NETIS SYSTEMS WF2301RT 150Mbps Wireless-N Outdoor Access Point User Manual netis WF 2301

Download:
Mirror Download [FCC.gov]
Document ID	1709509
Application ID	uOrDMxCBDUEXm9tjbBZ94A==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	84.44kB (1055461 bits)
Date Submitted	2012-05-30 00:00:00
Date Available	2012-05-30 00:00:00
Creation Date	2012-04-13 14:27:42
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2012-04-13 14:32:29
Document Title	Microsoft Word - netis WF-2301.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	user

netis 150Mbps Wireless-N
Outdoor Access Point
Quick Installation Guide
WF-2301
V1.1.01
2012-02-08
Package Contents
The following items should be found in your package

150Mbps Wireless-N Outdoor AP

PoE Adapter

Quick Installation Guide
Please make sure that the package contains the above items, if any of the listed items are damaged
or missing, please contact with your distributor.
Before You Begin
Minimum Requirements:

Broadband Internet access service (DSL / Cable / Ethernet)

Internet Explorer 5.0 or higher for Web configuration

802.11n，802.11g or 802.11b compliant wireless adapters (for wireless connection)

Windows 98/2000/XP/2003/Vista or higher operating system
1. Hardware Installation Procedures
The procedures to install the Wireless-N AP please refer to Figure 1-1
Figure 1-1

Step 1 connecting Cable/ADSL Modem to the WAN port.
Attach one end of an Ethernet cable to your modem’s Ethernet port, and the other end to one
of the WAN ports of your router.



Step 2 connecting the power adapter.
Attach one end of an Ethernet cable to the Internet access router LAN port, the other end to
the Internet port of power adapter. Then plug the Power Adapter into an AC outlet.
Step 3 connecting the 150Mpbs outdoor adapter.
Connect another Ethernet cable from your POE port of the power adapter to the LAN port of
150Mbps outdoor AP.
Step 4 Power on the following devices in this order:
Cable/ADSL modem, Router.
2. LED Indicators
Figure 2-1
LED
Function
ON
Power on
Off
Power off
On
Connection normal
Off
Abnormal
Flashing
POE
Data transmitting
On
Power supply normal
Off
Abnormal
Flashing
Off
4 light signal strength above 75%
3 light signal strength medium
Less than 2 light signal strength is
weak.
No signal
3. Configure computer
3.1. Windows 98/Me
1. Go to Start  Settings  Control Panel.
2. Find and double-click the Network icon. The Network dialog box appears.
3. Click the Configuration label and ensure that you have network card.
4. Select TCP/IP. If TCP/IP appears more than once, please select the item that has an arrow “”
pointing to the network card installed on your computer. DO NOT choose the instance of TCP/IP
with the words “Dial Up Adapter” beside it.
5. Click Properties. The TCP/IP Properties dialog box appears.
6. Ensure the Obtain IP Address Automatically is checked.
7. From the WINS Configuration dialog box, Ensure that Disable WINS Resolution is checked.
8. From the Gateway dialog box, remove all entries from the Installed gateways by selecting them
and clicking Remove.
9. From the DNS Configuration dialog box, remove all entries from the DNS Server Search Order
box by selecting them and clicking Remove. Remove all entries from the Domain Suffix Search
Order box by selecting them and clicking Remove. Click Disable DNS.
10. Click OK, back to Network Configuration dialog box
11. Click OK, if prompted to restart, click YES.
3.2. Windows 2000
Please follow the steps below to setup your computer:
1. Go to Start  Settings  Control Panel
Figure 3-1
2. Double click the icon Network and Dial-up Connections
3. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Figure 3-2
4. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-3
5. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and
then press OK to close the Internet Protocol (TCP/IP) Properties window
Figure 3-4
6. Press OK to close the Local Area Connection Properties window
Figure 3-5
3.3. Windows XP
Please follow the steps below to setup your computer:
1. Go to Start  Settings  Control Panel
2. Click Network and Internet Connections
Figure 3-6
3. Click Network Connections
Figure 3-7
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Figure 3-8
5. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-9
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and
then press OK to close the Internet Protocol (TCP/IP) Properties window
Figure 3-10
7. Press OK to close the Local Area Connection Properties window
Figure 3-11
3.4. Windows Vista
Please follow the steps below to setup your computer:
1. Go to Start  Settings  Control Panel
2. Click Network and Sharing Center
Figure 3-12
3. Click Manage Network Connections
Figure 3-13
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Figure 3-14
5. Highlight Internet Protocol Version 4 (TCP/IP) and then press Properties button
Figure 3-15
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically, and
then press OK to close the Internet Protocol (TCP/IP) Properties window
Figure 3-16
7. Press OK to close the Local Area Connection Properties window.
Figure 3-17
3.5. Windows 7
Please follow the steps blow to setup your computer:
1.
Go to Start→ Control Panel→ Network and Internet.
2.
Click Network and Sharing Center→ Change adapter settings.
3.
Highlight the icon Local Area Connection, right click your mouse, and click Properties.
Highlight Internet Protocol version 4 (TCP/IPv4).
Figure 3-18
Figure 3-19
4.
Choose Obtain an IP address automatically and Obtain DNS server address automatically,
and then press the OK to close the window.
Figure 3-20
5.
4.
Press OK to close the Local Area Connection Properties window.
Checking Connection with the Adapter
After configuring the TCP/IP protocol, use the ping command to verify if the computer can
communicate with the Router. To execute the ping command, open the DOS window and Ping the
IP address of the 300Mbps Wireless-N Gigabit Router at the DOS prompt:

For Windows 98/Me: Start → Run. Type command and click OK.

