NINGBO DOOYA MECHANIC and ELECTRONIC TECHNOLOGY DV50112 DC Venetian Blinds Drive User Manual DM35 45 ECA Y

NINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY CO., LTD. DC Venetian Blinds Drive DM35 45 ECA Y

User manual

1. Optrating: ①The valid interval of the emitter button is 6s,the emitter will quit the set after 6s. ②The motor will run for hint,please do the next step after the hint.2. Set limit position： ①Befor use,you have to set up/down limit position,and it is invalid when the up/down limit and the third limit are at the same locateon. ②Atter limit setting,with power and memory function. ③It will exit limit setting when program there is no operation for 2 minutes. ④It will delete every memory and restore the factory settings.3. If the emitter lost,please set up again with new emitter. Note：The motor DV50CE can be charged by both the power adapter DC240(I/J/K) or the 12V supply electricity.Product introductionOne Electronic motor maximum can store 20 channels,over 20 channels,if still need add new channels,it will be repeating covered in turn from second channel.Product features：The reverse of direction settingCan set and delete motor limit positionThe third limit position settingCan match code,add code and delete codeLimit positionOnly Dot-move & light-adjust function DV50CE-0.6N/10r0.6N.m12V0.5AVenetian Blinds Motor-DV50CESpecification（A-03)DC240(I/J/K)-550Operating temperatureParametersTypeRated Torque(N.m)Rated Current(A)Rated Voltage(V)READINGOperation noteMotor Installation
Press 2S Loosen P1Press 5S Loosen P1Press 8S Loosen P1Short press P1Repeating up,stop downSet up is okSuccessful change the directionActivate is okEvery perssing2, The reverse of direction setting3, Restore factory settings4, Short press functionP1 button setting1 Setting upP2MP2Lithium Cell3VP2UpStopDown SettingbuttonOPERATION GUIDEButton specificationsettingsuccessfulP21, Go into limit-setting modeP2P2→Up→P2Up→Stop→StopsettingsuccessfulDown→Stop→StopONRun for hint x1Run for hint x1Run for hint x2Run for hint x3Run for hint x1Press 3Run for hint x1Press 3P2 P2P2 →P2 →P2 OFFONT≥10S T＜10sPower onP2→P2→Up/ P2→P2→DownSet up is okP2 P2P2 →P2 →P2 OrP2 P2P2P2 →P2 →P2 ON6 Delete limitONP2 P2The limit is deletedP2→Down→P2 Emitter adding is okPress 2sLoosenPress 2sLoosenP25 Delete all emitterP2 P2P2→Stop→P2 Note：Can use DC1331.+Emitter adding is ok7 Dot-move setting+Go into adjustment modeJog increasing the distance a stall+Go into adjustment modeJog distance the decreases a stallPress the button corresponding to the sceneNote：①This operation is void under sleeping status; ②Must be in active status, this operation is valid.P2 P2Set up is okOrNote: When the transmitter will not be prompted to rotate once, does not turn the transmitter when prompted. With special transmitter instructionsRun to a preset first sceneThe first sceneOrThe first scene is memorized positionNote:①After a short time you press a scene setting, motor running position automatically to the first scene, the other profiles and so on; ②Motor at the corresponding point of the scene (the scene has been set for this point), press the corresponding scene button, the motor rotates one time, this position is deleted scenes; ③Special remote control for theDC2150I,DC2150J,DC2152J,DC2152I.Common troubleshooting1PHENOMENON REASON PROCESSING METHODNUMBERThe motor is not runninga，Set up the match codeb，Contact the engineers for after-salesa，The emitter is not matched.b，If press P1 button for a long time while with no reaction.may be the power is short-ciralit or the ciralit board or the motor is broken.Setting button(P1)Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Run for hint x1Press 1s Press 1s Press 1sPower onPower onPress 1s Press 1s Press 1sPress 1sPress 1sPress 1s Press 1sRun for hint x1Run for hint x1Run for hint x1Press 1s Press 1s Press 1sRun for hint x1Run for hint x1Run for hint x1Press 1s Press 1s Press 1sRun for hint x1Run for hint x1Run for hint x1Press 1sRun for hint x1Press 1sRun for hint x1Press 1sRun for hint x1Press 1sRun for hint x1Press 1sPress 1s Press 1s2 Add EmitterNote:Emitter is the one already matched code, while emitter has not.3 Limit positionPower onRun for hint x1Run for hint x1Run for hint x1Press 1s Press 1s Press 1sGo into limit-setting mode Follow step 22, Set up limit position3, Set down limit positionPress 1s Press 1sThe blind run up The blind stopConfirm the Blindto stop in the uplimit positionThe uplimit pointPress 1s Press 1sThe blind run downThe blind stopConfirm the Blindto stop in the downlimit positionThe downlimit point4 Delete one emitterOne emitter is deletedThe emitters all deletedNote: with the same method,you only can delete the emitter not the emitter1, Activate motor for the first timeAlready set up, down limit position

Navigation menu