NIDEC MOBILITY GHW-M002 EV Remote Stick User Manual EV Remote Operation manual ai
OMRON Automotive Electronics Co. Ltd. EV Remote Stick EV Remote Operation manual ai
Users Manual
EV_REMOTE operation manual
Antenna module
3
4
Regulatory compliance
Configuration
Part names
Stick
LCD
Power / Link button
Mode setting button
Manual
charge button
Setting button (UP)
Product label
Battery cover
Product label
CN2 connector
CN1 connector (antenna connection)
Battery replacement
Batteries: CR2032 x 2
We recommend that you replace the batteries after one year's use as a guide.
How to replace the batteries
1. Remove the battery cover
Slide the slide part of the battery cover in
the direction of and lift the cover in the
direction of to release the hooks of the
battery cover ( ).
Battery cover
Slide part
lithium batteries
(CR2032)
Insert the new batteries (CR2032) with the
positive ( + ) side facing up.
2. Replace the batteries
3. Place the battery cover
After inserting the hooks of the battery
cover ( ), lower the cover into position
( ) and slide the slide part in the direction
of .
Main specifications
After sales service
How to use
For after sales service, contact :
OMRON Automotive Electronics Co. Ltd.
6368 nenjyozaka, okusa
Komaki, Aichi 485-0802 JAPAN
Tel: +81 568 78 6392
URL: http://www.oae.omron.co.jp
Stick
Antenna module
Transmission frequency 926.85 MHz band (FCC/IC), 869.85 MHz band (EU)
Transmission power < 50 mV/m (FCC/IC), < 5mW e.r.p (EU)
Antenna 1/4 lambda rod antenna
Switches Power on/off, Mode, Charge, Setting
Battery Lithium battery (CR2032 x 2)
Dimensions 88.4 mm x 32 mm x 18 mm ( not including protrusion)
Weight 35 g
Link state acknowledgment Buzzer / LCD
Transmission frequency 926.85 MHz band (FCC/IC), 869.85 MHz band (EU)
Transmission power < 50 mV/m (FCC/IC), < 5mW e.r.p (EU)
Power supply 5 V
Current consumption 1.5 mA (for receiving)
Antenna 1/4 lambda printed antenna
Operation temperature range -10 C to +70 C
Operation temperature range -30 C to +85 C
Dimensions 52 mm x 25 mm x 52 mm
Weight 35 g
Turning the power of the stick on
Setting the charge time
Setting the air conditioner
Turning the power of the stick off
Pressing the Power/Link button for more than 1 second turns the power of the stick
on (with a buzzer sound) and the stick starts transmitting a request signal to obtain
vehicle information. If a response signal from the vehicle is properly received, the
vehicle information will be displayed on the LCD with a buzzer sound.
The time till charging is started (charge wait time) and the charging time can be set
with the stick.
Caution When pulling the antenan out or putting it back, move it straight up/down with
holding the top of the antenna. The antenna may be damaged if being pulled
with brute force or bended.
Pressing the mode setting button once while the vehicle informaiotn is displayed on
the LCD enables the charge wait time setting mode. In the charge wait time setting
mode, the charge wait time can be set with the setting button.
After setting the wait time, the setting information will be sent to the vehicle by
pressing the Power/Link button. If a response signal from the vehicle is properly
received, the setting information will be displayed on the LCD with a buzzer
sound.
By pressing the mode setting button once during the charge wait time setting mode,
the stick is set to the charge time setting mode. Set the charge time in the same way
as done for setting the charge wait time.
Pressing the manual charge button resets the timer setting.
The car air conditioner can be controlled with the stick prior to getting into a car.
Pressing the mode setting button once in the charge time setting mode enables the
air conditioner setting mode.
Select the temperature you want with the setting button and press the Power/Link
button to send the setting information to the vehicle.
If a response signal from the vehicle is properly received, the setting information will be
displayed on the LCD with a buzzer sound.
Pressing the Power/Link button for more than 3 seconds while the power is on turns
the power of the stick off. Also no button operation for more than 30 seconds
automatically turn the power off.
Setting button (DOWN)
FCC/IC WARNING
Any changes or modifications not expressly approved by the party responsible for product
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of this device.
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
The following standards were applied: (R&TTE Directive 1999/5/EEC)
EN 60950-1: 2006 + A11:2009
EN 300 220-2 V.2.3.1
EN 301 489-3 V.1.4.1
EN 62311:2008
Hereby, OMRON Automotive Electronics Co. Ltd., declares that Stick / Antenna module are
in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
50 g