For Windows 2000/XP: Start → Run. Type cmd and click OK.

For Windows Vista/7:Start→ Type cmd at the start search bar and press the Enter.
If the Command window returns something similar to the following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Then the connection between the router and your computer has been successfully established.
If the computer fails to connect to the router, the Command window will return the
following:
C:\Documents and Settings\admin>ping 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Verify your computer's network settings are correct and check the cable connection between
the router and the computer.
In order to make the whole network operate successfully, it is necessary to configure the
150Mbps AP through your computer has a WEB browser installed. Please follow up the steps
listed below.
5. Login
Open a web browser (Safari, Internet Explorer, etc.) on the computer you have just connected to
the router, type http://192.168.1.1 in the address bar, and press enter
Figure 5-1
In the pop-up window, enter the user name guest and password guest and then click OK
Figure 5-2
6. Wireless AP Setup
6.1. Password Setup
The default username/password is guest/guest. To ensure the Router’s security, it is suggested that
you change the default password to one of your choice, here enter a new password and then
Re-enter it again to confirm your new password. Click “Save” button to save settings.
Figure 6-1
6.2. Upgrade
Click "Browse..."button and select a File to upgrade, after you have selected the appropriate file,
click "Upgrade" button to execute upgrade procedure. Do not cut off the power supply during the
process of upgrading.
Figure 6-2
6.3. Factory Defaults
Click "Restore" button, the Router will erase all of your settings and replace them with the factory
defaults, make sure you have backup current settings before click this button.
Figure 6-3
6.4. Wireless Security Settings
The item allows you to encrypt your wireless communication, and you can also protect your
wireless network from unauthorized user access. It supplies “WEP”, “WPA-PSK”, “WPA2-PSK”
and “WPA/WPA2-PSK” five different encryption modes.
6.4.1. WEP



Figure 6-4
Key Length: There are two basic levels of WEP encryption, 64 bits and 128 bits, the more
bits password have, the better security wireless network is, at the same time the speed of
wireless is more slower.
Key Mode: If you select WEP to encrypt your data, choose the bits of password, it should be
64 bits or 128 bits. Then choose the format of password; it should be HEX or ASCII. The
valid character for HEX format should be numbers from 0 to 9 and letters from A to F. HEX
support mixed letter and number mode. And ASCII supports all characters that in keyboard.
Key Length description: when you select 64bits, you need to input 10 chars for HEX and 5
chars for ASCII, and when you select 128bits, you need to input 26 chars for HEX and 13
chars for ASCII.
Note: when the WPS is enabled, please not use WEP.
6.4.2. WPA-PSK
Figure 6-5



Encryption type: You can select the algorithm you want to use, TKIP, AES or TKIP&AES.
TKIP means “Temporal Key Integrity Protocol”, which incorporates Message Integrity Code
(MIC) to provide protection against hackers. AES, means “Advanced Encryption System”,
which utilizes a symmetric 128-Bit block data.
Key Renewal: you can configure the renewal time between 60 to 86400 seconds.
Key Length description: you need to input 8 to 63 ASCII characters no matter which type you
select.
6.4.3. WPA2-PSK
The WPA2-PSK is similar to WPA-PSK and with stronger encryption method than WPA-PSK,
using WPA2-PSK; you should input password (leave this value in the range of 8 to 63 characters)
and key renewal time (leave this value in the range of 60 to 86400 seconds).
Figure 6-6
6.4.4. WPA/WPA2-PSK
This item mixed WPA-PSK and WPA2-PSK mode, which provides higher security level; you can
configure it according with WPA-PSK or WPA2-PSK.
Figure 6-7
6.5. WDS Settings
If you have selected WDS or AP+WDS mode in Wireless Basic-Radio Mode, please do the
following configurations.
Figure 6-8

WDS Name: Give a description of your wireless bridge to tell apart.

WDS MAC Address: If the current working mode is “WDS” or “AP+WDS”, then you need
to configure wireless bridge configuration. Enter MAC address of remote access point, at the
same time the remote access point also need to configure to “WDS” or ”AP+WDS” mode.

Current WDS Information: It illustrates basic information of all wireless bridge that in
connection status, you may delete unnecessary bridge.
AP1:

Select radio mode is WDS or AP+WDS

Click on ‘Wireless Management’- ‘AP Setup’- ‘Security’ and select and save None as
in wireless management-basic of AP1.
authentication type.

Click on ‘Wireless Management’- ‘AP Setup’- ‘Security’ and select and save None as WDS
authentication type or select a WDS security type, enter key and save.

Input WDS name (e.g.: default), input MAC address of AP2 (00-22-4f-bc-af-5d), click add,
then the record named default will appears in WDS list.

Select Channel is ‘Channel 6’in wireless management-basic of AP2.
AP2:

Select radio mode is WDS or AP+WDS


The IP address of AP2 should be 192.168.1.x (1
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : user
Create Date                     : 2012:04:13 14:27:42+08:00
Modify Date                     : 2012:04:13 14:32:29+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Title                           : Microsoft Word - netis WF-2301.doc
Creator                         : user
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2012:04:13 14:32:29+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:5739180b-2fcd-4563-9fc3-2665a441738b
Instance ID                     : uuid:db869f6c-402d-4fdf-a5b0-706360bbd5fe
Page Count                      : 22

EXIF Metadata provided by EXIF.tools