NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DC908B DC908B User Manual eDD1520 DD1522 A 00

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. DC908B eDD1520 DD1522 A 00

Manual

Step 1 To pair a remote to a shade 1. Press and hold the learning buon on the motor unl it jogs and beeps 1 me 2. Press P2 on the remote (shade will jog and beep) 3. Press P2 on the remote (shade will beep) 4. Press the up or down arrow (shade will jog and beep 6 mes) The remote is now linked to the shade/motor(NOTE: If shade travels in opposite direcon, PRESS and HOLD learning buon for 2 jogs and 2 beeps then release. This will reverse motor direcon). ( 2 Channel Up Down Stop Up + Stop Together = P2 LESS than 2 sec) UP DOWNP2 Channel selecon 15 Channel 1. 2. 3. Step 2 Limit seng ModePress P2 on the remote (shade will jog and beep)Press the up arrow on the remote (shade will jog and beep)Press P2 on the remote (shade will jog and beep 4 mes to confirm you are in the limit seng mode) You can now set the limits Step 3 Seng Limits 1. Using the up or down buons move the shade to the desired upper or lower posion (for fine adjustment press P2 while shade is in moon, this will send shade into incremental jogging) press stop buon when desired limit is reached. Aer correct limit posion is reached, press the stop buon 5 mes (shade will jog and beep 1 me) indicang that the limit is set. 2. Using the up or down buons move the shade to the desired upper or lower posion (for fine adjustment press P2 while shade is in moon, this will send shade into incremental jogging) press stop buon when desired limit is reached). Aer correct limit posion is reached, press the stop buon 5 mes (shade will jog and beep 1 me) indicang that the limit is set. 3. If limits need to be adjusted aer seng, go back to “limit seng Mode” and follow “seng Limits” Adding a remoteStart with the remote that currently works with the shade 1. Press P2 on working remote (shade will jog and beep) 2. Press P2 on working remote (shade will jog and beep) 3. Press P2 on remote to add (shade will jog and beep 7 mes) Controlling mulple shades on a single channel (All day/All night) 1. Locate shade number on controller, press P2 ( shade will jog and beep) 2. Press P2 again (shade will jog and beep) 3. Scroll through channels unl desired “ALL” channel number is reached 4. Press P2 to add control of that shade to the specific channel number (shade will jog and beep 7 mes)5. Now that shade is controlled with the original channel number and the second “All” channel buon 6. Repeat 1 - 4 above with up to 20 individual motors per channel. Removing a remote 1. Start with the remote that currently works the shade2. Press P2 on working remote 3. Press P2 on working remote 4. Press P2 on the remote to delete Replacing a lost remote If a shade has been previously programmed but the remote has been lost 1. Press the learning buon on the motor for 1 jog and beep 2. Press the up and down buons on the new remote (shade will jog and beep) 3. The new remote has been added to the shade. The shade will have the same sengs as with the previous remote.Adjusng Motor Speed Slow - Standard - Fast To raise speed, press UP + STOP together, (for 2 channel remote you must press buons for MORE than 2 sec), motor will jog to confirm To reduce speed, press DOWN + STOP together, motor will jog to confirm What Motor Jogs Mean 1. A single jog = To “pair” a remote to a new motor2. Two jogs = Reverse motor direcon 3. Three jogs = Factory reset

Navigation menu