NETIS SYSTEMS WF2471B Wireless Dual Band Router User Manual

NETIS SYSTEMS CO., LTD. Wireless Dual Band Router

user manual

Package Contents
System Requirement
Windows 8 Windows 7 Windows Vista
Windows XP Windows 2000
1. Connect the WAN port on your router to the Modem's LAN port with an Ethernet cable
2. Connect your computer to any LAN port on netis router with an Ethernet cable
3. Plug in the power adapter of netis router
4. Unplug your ADSL or Cable Modem power at least 15 seconds and plug it back in
1.Hardware Connection
2.
POWER
CABLE
LINE IN
CABLE
POWE R
Modem
*This QIG is shared by netis wireless dual band router
Set the IP address of your wired network adapter as
Automatically as showing below
1
(Turn over)
WF2471
Wireless Dual Band Router
Quick Installation Guide
Connecting by netis one stop setup
1
Connection
IPV4 Connectivity:
IPV6 Connectivity:
Media State:
Duration:
Speed:
Internet
No Internet access
Enabled
00:39:39
100.0Mbps
Details. ..
Activity
Sent Received
10,000,680 80,000,680
Status
General
Byes:
Disable Diagnose
Close
3
2
QIG
Power Adapter
Wireless dual band router
N60 0 Wirel ess
Dua l Band( Gigab it) Rou ter
Qui ck Inst allat ion Gui de
Ethernet Cable
6
Open your browser and type 192.168.1.1
in the address field
2
3
http://192.168.1.1
4
5
tip.Most internet connectio type is DHCP as l ong a s
you don`t have ID/Password for connection Internet.
One stop setup!
The most convenient nets`AP Router configuration!
Internet Connection Type
Wiress Setup
SSID:
Password:
2.4GHz
5GHz
Pass word
tip. pl eas e en ter any 8 -63 cha rc ters
Advanced
Internet
Wiress
Save
Tips 1: If you are connecting to a Broadband service
that uses a dynamic connection (DHCP), you may
be online already. Try opening a web browser and
enter a web site. If you connect to a web site, you
are fnished with your Internet setup.
Select the Internet Connection Type you
use. We take DHCP for example. Configure
your Wireless Setup such as SSID Password
then click save to make setting effective. The
connection status page will appear below
connection sucessfully. you had been online!
Tips 2: you would click
to go to advance setting page.
Advanced
R
pass word
netis_2_4G
5G
DHCP(Cable Mode m) Static IP PPPoE
Enable Disable
3.Troubleshooting
PKUM01227
How do I restore my Router's con guration to its factory default settings?
With the Router powered on, press and hold the Default button on the rear panel for 8 to 10
seconds using a pin before releasing it.
Q
A
What can I do if I cannot access the Internet?
1) Check to see if all the connectors are connected well, including the telephone line (for your
modem), Ethernet cables and power adapter.
2) Check to see if you can access the Router's web manage- ment page. If you can, please follow
the following steps to solve the problem. If you can't, please refer to Appendix 1.
3) Make sure that you are connected to the netis Router with the computer that was originally
connected to your modem, then log on to the web-based management page and browse to
'Network > MAC Clone', click'Clone MAC Address' and then click 'Save'. Reboot the Router
MAC Clone
Do not set the same MAC address as the wirless network ca rd at t he WI SP mo de.
WAN MAC Address:78:2b:cb:ea:9c"2b Restore Factory MA C Clo ne MA C add res s
Save
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement This device complies with FCC radiation
exposure limits set forth for an uncontrolled environment and it also
complies with Part 15 of the FCC RF Rules. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.
This equipment complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
Operations in 5150~5250MHz band is for indoor use only..

Navigation menu