://netisext.cc What can I do if I failed to extend the wireless range by “WPS Button”? Appendix: FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. W ireless S ignal Networks Airplane mode Off WIFI-409 WIFI-411 WIFI-410 WIFI-407 netis Connect OK Wi-Fi Name: Password: Region: Channel: Step 4. Click on “Start” button. 3.2.2 Configuration Step 1. Search and connect to the E1+ network “netis” with your computer or mobile terminal device. Connect automatically Password Cancel Roaming Your may set your own Wi-Fi Name and Password. Model No.:E1+ Firmware Version:V1.2.31730 E1+ H om e Step3 Wi-Fi Setings E1+ 1) Connect the LAN/WAN port of E1+ to an xDSL/Cable/Fiber modem or uplink Ethernet port with an Ethernet cable. 2) Plug E1+ to a standard electrical socket. 4.Troubleshooting 3) Wi-Fi Settings Please input your Wi-Fi Name and Password, then click “Save”. A dvanced WPS Cannect Start Note: The E1+ supports the following three Internet Connection Types. DHCP: The E1+ will automatically receive the IP parameters from your ISP. Static IP: Please enter the IP Address/Subnet Mask/Default Gateway/DNS Servers given by your ISP. PPPoE: Please enter the Username and Password given by your ISP. 1) Wireless Optimization Note: The system will automatically finish this step. V1.2.31730 >New Wi-Fi: netis vpn Cancel Range Extender mode Model No.:E1+ Firmware Version:V1.2.31730 Note: In default, E1+ works under Roaming mode, so the extended Wi-Fi will use the same network name and password as your main router. If you want to set different network name and password, please click on “Roaming” to turn off the Roaming mode. And then you can set the customized name and password for the extended Wi-Fi. Wireless Network: netis vpn Tr av el Router Password Modem >To reconfigure the Extender, please login with:http://netisext.cc V1.2.31730 WPS Laptop netis Wireless N Range Extender Quick Installation Guide Installation for Application 2: Travel Router Mode 3.2.1 Hardware Connection Step 5. Type in wireless password of the main router and click “Connect” to setup your Wi-Fi Extender network. Step 3. Click on “Start” button Note: Once the setting is finished, the extended Wi-Fi will use the same network name and password as your main router, then the wireless devices can be connected to the Internet. Also, you can connect a wired device like desktop, set-top box, printer to E1+ with an Ethernet cable for network sharing. WPS WPS Button Http:// www.netis-systems.com E-mail: support@netis-systems.com A dvanced Connect to an xDSL/Cable/ Fiber modem or uplink Ethernet port for Internet Access. Note: Different power plug is provided for different region. Here we just take US version for example. netis Wireless N Range Extender Quick Installation Guide Step 6. You are successfully connected! 1) Please make sure that your main router can connect to the Internet successfully. 2) Plug E1+ to a standard electrical socket. Method A: Range Extender setup via WPS Button (Particularly recommended) Note: Please make sure that the main router is with WPS Button, and the function is enabled. If you cannot find WPS function, please turn to “Method B: Extender setup via Web Management Page”. Modem Travel Router mode Factory default setting: Press and hold the WPS button for about 5 seconds until the LED is flashing. LAN/WAN Port http://netisext.cc 3.1.2 Configuration 2.2 Button and Port Item WPS WPS E1+ Desktop Manually Set Step 2. Open your browser and type “http://netisext.cc” in the address field to visit E1+'s web management page. E1+ Indication LED Status netis Connect automatically Button netis Wireless N Range Extender Roaming netis vpn Other people might be able to see info you send over this network Main Router WPS Select the Wireless Network to Extend Networks Airplane mode Off WIFI-409 WIFI-411 WIFI-410 WIFI-407 netis Main Router LED Step 4. Select your network of the main router (For example: netis vpn). Step 1. Search and connect to the E1+ network “netis” with your computer or mobile terminal device. 3.1.1 Hardware Connection 2.Hardware Information netis Wireless N Range Extender Quick Installation Guide
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2015:01:23 18:36:10+09:00 Creator Tool : Adobe Illustrator CS6 (Windows) Modify Date : 2015:01:23 18:36:10+08:00 Metadata Date : 2015:01:23 18:36:10+08:00 Thumbnail Width : 256 Thumbnail Height : 156 Thumbnail Format : JPEG Thumbnail Image : (Binary data 11445 bytes, use -b option to extract) Producer : Adobe PDF library 10.01 Format : application/pdf Creator : Administrator Title : PKUM05672 E1+ -QIG_r1 N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 549.999848 Max Page Size H : 330.000012 Max Page Size Unit : Millimeters Font Name : ArialMT, Arial-BoldMT, Verdana, Verdana-Bold, SimSun, MicrosoftYaHei, RTWSYueRoudGoDemo-Regular Font Family : Arial, Arial, Verdana, Verdana, 宋体, 微软雅黑, RTWSYueRoudGoDemo Regular Font Face : Regular, Bold, Regular, Bold, Regular, Regular, Regular Font Type : Open Type, Open Type, Open Type, Open Type, TrueType, Open Type, Unknown Font Version : Version 5.06, Version 5.06, Version 5.03, Version 5.03, Version 5.03, Version 6.02, Version 5.016;PS 5.006;hotconv 1.0.67;makeotf.lib2.5.33168 Font Composite : False, False, False, False, False, False, False Font File Name : arial.ttf, arialbd.ttf, verdana.ttf, verdanab.ttf, simsun.ttc, msyh.ttf, AdobeHeitiStd-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Document ID : xmp.did:F4933239EBA2E4119B7BED99E5207F3B Instance ID : uuid:5c8c833c-661d-4708-bd9b-1b85842d1d93 Original Document ID : xmp.did:F3933239EBA2E4119B7BED99E5207F3B Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:F3933239EBA2E4119B7BED99E5207F3B Derived From Document ID : xmp.did:F3933239EBA2E4119B7BED99E5207F3B Derived From Original Document ID: xmp.did:F3933239EBA2E4119B7BED99E5207F3B Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:F3933239EBA2E4119B7BED99E5207F3B, xmp.iid:F4933239EBA2E4119B7BED99E5207F3B History When : 2015:01:23 18:33:08+08:00, 2015:01:23 18:35:58+08:00 History Software Agent : Adobe Illustrator CS6 (Windows), Adobe Illustrator CS6 (Windows) History Changed : /, / Page Count : 1 Author : AdministratorEXIF Metadata provided by EXIF.tools