NINGBO FOREVER ELECTRONIC APPLIANCE AMAS-2618 Remote Control for Mattress Inflation Air Pump User Manual

NINGBO FOREVER ELECTRONIC APPLIANCE CO., LTD. Remote Control for Mattress Inflation Air Pump

user manual

     AMAS-2618 Mattress Inflation Air Pump Instruction                                  一、Brief Introduction  Amas-2618 air mattress pump can adjust hardness degree with the two ways mattress, so as to achieve the best sleep state. Our product uses the newest wireless remote  control  technology,  and  MCU  control  technology,  easy  and  convenient operation, beautiful and lavish in product, it’s an ideal mattress pump.  二、Technical Parameters:  Model: AMAS-2618  Voltage: DC12V /Remote Control:DC 3V Pressure: 5-60mbar  Flow: 20LPM  Power: 25W  Standby Power:2.5W  Weight:2.3Kg  Contour Dimension:;Length260*Wide155*High105mm
     三、Remote Control Diagram:      LCD Display    Inflation    Memory Value    L/R Channel    Deflation             四、Operation Instruction:  1.  Pump connected with mattress: Remove dust cover of one corresponding outlet and connect the mattress. 2. Power on: Light shows r ed for 30s af ter power is on (Time fo r RC calibrating) .  Pump is in holding state and gets ready when light turns to g reen. Using the RC w hile  LED flashes with green, it means pump is working or transforming data with RC.  3. Remote control lighted by pr essing any button, LCD shows to  work and it g ets dormancy without any operating in 10s.  4. Inflation and deflation: Press L/R button to  choose the wanted mattress, press   Inflation button, it starts inflating and th e data of LC D shows increasing,  when  reaches to t he appropriate pressure, it will stop  inflating with pressi ng any key; press   the Deflation button, it starts deflating and  the data of LCD shows de creasing, when  reaches to the ap propriate pressure, it will stop deflation when pr ess any butt on; Users  can do the same method to inflate or deflate another mattress by pressing L/R button.
    5. Memory value: press Memory button afte r choosing the wanted mattress, LCD shows Memory and starts inflating or de flating, once it gets th e memory data it will stop(reset 25mbar, cut the power of RC it returns to the reset data)  6. Memory save: Press  Memory button for 3s in the data showing state when the RC flashes or stops working,  LCD shows “Memory” and flas h to “Save”, d ata will be memorized and saved as a new one. Use the same method to another.   五、Pay attention:  1.This RC can control 5 to 10 meters, it shows“Er”when out of the distance, please use it in its range.  2. Restart the remote co ntrol coding: This  remote control and pump ar e coded be fore  leaving the factory, when RC needs a replacem ent that requires use r to calib rate the  code. Method as follows: Connect the pow er and during the 30s w hen light shows red,   please press any button the RC lighted. Next st ep is pres s Memory button first then  press L/R button for 3S, and LCD will show SU, it means coded successfully.  3. Two AAA-LR03-1.5V batteries are fitted for this RC; LCD  will show the signal of i ts low power and please change the batteries in time to avoid damage. Without any using in the long time please remove out the batteries.   FCC Statement: This equipment has been tested and found to comply with the lim its for Part 15 of the FCC rules. These lim its are designed to pr ovide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can  radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  measures: •  Reorient or relocate the receiving antenna. •  Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help.
  This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device m ay not cause harmful interference, and (2) this devic e must accept any interference received, including interference that m ay cause undesired operation.  Note: Modifications to this product will vo id the u ser’s authority to oper ate this equipment.

Navigation menu