NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC6010 Emitter User Manual DC1660DC1662 A 01

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. Emitter DC1660DC1662 A 01

User Manual

Technical supportTFucntion instructionTechnical specificationInput voltage：3V(CR2430)Transmitting frequency：433MHzTransmitting power：10 milliwattOperating temperature：-100C—500CTransmssion distance：200 meters open office， 35 meters on two wallsCAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACEDBY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDINGTO THE INSTRUCTIONSNotice: transmitter do not exposed to moisture and strike, so as not toaffect life.When you use transmitter, if found emission distance obviouslyshort or less sensitive, please change another same new battery. Please have batteries for recycling.During the settings,the time between two operation must be shorter than4s,otherwise it will quit the settingAAdditionalfunctionAAdditionalfunctionMatchable R tubular motor setting upAAdditionalfunctionMatchable DC1680 setting upMatchable DC136 setting upPower onSound from motorhear long soundPower onPower onPress (up+down)×1 at the same timeIndicatorflashingIndicator long flashingIndicator flashing then extinguishedSettingis okSettingis okDuring the settings,the time between two operation must be shorter than6s,otherwise it will quit the settingDuring the settings,the time between two operation must be shorter than10s,otherwise it will quit the settingUp×1Down×1OKOKDelete all the datas of the motor andthe new emitter has been programmed.Beep once Beep onceSet up is ok.The up button controlthe motor clockwiseSet up is ok.The down button controlthe motor clockwiseSetting button×1OKDC136 DC136 DC136 DC136 DC136Stop×1OKDC1680 DC1680 DC1680 DC1680 DC1680IndicatorflashingIndicator long flashingIndicator flashing then extinguishedStop×1Up×1Run or beepfor hintRun or beepfor hintUp×1P2×1 P2×1Type specificationTVersion NO. : A/005-channel emitterDC6010 is 5-channel emitter,red light represents the currently selected channel, press the current channel again, cancel selected channel, when all the red light is bright, on behalf of the group control state. Press stop, up, down key when the red light fast flash tips.DC6010Emitter SpecificationBackBracket12345STOPLEDChannel selection}12345STOP12345STOP12345STOP12345STOPUp button Down buttonWhen you press the Setting button, the required use of tools,don’t be too sharp tool.Settingbutton(P2)
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Navigation menu