NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC1522 Emitter User Manual eDC1600DC1602 A 00

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Emitter eDC1600DC1602 A 00

User Manual

Settingis okStop×1OK(P1+button+P1-button)×1P1+button+P1-button,hold onOrThe screen will display oThe screen will display 15The screen will display CPress P1+button or P1-button, selecting the channel (channl1 to channel 15) you needAAdditionalfunctionDC1522 valid channels selectionIn the setting state,press the up or down button you can quit quickly, if you want to change the valid channels ,reset it.DC1522 fifteen channels double control emitter: each channel had the same function with DC1520. One number of LCD screen means one control channel. Press “channel choose” button P1- (number descending) or P1+ (number increasing) to change the channel. On the analogy of this, loose finger when the indicator light move to suitable channel that you select effective channel. If LCD screen number show “0” that means the group control status. Under the status of group control, pressing a way button will start the group-control function of a way, a way of all the channels will be availabe.Pressing b way buttons will start the group-control function of b way, b way of all the channels will be availabe. p1- p1+DC1520/DC1522EmitterSpecificationType specificationTechnical supportTTDC1520 DC1522 Back sideDC1520Single - channel emitterDC152215 - channel emitterUp buttonStop buttonDown buttonUp buttonStop buttonDown buttonVersion NO. : A/00Fucntion instructionTechnical specificationInput voltage碋3VTransmitting frequency碋433MHzTransmitting power碋10 milliwattOperating temperature碋-100C—500CTransmssion distance碋200 meters open office硽 35 meters on two wallsDuring the settings,the time between two operation must be shorter than4s,otherwise it will quit the settingAAdditionalfunctionAAdditionalfunctionMatchable R tubular motor setting upAAdditionalfunctionMatchable DC1680 setting upMatchable DC136 setting upPower onSound from motorhear long soundPower onPower onPress (up+down)×1 at the same timeIndicatorflashingIndicator long flashingIndicator flashing then extinguishedSettingis okSettingis okDuring the settings,the time between two operation must be shorter than6s,otherwise it will quit the settingDuring the settings,the time between two operation must be shorter than10s,otherwise it will quit the settingUp×1Down×1OKOKDelete all the datas of the motor andthe new emitter has been programmed.Beep once Beep onceSet up is ok.The up button controlthe motor clockwiseSet up is ok.The down button controlthe motor clockwiseSetting button×1OKDC136 DC136 DC136 DC136 DC136Stop×1OKDC1680 DC1680 DC1680 DC1680 DC1680IndicatorflashingIndicator long flashingIndicator flashing then extinguishedStop×1Up×1Run or beepfor hintRun or beepfor hintUp×1P2×1P2×1CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACEDBY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDINGTO THE INSTRUCTIONSNotice: transmitter do not exposed to moisture and strike, so as not toaffect life.When you use transmitter, if found emission distance obviouslyshort or less sensitive, please change another same new battery. Please have batteries for recycling.Setting buttonSetting button
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ǂ Reorient or relocate the receiving antenna. ǂ Increase the separation between the equipment and receiver. ǂ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ǂ Consult the dealer or an experienced radio/TV technician for help.

Navigation menu