NX System NX-100 PROXIMITY ACCESS READER User Manual Product parameters
NX System Inc. PROXIMITY ACCESS READER Product parameters
user manual
User’s Manual
13.56MHz Contactless Smart Card
Reader
Table of Contents
1. Important Safety
Instructions........................................................................3
2. General.............................................................................3
3. Features.............................................................................4
4. Identifying Supplied Parts................................................4
5. Specification........................................................................5
6. Installation............................................................................6
7. Wire Color Table .................................................................8
8. Output Format......................................................................9
9. Wire Connection to Access Controller .............................10
10. Operation...........................................................................10
11. FCC Registration Information........................................12
12.Warranty and Service ................................................ .....13
1. Important Safety Instructions
When using the 13.56MHz [MIFARE] Contactless Smart Card Reader,
basic safety precautions should always be followed to reduce the risk of fire,
electrical shock, and injury to persons. In addition, the following should also
be followed:
Fully read and understand all instructions and follow them completely.
Follow all warnings and instructions marked on the product.
Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. If
necessary, use mild soap.
Do not use this product near water.
Only operate this product using the type of power source indicated. If you are not
sure of the type of power supplied to your installation site, consult your dealer of
local power company.
Never insert objects of any kind into the product or through the cabinet slots as
they may touch voltage points and/or short circuit parts possibly resulting in fire
or electric shock. Never spill liquid of any kind on the product.
Never disassemble this product by yourself; take the unit to a qualified service
center whenever service or repair is required. Opening or removing the covers
may expose you to dangerous voltages or other risks. Also, incorrect reassembly
can cause electric shock when the unit is subsequently used.
Unplug this product from the Direct Current (DC) power source and refer to
qualified service personnel under these conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product does not operate normally after following the operating
instructions in this
manual.
Adjust only those controls that are covered by the operating instructions
in this manual.
Improper adjustment of other controls that are not covered by this
manual may damage
the unit and will often require extensive work by a qualified technician to
restore normal
operation.
d. If the product exhibits a distinct change in performance.
2. General
The IDTECK SR10 Smart Card Reader can be compatible with Philips
Mifare™ Card. The unit provides integrated operation of reader and is
designed by which can install easily to door frame or wall. The IDTECK SR10
is elegant looking and built in an attractive 10cm (4") read range smart card
reader. It reads sector numbers from Philips Mifare™ compatible cards and
transmits the data to the control panel in various output formats. Three LED
indicators (red and green) and inside Piezo buzzer sound will guarantee you
an accurate and reliable system operations.
3. Features
- 13.56MHz [MIFARE] Contactless smart Card Reader / Writer
-ISO 14443 type A compatible
-Sector Number Read only
-Read Range: Up to 3 inch (6cm)
.- 26bit Wiegand Output Format
.- 3 Array LED Indicators (Red and Green) and Beeper
.-External LED Control
.-External Buzzer Control
- Easy to install on Mullion Mounting suitable
-Solid Epoxy Potted
.- Waterproof / IP65 / IP66
.- Warranty: Life Time
-Reverse Polarity Protection
-Compatible Software: Smart Card Read / Write Software
- Compatible Controller: iCON100SR, iTDC-SR, Third Party Controller
4. Identifying Supplied Parts
Please unpack and check the contents of the box:
5. Specification
Model SR10
Reading Time (Card) 30ms
Power / Current DC12V / Max.80mA
Input Port 2ea (External LED Control, External Buzzer
Control)
Output Format 26bit Wiegand
LED Indicator / Beeper 3 Array LED Indicators (Red, Green) / Piezo
Buzzer
Operating Temperature -35° to +65℃ (-31° to +149℉)
Operating Humidity 10% to 90% relative humidity non-condensing
Color / Material Dark Peal Gray / Polycarbonate
Dimension (W x H x T) 47mm X 115mm X 22 mm (1.8’’ X 4.5’’ X 0.88’’)
Weight 150g (0.33lbs)
Index of Protection IP65 / IP66
Certification FCC, CE, MIC
6. Installation
6-1. Mullion/Wall Mount: Drill two 6-32 or M3 screws 3.3" (8.38cm) apart in
vertical and drill one 1/2" hole for the reader cable 1.7" (4.31cm) apart
from the top hole. (Skip this step, if you have installed an electric gang
box.)
6-2. Put reader cable into the center hole and install the reader module by
using two 6-32 or M3 screws. 6-3. Put bezel into the reader module, then push
bezel until you hear the locking sound.
6-4. Installation consideration
6-4-1. Installation of SR10 on metal Read range will be reduced if located on
metal surfaces or in the vicinity of metal objects. The amount of
reduction will be a factor of the amount of metal and the distance the
Reader is from the metal. Metal near the Reader absorbs energy from
the Reader excite field and affects the signal being received from the
card by re-directing excite field transmissions into the receiver circuitry.
Moving the Reader away from the metal objects reduces energy loss.
Try to limit the amount of metallic materials installed near the SR10.
