NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC1522 Emitter User Manual eDC1600DC1602 A 00
NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Emitter eDC1600DC1602 A 00
User Manual
Setting
is ok
Stop×1
OK
(P1+button+
P1-button)×1
P1+button+P1-
button,hold on
Or
The screen
will display o
The screen
will display 15
The screen
will display C
Press P1+button or P1-button,
selecting the channel (channl
1 to channel 15) you need
A
Additional
function
DC1522 valid channels selection
In the setting state,press the up or down
button you can quit quickly, if you want
to change the valid channels ,reset it.
DC1522 fifteen channels double control emitter: each channel had the same
function with DC1520. One number of LCD screen means one control channel.
Press “channel choose” button P1- (number descending) or P1+ (number
increasing) to change the channel. On the analogy of this, loose finger when
the indicator light move to suitable channel that you select effective channel.
If LCD screen number show “0” that means the group control status. Under
the status of group control, pressing a way button will start the
group-control function of a way, a way of all the channels will be
availabe.Pressing b way buttons will start the group-control function of b
way, b way of all the channels will be availabe.
p1- p1+
DC1520/DC1522
EmitterSpecification
Type specification
Technical support
T
T
DC1520 DC1522
Back side
DC1520
Single - channel emitter
DC1522
15 - channel emitter
Up button
Stop button
Down button
Up button
Stop button
Down button
Version NO. : A/00
Fucntion instructionTechnical specification
Input voltage碋3V
Transmitting frequency碋433MHz
Transmitting power碋10 milliwatt
Operating temperature碋-100C—500C
Transmssion distance碋200 meters open office硽
35 meters on two walls
During the settings,the time between
two operation must be shorter than
4s,otherwise it will quit the setting
A
Additional
function
A
Additional
function
Matchable R tubular motor setting up
A
Additional
function
Matchable DC1680 setting up
Matchable DC136 setting up
Power on
Sound from motor
hear long sound
Power on
Power on
Press (up+down)×1
at the same time
Indicator
flashing
Indicator long
flashing
Indicator flashing
then extinguished
Setting
is ok
Setting
is ok
During the settings,the time between
two operation must be shorter than
6s,otherwise it will quit the setting
During the settings,the time between
two operation must be shorter than
10s,otherwise it will quit the setting
Up×1
Down×1
OK
OK
Delete all the datas of the motor and
the new emitter has been programmed.
Beep once Beep once
Set up is ok.
The up button control
the motor clockwise
Set up is ok.
The down button control
the motor clockwise
Setting button×1
OK
DC136 DC136 DC136 DC136 DC136
Stop×1
OK
DC1680 DC1680 DC1680 DC1680 DC1680
Indicator
flashing
Indicator long
flashing
Indicator flashing
then extinguished
Stop×1Up×1
Run or beep
for hint
Run or beep
for hint
Up×1
P2×1P2×1
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
Notice: transmitter do not exposed to moisture and strike, so as not to
affect life.When you use transmitter, if found emission distance obviously
short or less sensitive, please change another same new battery. Please
have batteries for recycling.
Setting buttonSetting button
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ǂ Reorient or relocate the receiving antenna.
ǂ Increase the separation between the equipment and receiver.
ǂ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
ǂ Consult the dealer or an experienced radio/TV technician for help.