Use a plastic electrical box if possible. When installing the Reader on
metal door frame, add Isolation Spacers between the Reader and metal
door frame. If you do so, read range reduction can be improved. The
typical read distance specification (2-4 inches at 12VDC) refers to
operation without metal in the vicinity of the Reader. The read distance
will be reduced if metal is installed nearby. The SR10RW generate a
magnetic field on all sides of the Reader. Any metal that conducts
electricity, especially metal that contains iron, steel or copper will
interfere with the field and reduce the effective spacer between the
Reader and the metal object.
① Installation of two readers side by side and back to back Read range is not
affected if the side by side distance between two readers is equal to or
greater than eight inches (20cm). If the distance between the two readers is
less than eight inches (20cm), field interference between the two readers may
result in a double-badge read.
When installing two readers back-to-back on a wall that will separate the two
readers by eight inches (20cm) or less, a metal plate (for example: Reader
isolation plate, metal wall) must be placed between the readers. To obtain the
maximum read range, mount each proximity reader onto one or more Isolation
Spacers.
7. Wire Color Table
8. Output Format
SIGNAL COLOR
Main Power (+12V) Red
Power Ground (GND) Black
Wiegand Data 0 Out Green
Wiegand Data 1 Out White
Buzzer Control In Blue
LED Control In Yellow
* Please cut out tail connector before
installation.
8-1. 34/26bit Wiegand Output Format
1. 1. Data format
2. 2. Timing diagram
26bit Wiegand output format 34bit Wiegand output format
Bit 1 Even parity of bit 2 ~ bit
13 Bit 1 Even parity of bit 2 ~ bit 17
Bit 2∼9 Facility code (000 ~ 255)
Bit 2∼25
4byte ID number
(0000000001 ~
4,294,967,295)
Bit 10∼25
ID
number
(00000 ~
65,535)
ID number
(00000 ~
65,535)
Bit 26 Odd parity of bit 14 ~ bit
25 Bit 34 Odd parity of bit 18 ~ bit 33
9. Wire Connection to Access Controller
10. Operation
10-1. Apply power and you can see the 3-Array red LED is on, indicating the
reader is on ‘Standby ’.
10-2. Present a proximity card to the reader until you hear a beep sound
and the LED changes the color to green simultaneously and the reader
sends the RF card data to the controller. Then the LED changes the color
to red again for next reading. All 3 LEDs are off when you have access to
card and then are on orderly from left.
10-3. LED Control: To be off the LEDs, you may connect the LED Control
Input (Yellow wire) to the power ground. Then the green LED is on.
Present a proximity card. The LED changes the color to red
simultaneously, then to green again for next reading. All 3 LEDs are off
when you have access to card and then are on orderly from left.
10-4. Buzzer Control: When the reader reads a proximity card, only one beep
sound generates in normal operating mode but you can generate more
beep sounds to distinguish whether the access is granted or denied. To
generate more beeps, you may control the Beeper Control Input (Blue
wire) to the power ground, then you can turn the beeper on while you hold
the Beeper Control Input to the power ground.
11. FCC Registration Information
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which
are not expressly approved by the manufacturer for compliance could
void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
12. Warranty and Service
The following warranty and service information applies only to the United
States of America and Republic of Korea. For the information in other
countries, please contact your local distributor. To obtain in or out of
warranty service, please prepay shipment and return the unit to the service
facility listed below.
Headquarters: IDTECK Co., Ltd.
5F Ace Techno Tower B/D,
684-1 Deungchon-Dong, Gangseo-Gu,
SEOUL, KOREA 157-030
Tel: +82-2-2659-0055
Fax: +82-2-2659-0086
E-mail: webmaster@idteck.com
Website: www.idteck.com
U.S Branch: RF Logics Inc.370 Amapola Ave, #106
Torrance, CA 90501
Tel: 310-782-8383
Fax: 310-782-8298
E-mail: rflogics@rflogics.com
Website: www.rflogics.com
Hong Kong Branch: IDTECK Hong Kong
12/F, B2B Centre, No.36 Connaught Road West, Hong Kong
Tel: 852-2581-9580
Fax: 852-2234-5150
E-mail: alchu@qala.com.hk
Website: www.ristarhk.com
Please use the original container, or pack the unit(s) in a sturdy carton with
sufficient packing to prevent damage, include the following information:
1. 1. A proof-of-purchase indicating model number and date of purchase.
2. 2. Bill-to address.
3. 3. Ship-to address.
4. 4. Number and description of units shipped.
5. 5. Name and telephone number of person to contact.
6. 6. Reason for return and description of the problem.
NOTE: Damage occurring during shipment is deemed the responsibility of
the carrier, and claims should be made directly to the carrier.
The specification contained in this manual are subject to change without
notice at any time.
5F, Ace Techno Tower B/D, 684-1,
Deungchon-Dong, Gangseo-Gu, Seoul,
157-030, Korea
Tel : +82-(2)-2659-0055 Fax : +82-(2)-2659-0086 E-mail :
webmaster@idteck.com